seccion de referencias

165

6.1.1 / 6.1.2Seccin de Referencias

Reportes de Evaluacin de ICBO / Aprobaciones COLA

Manual Tcnico de Productos Hilti 2002

6.1.1 Reportes de Evaluacin de la Conferencia Internacional de Servicios de Evaluacin de Oficiales de laConstruccin (ICBO ES)

6.1.2 Aprobaciones de la Ciudad de los ngeles (Aprobaciones COLA)

Reporte No. Ttulo

1290 Exterior or Perimeter Sill and Interior Plate Anchorages

2388 Low-Velocity Powder Actuated Drive and Hilti Pneumatically Driven Fasteners

2895 HDI Concrete Expansion Anchors

3987 HILTI HSL Carbon Steel and Stainless Metric Heavy Duty Concrete Anchors

4016 HIT C-100 Adhesive Anchor System

4373 Steel Diaphragms Attached with Hilti Powder Actuated or Pneumatically Driven Fasteners

4627 Kwik Bolt II and Post Nut Kwik Bolt II Concrete Anchors

4780 Kwik-Flex Structural Fasteners

4815 HIT HY 20 Adhesive Anchor System for Unreinforced Masonry

5193 Hilti HIT HY 150 Adhesive Anchor Systems

5224 HCKB Kwik-Bolt Concrete Anchor

5259 Kwik-Con II Concrete and Masonry Screw Anchors

5264 Three-Eighths-Inch HDI-P Concrete Anchor

5369 HVA (HVU) Adhesive Anchor System

5457 Hilti Low-Velocity Powder Actuated Ceiling Clip Assemblies

5605 Hilti HSE 2421 Adhesive Anchoring System

5608 Hilti HDA Metric Self-Undercutting Concrete Anchors

5942 Hilti HIT-TZ Adhesive Anchors

Reporte No. Ttulo

2582 Hilti Powder Driven Fasteners

23709 Hilti HDI Concrete Expansion Anchors

24397 HIT C-100 Adhesive Anchors

24564 HY 20 for URM

166

Aprob. COLA / del Condado Metro Dade y Listados ULSeccin de Referencias

6.1.2 / 6.1.3 / 6.1.4


6.1.3 Aprobaciones del Condado de Metro Dade

6.1.4 Listados de Underwriters Laboratories (UL)

Reporte No. Ttulo

01-1001.03 Kwik Bolt II Concrete Expansion Anchor

00-0411.06 Powder Driven Fastener (X-ZF 72 P8S36)

01-0727.01 Hilti KWIK-CON II Concrete Screw Anchor

01-1119.03 HIT HY 150

Aplicacin Producto

EX2258 Pipe Hangers

Powder Actuated FastenersEW10-30-15P10, W10-30-27P10,W10-30-32P10 and W10-30-42P10

EX2709 Pipe HangersHilti Kwik Bolt II Anchors 3/8" to 3/4" DiametersHilti HDI Anchors 3/8" to 3/4" DiametersHilti Sleeve Anchors 1/2" to 3/4" Diameters

R13203 Roof Deck Construction No. 58, 87, 156, and 157Powder Actuated and Pneumatic Driven FastenersENP2-21 L15, ENPH2-21 L15, ENP2K-20 L15,X-EDNK22 THQ12, X-EDN19 THQ12

E217969 Power Fastened HangersHilti X-JH/C, X-JH/W, X-RH 1/4-C, X-RH 1/4-W,X-RH 3/8-C, X-RH 3/8-W

6.1.2 Aprobaciones de la Ciudad de los ngeles (COLA) (continuacin)

Reporte No. Ttulo

25095 Kwik-Flex Structural Fastener

25226 Kwik-Bolt II and Post Nut Kwik Bolt II Expansion Anchor

25257 Hilti HIT HY 150 Adhesive Anchor System

25290 HSL Metric Heavy Duty Concrete Anchors

25291 HCKB Ceiling Concrete Anchor

25296 Hilti Powder Actuated Fasteners for Steel Diaphragm Attachment

25350 Hilti HDI-P Concrete Anchors

25363 HVA / HVU Adhesive Anchor System

25408 HSE 2421 Adhesive Anchor System

25422 HDA Undercut Anchor

167

6.1.5 / 6.1.6Seccin de Referencias

FRMC / SBCCI


6.1.6 Conferencia Internacional de Cdigos de Construccin del Sur (SBCCI)

Reporte No. Descripcin

9930 Approval for Powder Actuated Fastening and Anchoring Systems

6.1.5 Aprobaciones de Factory Mutual Research Corporation (FMRC)

Aplicacin Producto

Pipe Hangers Hilti HDI Anchors 3/8" to 3/4" DiametersHilti Kwik Bolt II Anchors 3/8" DiameterW10-30-27P10,W10-30-32P10,W10-30-32P10K,W10-30-37P10W10-30-42P10,W10-30-47P10, EW10-30-15P10Hilti HDI-P

