cfd-s03cp (1)

SERVICE MANUAL

Sony CorporationPersonal Audio DivisionPublished by Sony Techno Create Corporation

Canadian ModelCFD-S03CP

AEP ModelCFD-S03CP/S03CPL

UK ModelE Model

Australian ModelCFD-S03CP

CD RADIO CASSETTE-CORDER

9-887-043-072007H04-1© 2007.08

Ver. 1.6 2007.08

SPECIFICATIONS

CFD-S03CP/S03CPL

CD player sectionSystem

Compact disc digital audio systemLaser diode properties

Emission duration: ContinuousLaser output: Less than 44.6 µW(This output is the value measured at a distance ofabout 200 mm from the objective lens surface on theoptical pick-up block with 7 mm aperture.)

Number of channels2

Frequency response20 - 20 000 Hz +1/–2 dB

Wow and flutterBelow measurable limit

Radio sectionFrequency range

FM: 87.5 - 108 MHzCND, E92, MX model:AM: 530 - 1 710 kHzTW model:AM: 531 - 1 611 kHzEXCEPT CND, E92, MX, TW model:AM/MW: 531 - 1 611 kHz (9 kHz step)

530 - 1 610 kHz (10 kHz step)CFD-S03CPL:LW: 153 - 279 kHz

IFFM: 10.7 MHzAM/MW/LW: 450 kHz

AntennasFM: Telescopic antennaAM/MW/LW: Built-in ferrite bar antenna

Cassette-corder sectionRecording system

4-track 2 channel stereoFast winding time

Approx. 150 s (sec.) with Sony cassette C-60Frequency response

TYPE I (normal): 80 - 10 000 Hz

GeneralSpeaker

Full range: 8 cm dia., 4 Ω, cone type (2)Outputs

Headphones jack (stereo minijack):For 16 - 32 Ω impedance headphones

Power output1.7 W + 1.7 W (at 4 Ω, 10% harmonic distortion)

Power requirementsFor CD radio cassette-corder:120 V AC, 60 Hz (CND, E92, MX, TW model)220 V AC, 60 Hz (KR model)220 – 230 V AC, 50 Hz (AR model)230 V AC, 50 Hz (EXCEPT E92, KR, MX, AR, TW model)9 V DC, 6 R14 (size C) batteriesFor remote control:3 V DC, 2 R03 (size AAA) batteries

CDModel Name Using Similar Mechanism CFD-S01

SectionCD Mechanism Type KSM-213CDP

Optical Pick-up Name KSS-213C

TC Model Name Using Similar Mechanism CFD-S01

Section Tape Transport Mechanism Type MF-S01

– Continued on next page –

Photo: CFD-S03CP

2

CFD-S03CP/S03CPL

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270˚C during

repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering or

unsoldering.

Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be damaged

by heat.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

Notes on DualDiscsA DualDisc is a two sided disc product which mates DVD recordedmaterial on one side with digital audio material on the other side.However, since the audio material side does not conform to theCompact Disc (CD) standard, playback on this product is notguaranteed.

Power consumptionAC 13 W (CND, E92, MX model)AC 12 W (EXCEPT CND, E92, MX model)

Battery lifeFor CD radio cassette-corder:

FM recordingSony R14P: approx. 6 h

Sony alkaline LR14: approx. 20 h

Tape playbackSony R14P: approx. 3 h

Sony alkaline LR14: approx. 12 h

CD playbackSony R14P: approx. 1.5 h

Sony alkaline LR14: approx. 4.5 h

DimensionsApprox. 360 × 141 × 235 mm (w/h/d)(incl. projecting parts)

MassApprox. 2.6 kg (incl. batteries)

Supplied accessoryAC power cord (1)Remote control (1)

Design and specifications are subject to changewithout notice.

• AbbreviationCND : Canadian modelE92 : AC 120V area in E modelKR : Korea modelMX : Mexican modelAR : Argentina modelTW : Taiwan model

Ver. 1.2

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCESSONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCESSONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUELOU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

3

CFD-S03CP/S03CPL

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 4

2. GENERAL ................................................................... 5

3. DISASSEMBLY3-1. Cabinet (Rear) Assy ......................................................... 73-2. Cabinet (Front) Assy, Cabinet (Upper) Assy ................... 73-3. Main Board ...................................................................... 83-4. CD Block Assy ................................................................ 83-5. BD83S Board .................................................................. 93-6. Optical Pick-up ................................................................ 93-7. Panel Board ..................................................................... 103-8. CD Lid ............................................................................. 103-9. Tape Mechanism Block, Belt (1), Belt (2) ...................... 113-10. TC Board ......................................................................... 113-11. Key-1 Board, Key-2 Board .............................................. 123-12. Power Board .................................................................... 12

4. MECHANICAL ADJUSTMENTS ......................... 13

5. ELECTRICAL ADJUSTMENTSTape Section .................................................................... 13Tuner Section ................................................................... 14CD Section ...................................................................... 16

6. DIAGRAMS6-1. Block Diagram – CD Section – ....................................... 176-2. Block Diagram – Main Section – .................................... 186-3. Circuit Boards Location .................................................. 196-4. Printed Wiring Board – BD83S Section – ....................... 206-5. Schematic Diagram – BD83S Section – .......................... 216-6. Printed Wiring Board – Main Section – .......................... 226-7. Schematic Diagram – Main Section (1/3) – .................... 236-8. Schematic Diagram – Main Section (2/3) – .................... 246-9. Schematic Diagram – Main Section (3/3) – .................... 256-10. Printed Wiring Boards – TC Section – ............................ 266-11. Schematic Diagram – TC Section – ................................ 276-12. Printed Wiring Boards – Panel Section – ........................ 286-13. Schematic Diagram – Panel Section – ............................ 296-14. Printed Wiring Boards – Power Supply Section – ........... 306-15. Schematic Diagram – Power Supply Section – ............... 31

7. EXPLODED VIEWS7-1. Rear Cabinet Section ....................................................... 397-2. Front Cabinet Section (1) ................................................ 407-3. Front Cabinet Section (2) ................................................ 417-4. Upper Cabinet Section (1) ............................................... 427-5. Upper Cabinet Section (2) ............................................... 437-6. CD Mechanism Section ................................................... 44

8. ELECTRICAL PARTS LIST .................................. 45

•UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

4

CFD-S03CP/S03CPL

Ref. No. TYPE A TYPE B

IC804 S-816A33AMC-BAI-T2-G NO MOUNT

IC806 NO MOUNT XC6202P332FR

R883 100k NO MOUNT

R884 220k NO MOUNT

SECTION 1SERVICING NOTES

CHUCK PLATE JIG ON REPAIRING

On repairing CD section, playing a disc without the lid (CD), useChuck Plate Jig.• Code number of Chuck Plate Jig: X-4918-255-1

LASER DIODE AND FOCUS SEARCH OPERATIONCHECK1. Turn ON the [OPERATE] button and press [CD] button to CD

position.2. Open the CD lid.3. Turn on SW2 with screwdriver, etc. as following figure.4. Press the N X (CD) button.5. Confirm the laser diode emission while observing the objecting

lens. When there is no emission, Auto Power Control circuit orOptical Pick-up is broken.Objective lens moves up and down three times for focus search.

SW2

NOTE FOR REPLACEMENT OF THE IC804 ANDIC806There have been changes to the 3.3V regulator circuit in the courseof production.When repairing the 3.3V regulator circuit, check which of TYPE Aor B is applicable as specified in the table below.

Ver. 1.4

5

CFD-S03CP/S03CPLSECTION 2GENERAL This section is extracted

from instruction manual.

Basic Operations

* qa, u 9 and n qs on the

Before using the unit

To turn on/off the powerEuropean model: Press OPERATE 1.Other models: Press POWER 1.

To adjust the volumePress VOLUME +, – (VOL +, – on the remote) qa.

To listen through headphonesConnect the headphones to the i (headphones) jack qf.

To reinforce the bass soundPress MEGA BASS 2.“MEGA BASS” appears in the display.To return to normal sound, press the button again.

Playing a CD/MP3 disc1 Press CD qd on the unit (direct power-on).

(On the remote, press OPERATE or POWER and 1

then press FUNCTION qh repeatedly until “CD” appears in the display.)

2 Press Z PUSH OPEN/CLOSE 8 on the unit, and place a disc with the label side up on the CD compartment.

To close the CD compartment, press Z PUSH OPEN/CLOSE 8 on the unit.

3 Press u 9.

The player plays all the tracks/MP3 files once.When you play a MP3 disc, MP3 indicator lights up after the player reads the file information.

Audio CD

Track number

Playing time

MP3 disc

MP3 file number

After the folder name*, song title and artist name are displayed, the playing time** will appear.

***

To PressPause playback u 9. To resume play, press it

again.

Stop playback x 9.

Go to the next track/MP3 file

> 7.

Go back to the previous track/MP3 file

. 7.

Select a folder on an MP3 disc

+ 0 on the unit to go forward and – 0 to go backward.

Play the selected folder only (MP3 disc only)

MODE 4 on the unit until “FLDR” appears, + or – 0 on the unit to select a folder and then u 9 to start playing.

Locate a point while listening to the sound

> (forward) or . (backward) 7 while playing and hold it until you find the point.

Locate a point while observing the display

> (forward) or . (backward) 7 in pause and hold it until you find the point.

Remove the CD Z PUSH OPEN/CLOSE 8 on the unit.

Tips•

•x9 in stop mode. When you open

Example of folder structure and playing orderThe playing order of the folders and files is as follows:

CD-RCD-RW

3

2

1

2

4

5

3

6

7

8

4

95

06

1

Folder

MP3 file

Notes on MP3 discs•

••

•

•

•

•

•

•

Listening to the radio1 Press RADIO•BAND•AUTO PRESET qd on the

unit (BAND qg on the remote) repeatedly (direct power-on).

Each time you press the button, the indication changes as follows:CFD-S03CPL: “FM” t “MW” t “LW”CFD-S03CP: “FM” t “AM”

2 Hold down TUNE + or – 0 until the frequency digits begin to change in the display.

The player automatically scans the radio frequencies and stops when it finds a clear station.If you can not tune in a station, press TUNE + or – 0repeatedly to change the frequency step by step.When an FM stereo broadcast is received, “ST” appears.

TipIf the FM broadcast is noisy, press MODE until “MONO” appears 4in the display and the radio will play in monaural.

Changing the AM/MW tuning intervalIf you need to change the AM/MW tuning interval, do the following:

1 Press RADIO•BAND•AUTO PRESET qd on the unit until “AM” or “MW” is displayed.

2 Press DISPLAY•ENTER 5 on the unit for 2 seconds.

3 Press RADIO•BAND•AUTO PRESET qd on the unit for 2 seconds.

“9K STEP” or “10K STEP” flashes.

4 Press PRESET + or – 7 on the unit to select “9K STEP” for 9 kHz interval or “10K STEP” for 10 kHz interval.

5 Press DISPLAY•ENTER 5 on the unit.After changing the tuning interval, you need to reset your preset AM/MW radio stations.

Playing a tapeUse buttons on the unit for the operation.

1 Press TAPE qd on the unit (direct power-on).

2 Press xZ qs on the unit, and insert the tape into the tape compartment with the side you want to play facing you. Use TYPE I (normal) tape only. Close the compartment.

Make sure there is no slack in the tape to avoid damaging the tape or the unit.

3 Press n qs.

The player starts playing.

To Press

Pause playback X qs on the unit. To resume play,press it again.

Stop playback xZ qs on the unit.

Fast-forward or rewind*

m or M (fast forward or rewind) qs on the unit.

Eject the cassette xZ qs on the unit.

* xZ qs to release m or qs.

Recording on a tapeUse buttons on the unit for the operation.

1 Press xZ qs on the unit to open the tape compartment and insert a blank tape with the side you want to record on facing you. Use TYPE I (normal) tape only. Close the compartment.

2 Select the program source you want to record.

To record from the CD player, insert a CD and press CD qd.To record from the radio, tune in the station you want.

3 Press z qs on the unit to start recording

(n is depressed automatically).

To Press

Pause recording X qs on the unit. To resume recording, press it again.

