configuracion_ma5616_s100

8/15/2019 Configuracion_MA5616_S100

1/25

----------------------------CONFIGURACION MA5616 - FTTC----------------------------

==============================Cambio a protocolo SIP===================================enableconfig

protocol support sipy

save

reboot system

=============================Configuracion Autosave ===========================================

enableconfig

autosave interval on

==========================Confirmacion de tarjetas de servicio=========================

board confirm 0

==================Cuando sube el equipo por GPON=======================================

port mode 0/0 0 gpon

port mode 0/0 1 gpon

==========================Asignacion de Nemonico=======================================

* El nombre del equipo varia segun dataplan

sysname Bquilla_Metropolitano_De_Suba

==========================Configuracion Zona Horaria=======================================

timezone GMT- 5:00

======================Asignacion descripcion del puerto================================

* Se le debe poner descripcion al puerto de uplink del equipo , la descripcion e


2/25

s el nombre de la OLT y el puerto al que se conecta.

port desc 0/0/0 description TUN-CEN_3/1/5

==========================Comisionamiento Gestion======================================

**** Las vlans, Direcciones Ips y Gateways varian segun dataplan. En el siguiente caso IP: 10.33.23.3 , GATEWAY: 10.33.23.1 , MASCARA: 29

enable

config

Vlan 2 Standar

Interface vlan-if 2

ip address 10.33.23.3 29

quit

port vlan 2 0/0 0

port vlan 2 0/0 1

ip route-static 0.0.0.0 0.0.0.0 10.33.23.1

=============================Configuracion vlan de servicio============================

* La vlan de servicio varia segun dataplan. En el siguiente ejemplo la VLAN de servicio es 3012.

vlan 3012 smart

vlan attrib 3012 stacking

port vlan 3012 0/0 0


============================Configuracion multi-service-port==========================

* La vlan de servicio varia segun dataplan. En el siguiente ejemplo la VLAN de servicio es 3012.

multi-service-port vlan 3012 board 1 vpi 8 vci 35 rx-cttr 6 tx-cttr 6y



3/25



stacking label vlan 3012 baselabel 100y

============================Configuracion VLAN 3400 para servicio VOIP==========================

*La siguiente configuracion siempre debe hacerse, la VLAN nunca cambia.

vlan 3400 smart







traffic table ip cir 256 priority 6 priority-policy tag-In-Package

=================================Usuarios de Gestion===================================

terminal user nameSigrest3l3c0n1c4#t3l3c0n1c4#root34SIGRES


4/25

terminal user namegestiongestion1234gestion1234root24gestion

terminal user namemanttoT3l3c0m.T3l3c0m.root1

3mantto

terminal user passwordrootmduadmindsl4m0v1st4rdsl4m0v1st4rn

================================Perfiles de Navegacion=================================

adsl line-profile add 199yspeed_128K1y01110y10101y60316031y32


5/25

1603264

y

adsl line-profile add 2ySpeedy1y011112y8

031803129212ny224125032896

y

adsl line-profile add 6ySpeedy_20481y011112y80318031292


6/25

12ny2242500321300

y

adsl line-profile add3ySpeedy_4M1y

011112y6031603139012y606000y2245000321300

y

adsl line-profile add 989ySpeedy_6M1y01111


7/25

2y6031603139012ny22478001281300

y

adsl line-profile add4ySpeedy_8M1y011112y6031603139012y606000y22410000321500

y


8/25

adsl line-profile add 988ySpeedy_10M1y011112y603160

3139012ny224130001281300

y

adsl line-profile add 987ySpeedy_11M1y011112y6031603139012ny22414300


9/25

1281300

y


y6031603139012ny224169001281300

adsl line-profile add8ySpeedy_14M1y011112y603160313


10/25

9012y606000y22414000321300

y

adsl line-profile add

9ySpeedy_18M1y011112y6031603139012y606000y22418000321300

y

adsl line-profile add 20ySpeedy_20M1


11/25


12/25

y011112y6031603139012n

y22439001281300

y


y


13/25


3139012ny22491001281300

y



14/25

117001281300

y


y6031603139012ny224156001281300

y



15/25

9012ny224195001281300

y

====================Comisionamiento Anexo M Prueba 20 M================================

adsl extline-profile add 4yAnnexM_prueba

nnnnny44y9nnnnnnnnnnn

==============================Comunidades SNMP========================================

snmp-agent community read public

snmp-agent community write private

snmp-agent community read totem_ro

snmp-agent sys-info version v1 v2c

snmp-agent target-host trap-hostname Netcool address 10.30.4.132 trap-paramsname Netcool

snmp-agent target-host trap-hostname SAS address 10.30.4.155 trap-paramsname SAS

snmp-agent target-host trap-hostname SIGRES1 address 192.168.254.143 trap-params


16/25

name SIGRES1

snmp-agent target-host trap-hostname SIGRES2 address 192.168.254.144 trap-paramsname SIGRES2



snmp-agent target-host trap-hostname Primaster address 10.30.7.10 udp-port 162 trap-paramsname Primaster

snmp-agent target-host trap-hostname Secmaster address 10.30.7.11 udp-port 162 trap-paramsname Secmaster

snmp-agent target-host trap-paramsname Primaster v1 securityname aaa

snmp-agent target-host trap-paramsname Secmaster v1 securityname aaasnmp-agent trap enable standard