Roof Systems ENP2-21 L15, ENPH2-21 L15, ENP2K-20 L15, X-EDN19 THQ 12, X-EDNK22 THQ12

168

ASTM Estndares para MaterialesSeccin de Referencias

6.2.1


6.2.1 ASTM estndares para materiales

Estndar Ttulo

A36 Specification for Structural Steel

A108 Specification for Steel Bars, Carbon, Cold-finished, Standard Quality

A193 Specification for Alloy-Steel and Stainless Steel Bolting Materials for High-Temperature Service

A240 Specification for Heat-resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels

A276 Specification for Stainless and Heat-resisting Steel Bars and Shapes

A307 Specification for Carbon Steel Bolts and Studs, 60,000 psi Tensile Strength

A493 Specification for Stainless and Heat-resisting Steel for Cold Heading and Cold Forging Bar and Wire

A510 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

A563 Specification for Carbon and Alloy Steel Nuts

A615 Specification for Deformed and Plain Billet-Steel Bars for Concrete Reinforcement

A616 Specification for Rail-Steel Deformed and Plain Bars for Concrete Reinforcement

A617 Specification for Axle-Steel Deformed and Plain Bars for Concrete Reinforcement

B86 Specification for Zinc-Alloy Die Castings

C33 Specification for Concrete Aggregates

C62 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)

C90 Specification for Load-Bearing Concrete Masonry Units

C307 Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts and Monolithic Surfacings

C330 Specification for Lightweight Aggregates for Structural Concrete

C332 Specification for Lightweight Aggregates for Insulating Concrete

C476 Specification for Grout for Masonry

169

6.2.1Seccin de Referencias

ASTM Estndares para Materiales


6.2.1 ASTM Estndares para Materiales (continuacin)

Estndar Ttulo

C580 Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts,Monolithic Surfacings, and Polymer Concrete

C579 Test Method for Compressive Strength of Chemical Resistant Mortars, Grouts, Monolithic Surfacasand Polymer Concretes

C881 Specification for Epoxy-Resin-Base Bonding Systems for Concrete

C882 Test Method for Bond Strength of Epoxy-Resin Systems Used with Concrete

C1002 Standard Specifiction for Steel Drill Screws for the Application of Gypsum Board of Metal Plaster Bases

D570 Test Method for Water Absorption of Plastics

D638 Test Method for Tensile Properties of Plastics

D648 Test Method for Deflection Temperature of Plastics Under Flexural Load

D695 Test Method for Compressive Properties of Rigid Plastics

D1652 Test Method for Epoxy Content of Epoxy Resins

D2240 Test Method for Rubber PropertyDurometer Hardness

D2393 Test Method for Viscosity of Epoxy Resins and Related Components

D2566 Test Method for Linear Shrinkage of Curved Thermosetting Casting Resins During Care

D2842 Test Method for Water Absorption of Rigid Cellular Plastics

E380 Standard Practice for Use of the International System of Units, SI (The Modernized Metric System)

E488 Test Method for Strength of Anchors in Concrete and Masonry Elements

E1190 Test Methods for Strength of Powder-Actuated Fasteners Installed in Structural Members

E1512 Standard Test Methods for Testing Bond Performance of Bonded Anchors

F436 Specification for Hardened Steel Washers

F563 Specification for Steel Nuts

F593 Specification for Stainless Steel Bolts, Hex Cap Screws and Studs

F594 Specification for Stainless Steel Nuts

170

ASTM Estnd. de Recub. / Espec. Federales / Normas ANSI Seccin de Referencias

6.2.2 / 6.2.3 / 6.2.4


6.2.2 ASTM Estndares de Recubrimientos

Estndar Ttulo

A153 Zinc Coating (Hot-Dip) on Iron and Steel Hardware

B633 Electrodeposited Coatings of Zinc on Iron and Steel

B695 Coatings of Zinc Mechanically Deposited on Iron and Steel

F1941 Standard Specification for Electrodeposited Coatings on Threaded Fasteners (Unified Screw Threads,UN/UNR)