Stop recording xZ qs on the unit.

Tips•

•z qs in step 3, press MODE 4 on the unit to select the

•

•12 qd on the unit.3 z qs on the unit.

When the disc is inserted, the player reads all the files on that disc. During this time, “READING” is displayed. If there are many folders or non-MP3 files on the disc, it may take a long time for play to begin or for the next MP3 file to start play.We recommend that you do not save unnecessary folders or files other than MP3 ones in the disc to be used for MP3 listening.A folder that does not include an MP3 file is skipped.Maximum number of files: 255Maximum number of folders: 150 (including the root folder)Maximum number of folders and files in total: 256Maximum directory levels: 8Folder names and file names can be displayed with up to 30 characters including quotation marks.The characters A - Z, 0 - 9, and _ can be displayed on this player. Other characters are displayed as “_”.This player conforms to Version 1.0, 1.1, 2.2, 2.3 and 2.4 of the ID3 tag format. When the file has the ID3 tag information, “song title”, “artist name” and “album name” can be displayed and “ID3” appears in the display. If the file does not have the ID3 tag information, file name appears instead of song title, folder name appears instead of album name and “no artist” appears instead of artist name. The ID3 tag information can be displayed with up to 15 characters.When naming, be sure to add the file extension “mp3” to the file name.If you put the extension “mp3” to a file other than an MP3 file, the player cannot recognize the file properly and will generate random noise that could damage your speakers.The file name does not correspond to the ID3 tag.

Adjusting the volume or the audio emphasis will not affect the recording level.If the AM/MW/LW program makes a whistling sound after you’ve press position of ISS (Interference Suppress Switch) that most decreases the noise.For the best results, use the AC power as a power source for recording.To erase a recording, proceed as follows:

Insert the tape whose recording you want to erase.Press TAPE Press

When the tape is wound to the end, press M

Playback starts from the track/MP3 file you last stopped playing (Resume play). During stop, the track/MP3 file number to be played is displayed.To cancel the resume play (to start play from the beginning of the first track/MP3 file), press the CD compartment or turn off the unit, the resume play is also canceled.

If there is no folder, “ROOT” appears in the display.If the playing time is more than 100 minutes, it appears “--:--” in the display.

VOLUME + (VOL + on the remote) unit have a tactile dot.

6

CFD-S03CP/S03CPLSECTION 3

DISASSEMBLY

Note: This set can be disassemble according to the following sequence.

3-1. CABINET (REAR) ASSY(Page 7)

3-2. CABINET (FRONT) ASSY,CABINET (UPPER) ASSY(Page 7)

SET

3-3. MAIN BOARD(Page 8)

3-9. TAPE MECHANISM BLOCK,BELT (1), BELT (2)(Page 11)

3-4. CD BLOCK ASSY(Page 8)

3-5. BD83S BOARD(Page 9)

3-7. PANEL BOARD(Page 10)

3-8. CD LID(Page 10)

3-6. OPTICAL PICK-UP(Page 9)

3-12. POWER BOARD(Page 12)

3-10. TC BOARD(Page 11)

3-11. KEY-1 BOARD,KEY-2 BOARD(Page 12)

7

CFD-S03CP/S03CPL

3-2. CABINET (FRONT) ASSY, CABINET (UPPER) ASSY

Note: Follow the disassembly procedure in the numerical order given.

3-1. CABINET (REAR) ASSY

1 two screws (+BV tapping (B2.6))

6 CN305 (3P)7 cabinet (rear) assy

4 three screws (+BV tapping (B2.6))

5

2 screw (+BV tapping B2.6)


handle

telescopic antenna



1 CN308 (4P)

5 flexible flat cable (4 core)(CN403)

7 flexible flat cable (14 core)(CN301)

6 CN304 (4P)

8 cabinet (front) assy

9 cabinet (upper) assy

4

8

CFD-S03CP/S03CPL

3-4. CD BLOCK ASSY

3-3. MAIN BOARD

5 two screws (+BV tapping B2.6)

7 two screws (+BV tapping B2.6)


8

0 MAIN board

1 CN306 (4P)

4 connector(S801)

3 flexible flat cable(20 core)(CN803)




3 CD chassis

4 CD cover

5 CD block assy

claw two claws


9

CFD-S03CP/S03CPL

3-6. OPTICAL PICK-UP

3-5. BD83S BOARD

3 Remove the two solders.

5 BD83S board

4 Remove the two solders.

2 screw (+BVTT 2 × 6)


claw

1 gear (A)

2 claw3

4 sled shaft

5 optical pick-up

10

CFD-S03CP/S03CPL

3-8. CD LID

3-7. PANEL BOARD

1 four screws (+P tapping (B2.6))

3 PANEL board

2 five screws (+P tapping (B2.6))

5 CD lid

6 CD spring

3

4

21

11

CFD-S03CP/S03CPL

3-10. TC BOARD

3-9. TAPE MECHANISM BLOCK, BELT (1), BELT (2)



3 tape mechanism block

4 two screws

5 motor bracket

6 belt (1)

7 belt (2)

1 screw (+P tapping (B2.6))

2 Remove the four solders.

3 TC board

12

CFD-S03CP/S03CPL

3-12. POWER BOARD

3-11. KEY-1 BOARD, KEY-2 BOARD


6 three screws (+BV tapping (B2.6))

3 two HOLDER boards

7 HOLDER board

4 KEY-2 board

8 KEY-1 board

5 button (volume)

9 button (FUNC)


2 screw (+BV tapping (B2.6))

4 POWER board

1 CN902 (2P)3 two screws (+BV tapping (B2.6))

13


MECHANICAL ADJUSTMENTSSECTION 5

ELECTRICAL ADJUSTMENTS

PRECAUTION1. Clean the following parts with a denatured-alcohol-moistened

swab :record/playback head pinch rollererase head rubber beltscapstan idlers

2. Demagnetize the record/playback head with a head demagnetizer.(Do not bring the head magnetizer close to the erase head.)

3. Do not use a magnetized screwdriver for the adjustments.4. The adjustments should be performed with the rated power

supply voltage (9V) unless otherwise noted.

Torque MeasurementMode Torque meter Meter reading

2.95 – 6.86 mN • mFWD CQ-102C (30 – 70 g • cm)

(0.42 – 0.97 oz • inch)

FWD0.15 – 0.53 mN • m

Back TensionCQ-102C (1.5 – 5.5 g • cm)

(0.021 – 0.076 oz • inch)

more than 5.88 mN • mFF CQ-201B (more than 60 g • cm)

(more than 0.83 oz • inch)

more than 5.88 mN • mREW CQ-201B (more than 60 g • cm)

(more than 0.83 oz • inch)

Tape Tension MeasurementMode Tension meter Meter reading

FWD CQ-403Amore than 100 g

(more than 3.53 oz)

TAPE SECTION 0 dB = 0.775 V

• Standard Output LevelOutput terminal HP OUT

load impedance 32 Ω

output signal level 0.25 V (–10 dB)

• Test TapeType Signal Used for

WS-48A 3 kHz, 0 dB tape speed adjustment

Tape Speed AdjustmentProcedure:Mode: playback

Adjust so that the value on the digital frequency counter is3,000 Hz.

Specification Value:Digital frequency counter

2,910 to 3,090 Hz

Adjust so that the frequency at the beginning and that at the end oftape winding are between 2,910 to 3,090 Hz.

Adjustment Location:

i jack (J321)

set

32 Ω

test tapeWS-48A(3 kHz, 0 dB)

digital frequencycounter

Tape speed adjustmentcontrol inside motor

14

CFD-S03CP/S03CPL

TUNER SECTION 0 dB = 1 µV

[AM (MW/LW)]Setting:Function: RADIO/BAND/AUTO PRESETBand: MW or LW

[FM]Setting:Function: RADIO/BAND/AUTO PRESETBAND button: FM

• Connecting Digital Voltmeter (FM, MW and LW)

• Repeat the procedures in each adjustment several times, and thetracking adjustments should be finally done by the trimmercapacitors.

• Remove FM antenna in FM adjustment.

+–

i jack (J321)

AM RF signal generator

30% amplitudemodulation by400 Hz signalOutput level: as low as possible

Put the loopantenna close to the set. level meter

set

32 Ω

set

i jack (J321)

FM RF signalgenerator

75 kHz frequencydeviation by 1 kHzsignalOutput level: as low as possible

level meter

32 Ω0.01 µF

MAIN boardTP ANT2 (JW231, 232)

+–

digital voltmeter

TP (VT)TP (GND)

100 kΩMAIN board

AM (MW/LW) IF ADJUSTMENT

Adjust for a maximum reading on level meter

T1 450 kHz

LW FREQUENCY COVERAGE ADJUSTMENT (AEP)

Adjustment Part Frequency Display Reading on Digital Voltmeter

L3 279 kHz 5.3 ± 0.5 V

Confirmation 153 kHz 0.6 ± 0.05 V

LW TRACKING ADJUSTMENT (AEP)


ANT1-2 162 kHz

CT5 261 kHz

MW FREQUENCY COVERAGE ADJUSTMENT (AEP)


Confirmation 531 kHz 0.9 ± 0.2 V

Confirmation 1,611 kHz 5.5 ± 0.5 V

MW FREQUENCY COVERAGE ADJUSTMENT

(EXCEPT CND, AEP, E92, MX)


L3 531 kHz 0.8 ± 0.05 V


MW FREQUENCY COVERAGE ADJUSTMENT (CND, E92, MX)


L3 530 kHz 0.8 ± 0.5 V


MW TRACKING ADJUSTMENT (EXCEPT CND, E92, MX)


ANT1-1 621 kHz

CT3 1,404 kHz

MW TRACKING ADJUSTMENT (CND, E92, MX)


ANT1-1 620 kHz

CT3 1,400 kHz

FM IF ADJUSTMENT

Adjust for a minimum reading on level meter

L6 10.7 MHz

FM FREQUENCY COVERAGE ADJUSTMENT


L2 108 MHz 3.0 ± 0.2 V

Confirmation 87.5 MHz 1.5 ± 0.5 V

FM TRACKING ADJUSTMENT


L1 87.5 MHz

CT1 108 MHz

Adjustment and Connecting Location:MAIN board (See page 15)

• AbbreviationCND : Canadian modelE92 : AC 120V area in E modelMX : Mexican model

Ver. 1.2

15

CFD-S03CP/S03CPL

Adjustment Location:

Test Point:

ANT1-2: LW TRACKINGADJUSTMENT

CT5: LW TRACKINGADJUSTMENT

CT1: FM TRACKINGADJUSTMENT

L1: FM TRACKINGADJUSTMENTT1: AM (MW/LW)

IF ADJUSTMENT

L6: FM IF ADJUSTMENT

L3: AM (MW/LW)FREQUENCY COVERAGEADJUSTMENT

L2: FM FREQUENCYCOVERAGEADJUSTMENT

– MAIN BOARD (Component Side) –

ANT1-1: MW TRACKINGADJUSTMENT

CT3: MW TRACKINGADJUSTMENT

IC1ANT1

C31

C33

C70

R39

C16

C34

R15

C69

R13

C55

R23

R26

C51

C45

R7

C21

C4

R11

C9

R28

D6

R20

R2

R18

R1

C1

C2

C6

C54C32 E92,MX

MODEL

C40

C41

C22

R35

C42

R29

C20

R9

IC1

C68

R3

C53

R12

C7

R38

C38

C46

R37

C60

R5

C63

R34

R36

C13

R25

Q35

R31

C14

C10

C11

C12

R6

R30

C35

C37C2

7

R19

C26

R16 R

17

C24

C62

Q32

C15

Q33C61

R32

C64

C25C28

R10

R22

C3

R21

R4

C5

R14

R27

C67

R41

C72

JW207

C23

JW2

JW188

D2 L2

D1

JW18

7

X1

C29

JW22

4

C39

C18

L3 C19

JW217

JW20

8

C17

T1

JW19

1

CT5

C30

CF3

CF2

JW218

CT1

D3

CT3

L1

JW232

JW231

D5

JW22

3

L6

JW209

JW22

0

JW226

D4

JW219

TP (VT) TP (GND)

TP ANT2

– MAIN BOARD (Conductor Side) –

16

CFD-S03CP/S03CPL

CD SECTION

CD section adjustments are done automatically in this set.In case of operation check, confirm that focus bias.

