*

*

*

* Impulsa al camion para el movimiento hacia adelante o hacia atrs Proporciona frenado dinmico para moverse hacia adelante. Cambia la energa del motor al generador. (Frena al Camin a una velocidad segura antes de utilizar los frenos de servicio)

Proporciona los medios de fijacin de los neumticos al bastidor del camin.

*VENTAJASCostos de reparacion relativamente bajo

Mas revisiones en la vida del motor.DESVENTAJASElementos de desgaste carbones y colector (conmutador)Descargas destructivas de la suciedad y desgaste (Flashovers)

*

*

*

*Document All Measurements & Findings.Clean & Dry.

Planetary Bearing Bore Inspection & Measurements.3 Inboard & 3 Outboard BoresMAGNETIC FRAME INSPECTIONTap Out All Planetary Retainer Holes & Plug with Plastic Plugs.*Replace (36) Inboard & Outboard Pinion Bearing Cap Bolts.

Inspect & Measure Inboard & Outboard Hub Bearing Surfaces.Inspect Wear Band Mounting Area.Inspect & Pressure Test Brake Line Piping.MAGNETIC FRAME INSPECTION*

Inspect Copper Bars & Insulation for wear & damage (Insulate Again if Necessary). Remove/Clean, Inspect & Measure Hub Bearings (Replace if Necessary).MAGNETIC FRAME INSPECTION*

*Inspect Seal Mounting Area.Inspect & Measure Main Gear Area.Clean and Thoroughly Dry Unit.Document All Measurements & Findings.

*

*

Inspect & Measure Hub-Bearing Mounting Bores.WHEEL HUB INSPECTION*

Inspect Wheel Rim Mounting Surface (Repair if Needed).Remove All Old Wheel Clamp Studs.Tap All Wheel Rim Clamp Stud Holes.WHEEL HUB INSPECTION*7) Install New Studs.

Clean & Dry Thoroughly.Inspect/Measure & Record Inboard/Outboard Bearing Surfaces.PLANETARY GEAR INSPECTION*

Inspect/Measure Gear & Pinion Teeth.NDT Inspection of Gear Teeth.

PLANETARY GEAR INSPECTION*

*

*

*CLEAN, INSPECT, TEST & RECONDITION - ARMATURE

*Document all Readings and Findings.Steam and Bake Dry.

*Inspect & Measure Shaft Bearing and Spline Fits.Opposite Comm EndComm End

*Check Shaft Run-Out.Measure, NDT & Record Spline Fits (Pin Check) of Shaft, Sun Pinion & Coupling.

*Varnish Treat & Bake Dry The Armature.Conduct Electrical Tests For The 2nd Time.Turn, Undercut & Balance The Commutator.Conduct Electrical Tests For 3rd Time.Document all Measurements & Findings. BASIC ELECTRICAL REBUILD PROCESS(Compare Test Results of Test #2 to Test #3)

*Set Magnetic Frame Vertical with Gear Case Up.Install Bearings on Planetary Gears.

*Installing Planet Bearing Assemblies In Frame.

*Reposition Magnetic Frame 180 with Leveling Feet Attached.Level Magnetic Frame.Install Wear Bands.Install Seals in Torque Tube.FINAL ASSEMBLY

*Install Torque Tube.

Install Seal Ring.*

* Install Wheel Hub Bearings & Grease.

* Install Wheel Hub.

*Inner Bearing/Support Assembly Install Greased Inner Bearing on the Electric Motor Cartridge.MAGNETIC FRAME INSTALLATION

* Install the Electric Motor Cartridge in Magnetic Frame.

* Install Bearing, Frame-Head & Break Support.

* Install Armature in the Electric Motor Cartridge/Magnetic Frame.

INSTALLING ARMATURE IN MOTORGuiding Armature In*

INSTALLING ARMATURE IN MOTOR*

* Turn the Magnetic Frame From Vertical to Horizontal Position.

REPOSITIONING MOTOR*

*

* Install Brush Holders, Brushes and Air Baffles.

*Completed Installation

Seat Brushes. Install Sun Pinion. Install Gear Case Cover. Install Insulators, Jumper Bars & Cables on Back Cover.ASSEMBLY*

* Electrical Test & Record Measurements. Test Run 1 Hour in Each Direction. Drain Oil Reservoir. Label Reservoir With Tag Fill Before Run. Paint/Stencil. Fill Oil Reservoir.* Install on Shipping Skid. Shrink Wrap Both Ends.READY FOR SHIPMENT!ASSEMBLY

*ELECTRICAL PROCESS TOOLING Commutator Turning Lathe Commutator Under-Cutter Armature Balancing Equipment

* Brush Seating Tools And Materials Megger

H-E PARTS/DOM-EXSTANDARD WARRANTY*

*

*

*

******************************************