6.2.3 Especificaciones Federales

Estndar Ttulo

FF-S-325 Shield, Expansion; Nail Expansion; and Nail, Drive Screw (Devices,Anchoring, Masonry)(Cancelled)

FF-P395C Pin, Drive Guided and Pin Drive, Powder Actuated (Fasteners for Power Actuated and Hand Actuated Fastening Tools)

A-A-1922A Shield, Expansion (Caulking Anchors, Single Lead)

A-A-1923A Shield, Expansion (Lag, Machine and Externally Threaded Wedge Bolt Anchor)

A-A-1924A Shield, Expansion (Self Drilling Tubular Expansion Shell Bolt Anchors)

A-A-55615 Shield, Expansion (Wood Screw and Lag Bolt Self-Threading Anchors)

A-A-55614 Shield, Expansion (Wood Screw and Lag Bolt Self-Threading Anchors)

6.2.4 ANSI - Normas

Norma Ttulo

A10.3 Powder-Actuated Fastening Systems Safety Requirements

B18.2.2 Square and Hex Nuts (Inch Series)

B18.22.1 Plain Washers (Inch Series)

B212.15 Carbide-Tipped Masonry Drills and Blanks for Carbide Tipped Masonry Drills

Standard 61 Drinking Water System Components Health Effects

171


Conversiones Mtricas y sus Equivalentes


ConversinEl Acto de la Conversin Mtrica del 1975, fueamendado por el Acto del 1988 de Omnibus Tradeand Competitiveness, el cual establece el SI(Sistema Internacional) sistema mtrico como elsistema preferido de medidas en los EstadosUnidos

Muchos de los productos estn siendo fabricadosy suministrado en medidas mtricas SI o durastales como los pernos de anclajes de 10mm,12mm, 26mm etc en dimetro. Cuando el sistemapulgadas-libras se da, la conversin suave sepuede utilizar en la mayora de los productos. Losdimetros de la conversin mtricas para pernosde anclajes se demuestran en la Tabla 1. Losfactores estndar de conversin que se usancomnmente en los productos de fijacin sedemuestran en la Tabla 2.