FOCUS BIAS CHECK1. Connect the oscilloscope between IC201 pin u; and pin th (or

TP (RFAC0) and TP (VC)).2. Insert the disc (PATD-012 (Tr 15)). (Part No. : 4-225-203-01)3. Press the N X (CD) button.4. Confirm that the oscilloscope waveform is as shown in the figure

below. (eye pattern)A good eye pattern means that the diamond shape ( ) in thecenter of the waveform can be clearly distinguished.

• RF signal reference waveform (eye pattern)

When observing the eye pattern, set the oscilloscope for AC rangeand raise vertical sensitivity.

Test Point:

B9

RFACI

VC FEI

TEI

RFACO

APC

R257

C258

C260

C261R258

C304

C208

R26

5

R266

R267

C264

C265R278

C214

R270

C221

C292

C291R292 R

291

IC201

C217C218

1

3031 60

61

90

100 91

C224

03

C256

C251

C252

C254C253

R254

R25

5

R252

R25

3

CN30

1

C213 C222

03

C301

C303

C273

R26

8

C230

R250

1-868-067- (11)11

TP (RFAC0)TP (VC)

– BD83S BOARD (Conductor Side) –

RF level :1.1 Vp-p

VOLT/DIV : 50 mV (10 : 1 probe in use)TIME/DIV : 500 nS

+0.3–0.2

17 17CFD-S03CP/S03CPL

CFD-S03CP/S03CPL

6-1. BLOCK DIAGRAM — CD SECTION —

SECTION 6DIAGRAMS

A

B

C

F

E

D

A

B

C

D

LD

PD

VR

F

T+T–

F+F–

SL+SL–

SP+SP–

E

VC

LD

PD

LD POWERCONTROLLER

Q321 APC

A

B

C

D

LD

PD

F

E

VC

51

50

56

66

59

60

67

57

58

51314

TRACKINGCOIL

DRIVE

6

20

7

FOCUSCOIL

DRIVE

CH1INR

4CH1INF

CH2INFCH2INR

23CH3INF

22CH3INR

SLEDMOTORDRIVE

24SPINDLEMOTORDRIVE

CH4IN

VREF

OPIN+

OPOUT

MUTE

CH1OUTRCH1OUTF

CH2OUTFCH2OUTR

CH3OUTFCH3OUTR

CH4OUTFCH4OUTR

1211

1718

1615

VC

TRACKINGCOIL

FOCUSCOIL

OPTICAL PICK-UPBLOCK

(KSS-213C)

M

M

M402SLED

MOTOR

M401SPINDLEMOTOR

SLED/SPINDLEMOTOR DRIVER,

TRACKING/FOCUSCOIL DRIVER

IC402

S201(LIMIT)

XLAT

XTAC

NAC

K-M

P3IR

EQ-M

P3RE

Q-M

P3

XLAT

-MP3

CLK2

DATA

2

DATA

CLOK

SENS

SCOR

XRST

XTAO

XTAI

AOUT1

AOUT2A

TRDR

TFDR

12 90 13 15 891671014 11 20 109 10826 8

112

117

RF AMP,SYSTEM SERVO PROCESSOR,DIGITAL SIGNAL PROCESSOR

IC201

37

18

31 30 29 43 4

45

28 26

X20116.93MHz

VDD (1.8V)CD3.3V

VDD (3.3V)

O-CD

-CLK

O-CD

-CM

D

I-CD-

SENS

I-CD-

SCOR

I-ACK

-MP3

27

I-RQ-

MP3

12

O-RQ

-MP3

11

O-ST

BY-M

P3

10

O-XL

AT-M

P3

6

O-CL

K-M

P3

5

O-DA

TA-M

P3

7

I-DAT

A-M

P3

CD-X

RST

LID-OPEN

BAT-

CHK-

H

1

O-PO

WER

SYSTEM CONTROLLERIC801 (1/2)

+3.3VREC/PBPOWER

CONTROLQ957-959,D957

RIPPLEFILTERQ304

AUDIO+6VREG

Q955,D953

+3.3V REGIC804,Q802

+1.8V REG.IC202

POWERSWITCH

Q952,953

POWERSWITCH

Q951

CD 3.3V

SW2 PUSH

OPEN/CLOSE

3.3V AC-HI

AC-CHK

9V (SW)

R-VT

6V(TAPE)

CD 6V

RADIO +B

D901 – 904RECT

F902

Q801

T901POWER

TRANSFORMERJ901

AC IN

Signal path : CD

DSP DACSYNCHRONOUSCIRCUIT

I/F

CLOCKGENERATOR

26

8

I-CD-

XLAT

O-CD

-XTA

CN

VCVC

CD_IN_R

CD_IN_ L

DRY BATTERYSIZE "D"

(IEC DESIGNATION R20)6PCS, 9V

DIGITALSERVO

CONTROL

PRI-SERVOAMP

38

V-CH

ECK

44 43

FFDR

FRDR

SFDR

SRDR

MDP

SSTB

45 46 41 42 38 39

45

36

REG-

CHK

23

I-CD-

CTL

D951

D952D324

BATTVDD

U-COM(VDD)

2

27

(Page 18)

1818CFD-S03CP/S03CPL

CFD-S03CP/S03CPL

6-2. BLOCK DIAGRAM — MAIN SECTION —

5

21 22 16

4

L-CH

R-CH

HRP301RECORD/PLAYBACK

HEAD

HE301ERASE HEAD

DET

ALC 2

RADIO L

18

15

L.LO

R.LO

LINE

TAPE

R-CH

TU_IN_R

TU_I

N_L

TAPE

CD

LOGIC

5

CLK

4

DATA

POWER AMPIC303

D322

R-CH

SP101SPEAKER

(L-CH)

SP201SPEAKER

(R-CH)

J321

REF

L.LINL.RO

REC

L.RA

D

R.RA

D

T301

Q302

REC BIAS OSCQ301

TAPE

CD-O

N

57

VOL-

CLK

VOL-

DATA

62–59

LIQUID CRYSTALDISPLAY PANEL

LCD401

FREQUENCYEXCHANGE

SWITCH

SYSTEM CONTROLLERIC801 (2/2)

3455 33

M-B

ASS

17

COM

1|

COM

4

S1 |S2

9

EEPROMIC802

SCL

SAD

42

WAK

E-UP

48

I-SUF

FIX

Q805,D801,802

Q806

3.3V

AEP,AUS,AR,KR,TW MODEL

I-KEY

2

41

I-KEY

1

40

I-KEY

0

39

Signal path : FM : AM : TAPE PLAY : TAPE REC : CD

R-ch is omitted due to same as L-ch.

AbbreviationAUS : Australian modelAR : Argentina modelKR : Korea modelTW : Taiwan model

REC/PBPRE AMP

IC301

6 2

MEGABASS

SWITCHQ122

20

6

14R.LIN

8R.IN

L.IN

9R.RO

i

A-M

UTE

3

MUTEQ124

LEVELDETECT

D323

TAPE

-PLA

Y

24

M

TAPE PLAYDETECT

Q808

24

TAPE

REC

25

ISS1

49

-1 -2S301(REC/PB)

REC

PB

9V (SW)

I-RMC

KEY0

KEY2KEY1

SW1(TAPE PLAY)

M901CAPSTAN/REEL

MOTOR

17

CD_IN_R

CD_IN_L

65

4746

+B6V (TAPE)

TU_IN_R

U-COM(VDD)

9V (SW)

A

KEY NETWORK

D406OPR/BATT

L-IN L-OUT

IC302ELECTRONIC VOLUME

8 7

VOL AMP

54

RESE

T

2

FM/A

M S

HIFT

O-TU

-DAT

AI-T

U-CO

UNT

O-TU

-CLK

O-TU

-CE

93X0

92

X1X802

4.19MHz

RESETIC805

3.3V

1

2

REMOTECONTROLRECEIVER

IC401

19

3

DI

X IN

X OU

T CL

LP-O

UTAMOSC

AMMIX

FMMIX

FMOSC

AM RF-IN

AM OSC

REG

BO1

FMRF-IN

FMIF-IN

AMIF-IN

X175kHz

20 19 16 17

CE

15

DO

18

21 20 1922

23 221312

28

LP-IN

27

PD

26

1

31

2

5 7

8

11

36

29BO230

3234

T1

L6

CF3

L2L1 CT1

RADIO 5VRADIO 5V

D1 D2

CT3

CT5

D3

ANT1-1,CT3MW TRACKING

ANT1-2,CT5LW TRACKING

CT1,L1FM

TRACKING

L2FM

FREQUENCYCOVERAGE

L3MW/LW

FREQUENCYCOVERAGE

L6FMIF

T1AWIF

ANT2FM

TELESCOPICANTENNA

AMDET

FMDET

AFBUFFER

FMMPX

R-OUTL-OUT

RADIO 5V

FM-DET VCC

FM/MW/LW FRONT-END,IF AMP, DET, FM MPX

IC1

L3

JC4

AEP MODEL

AEP MODEL

EXCEPTAEP MODELEXCEPT

AEPMODEL

-1

-2

Q33

JC3

RADIO 5V

R-VT(VT)

CF2

RADIO 5V

RADIO 5V

ANT1MW/LW

FERRITE-RODANTENNA AM

MIX-OUT

FMMIX-OUT

FMRF-OUT FM OSC

DET-OUT MPX-IN

3

S401–407S411,413–417S421–424

Q303

ISS2

50

D461AC-HI

RADIO 5V RADIO+B

97–94,89–67,64,63

6,33

Q31Q32Q35

(Page 17)

Ver. 1.1


CFD-S03CP/S03CPL

6-3. CIRCUIT BOARDS LOCATION • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• W : indicates side identified with part number.• f : internal component.• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

• A : B+ Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.– BD83S Board –

no mark : CD PLAY– MAIN (1/3) Board –

no mark : FM( ) : AM– MAIN (2/3), (3/3) and Other Boards –

no mark : FM( ) : PB< > : REC[ ] : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal productiontolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

• Circled numbers refer to waveforms.• Signal path.

F : FMf : AME : PBa : RECJ : CD PLAY

• AbbreviationCND : Canadian model.CET : East European & Russian model.E41 : AC 230V area in E model.E92 : AC 120V area in E model.AUS : Australian model.KR : Korea modelMX : Mexican model.SP : Singapore model.IT : Italian model.AR : Argentina model.TH : Thai model.TW : Taiwan model.

C

B

These are omitted.

E

Q

B

These are omitted.

C

Q

Q

E

B C E

Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.

• Waveforms

— BD83S Board — (CD PLAY)

— MAIN Board —

• AbbreviationCND : Canadian model.CET : East European & Russian model.E41 : AC 230V area in E model.E92 : AC 120V area in E model.AUS : Australian model.KR : Korea modelMX : Mexican model.SP : Singapore model.IT : Italian model.AR : Argentina model.TH : Thai model.TW : Taiwan model.

HEADPHONE board

PANEL board

KEY-1 board

KEY-2 board

MAIN board

BATTERY-1 board

BATTERY-2 board

TC board

BD83S board

POWER board

1.1 Vp-p

Approx. 150 mVp-p

5 IC201 u; (RFACO)

500 mV/div, 0.5 µsec/div

1.7 V

Approx. 1 Vp-p

1.7 V

4 IC201 tg (FEO)

100 mV/div, 5 msec/div

3 IC201 td (TEO)

1 V/div, 5 msec/div1 V/div, 10 µsec/div

1 V/div, 200 nsec/div

3.2 Vp-p

2 IC201 5 (BCK)

0.47 µsec

3.2 Vp-p

1 IC201 1 (LRCK)

22.6 µsec

3.3 Vp-p

16.95 MHz

6 IC201 <z/, (XTAO)


+0.3–0.2

2.2 Vp-p

1 IC1 w; (X OUT)

1 V/div, 5 µsec/div

75 kHz

3.4 Vp-p

4.13 MHz (AM)4.17 MHz (EXCEPT AM)

2 IC801 os (X1)


— TC Board — (REC)

18.2 µsec

3.5 Vp-p

1 Q301 C


18.2 µsec

35 Vp-p

2 HRP301 (YEL)


Ver. 1.2

Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.

Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepiéce portant le numérospécifié.

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)


CFD-S03CP/S03CPL

6-4. PRINTED WIRING BOARD — BD83S SECTION — • Refer to page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

MM

M

R25

6

C257

R260

C206

C205

C322

R32

3

R322R321

R324

C223

C321

C268

C267

R271

R203

C226

R20

1

C227

C110 C1

08

C102

C203

C204

C101

IC202

C274

C202

R20

7

C215

R202

C201

R423

R421

C424

C276

C210

Q32

1

CB

1 2 3

E

C207

C266

C275

C323

C277C4

06

R40

1

C401

C219

R276

C271 C272

C104

C105

C107

C109

C232

C220

S201(LIMIT)

X201

B7

B8

B9

B10

RFACI

VC FEI

TEI

RFACO

APC

M401(SPINDLE)

R257

C258

C260

C261R258

C304

C208

R101

R26

5

R266

R267

C264

C265R278

C111

C214

R270

C221

C292

C291R292 R

291

IC201

C217C218

1

3031 60

61

90

100 91

C224

R45

1

R102

R103

R10

4R

105

R107 R10

8

R109

R11

0

R11

1

C451

IC40

2

C256

C251

C252

C254C253

R254

R25

5

R252

R25

3

CN30

1

OPTICALPICK-UPBLOCK

(KSS-213C)

C213 C222

C405 R11

3

C404

R452

C112

R27

5R

277

C103

R11

2

C301

C303

C273

R26

8

C113

CN102

C230

R250

R28

0

M402(SLED)

MAIN BOARDCN805

A

1-868-067- (11)11

1-868-067- (11)11

(Page 22)


CFD-S03CP/S03CPL

6-5. SCHEMATIC DIAGRAM — BD83S SECTION — • Refer to page 19 for Waveforms. • Refer to page 32 for IC Block Diagram. • Refer to page 34 for IC Pin Description of IC201.

IC B/D

R324

R101

R451

R102

R103

R104

R105

R107

R108

R109

R110

R255

R253

R25

8

R254

R252

R26

8

R322

R321

R275

IC201

C205

C208

C213

C217

C219

C221

C251C252

C253C254

C273

C274

C291

C292

C301

C405 C406

R267

R266

C265 R265

C264

C261

R250

C260

C258

C230

C257

R256

C256

C206

TP3

TP4

C207

C232

TP1

R271

C223

R292

R291 C276

C277

C218

C222

C210

R207

R202

C202

C203 C204

C226

R113

R112

C113

C112

C110

C108

C102

C101

C103

C105

C111

C104

C109

C107

R111

R401

C401

R277

R276 C272 C271

R278

C227

C224C220

R280

C404

TP2

C451

C424

R452

R421

R423

C323

C322

C321

R323

CN301

CN102

R201

C201

C303 C304

Q321

M402

M401

S201

R260 R257

IC402

IC202

C267C266

R270

X201

C268

C275C215

C214

R203

(Page 24)


CFD-S03CP/S03CPL

6-6. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

MM

+

+

+

+

+

+

+

C836

C31

C33

R89

8

JC4

JC3

JC1

C70

R39

C16

R82

7

R33

7

R82

6

C217

R897

C804

C957

C961

R329

R33

0

C232

C817

R899JC807

D951

Q951

IC802

R844

C330

R95

3

R955

R95

4 R95

1

R96

3

R96

2

R96

1

Q959

Q958

R958

R96

5

C358

R957

R95

6

R33

3

R33

6

R487

R47

8

JC10

3

R48

1

C819R472

R80

4

C811

R868

C813

R80

1

C815

R473

C820

R48

6

R238

C806

R48

2

R26

1

R16

1

R492

IC805

13

54

R32

8

R327

C227

C354

R244

R14

4

C825

C210

C110

R247

C127

C356

C106

R23

5R

234

R885

R236

C225

C129

R134

R135R136

R239

R139

C206

Q222

R48

3

Q122

Q124

B

B C E

BC

ECE

BCE

R140

R138

R240

D323

R32

3

C324

R32

4

R24

5

R145

R31

6

R14

3

Q22

4

R241

C108

C208

R242

R142

R24

3

R141

R886

R869

R147

C34

R870

C803

R88

4

R15

R818

R16

2

D46

2

R46

3 D461

R462R461

R82

9

R465

R467

R464

R48

4

C457

R48

0

JC804

Q806R

820

Q805

AEP,AUS,KR,AR,TWMODEL

UK,E41,CET,IT,SP,THMODEL

AEP,AUS,KR,AR,TWMODEL

CND,AEP,E92,AUS,MX,KR,AR,TW MODEL

R89

3

R816

FB831

R824

R823 R822 R821

R825

R89

6

R891

R89

2R

811

R810

R80

9

R889

R88

8

C69

D802

R88

7

R47

5

R477

C807

R471

R48

8

R831

C816

R828

R805

R814

R451

R453

R45

2

C458

R813

C455

C456

C453

C451

C454

JC10

2

C452

Q451BCE

BCE

Q452

JC10

1

C814

R474

R819

R83

0 R80

3

R262

R876

R878

R875

Q801

R83

5

R83

6

R83

7

R83

8

R83

9

R84

0

R84

1

R84

2

R84

3

C822

C823

R81

7

R845

R846

R466

R87

9

R847

R880

R13

R848

R85

0

R85

1

R85

2

R85

3 R854

R855

R85

6

R85

7

R85

8

R85

9

R86

0

R86

1

R86

4

R86

3

R86

2

R86

7

R86

5

R812

C55

R23

R26

C51

C45

R7

C21

C4

R11

C9

R28

D6

C52

D95

7

R877 R874

R88

3

R20

R33

1

R2

R18

R47

9

C821

R84

9

R815

3

5 4

R1

R47

6

C1

R24

C2

C6

C117

Q808

B C E

R86

6

C54C32

CND,E92,MXMODEL

C40

C41

C22

R35

C42

R29

C20

R9

IC1

C68

R3

C53

R12

C7

R38

R872

R87

1

R87

3

C38

R802

C46

R37

C36

Q31

C60

R5

C63

FFC802 1

14

14

R335

R33

8

D953C952

C951

R89

4

C350

C349

R33

2

R34

R96

4

R95

9

Q957

R95

2

R36

Q304

C13

Q953

B

B

C

C

E

B C E

B C E

BCE

B C E

E

R96

0

IC302

R32

1

FB832

R325

R25

R491

JC2

AEP MODEL

-2

-1

EXCEPT AEPMODEL

R49

3

R490

Q35

R31

C14

C10

C11

C12

R6

R30

C35

C37C2

7

R19

C26

R16 R

17

C24

R326C62

Q32

C15

Q33C61

R32

C64

C25C28

R10

R22

C3

R21

R4

C5

R14

R27

C67

C818

R41

C72

C132

CN806

D80

1

JW23

0

JW16

3

JW247

JW23

3

C311

JW13

2

JW19

4

JW12

9

JW170

JW10

5

JW16

9

JW12

6

JW14

2

JW14

9

C213

C461

JW10

7

D952

JW22

9

JW17

4

JW14

5

JW16

8

JW19

0

JW13

1

JW17

7

JW14

3

JW15

1

JW167

JW13

7

C357

C959

JW17

8

JW14

1

JW10

2

JW14

0

C956

JW17

1

JW246

JW200 X802

JW24

2

JW241

JW24

9

JW254

JW25

6

JW23

4

JW11

7

JW146

JW116

JW10

4

C355

C229

C125

C115

C215

C331

C323

IC303

C212

C119

C219

C112C322

C231

C131

16 4 3

7 9 10 12

C130

C230

JW24

5

JW12

8

JW130

JW207

C23

JW120

JW23

5

C805 JW21

6

JW21

2

Q80

2

BE

C

JW18

3

JW24

8

JW25

5

JW23

7

JW21

5

JW23

9

JW22

2

CN803

JW108

JW24

4

JW20

1

JW23

8

JW22

1

JW23

6

JW21

3

JW22

8JW

185

JW24

0

JW18

9

JW21

4

JW11

0

JW19

5

JW203

JW21

0

JW20

6

JW118

JW18

2

JW19

7

JW20

2

JW186

JW18

4

JW19

8

C808

D32

2

JW199

JW17

6

JW15

0

JW14

7

CN804

JW15

2

L804

JW15

6

JW19

6

JW15

7

JW16

1

JW16

2

JW16

0

JW179

JW12

4

JW15

5

JW18

1

JW16

6

JW16

5

JW16

4JW

106

JW22

7

JW17

2

JW20

5

JW15

9

JW15

4

JW188

D2 L2

D1

JW18

7

X1

C29

JW22

4

C39

JW257

JW15

3

JW15

8

C261

C161

C18

C262

C162

JW19

3

JW21

1

JW22

5

JW17

5

JW14

4

JW13

8

JW119

JW13

9

CN805

CN304

L3

C43

C19

JW217

JW20

8

C17

T1

JW19

1

CT5

C30

CF3 CF

2

C113

JW19

2

CN305

1 3

JW20

4

JW18

0

JW218

JW14

8

JW13

6

JW135

C325Q955

JW13

3

Q952

JW12

5

C953

JW25

0

CN306

1 4

JW10

3

C353

ANT1

ANT1MW/LW

FERRITE BARANTENNA

D324

JW127

JW13

4

C326

JW12

1

JW10

1

CT1

D3

CT3

L1

JW232

JW231

D5

JW22

3

L6

JW209

JW22

0

JW226

AEP MODEL

AEP MODEL

D4

JW219

L803

PANEL BOARDFFC402

C

BD83S BOARDCN102

A

PANEL BOARDFFC401

D

TC BOARDCN301

B

IC801

3031

50

51

80

1

100

81

HP BOARDCN307

F

POWER BOARDCN901

E

ANT2FM TERESCOPIC

ANTENNA

SW2

1-869-160- (11)11

Z/PUSHOPEN/CLOSE

SW1(LEAF SW)

M801(CAPSTAN/REEL MOTOR)

1

1

2

3IC804

IC806TYPE B

TYPE A

D461 H-5D462 H-5D801 G-7D802 G-7D951 C-8D952 C-9D953 C-8D957 C-10

Ref. No. Location

D1 C-4D2 B-4D3 D-3D4 B-5D5 B-5D6 C-6D322 E-10D323 C-12D324 C-7

• Semiconductor LocationRef. No. Location

IC1 C-5IC302 E-9IC303 D-12IC801 G-10IC802 G-3IC804 F-5IC805 H-4IC806 F-4

Ref. No. Location Ref. No. Location

Q31 E-3Q32 E-3Q33 C-3Q35 D-3Q122 D-11Q124 E-11Q222 D-11Q224 C-11Q304 C-9

Ref. No. Location Ref. No. Location

Q451 H-12Q452 G-11Q801 G-6Q802 F-5Q805 F-7Q806 G-6Q808 H-6Q951 C-8Q952 B-9

Q953 C-9Q955 B-7Q957 C-11Q958 C-10Q959 D-10

(Page 20)

(Page 30) (Page 26)

(Page 26)

(Page 28) (Page 28)

Ver. 1.4

Refer to NOTE FOR REPLACEMENT OF THEIC804 AND IC806 on page 4 for type A and B.


CFD-S03CP/S03CPL

6-7. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 19 for Waveforms. • Refer to page 32 for IC Block Diagram.

