paso a paso mantto

FUERZA AEREA COLOMBIANA MANTENIMIENTO PROGRAMADO

AERONAVE MATRICULA SERIE TIPO DE INSPECCIÓN: INSPECCION 300 HORAS FECHA INIC. / TERM. PUB HOJA Nº 1

:

TAREASNIVEL

PERICIA REQ

ACCIÓN CORRECTIVA FECHAHORA INICIO

HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

PT6T-3DF MANUAL ENGINE -INSPECTION/CHECK CAP 72-00-00 TABLE 601

EXHAUST DUCT FOR CRACKS AND DISTORSION 3

P3 FILTER HOUSING AND TUBING (PRE SB5367 FOR CONTAMINATION AND FLUSH

3

P3 AIR FILTER ELEMENT CLEAN ELECTROSONIC AND VISUALLY

3

P3 AIR FILTER DRAIN VALVE CLEANING AND INSPECT.

3

FAC 4 201T SEPT-2008 V.B JEFE CONTROL MANTENIMIENTO



:

TAREASNIVEL

PERICIA REQ


HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

FUEL SURGE ACCUMULATOR FOR SIGNS OF METAL DISTORTION ON THE SIDES AND END. 3

FUEL SURGE ACCUMULATOR. REPLACE ACCUMULATOR IF POP-OUT INDICATOR IS EXTENDED. 3

FIRESEALS FOR CRACKS AN SECURITY OF BRACKETS 3

WIRING CHECK FOR SECURITY OF ACCESIBLE CONNECTIONS, CLAMPS AND BRACKETS AND FOR EVIDENCE OF WEAR, CHAFING CRACKS AND CORROSION

3

INLET SCREEN FOR CLEANLINESS AND CONDITION OF MESH.

3




:

TAREASNIVEL

PERICIA REQ


HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

CHECK FOR BROKEN AND OR MISSING WIRE MESH SEGMENTS AND SIGNS OF BRITTLENESS. IF YOU SUSPECT AN AREA, CHECK THE INTEGRITY OF MESH BY MANIPULATING AND FLEXING THE SCREEN, ANY DEVIATION IS CAUSE FOR REPLACEMENT

GAS GENERATOR CASE FOR CRACKS, DISTORTION, CORROSION AND EVIDENCE OR OVERHEATING

3

OUTPUT SHAFT SEAL FOR OIL LEAKS 3

TUBBING.

1. CHECK RESISTENCE OF LEAD AND HEATING ELEMENT OF HEATED PNEUMATIC TUBES (REF 73-10-08).

3

2. CHECK FOR SECURITY OF ALL ACCESIBLE CONNECTIONS, CLAMPS AND BRACKETS

3




:

TAREASNIVEL

PERICIA REQ


HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

EVIDENCE OF WEAR, CHAFING, CRACKS , CORROSION ADN EVIDENCE OF FUEL AND OIL LEAKS.

OIL FILTER ELEMENT CLEAN AND INSPECT FOR ELECTROSONIC METHOD.

3

CHIP DETECTORS (ACCESORY AND REDUCTION GEAR BOX) CHECK FOR METALLIC PICK-UP AND CLEAN USING LINT-FREE CLOTH.

3

BLEED AIR CASE ASSY CHECK THE ORIENTATION OF BLEED AIR CASE ASSY REF 72-20-00

3

IGNITION SYSTEM UNITS FOR SECURITY 3




:

TAREASNIVEL

PERICIA REQ


HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

SPARK IGNITERS FOR CLEANLINESS AND CONDITION. FUNCTIONAL CHECK REF 74-00-00

3

COMPRESSOR INLET AREA CHECK FOR CORROSION, DIRT DEPOSITS AND EROSION AND CHECK FIRST STAGE BLADES

3

P3 AIR TUBE METTERING TEES FOR CONTAMINATION AND CLEANLINESS

3

MFCU THROTTLE SHAFT. WITH POWER SECTIONS SHUT DOWN AND FUEL BOOST PUMP ON, CHECK BOTH SIDES OF TRHOTTLE SHAFT FOR FUEL LEAKAGE.

3

AFCU CHECK FOR BEARING WASH-OUT INDICATED BY BLUE DYE( GREASE AND FUEL MIXED) AT AFCU VENT HOLE

3




:

TAREASNIVEL

PERICIA REQ


HORA TERMIN.

HORAS HOMBRE

Nº SAP OPERARIO

FIRMA

No SAP FIRMA Y

SELLO INS.

FUEL PUMP CHECK FOR SECURITY AND FUEL LEAKS 3

FUEL PUMP FILTER FOR CONTAMINATION AND DAMAGE.

NOTE: HELICOPTERS EQUIPPED WITH FUEL FILTER IMPENDING BYPASS INDICATING DEVICE MAY ELECTTO WAIVE THIS INSPECTION AND TO PERFORM THE FUEL PUMP FILTER REPLECEMENT AT 600 HOURS.

3

OIL TO FUEL HEATER. INMEDIATELY AFTER SHUTDOWN: CHECK TEMPERATURE OF HEATER AT FUEL OUTLET. IF GREATER THAN 140 ª F( 60ªC) REPLACE ELEMENT.

3


paso a paso mantto

Documents