Tabla 1 Dimetros

Sistema de Conversin Ut. para Conv.Pulg.-Libra Mtrica Dura Mtrica Suave

plgd. mm mm

1/4 6.35 65/16 7.94 83/8 9.52 101/2 12.70 125/8 15.88 163/4 19.05 201 25.40 25

1 1/4 31.75 32

Tabla 2Unidades imperiales a unidades SI

Para Convertir A Multiplique Por

Longitud pulgada (plgd) milmetro (mm) 25.4000

pies metro (m) 0.3048

Area pulgada cuadrada (plgd.2) milmetro cuadrado (mm2) 645.1600

pulgada cuadrada (plgd.2) centmetro cuadrado (cm2) 6.4516

pies cuadrado (pies2) metro cuadrado (m2) 0.0929

Volumen pulgada cbica (plgd.3) centmetro cbico (cm3) 16.3871

pies cbica (pies3) metro cbico (m3) 0.0283

galn (U.S.) litro (L) 3.7854

Fuerza libra de fuerza (lbf) neutn (N) 4.4482

libra de fuerza (lbf) kiloneutn (kN) 0.0044

Preson libra/pulgada cuadrada (psi) neutn/milmetro cuadrada (N/mm2) 0.0069

libra/pulgada cuadrada (psi) mega pascal (MPa) 0.0069

KIP/pulgada cuadrada (ksi) mega pascal (MPa) 6.8946

libra/pies cuadrado (psf) neutn/milmetro cuadrado (N/m2) 47.8801

Torque o Movimiento a Doblar

pies libra (pies-lb) metro neutn (Nm) 1.3558

pulgada libra (plgd-lb) metro neutn (Nm) 0.1130

Corte del Diafragma

libras/pies (pies-lb) metro neutn (N/m) 14.5939

172

Conversiones Mtricas y sus EquivalentesSeccin de Referencias

6.3.1


Table 3Unidades SI a Unidades Imperiales

Para Convertir A Multiplique Por

Longitud milmetro (mm) pulgada (plgd.) 0.0394

metro (m) pies 3.2808

Area milmetro cuadrado (mm2) pulgada cuadrada (plgd.2) 0.0016

centmetro cuadrado (cm2) pulgada cuadrada (plgd.2) 0.1550

metro cuadrado (m2) pies cuadrado (pies2) 10.7639

Volumen centmetro cbico (cm3) pulgada cbica (plgd.3) 0.0610

metro cbico (m3) pies cbico (pies3) 35.3147

litro (L) galn (U.S.) 0.2642

Fuerza neutn (N) libra de fuerza (lbf) 0.2248

kiloneutn (kN) libra de fuerza (lbf) 224.8089

Presin neutn/milmetro cuadrado (N/mm2) libra/pulgada cuadrada (psi) 145.0400

mega pascal (MPa) libra/pulgada cuadrada (psi) 145.0400

mega pascal (MPa) KIP/pulgada cuadrada (ksi) 0.1450

neutn/metro cuadrado (N/m2) libra/pies cuadrado (psf) 0.0209

Torque o Movimiento a Doblar

metro neutn (Nm) pies libra (pies-lb) 0.7376

metro neutn (Nm) pulgada libra (plgd-lb) 8.8496

Corte del Diafragma

metro neutn (N/m) libras/pies (pies-lb) 0.0685

173


Propiedades Mecnicas de Materiales


Designacin Tamao Nominal Resistencia Mn. de Fluencia Resistencia ltima Mn.del Grado (plgd.) ksi (MPa) ks (MPa)

ASTM A36 Todos 36 (248) 58 (400)ASTM A193, B7 1/4 hasta 21/2 105 (724) 125 (862)AISI 1038 (As Recd) 1/4 a 11/4 41 (282) 75 (517)AISI 11L41 Sobre 5/8 hasta 1 75 (517) 90 (620)AISI 1110 M (As Recd) 1/4 a 5/8 44 (303) 53 (365)AISI 12L14 5/8 hasta 11/2 60 (414) 78 (538)AISI 1010 (As Recd) 1/4 hasta 3/4 44 (303) 53 (365)ASTM A307 1/4 to 4 60 (414)ASTM A325 1/2 hasta 1 92 (634) 120 (827)

over 1 hasta 11/2 81 (558) 105 (724)ASTM A449 1/4 hasta 1 92 (634) 120 (827)

over 1 hasta 11/2 81 (558) 105 (724)SAE Grado 2 1/4 hasta 3/4 57 (393) 74 (510)

over 3/4 to 11/2 36 (248) 60 (414)SAE Grado 5 1/4 hasta 1 92 (634) 120 (827)

over 1 to 11/2 81 (558) 105 (724)SAE Grado 8 1/4 hasta 11/2 130 (896) 150 (1034)ISO 898 Clase 5.8 Todos 58 (400) 72.5 (500)ISO 898 Clase 8.8 Todos 92.8 (640) 116 (800)

Acero Carbn

Designacin del Acero Tamao Nominal Resistencia de Fluencia Resistencia ltimaASTM/AISI (plgd.) ksi (MPa) ksi (MPa)

F593 / 304 / 316 1/4 hasta 5/8 65 (448) 100 (689)3/4 hasta 11/2 45 (310) 85 (586)

A193, B8/304/316 1/4 hasta 11/2 30 (205) 74.6 (515)A276 / 304 1/4 hasta 9/16 76 (524) 90 (620)

Sobre 9/16 64 (441) 76 (524)A276 / 316 1/4 hasta 9/16 76 (524) 90 (620)

Sobre 9/16 64 (441) 76 (524)A493 / 304 Todos 60 (414) 100 (689)A582 / 303 Todos 60 (414) 100 (689)DIN 267 Todos 65.3 (450) 101.5 (700)Part 11, A4-70

Acero Inoxidable

174

Datos de Rosca de PernosSeccin de Referencias

6.3.3


Dimensiones Bsicas para la Serie de Roscas Gruesas UNC ANSI B1.1-1982

No. 10 0.1900 0.1449 24 0.0284 0.0145 0.0175No. 12 0.2160 0.1709 24 0.0366 0.0206 0.0242

1/4 0.2500 0.1959 20 0.0491 0.0269 0.03185/16 0.3125 0.2524 18 0.0767 0.0454 0.05243/8 0.3750 0.3073 16 0.1104 0.0678 0.0775