IC B/D

C2

C7

C19

R5

R15

R25

R28

D4

D5

R39

R29

R41

C30

C63

C62

C61

C68

C64

C60

C53

C52

C51

C15 C69C13

C11 C12

C54

C9

C55

R26

C21

C29

C1

D1 R1 CT1 C3 C67

C4 R2

R3C5

C6

D2

R7

R4

R11

R14C16

R9

R13

C45

R12

C17 C46C18

C20

C39

R27

C42C41C43

R24

C70

C22

C25

C23

C24

C27

C28

R10

C32

C35

C36 C3

7

R16

R18 R19 R20 R21

R22

C38

R23

R35

R30

R37

R38

R36

R34

CT5

Q31

R32

R31

JC3JC2

JC1

JC4

ANT2

C33

C31

L6

CF2

CF3

L2L1Q33

R6

D3

D6

C40

C34

R17

C72

C26

X1

T1

L3

C14

C10

CT3

Q35

ANT1

IC1

Q32

(CND,E92,MX)(EXCEPT CND,E92,MX)

(CND,E92,MX)(EXCEPT CND,E92,MX)

CND,E92,MX MODEL

(Page 24)

Ver. 1.2


CFD-S03CP/S03CPL

6-8. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 19 for Waveforms. • Refer to page 37 for IC Pin Description of IC801.

TYPE B

TYPE A

UK,E41,CET,IT,SP,TH MODEL

AEP,AUS,KR,AR,TW MODEL

(AEP,AUS,KR,TW)(CND,E92,MX,AR)

(AEP,AR)(AUS,KR,TW)

XC6202P332FRIC806

Q802

C161

C162

C261

C262

FB831

Q805

R16

2

R26

2

R802

R80

5 R80

9

R81

0

R81

1

R81

2

R81

3

R81

4

R81

5

R81

6

R817

R818

R819

R820

R821R822R823

R824

R825

R828

R829

R830

R83

1

R83

5

R83

6

R83

7

R83

8

R83

9

R84

0

R84

1

R84

2

R84

3

R84

4

R84

5

R84

6

R84

7

R84

8

R84

9

R85

0

R85

1

R85

2

R85

3

R85

4

R856

R857

R858

R859

R860

R861

R862

R863

R864

R865

R866

R867

R868

R88

3

R88

4

R89

1R

892

R80

4

R855

R451R

452

R463

R477

R480

R481

R482

D461

Q451

Q452

R49

0

R49

1R

492

R16

1

R26

1

L803

C821

C822

C823

FFC802

C806

C825

C458

C456

C455

C457 C451

C818C807

C820

C814

CN806

SW2

CN803

CN804

R48

8

R486

R487

C454 C453

C805

C804

C803

CN807

R801

C811

C813

R479

R476R478

L804

R886

R885

R493

R89

3

R89

4

R89

6

R483

R869

R870

R48

4

D80

2

D80

1

R461

R462

C461R464

R465

R466

R467

CN805

R471

R472

C808

R803

JC804

Q801

Q806

R826

R898

R474

R473

R475

C816

R887

C819

C815

R453

IC805

R88

9R

888

FB832

IC801

IC802

D462

R827

X802

C452

R871

R872R873

R874R875

R876

R877R878R879

R880

IC804

IC806

(Page 21)

(Page 23)

(Page 27)

(Page 25)

(Page 29)

(Page 29)

Ver. 1.4



CFD-S03CP/S03CPL

6-9. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 32 for IC Block Diagrams.

IC B/D

IC B/D

R952

R951

R239

R95

5

R96

0

R956

R957

R953

R331

R332

R323

R138

R24

3

D95

3

D95

7

R335

R33

6R

337

R33

8

R96

1

R96

2

R96

3

R96

4

C112

C113

C125

C212

C213

C225

C230

C311

C323

C325

C953

C353

R32

1

R32

8

R32

9

R33

0

R324

Q95

3

CN304

CN306

C115

C215

J321

CN305

C349

C330

C117

C229

C217

C350

C206

C106

C129

C127

C132

C227

C232

C951

C952

C354

C356

C110

C324

CN307

R134

R135 R136

R242

C219

R244

C322C231 C210

C208

R241

R247

R238

R236R235

R234

R327

R147

R140C130

C108

R141

R142R144

C119

C355

R240

R14

3

R139

C326

R325

R326

C961

C957

R959 R958

C357

R95

4

JC807Q808

R245 R145

Q122

Q222

Q124

Q224

CN308

SP101

SP201

R146R148

R246R248

Q955

Q304

C131

SW1

IC302

D323

IC303

D322

D324Q958

C959

Q959

Q952

Q951

D951

D952

R316

C817

R897

R899

M901

R965

C358

R333

Q957

C956

C331

C216 C116

(Page 24)

(Page 31)


CFD-S03CP/S03CPL

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13 14

iC116

C216

R14

6 R14

8

R24

6

R24

8

CN307CN308

JW321

JW322

Q30

3

R31

2

C318

R21

1

JC306

JC30

7

R20

4

C307

C103

C312

FB20

5

FB20

4

FB20

3

FB20

2

FB207

FB20

1

R314

R305

FB20

6

JC30

8

R30

3R

201

R10

5

Q30

2

C104

R31

1

C205

C306

R210

R20

3

R310

R103

C308

R106

R202

R302

Q301

R104

R30

6

R21

2

C309

C201

C207

R30

8

R20

5

R30

4

R30

1R

309

R102

R101

R20

6

C107

R11

1

C203

C101

R110

C204

R30

7C305

C310

R11

2

R315

C105

JC305

R108

R20

9

R20

8

JC30

2

JC30

3

R109

R107

R20

7

C303

JW30

2

JW30

1

C302

CN301 JW303

T301

C202

JW304

C102

S301

C304

C301

IC301

MAIN BOARDFFC802

B

1-869-165- (11)11

S301(REC/PB)

PB

REC

WH

T

RED

YEL

BLK

BLK

WH

T

RED

YEL

(L-CH) (R-CH)

HRP300RECORD/PLAYBACK

HEAD

HE301ERASEHEAD

5

43

2

671

J321

SP201SPEAKER

(R-CH)

SP101SPEAKER

(L-CH)

1-869-164-

(11)11

MAIN BOARDCN306F

6-10. PRINTED WIRING BOARDS — TC SECTION — • Refer to page 19 for Circuit Boards Location. : Uses unleaded solder.

(Page 22)

(Page 22)


CFD-S03CP/S03CPL

6-11. SCHEMATIC DIAGRAM — TC SECTION — • Refer to page 19 for Waveforms. • Refer to page 33 for IC Block Diagram.

IC B/D

FFC802

C302

R204

R104R109

R101

R201

R212

R112

R107

R207

IC301

C105

C104

C101

C107

R110

C301 R301

C309

R210 C205

C207

C201

R106

R206

C312

C307R307

C304

R308

R312R306

R315R314R305

R203R202 R208C202

R211

R309

R205

R303

R302

R304

C102 R102 R108 R103

C103

C204 C203

R209

R111

C303

HRP301

HE301

FB207 JC302

JC303

FB206

FB205

FB204

FB203

FB202

FB201

T301

S301

R105

JC305

JC306

Q301

C310 C308

Q302 Q303

R310 R311

CN301

C318C305

C306 JC308 JC307

(AEP,UK,CET,KR,IT)(CND,E41,E92,AUS,MX,SP,AR,TH,TW)

(Page 24)

Ver. 1.2


CFD-S03CP/S03CPL

6-12. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

2 3 4 5 6 7 8 9 10 11 12 13 14

R406

FFC401

R43

2

C401

R43

0

R404R403

R407

R416 R408R409R417 R415

R414

R413

R41

2R

411

R418

R419

R43

1

R402

R40

5

R401FFC4021

133

201 20 D406

JW40

1

IC401

123

IC401

S401

S404

S402S405

S416

S416

S415

S407

S407

S403S413

S414

S417

S417

CN403

13

24

S406

R421

R423

R422

FFC412 FFC411S411

S421S422

1 3

42

R424

CN421

S423S424

1-869-162- (11)11

1-869-161- (11)11

TAPE

CDRADIO/BAND/AUTO PRESET

1-849-163- (11)11

VOLUME

MAIN BOARDCN803

C

MAIN BOARDCN804

D

LCD401LIQUID CRYSTAL DISPLAY UNIT

x BX

S413./PRESET

S414>/PRESET

S403MEGA BASS

S406REPEAT

S404DISPLAY/

ENTER

S401z/POWER

SLEEPMODE

D406OPR/BATT

/TUNE

S415 /

TUNE

(EXCEPT AEP,UK,CET,IT)

(AEP,UK,CET,IT)z/OPERATE

(Page 22) (Page 22)

Ver. 1.1


CFD-S03CP/S03CPL

6-13. SCHEMATIC DIAGRAM — PANEL SECTION —

D406

IC401

R401 R402 R403 R404 R405 R406 R407 R408 R409

R411 R412 R413 R414 R415 R416 R417 R418 R419

R422 R423

R424

FFC402 FFC401

C401

R432 R431

R430

CN403 FFC411

FFC412 CN421

S417

S406 S407

S416

S405

S415

S404

S414S413

S403S402S401

LCD401

FFC422

S424S423

S422S421S411

R421

RADIO/BAND/AUTO PRESET

(EXCEPT AEP,UK,CET,IT)

(AEP,UK,CET,IT)

OPERATE

(Page 24) (Page 24)

Ver. 1.1


CFD-S03CP/S03CPL

6-14. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 19 for Circuit Boards Location. : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

2 3 4 5 6 7 8 9 10 11 12 13 14

–

+

+

–

–

+

C901

C903

C904

J901

CN90

1

JW908

D903

F902FH901 FH902

D901

D902

C902 D904

C906JW

907

CN90

2

JW90

4

JW90

5

CN903

JW90

0

JW90

1

JW90

2

JW90

3

1-869-167- (11)11

1-869-168- (11)11

REDGRY

MAIN BOARDCN305E

DRY BATTERYSIZE "D"

(IEC DESIGNATION R20)6pcs, 9V

1-869-166-

(11)11AC IN-

T901

(Page 22)


CFD-S03CP/S03CPL

C906

CN903

C901

FH902FH901

F902

T901

D901

D902

C902

C903

D903

D904

C904

J901

CN901

CN902

6-15. SCHEMATIC DIAGRAM — POWER SUPPLY SECTION —

(Page 25)


CFD-S03CP/S03CPL

• IC BLOCK DIAGRAMS

IC1 LV23003VA (MAIN Board (1/3))

1AM RF-IN

3FM-MIX

2REG

6VCC1

4GND1

AMRF

AMMIX

AMDET

AMIF

FMDET

FMIF

SD

FF

VCO

FF

FF

ST

TRIG

STSW

FMMIX FM

OSC

AMOSC

OSCBUFFER

FMS-METER

DECODER

PHASECOMPARATOR

MUTE

PROGRAMMABLEDIVIDER

REFERENCEDIVIDER

UNLOCKDETECTOR

SWALLOWCOUNTER

POWER ONRESET

DATA SHIFTREGISTER

LATCH

PHASEDETECTOECHARGEPUMP

UNIVERSALCOUNTER

5AM MIX-OUT

7AM IF-IN

8FM IF-IN

9P-DET

10P-COMP11FM-DET

12L-OUT13R-OUT

14VSS

FMRF

36 FM RF-IN

35 GND2

34 FM RF-OUT

33 VCC2

30 BO229 BO1

32 FM OSC

31 AM OSC

28 LP-OUT27 LP-IN

23 DET-OUT

15CE16DI17CL18DO

22 MPX-IN

19 X IN20 X OUT

21 VDD

26 PD25 AGC

24 AM LOW CUT

LOW-PASSFILTER

AGC

IFBUFFER

PIROTDET

CCBI/F

IC402 BA5947FM-E2 (BD83S Board)

IC303 TA8227P (MAIN Board (3/3))

6

L-IN

L-NF

PREG

ND

L-BS

L-OU

T

CTU

R-IN

R-NF

RIPP

LE

R-BS

R-OU

T

VCC

5 4 3 2 1

7 8 9 10 11 12

1

LEVEL SHIFT

MUTING D

1516

+ –

+–

DD

1718

D

1920

VREF

2122232425262728

PREV

CC

OPOU

T

OUTV

REF

CH4C

APA

CH4I

N

CH3F

IN

CH3R

IN

GND

MUT

E

POW

VCC

CH3O

UTF

CH3O

UTR

CH4O

UTF

CH4O

UTR

OPIN

–

2

OPIN

+

INTERFACE

1413

D

1211

D

109876

CH2F

IN

CH2R

IN

GND

54

CH1F

IN

CH1R

IN

VREF

IN

POW

VCC

CH2O

UTR

CH2O

UTF

CH1O

UTR

CH1O

UTF

INTERFACE

D D

3

SW

INTERFACE

33

CFD-S03CP/S03CPL

IC302 PT2257-S (MAIN Board (3/3))