=============================Servidor radius==========================================

radius-server template radius2radius-server shared-key t3l3c0mradius-server authentication 10.30.4.253 1812 undo radius-server user-name domain-includedradius-server traffic-unit mbyte

quit

radius-server template radius1radius-server shared-key t3l3c0mradius-server authentication 10.30.4.115 1645

undo radius-server user-name domain-includedradius-server traffic-unit mbyte

quitaaa authentication-scheme huawei authentication-mode radius

quitdomain telecom authentication-scheme huawei radius-server radius2 quitquit

======================Cambio de perfil de puertos 1M============================


17/25

=======

* Se debe probar la navegacion de 1 M en todos los puertos anteriormente enviados

interface adsl 0/1

deactivate all

activate all profile-index 2

quit

interface adsl 0/2

deactivate all


quit

interface adsl 0/3

deactivate all


quit

interface adsl 0/4

deactivate all


quit

======================Ejemplo Configuracion de 1 Puerto a 20M===================================

*A continuacion un ejemplo de configuracion de un puerto a 20 M, para estas pruebas se deberan configurar los puertos anteriormente enviados. Para el siguienteejemplo se configurará el puerto 1 de la tarjeta 1

interface adsl 0/1

deactivate 1

activate 1 profile-index 20

extline-config 1 profile-index 4

quit


18/25

================SI EL EQUIPO TIENE TARJETAS DE VOZ CONFIGURAR LO SIGUIENTE==========================

=============================Configuracion vlan de Voz===============================

* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.9.200 Gateway : 10.220.9.193 Mascara: 27

vlan 70 smart

interface vlanif 70

ip address 10.220.9.200 27

quit

port vlan 70 0/0 0port vlan 70 0/0 1

ip route-static 10.220.0.0 255.255.255.0 10.220.9.193

===========================Configuracion voip=========================================

* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.9.200 Gateway : 10.220.9.193

voip

ip address media 10.220.9.200 10.220.9.193 ip address signaling 10.220.9.200 qos ip media 10.220.9.200 dscp 46 qos ip signaling 10.220.9.200 dscp 26

quit

==========================Configuracion interface SIP=================================

* Las direcciones IPs y Gateway varian segun dataplan. En la siguiente configuracion IP : 10.220.9.200

interface sip 0y

if-sip attribute basic media-ip 10.220.9.200 signal-ip 10.220.9.200 signal-port 5060 home-domain ims.movistar.co

if-sip attribute basic primary-proxy-ip1 10.220.0.12 primary-proxy-port 5060

if-sip attribute basic sipprofile-index 0

if-sip attribute optional sub-ua-profile disable sdp-negomode local


19/25

if-sip attribute optional proxy-check-mode option

if-sip attribute optional proxy-dual-home no proxy-refresh-mode no-switch

fax-modem parameters vbd-codec G.711U

rfc2833 set rfc2833-negomode negostart

mg-software parameter 2 1



sipprofile delete codec-pri all

sipprofile add codec-pri 0 18 20

sipprofile add codec-pri 1 4 30 sipprofile add codec-pri 2 0 20

sipprofile add codec-pri 3 8 20

sipprofile modify syspara 63 30














digitmap-timer short 5

mg-software strpara 5 57

mg-software strpara 6 1


20/25

fax-modem parameters negomode self-switch rtp-interval 3

fax-modem parameters rtp-interval 3

resety

quit

oversea parameters 0 670

============================Reinicio de tarjetas=======================================

board reset 0/1yboard reset 0/2yboard reset 0/3yboard reset 0/4y

================================Pruebas internas=======================================

*Para el siguiente caso las pruebas internas se configuran para la tarjeta 3

undo port vlan 70 0/0 0

undo port vlan 70 0/0 1

esl user

sippstnuser batdel 0/3/0 0/3/63y

sippstnuser batadd 0/3/0 0/3/63 0 telno 100

quit

UNA VEZ FINALIZADAS LAS PRUEBAS SE DEBE REALIZAR LA SIGUIENTE CONFIGURACION PARA PODER REALIZAR PRUEBAS CON NUMEROS REALES

port vlan 70 0/0 0

port vlan 70 0/0 1


21/25

esl user

sippstnuser batdel 0/3/0 0/3/63y

======================Configuracion numeros de prueba==================================

**** Despues de configurado alguno de los numeros con los comandos mas abajo listados, con el siguiente comando se puede verificar si el numero registra para poder hacer las pruebas

MA5600T(config)#display sippstnuser reg-state 0/15 -------------------------------------------------------- F /S /P MGID RegisterState TelNo

-------------------------------------------------------- 0 /3/0 0 Active 5724064998 --------------------------------------------------------

esl user

sippstnuser add 0/3/0 0 telno 5724064998

sippstnuser auth set 0/3/0 telno 5724064998 password-mode [email protected]

sippstnuser rightflag set 0/3/0 telno 5724064998 ct disable dc disable conf disable cw enable








22/25





sippstnuser auth set 0/4/0 telno 5747813604 password-mode password

[email protected]











23/25
















24/25














sippstnuser rightflag set 0/11/0 telno 5747813600 ct disable dc disable conf dis


25/25

able cw enable

======================Configuracion Alarmas Externas==================================

* Antes de configurar las alarmas externas se debe verificar que la emu 1 sea la ESC, se puede verificar con el comando MA5616(config)#display emu , de lo contrariose debe cambiar el id para entrar a configurar la EMU, es decir, si esta configurada con el ID 0 , el primer comando debe ser interface emu 0

interface emu 1

esc digital 0 name Temperature available-level low-level

esc digital 1 available-level low-level

esc digital 2 name SPD available-level low-level

esc digital 3 name Wiring available-level low-level

configuracion_ma5616_s100

Documents