7/16 0.4375 0.3602 14 0.1503 0.0933 0.10631/2 0.5000 0.4167 13 0.1963 0.1257 0.1419

9/16 0.5625 0.4723 12 0.2485 0.1620 0.18195/8 0.6250 0.5266 11 0.3068 0.2017 0.22603/4 0.7500 0.6417 10 0.4418 0.3019 0.33457/8 0.8750 0.7547 9 0.6013 0.4192 0.46171 1.0000 0.8647 8 0.7854 0.5509 0.6057

11/8 1.1250 0.9704 7 0.9940 0.6929 0.763311/4 1.2500 1.0954 7 1.2272 0.8896 0.9691

TamaoNominal

Roscas porplgd. (n) Nominal

plgd.2Menorplgd.2

Resistencia a laTraccin plgd.2

Mayorplgd. (D)

Menorplgd.

Dimetro Bsico Area*

* rea Menor = 0.7854 (D - 1.3)2n

rea de Traccin = 0.7854 (D - 0.9743)2n

THREADPITCH

Basicmajor

diameterBasicpitch

diameterMinor

diameter

INCLINACIN

DE LA ROSCA

Dimetrobsicomayor

Dimetrobsico deinclinacin

Dimetromenor

Perfil Bsico de las Roscas de los TornillosUN, UNR y M (mtrico)

* rea Fuerza Tensil = 0.7854 (D - 0.9382 P)2

Dimetro Bsico Paso de Area*Medida Mayor Menor Rosca Nominal FuerzaNominal mm (D) mm mm (P) mm2 Tensil mm2

M8 8 6.62 1.25 50.3 36.6

M10 10 8.34 1.50 78.5 58.0

M12 12 10.07 1.75 113.1 84.3

M16 16 13.80 2.00 201.1 157.0

M20 20 17.25 2.50 314.2 245.0

M24 24 20.70 3.00 452.4 353.0

Mtrica de Dimensiones Bsicas para Serie Roscada M ANSI B1.13M-1979

175


Datos de Barra de Refuerzos en Concretos


Dimensiones NominalB

Designacin de Peso Nominal Dimetro rea Permetrola BarraA lb/pie plgd. plgd.2 plgd.

3 0.376 0.375 0.11 1.1784 0.668 0.500 0.20 1.5715 1.043 0.625 0.31 1.9636 1.502 0.750 0.44 2.3567 2.044 0.875 0.60 2.7498 2.670 1.000 0.79 3.1429 3.400 1.128 1.00 3.544

10 4.303 1.270 1.27 3.99011 5.313 1.410 1.56 4.43014 7.65 1.693 2.25 5.3218 13.60 2.257 4.00 7.09

Dimensiones Bsicas ASTM para Barras de Acero Deformado para Refuerzo en Concreto, Unidades Pulgadas-Libras

A. La designacin de los nmeros de la barras son basados en un octavo de pulgadas en el dimetro nominal.B. La dimensin nominal de una barra deformada es equivalente a aquellos de una barra redonda sencilla que tiene el mismo peso por libra que la barra deformada..

Dimensiones NominalB

Designacin de Masa Nominal Dimetro rea Permetrola BarraA kg/m mm mm2 mm

10 0.560 9.5 71 29.913 0.994 12.7 129 39.916 1.552 15.9 199 49.919 2.235 19.1 284 59.822 3.042 22.2 387 69.825 3.973 25.4 510 79.829 5.060 28.7 645 90.032 6.404 32.3 819 101.336 7.907 35.8 1006 112.543 11.38 43.0 1452 135.157 20.24 57.3 2581 180.0

Dimensiones bsicas ASTM para barras de acero deformado para refuerzo en concreto, Unidades SI

A. La designacin de los nmeros de la barras son aproximadamente el nmero de milmetros del dimetro nominal de la barraB. La dimensin nominal de una barra deformada es equivalente a aquellos de una barra redonda sencilla que tiene el mismo peso por metro que la barra deformada.