VR 2

VR 1

R-IN R-OUT GND DATA

L-IN L-OUT VDD CLK7

2 3 4

8

1

REF AMP

VOL AMP 2

VOL AMP 1

6

LOGICCONTROL

5

VREF

1

2

3

6

9

10

11

12

8

7

4

5

22

TAPE

TAPE

TAPE

BUF AMPA1

BUF AMPA2

NABAMP1

NABAMP2

23

24

15

14

13

21

20

17

16

RADIO

BUF AMPB1

BUF AMPB2

MUTE

MUT

E

ON

ON

ON

7dB

26dB

26dB

MONITORAMP

LOGIC

18

19

MUTE

7dB

MONITORAMP

LINE

TAPERADIO

LINE

ALC2

ALC1

DET

RECAMP1

RECAMP2

2.1

REFAMP

MICAMP1

VCC

R.LO

LINE

R.RAD

TAPE

R.LIN

MIC

L.LO

REC

L.RAD

MIC I/EX

L.LINAGC

L.PO

L.NF

L.RO

L.IN

REF

GND

R.IN

R.RO

R.NF

R.PO

MIC.NF

IC301 TA2068N (TC Board)

34

CFD-S03CP/S03CPL

• IC PIN DESCRIPTIONS• IC201 CXD3014A-201R (RF AMP, SYSTEM SERVO PROCESSOR, DIGITAL SIGNAL PROCESSOR) (BD83S BOARD)

Pin No. Pin Name I/O Pin Description

1 LRCK O L/R sampling clock signal output terminal

2 LRCKI I L/R sampling clock signal input terminal

3 PCMD O Serial data output terminal

4 PCMDI I Serial data input terminal

5 BCK O Bit clock signal output terminal

6 BCKI I Bit clock signal input terminal

7 XTACN IOscillation circuit on/off switch control signal input from the system controller

“L”: oscillation stop, “H”: self-oscillation

8 XRST I System reset signal input from the system controller “L”: reset

9 VSS — Ground terminal

10 IREQ-MP3 O MP3 data request signal output to the system controller

11 CLOK I CD serial data transfer clock signal input from the system controller

12 DATA2 I MP3 serial data input/output with the system controller

13 XLAT-MP3 I MP3 serial data latch pulse signal input from the system controller

14 REQ-MP3 I MP3 data request signal input from the system controller

15 ACK-MP3 O MP3 acknowledge signal output to the system controller

16 XLAT I CD serial data latch pulse signal input from the system controller

17 VDD — Power supply terminal (+1.8V)

18 SVSS — Ground terminal

19 SVDD — Power supply terminal (+1.8V)

20 SENS O Internal status (SENSE) signal output to the system controller

21 WFCK — Not used

22 XUGF — Not used

23 XPCK — Not used

24 GFS — Not used

25 C2PO — Not used

26 SCOR O Subcode sync (S0+S1) detection signal output to the system controller


28 COUT — Not used



31 MIRR — Not used

32 DFCT — Not used

33 FOK — Not used




37 MIRR — Not used

38 MDP O Spindle motor servo control signal output terminal

39 SSTP I Disc inner position detection signal input terminal

40 IOVSS1 — Ground terminal

41 SFDR O Sled servo drive signal (+) output to the coil/motor driver

42 SRDR O Sled servo drive signal (–) output to the coil/motor driver

43 TFDR O Tracking servo drive signal (+) output to the coil/motor driver

44 TRDR O Tracking servo drive signal (–) output to the coil/motor driver

45 FFDR O Focus servo drive signal (+) output to the coil/motor driver

46 FRDR O Focus servo drive signal (–) output to the coil/motor driver

47 IOVDD1 — Power supply terminal (+3.3V)

35

CFD-S03CP/S03CPL

48 AVDD0 — Power supply terminal (+3.3V)

49 AVSS0 — Ground terminal

50 E I E signal input from the optical pick-up block

51 F I F signal input from the optical pick-up block

52 TEI I Tracking error signal input terminal

53 TEO O Tracking error signal output terminal

54 FEI I Focus error signal input terminal

55 FEO O Focus error signal output terminal

56 VC O Middle point voltage output terminal

57 A I A signal input from the optical pick-up block

58 B I B signal input from the optical pick-up block

59 C I C signal input from the optical pick-up block

60 D I D signal input from the optical pick-up block


62 RFDCO O Not used

63 PDSENS I Not used

64 AC_SUM O RFAC summing amplifier signal output terminal

65 EQ_IN I RF equalizer circuit input terminal

66 LD OLaser diode on/off control signal output to the automatic power control circuit

“L”: laser off, “H”: laser on

67 PD I Light amount monitor input from the optical pick-up block laser diode

68 RFC I Equalizer cut off frequency adjustment terminal


70 RFACO O EFM signal output terminal

71 RFACI I EFM signal input terminal


73 BIAS I Asymmetry circuit constant current input terminal

74 ASYI I Playback EFM asymmetry comparator voltage input terminal

75 ASYO O Playback EFM full-swing output terminal

76 VPCO O Charge pump output terminal for broad-band EFM PLL

77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL


79 CLTV I VCO1 control voltage input terminal for multiplier

80 FILO O Filter output terminal for master PLL

81 FILI I Filter input terminal for master PLL

82 PCO O Charge pump output terminal for master PLL



85 SSTB-MP3 I MP3 standby on/off control signal input terminal “L”: standby Not used



88 TEST1 I Test terminal Normally: fixed at “L”

89 DATA I CD serial data input from the system controller

90 CLK2 I MP3 serial data transfer clock signal input from the system controller



93 JTAGTCK — Not used

94 JTAGTDI — Not used

95 JTAGTDO — Not used

96 JTAGTMS — Not used


36

CFD-S03CP/S03CPL

97 TRST — Not used




101 DOUT O Digital audio signal output terminal Not used

102 TEST I Test terminal Normally: fixed at “L”

103 TES1 I Test terminal Normally: fixed at “L”


105 PLLVDD — Power supply terminal (+1.8V)

106 PLLVSS — Ground terminal

107 XVSS — Ground terminal

108 XTAO O System clock output terminal (16.9344 MHz)

109 XTAI I System clock input terminal (16.9344 MHz)

110 XVDD — Power supply terminal (+1.8V)


112 AOUT1 O L-ch analog audio signal output terminal

113 VREFL O L-ch reference voltage output terminal



116 VREFR O R-ch reference voltage output terminal

117 AOUT2 O R-ch analog audio signal output terminal





37

CFD-S03CP/S03CPL

• IC801 MB90802NPF-G-109E1 (SYSTEM CONTROL) (MAIN BOARD (2/3))


1 O-POWER O System power control output H: Power ON

2 FM/AM SHIFT O system clock shift control signal output

3 A-MUTE O A-mute signal output H: mute on

4 CD-XRST O CD reset signal output

5 O-DATA-MP3 O MP3 serial data output

6 O-CLK-MP3 O MP3 serial transfer clock output

7 I-DATA-MP3 I MP3 serial data input

8 I-CD-XLAT I CD LAT signal output

9 I-RMC I Remote commander receiver data input

10 O-XLAT-MP3 O MP3 LAT signal output

11 O-STBY-MP3 O CD mechanical mute signal output

12 O-RQ-MP3 O MP3 chip select signal output

13 X0A — Not used (Open)

14 X1A — Not used (Open)

15 VCC — Power supply (+3.3 V)

16 VSS — Ground

17 M-BASS O MEGA BASS control signal output

18 LID-OPEN I CD door open/close switch input L: Close

19 O-TU-CE O Tuner PLL chip enable signal output

20 O-TU-CLK O Tuner PLL serial transfer clock output

21 O-TU-DATA O Tuner PLL serial data output

22 I-TU-COUNT I Tuner PLL serial data input

23 O-CD-CLT O CD power control signal output H: CD ON

24 TAPE PLAY I Tape play switch signal input

25 TAPE REC I Tape record switch signal input H: REC

26 O-CD-XTCN O CD DSP oscillation control signal output

27 I-RQ-MP3 I MP3 REQ signal input

28 I-ACK-MP3 I MP3 acknowledgment detect signal input

29 I-CD-SENS I CD SENS signal input

30 O-CD-CLK O CD command transfer clock output

31 O-CD-CMD O CD command data output

32 AVCC — Power supply (+3.3 V)

33 VOL DATA O Volume command serial data output

34 VOL CLK O Volume command serial transfer clock output

35 AGND — Ground

36 REQ-CHK I Power supply CD 3.3V check signal input

37 BTT-CHK-H I Power supply 9V check signal input

38 V-CHECK I Power supply 6V check signal input

39 I-KEY0 I Key input

40 I-KEY1 I Key input

41 I-KET2 I Key input

42 WAKE-UP I Key wake-up signal input

43 I-CD-SCOR I CD Q-data request signal input

44 VSS — Ground

45 AC-CHK I AC IN check signal input

46 SDA I/O EEPROM serial data input/output

47 SCL O EEPROM transfer clock output

48 I-SUFFIX I Suffix distinction input

49 ISS1 O ISS control signal output

38

CFD-S03CP/S03CPL

50 ISS2 O ISS control signal output

51 MD2 I Operation mode setting pin



54 RESET I System reset signal input

55 CD-ON O Audio CD mode control signal output

56 TU-ON — Not used (Open)

57 TAPE O Audio tape mode control signal output

58 VLCD — Not used (Open)

59 to 62 COM4 to 4 O LCD drive common signal output

63 SEG29 O LCD drive segment signal output

64 SEG28 O LCD drive segment signal output


66 VSS — Ground

67 to 89 SEG27 to 5 O LCD drive segment signal output


91 VSS — Ground

92 X1 O Main system oscillation output (4.19 MHz)

93 X0 I Main system oscillation input (4.19 MHz)

94 to 97 SEG4 to 1 O LCD drive segment signal output

99 to 100 NC — Not used (Open)


39


EXPLODED VIEWS

1 2-654-054-01 LID, BATTERY (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

1 2-654-054-11 LID, BATTERY (LIGHT GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

1 2-654-054-21 LID, BATTERY (WHITE)...(WHITE) (MX)1 2-654-054-31 LID, BATTERY (PINK)...(PINK) (MX)2 3-252-833-01 SCREW (M3), (+) P

3 3-252-827-01 SCREW (B2.6), (+) BV TAPPING4 A-1157-013-A BATTERY-1 BOARD, COMPLETE5 3-229-975-01 SPRING, BATTERY (–)6 3-252-540-01 SPRING (+.–), BATTERY7 2-654-073-01 TERMINAL, ANTENNA

8 A-1157-012-A BATTERY-2 BOARD, COMPLETE9 A-1157-015-A POWER BOARD, COMPLETE (E92,MX)9 A-1157-362-A POWER BOARD, COMPLETE

(EXCEPT CND,E92,MX,TW)

9 A-1157-370-A POWER BOARD, COMPLETE (CND)9 A-1157-380-A POWER BOARD, COMPLETE (TW)10 2-654-040-02 CABINET (REAR) (GRAY)...(GRAY,SILVER)

(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)10 2-654-040-32 CABINET (REAR) (LIGHT GRAY)...(SILVER)

(AEP,UK,CET,IT,MX)10 2-654-040-61 CABINET (REAR) (WHITE)...(WHITE) (MX)

10 2-654-040-71 CABINET (REAR) (PINK)...(PINK) (MX)11 3-831-441-99 SHEET (1)ANT2 1-754-376-11 ANTENNA, TELESCOPIC (FM)

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)0T901 1-443-861-11 TRANSFORMER, POWER

(EXCEPT CND,E92,MX,TW)

0T901 1-443-871-11 TRANSFORMER, POWER (CND,E92,MX,TW)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE:• The mechanical parts with no reference

number in the exploded views are not supplied.• Items marked “*” are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinet’s Color

• Accessories are given in the last of this parts list.• Abbreviation

CND : Canadian modelCET : East European & Russian modelE41 : AC 230V area in E modelE92 : AC 120V area in E modelAUS : Australian modelKR : Korea modelMX : Mexican modelSP : Singapore modelIT : Italian modelAR : Argentina modelTH : Thai modelTW : Taiwan model

7-1. REAR CABINET SECTION

R R

ANT2

T901

F902

4

53

3

3

3

3

3

3

3

3

3

7

8

5

9

1

2

10

11

11

1111

6

6

Ver. 1.6

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Les composants identifiés par unemarque 0 sont critiques pourla sécurité.Ne les remplacer que par une piéceportant le numéro spécifié.