176

PerforacinSeccin de Referencias

6.4


6.4.1 Tolerancia de Brocas Hilti con punta de carburo

TE-C (SDS+) Fraccional Cdigo Referencia Prof. Efectiva

256099 TE-CX 3/16-4 2"

205299 TE-CX 3/16-6 4"

256100 TE-CX 3/16-8 5 1/2"

256101 TE-CX 3/16-12 9 1/2"

256102 TE-CX 3/16-16 13 1/4"

205309 TE-CX 1/4-4 2"

205310 TE-CX 1/4-6 4"

205311 TE-CX 1/4-8 5 1/2"

256106 TE-CX 1/4-12 9 1/2"

205316 TE-CX 5/16-6 4"

205320 TE-CX 5/16-12 9 1/2"

256107 TE-CX 5/16-18 13 1/4"

205324 TE-CX 3/8-6 4"

205326 TE-CX 3/8-12 9 1/2"

205327 TE-CX 3/8-18 13 1/4"

205328 TE-CX 3/8-24 21 1/4"

205339 TE-CX 7/16-6 4"

205340 TE-CX 7/16-18 15 1/4"

205352 TE-CX 1/2-6 4"

205354 TE-CX 1/2-12 9 1/2"

205355 TE-CX 1/2-18 15 1/4"

28040 TE-C+ 9/16-6 3 1/2"

28041 TE-C+ 9/16-12 9 1/2"

28042 TE-C+ 9/16-18 15 1/4"

28043 TE-C+ 5/8-8 5 1/2"

28044 TE-C+ 5/8-12 9 1/2"

28045 TE-C+ 5/8-18 15 1/4"

28047 TE-C+ 11/16-12 9 1/2"

28048 TE-C+ 11/16-18 15 1/4"

28618 TE-C-S 3/4-8 5 1/2"

28619 TE-C-S 3/4-12 9 1/2"

28620 TE-C-S 3/4-18 15 1/4"

28621 TE-C-S 13/16-18 15 1/4"

28622 TE-C-S 27/32-8 5 1/2"

28623 TE-C-S 27/32-12 9 1/2"

28624 TE-C-S 7/8-10 7 1/2"

28625 TE-C-S 7/8-18 15 1/4"

28626 TE-C-S 1-10 7 1/2"

28627 TE-C-S 1-18 15 1/4"

28060 TE-C+ 1-27 24 1/4"

TE-C (SDS+) MtricaCdigo Referencia Prof. Efectiva

205322 TE-C+ 8.5/17 4"

205331 TE-CX 10/22 6"

205342 TE-CX 12/17 4"

205343 TE-CX 12/22 6"

205344 TE-CX 12/27 7 1/2"

205257 TE-CX 14/22 5 9/10"

205358 TE-CX 14/27 7 7/8"

205360 TE-CX 14/47 15 3/4"

205366 TE-CX 15/27 7 7/8"

205372 TE-CX 16/17 4"

28002 TE-C-S 18/22 6"

28004 TE-C-S 20/22 6"

28005 TE-C-S 20/32 10"

28011 TE-C-S 24/27 7 1/2"

28016 TE-C-S 28/27 7 1/2"

1. Dimetro en mm, Longitud en cm Para obtener ms informacin sobre dimetros y longitudes de brocas, por favor consulte el Catlogo de Productos Hilti o comunquesecon Servicio al Cliente.