40

CFD-S03CP/S03CPL

51 3-252-827-01 SCREW (B2.6), (+) BV TAPPING52 2-655-159-02 JOINT, CABINET53 3-047-468-01 DAMPER54 2-654-071-01 SPRING, CASSETTE55 X-2103-302-2 HOLDER SUB ASSY, CASSETTE

(BLUE)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

55 X-2103-333-2 HOLDER SUB ASSY, CASSETTE(GRAY)...(SILVER) (UK,CET,IT,MX)

55 X-2103-334-1 HOLDER SUB ASSY, CASSETTE(GRAY)...(SILVER) (AEP)

55 X-2186-760-1 HOLDER SUB ASSY, CASSETTE(WHITE)...(WHITE,PINK) (MX)

56 A-1283-378-A MF-S01//C (including M901)57 2-654-047-01 BUTTON (PAUSE) (GRAY)...(GRAY,SILVER)

(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

57 2-654-047-11 BUTTON (PAUSE) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

57 2-654-047-21 BUTTON (PAUSE)(LIGHT GRAY)...(WHITE,PINK) (MX)

58 2-654-046-01 BUTTON (STOP) (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

58 2-654-046-11 BUTTON (STOP) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

58 2-654-046-21 BUTTON (STOP) (LIGHT GRAY)...(WHITE,PINK)(MX)

59 2-654-045-01 BUTTON (REW) (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

59 2-654-045-11 BUTTON (REW) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

59 2-654-045-21 BUTTON (REW) (LIGHT GRAY)...(WHITE,PINK)(MX)

60 2-654-044-01 BUTTON (FF) (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

60 2-654-044-11 BUTTON (FF) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

60 2-654-044-21 BUTTON (FF) (LIGHT GRAY)...(WHITE,PINK)(MX)

61 2-654-042-01 BUTTON (PLAY) (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

61 2-654-042-11 BUTTON (PLAY) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

61 2-654-042-21 BUTTON (PLAY) (LIGHT GRAY)...(WHITE,PINK)(MX)

62 2-654-043-01 BUTTON (REC) (GRAY)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

62 2-654-043-11 BUTTON (REC) (GRAY)...(SILVER)(AEP,UK,CET,IT,MX)

62 2-654-043-21 BUTTON (REC) (LIGHT GRAY)...(WHITE,PINK)(MX)

63 3-254-029-01 SCREW64 A-1156-999-A TC BOARD, COMPLETE (AEP,UK,CET,IT,KR)64 A-1158-597-A TC BOARD, COMPLETE

(CND,E41,E92,AUS,MX,SP,AR,TH,TW)65 3-253-143-01 SCREW (B2.6), (+) P TAPPING66 3-923-151-01 CUSHION, RUBBER

67 3-254-141-01 SCREW (B2.6), (+) BV TAPPING68 2-670-389-01 BELT (1)69 3-214-817-01 BELT (FR)70 3-254-140-01 SCREW (B2.6), (+) BV TAPPING


7-2. FRONT CABINET SECTION (1)

A

A not supplied

not supplied

5151

51

51

51

52

53

54

55

66

63

56

68

69

63

52 57

5859

6061

62

64

65

70

67Ver. 1.6

41

CFD-S03CP/S03CPL

101 A-1157-000-A KEY-1 BOARD, COMPLETE102 3-831-441-99 SHEET (1)103 1-831-616-11 CABLE, FLEXIBLE FLAT (4 CORE)104 1-831-613-11 CABLE, FLEXIBLE FLAT (4 CORE)105 2-654-050-02 BUTTON (FUNC) (BLUE)...(GRAY,SILVER)

105 2-654-050-31 BUTTON (FUNC) (WHITE)...(WHITE,PINK)106 3-252-827-01 SCREW (B2.6), (+) BV TAPPING107 A-1157-002-A KEY-2 BOARD, COMPLETE108 2-654-051-01 BUTTON (VOLUME) (GRAY)...(GRAY)

(CND,E41,E92,MX,AR)108 2-654-051-11 BUTTON (VOLUME) (LIGHT GRAY)...(SILVER)

(EXCEPT CND,E41,E92,MX,AR,TW,MX)

108 2-654-051-21 BUTTON (VOLUME) (WHITE)...(WHITE) (MX)108 2-654-051-31 BUTTON (VOLUME) (PINK)...(PINK) (MX)109 X-2102-579-1 CABINET (FRONT) SUB ASSY

(GUNMETALLIC)...(GRAY) (CND)

109 X-2103-199-1 CABINET (FRONT) SUB ASSY(SILVER)...(SILVER) (AEP,UK,CET,IT)

109 X-2103-301-1 CABINET (FRONT) SUB ASSY(GUNMETALLIC)...(GRAY) (E41,E92,MX,AR)

109 X-2103-331-1 CABINET (FRONT) SUB ASSY(SILVER)...(SILVER) (AUS,KR,SP,TH,TW,CET)

109 X-2186-747-1 CABINET (FRONT) SUB ASSY(SILVER)...(SILVER) (MX)

109 X-2186-759-1 CABINET (FRONT) SUB ASSY(WHITE)...(WHITE) (MX)

109 X-2186-764-1 CABINET (FRONT) SUB ASSY(PINK)...(PINK) (MX)

110 3-040-916-01 FOOT (FRONT), RUBBERSP101 1-826-280-11 SPEAKER (7.7cm) (L-CH)SP201 1-826-280-11 SPEAKER (7.7cm) (R-CH)


7-3. FRONT CABINET SECTION (2)

101

102

102

103 104

105 106

107

108

109

110

106

106

106

106

106

SP101

SP201

not supplied

not supplied

Ver. 1.6

42

CFD-S03CP/S03CPL

151 2-654-053-21 LID, CD (GRAY)...(SILVER) (AEP,UK,CET,IT,MX)151 2-654-053-31 LID, CD (BLUE)...(GRAY,SILVER)

(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)151 2-654-053-81 LID, CD (WHITE)...(WHITE,PINK) (MX)152 1-452-899-11 MAGNET153 3-019-395-01 PLATE, CHUCKING

154 3-253-143-01 SCREW (B2.6), (+) P TAPPING155 2-654-056-01 HANDLE (BLUE)...(GRAY,SILVER)

(CND.E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)155 2-654-056-11 HANDLE (GRAY)...(SILVER) (AEP,UK,CET,IT,MX)155 2-654-056-21 HANDLE (WHITE)...(WHITE,PINK) (MX)156 2-654-072-01 SPRING, CD

157 3-047-468-21 DAMPER

158 3-252-827-01 SCREW (B2.6), (+) BV TAPPING159 A-1157-008-A MAIN BOARD, COMPLETE (CND,E92,MX)159 A-1157-365-A MAIN BOARD, COMPLETE (E41,SP,TH)159 A-1157-386-A MAIN BOARD, COMPLETE (UK,CET,IT)159 A-1157-391-A MAIN BOARD, COMPLETE (AEP)

159 A-1157-967-A MAIN BOARD, COMPLETE (AUS,KR,TW)159 A-1157-973-A MAIN BOARD, COMPLETE (AR)160 1-832-008-11 CABLE, FLEXIBLE FLAT (14 CORE)161 3-923-151-01 CUSHION, RUBBER162 2-674-958-01 PAPER (MAIN), SHIELD

SW2 1-692-960-21 SWITCH, PUSH (1 KEY)(Z PUSH OPEN/CLOSE)


7-4. UPPER CABINET SECTION (1)

151

152

153

154

161

155

156

157

158

158158

158

159

160

162

SW2

Ver. 1.6

43

CFD-S03CP/S03CPL

201 3-923-736-01 COVER, CD202 3-931-379-21 RUBBER, VIBRATION PROOF (RED)203 3-931-379-31 RUBBER, VIBRATION PROOF (GREEN)204 1-832-404-21 CABLE, FLEXIBLE FLAT (16 CORE)205 1-831-973-21 CABLE, FLEXIBLE FLAT (23 CORE)

206 A-1134-279-A BD83S BOARD, COMPLETE207 3-252-827-01 SCREW (B2.6), (+) BV TAPPING208 2-654-055-21 CHASSIS, CD209 3-254-151-01 SCREW (B2.6), (+) P TAPPING210 A-1157-006-A PANEL BOARD, COMPLETE

211 1-832-009-11 CABLE, FLEXIBLE FLAT (20 CORE)212 2-673-399-01 SHEET (IR), ADHESIVE213 3-831-441-99 SHEET (1)214 2-654-058-01 WINDOW, LCD (CLEAR)...(GRAY,SILVER)

(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW)214 2-654-058-12 WINDOW, LCD (GLASS)...(SILVER)

(AEP,UK,CET,IT)

214 2-654-058-21 WINDOW, LCD (CLEAR)...(SILVER) (CET)

214 2-654-058-31 WINDOW, LCD (CLEAR)...(SILVER,PINK) (MX)214 2-654-058-41 WINDOW, LCD (GLASS)...(WHITE) (MX)215 A-1154-900-A HEADPHONE BOARD, COMPLETE216 X-2103-303-2 CABINET (UPPER) SUB ASSY

(BLUE)...(GRAY,SILVER)(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)

216 X-2103-332-2 CABINET (UPPER) SUB ASSY(GRAY)...(SILVER) (AEP,UK,CET,IT)

216 X-2186-748-1 CABINET (UPPER) SUB ASSY(GRAY)...(SILVER) (MX)

216 X-2186-761-1 CABINET (UPPER) SUB ASSY(WHITE)...(WHITE,PINK) (MX)

217 3-831-441-11 CUSHION (D)218 2-654-085-01 HOLDER, IRIC401 6-600-108-01 IC RPM7140 (IR)

LCD401 1-802-046-11 DISPLAY PANEL, LIQUID CRYSTALS201 1-771-853-11 SWITCH, DETECTION (LIMIT)#1 7-685-853-04 SCREW +BVTT 2X6 (S)


7-5. UPPER CABINET SECTION (2)

207207

201

202

203

203

205

206

208

204

210

209209

211211

213

212

218

213

214

LCD401

#1

IC401

S201

213

215

216

217

Ver. 1.6

44

CFD-S03CP/S03CPL

251 2-626-907-11 GEAR (A)252 2-627-003-01 GEAR (B) (RP)253 2-174-500-01 SCREW (2X3)254 2-626-908-01 SHAFT, SLED


7-6. CD MECHANISM SECTION(KSM-213CDP)

255 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR (SPINDLE)(including M701)

0256 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP)M702 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)

not supplied

M702

not supplied(M701 (SPINDLE))

254

256

253

251

252

255

45


ELECTRICAL PARTS LIST

A-1157-013-A BATTERY-1 BOARD, COMPLETE**************************

3-229-975-01 SPRING, BATTERY (–)

< CONNECTOR >

CN903 1-815-550-11 PIN, CONNECTOR (PWB) 2P*************************************************************

A-1157-012-A BATTERY-2 BOARD, COMPLETE**************************

3-229-975-01 SPRING, BATTERY (–)*************************************************************

A-1134-279-A BD83S BOARD, COMPLETE**********************

< CAPACITOR >

C101 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC102 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC103 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC104 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC105 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

C107 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC108 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC109 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC110 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC111 1-164-230-11 CERAMIC CHIP 220PF 5% 50V

C112 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC113 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC201 1-128-995-21 ELECT CHIP 100uF 20% 10VC202 1-164-360-11 CERAMIC CHIP 0.1uF 16VC203 1-128-995-21 ELECT CHIP 100uF 20% 10V