TE-T Fraccional*Cdigo Referencia Prof. Efectiva

00338410 TE-TX 1/4-9 4"

0038411 TE-TX 5/16-15 10"

00335915 TE-TX 3/8-9 4"

00335916 TE-TX 3/8-15 10"

00335917 TE-TX 3/8-21 16"

0038412 TE-TX 7/16-9 4"

00333471 TE-T 1/2-9" 4"

00333472 TE-T 1/2-13" 7 3/4"

00333473 TE-T 1/2-21" 15 3/4"

00332981 TE-T 9/16-13" 7 3/4"

00333474 TE-T 9/16-21" 15 3/4"

00333475 TE-T 5/8-9" 4"

00331901 TE-T 5/8-13" 7 3/4"

00333476 TE-T 5/8-21" 15 3/4"

00333478 TE-T 11/16-21" 16"

00333479 TE-T 3/4-13" 8"

00331902 TE-T 3/4-21" 16"

00333480 TE-T 13/16-21" 16"

00333481 TE-T 27/32-13" 8"

00333482 TE-T 7/8-13" 8"

00333483 TE-T 7/8-21" 16"

00333484 TE-T 1-13" 8"

00333485 TE-T 1-21" 16"

00333486 TE-T 1 1/8-17" 11 1/4"

00333487 TE-T 1 1/8-23" 17 1/4"

00333488 TE-T 1 1/4-15" 9 1/2"

00333489 TE-T 1 1/4-23" 17 1/4"

TE-T (SDS max) Mtrica*Cdigo Referencia Prof. Efectiva

00333740 BIT TE-TX 12/23 5 9/10"

00333741 BIT TE-TX 12/33 7 7/8"

00333744 BIT TE-TX 14/23 5 9/10"

00333745 BIT TE-TX 14/33 7 7/8"

00333747 BIT TE-TX 15/23 5 9/10"

00333748 BIT TE-TX 15/33 7 7/8"

00333750 BIT TE-TX 16/23 5 9/10"

00307202 BIT TE-T 18/32 7 7/8"

00307204 BIT TE-T 20/32 7 7/8"

00307205 BIT TE-T 20/52 15 3/4"

00307208 BIT TE-T 24/32 7 7/8"

00307211 BIT TE-T 28/32 7 7/8"

00307213 BIT TE-T 32/37 9 27/32"

00307214 BIT TE-T 32/56 17 11/16"

* Para usar con martillo combi TE 35 de Hilti1. Dimetro en mm, Longitud en cm

* Para usar con Martillo combi TE 35 de Hilti

177

6.4Seccin de Referencias

Perforacin


6.4.1 Tolerancia de Brocas Hilti con punta de carburo

TE-Y (SDS max) Fraccional Cdigo Referencia Prof. Efectiva

00220632 TE-Y 1/2-13 7"

00220633 TE-Y 1/2-21 16"

00220634 TE-Y 9/16-13 7"

00220635 TE-Y 9/16-21 16"

00220636 TE-Y 5/8-13 7"

00220637 TE-Y 5/8-21 16"

00220638 TE-Y 5/8-36 30 1/2"

00220639 TE-Y 11/16-21 16"

00220640 TE-Y 3/4-13 7"

00220641 TE-Y 3/4-21 16"

00220642 TE-Y 3/4-36 30 1/2"

00220643 TE-Y 13/16-21 16"

00220644 TE-Y 27/32-13 7"

00220645 TE-Y 27/32-21 16"

00220646 TE-Y 7/8-13 7"

00220647 TE-Y 7/8-21 16"

00220648 TE-Y 7/8-36 30 1/2"

00220649 TE-Y 1-13 7"

00220650 TE-Y 1-21 16"

00229651 TE-Y 1-36 30 1/2"

00220664 TE-Y 1 1/16-17 10 3/4"

00220653 TE-Y 1 1/8-17 10 3/4"

00220654 TE-Y 1 1/8-23 17 5/8"

00220665 TE-Y 1 1/8-36 30 1/2"

00220655 TE-Y 1 1/4-15 8 3/4"

00220656 TE-Y 1 1/4-23 17 5/8"

00220657 TE-Y 1 1/4-36 30 1/2"

00220658 TE-Y 1 5/16-23 17 5/8"

00220659 TE-Y 1 3/8-23 17 5/8"

00220660 TE-Y 1 3/8-36 30 1/2"

00220661 TE-Y 1 1/2-17 10 3/4"

00220662 TE-Y 1 1/2-23 17 5/8"

00220663 TE-Y 1 9/16-23 17 5/8"

TE-Y (SDS max) MtricaCdigo Referencia Prof. Efectiva

00333753 TE-YX 12/35 7 7/8"

00333756 TE-YX 14/35 7 7/8"

00333757 TE-YX 14/55 15 3/4"

00333758 TE-YX 15/35 7 7/8"

00333760 TE-YX 16/35 7 7/8"

00028709 TE-Y 18/34 7 1/4"

00028714 TE-Y 20/32 6 1/2"

00028715 TE-Y 20/52 14 1/2"

00028720 TE-Y 24/32 6 1/2"

00028721 TE-Y 24/52 14 1/2"

00028725 TE-Y 28/32 6 1/2"

00028729 TE-Y 32/37 9 1/2"

00028730 TE-Y 32/57 17 1/4"

00028733 TE-Y 37/57 17 1/4"

00028734 TE-Y 37/92 30 1/2"

1. Dimetro en mm, Longitud en cm Para obtener ms informacin sobredimetros y longitudes de brocas, por favor consulte el Catlogo de ProductosHilti o comunquese con Servicio al Cliente.

seccion de referencias

Documents