C204 1-164-360-11 CERAMIC CHIP 0.1uF 16VC205 1-164-360-11 CERAMIC CHIP 0.1uF 16VC206 1-164-360-11 CERAMIC CHIP 0.1uF 16VC207 1-128-995-21 ELECT CHIP 100uF 20% 10VC208 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C210 1-164-360-11 CERAMIC CHIP 0.1uF 16VC213 1-164-360-11 CERAMIC CHIP 0.1uF 16VC214 1-164-360-11 CERAMIC CHIP 0.1uF 16VC215 1-164-360-11 CERAMIC CHIP 0.1uF 16VC217 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C218 1-164-360-11 CERAMIC CHIP 0.1uF 16VC219 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C220 1-164-360-11 CERAMIC CHIP 0.1uF 16VC221 1-164-360-11 CERAMIC CHIP 0.1uF 16VC222 1-164-360-11 CERAMIC CHIP 0.1uF 16VC223 1-164-360-11 CERAMIC CHIP 0.1uF 16VC224 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C226 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC227 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC230 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC232 1-164-360-11 CERAMIC CHIP 0.1uF 16VC251 1-164-315-11 CERAMIC CHIP 470PF 5% 50V

C252 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC253 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC254 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC256 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC257 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C258 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC260 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3VC261 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC264 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC265 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C266 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC267 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50VC268 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC271 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC272 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C273 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC274 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC275 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50VC276 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC277 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C291 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC292 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC301 1-164-360-11 CERAMIC CHIP 0.1uF 16VC303 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3VC304 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C321 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC322 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC323 1-128-995-21 ELECT CHIP 100uF 20% 10VC401 1-128-394-11 ELECT CHIP 220uF 20% 10VC404 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C405 1-164-360-11 CERAMIC CHIP 0.1uF 16VC406 1-164-360-11 CERAMIC CHIP 0.1uF 16VC424 1-164-360-11 CERAMIC CHIP 0.1uF 16VC451 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V


NOTE:• Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.

• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORSuF : µF

• COILSuH : µH

• AbbreviationCND : Canadian modelCET : East European & Russian modelE41 : AC 230V area in E modelE92 : AC 120V area in E modelAUS : Australian modelKR : Korea modelMX : Mexican modelSP : Singapore modelIT : Italian modelAR : Argentina modelTH : Thai modelTW : Taiwan model

BATTERY-2BATTERY-1

BD83S

Ver. 1.2

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

Les composants identifiés par unemarque 0 sont critiques pourla sécurité.Ne les remplacer que par une piéceportant le numéro spécifié.

When indicating parts by referencenumber, please include the board.

46

CFD-S03CP/S03CPL

< CONNECTOR >

CN102 1-770-706-21 CONNECTOR, FFC/FPC 23PCN301 1-770-425-51 CONNECTOR, FFC/FPC 16P

< IC >

IC201 8-753-246-30 IC CXD3014A-201RIC202 6-708-736-01 IC BD18KA5FP-E2IC402 6-705-808-01 IC BA5947FM-E2

< TRANSISTOR >

Q321 6-551-120-01 TRANSISTOR 2SA2119K

< RESISTOR >

R101 1-216-809-11 METAL CHIP 100 5% 1/10WR102 1-216-809-11 METAL CHIP 100 5% 1/10WR103 1-216-809-11 METAL CHIP 100 5% 1/10WR104 1-216-809-11 METAL CHIP 100 5% 1/10WR105 1-216-809-11 METAL CHIP 100 5% 1/10W

R107 1-216-809-11 METAL CHIP 100 5% 1/10WR108 1-216-809-11 METAL CHIP 100 5% 1/10WR109 1-216-809-11 METAL CHIP 100 5% 1/10WR110 1-216-809-11 METAL CHIP 100 5% 1/10WR111 1-216-809-11 METAL CHIP 100 5% 1/10W

R112 1-216-809-11 METAL CHIP 100 5% 1/10WR113 1-216-809-11 METAL CHIP 100 5% 1/10WR201 1-216-295-11 SHORT CHIP 0R202 1-216-295-11 SHORT CHIP 0R203 1-500-445-21 FERRITE, EMI (SMD) (2012)

R207 1-216-295-11 SHORT CHIP 0R250 1-216-857-11 METAL CHIP 1M 5% 1/10WR252 1-216-833-11 METAL CHIP 10K 5% 1/10WR253 1-216-821-11 METAL CHIP 1K 5% 1/10WR254 1-216-833-11 METAL CHIP 10K 5% 1/10W

R255 1-216-821-11 METAL CHIP 1K 5% 1/10WR256 1-216-837-11 METAL CHIP 22K 5% 1/10WR257 1-216-845-11 METAL CHIP 100K 5% 1/10WR258 1-216-849-11 METAL CHIP 220K 5% 1/10WR260 1-216-864-11 SHORT CHIP 0

R265 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR266 1-216-821-11 METAL CHIP 1K 5% 1/10WR267 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR268 1-216-833-11 METAL CHIP 10K 5% 1/10WR270 1-216-821-11 METAL CHIP 1K 5% 1/10W

R271 1-216-857-11 METAL CHIP 1M 5% 1/10WR275 1-216-809-11 METAL CHIP 100 5% 1/10WR276 1-216-841-11 METAL CHIP 47K 5% 1/10WR277 1-216-809-11 METAL CHIP 100 5% 1/10WR278 1-216-809-11 METAL CHIP 100 5% 1/10W

R280 1-216-864-11 SHORT CHIP 0R291 1-216-809-11 METAL CHIP 100 5% 1/10WR292 1-216-809-11 METAL CHIP 100 5% 1/10WR321 1-216-789-11 METAL CHIP 2.2 5% 1/10WR322 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R323 1-216-864-11 SHORT CHIP 0R324 1-216-845-11 METAL CHIP 100K 5% 1/10WR401 1-216-295-11 SHORT CHIP 0R421 1-216-864-11 SHORT CHIP 0

R423 1-216-833-11 METAL CHIP 10K 5% 1/10WR451 1-216-837-11 METAL CHIP 22K 5% 1/10WR452 1-216-833-11 METAL CHIP 10K 5% 1/10W

< VIBRATOR >

X201 1-795-101-21 VIBRATOR, CERAMIC (16.93MHz)*************************************************************

A-1154-900-A HEADPHONE BOARD, COMPLETE***************************

< CAPACITOR >

C116 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC216 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

< CONNECTOR >

CN308 1-815-445-11 PIN, CONNECTOR (PWB) 4P

< JACK >

J321 1-815-325-11 JACK (i)

< RESISTOR >

R146 1-216-809-11 METAL CHIP 100 5% 1/10WR148 1-216-805-11 METAL CHIP 47 5% 1/10WR246 1-216-809-11 METAL CHIP 100 5% 1/10WR248 1-216-805-11 METAL CHIP 47 5% 1/10W

*************************************************************

A-1157-000-A KEY-1 BOARD, COMPLETE*********************

1-831-613-11 CABLE, FLEXIBLE FLAT (4 CORE) (FFC412)1-831-616-11 CABLE, FLEXIBLE FLAT (4 CORE) (FFC411)3-831-441-99 SHEET (1)

< RESISTOR >

R421 1-216-813-11 METAL CHIP 220 5% 1/10WR422 1-216-817-11 METAL CHIP 470 5% 1/10WR423 1-216-821-11 METAL CHIP 1K 5% 1/10W

< SWITCH >

S411 1-786-050-21 SWITCH, KEYBOARD (CD)S421 1-786-050-21 SWITCH, KEYBOARD

(RADIO/BAND/AUTO PRESET)S422 1-786-050-21 SWITCH, KEYBOARD (TAPE)

*************************************************************

A-1157-002-A KEY-2 BOARD, COMPLETE*********************

3-831-441-99 SHEET (1)

< CONNECTOR >

CN421 1-784-726-11 CONNECTOR, FFC 4P

< RESISTOR >

R424 1-216-821-11 METAL CHIP 1K 5% 1/10W


HEADPHONE KEY-1 KEY-2BD83S

47

CFD-S03CP/S03CPL

< SWITCH >

S423 1-786-050-21 SWITCH, KEYBOARD (VOLUME –)S424 1-786-050-21 SWITCH, KEYBOARD (VOLUME +)

*************************************************************

A-1157-008-A MAIN BOARD, COMPLETE (CND,E92,MX)A-1157-365-A MAIN BOARD, COMPLETE (E41,SP,TH)A-1157-386-A MAIN BOARD, COMPLETE (UK,CET,IT)A-1157-391-A MAIN BOARD, COMPLETE (AEP)A-1157-967-A MAIN BOARD, COMPLETE (AUS,KR,TW)

A-1157-973-A MAIN BOARD, COMPLETE (AR)*********************

1-832-008-11 CABLE, FLEXIBLE FLAT (14 CORE) (FFC802)2-674-958-01 PAPER (MAIN), SHIELD3-254-142-01 SCREW (B3), (+) BV TAPPING

< ANTENNA >

ANT1 1-754-116-12 ANTENNA, FERRITE-ROD (MW/LW) (AEP)ANT1 1-754-117-12 ANTENNA, FERRITE-ROD (AM) (EXCEPT AEP)

< CAPACITOR >

C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC2 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC4 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C6 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC7 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC9 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC10 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

(EXCEPT CND,E92,MX)C10 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

(CND,E92,MX)

C11 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC12 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC13 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC14 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V

(EXCEPT CND,E92,MX)C14 1-162-913-11 CERAMIC CHIP 8PF 0.5PF 50V

(CND,E92,MX)

C15 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC16 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC17 1-104-662-11 ELECT 22uF 20% 25VC18 1-126-963-11 ELECT 4.7uF 20% 50VC19 1-126-956-11 ELECT 0.1uF 20% 50V

C20 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC21 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC22 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC23 1-126-947-11 ELECT 47uF 20% 35VC24 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V

C25 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC26 1-115-156-11 CERAMIC CHIP 1uF 10VC27 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC28 1-115-156-11 CERAMIC CHIP 1uF 10VC29 1-126-925-11 ELECT 470uF 20% 10V

C30 1-126-923-11 ELECT 220uF 20% 10VC31 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

(CND,E92,MX)C32 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C33 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V(CND,E92,MX)

C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC35 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC36 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC37 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C38 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC39 1-126-923-11 ELECT 220uF 20% 10VC40 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC41 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC42 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V

C43 1-126-964-11 ELECT 10uF 20% 50VC45 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC46 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25VC51 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

(AEP)C52 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

(AEP)

C53 1-162-923-11 CERAMIC CHIP 47PF 5% 50V(AEP)


C55 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V(AEP)







(AEP)


C70 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC72 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC106 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC108 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C110 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC112 1-126-925-11 ELECT 470uF 20% 10VC113 1-126-960-11 ELECT 1uF 20% 50VC115 1-126-960-11 ELECT 1uF 20% 50VC117 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C119 1-104-658-11 ELECT 100uF 20% 10VC125 1-126-959-11 ELECT 0.47uF 20% 50VC127 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC129 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC130 1-126-957-11 ELECT 0.22uF 20% 50V

C131 1-126-947-11 ELECT 47uF 20% 35VC132 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC161 1-126-960-11 ELECT 1uF 20% 50VC162 1-126-960-11 ELECT 1uF 20% 50VC206 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V



MAINKEY-2Ver. 1.2

48

CFD-S03CP/S03CPL

C212 1-126-925-11 ELECT 470uF 20% 10VC213 1-126-960-11 ELECT 1uF 20% 50VC215 1-126-960-11 ELECT 1uF 20% 50VC217 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC219 1-104-658-11 ELECT 100uF 20% 10V

C225 1-126-959-11 ELECT 0.47uF 20% 50VC227 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC229 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC230 1-126-957-11 ELECT 0.22uF 20% 50VC231 1-126-947-11 ELECT 47uF 20% 35V

C232 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC261 1-126-960-11 ELECT 1uF 20% 50VC262 1-126-960-11 ELECT 1uF 20% 50VC311 1-126-965-11 ELECT 22uF 20% 50VC322 1-126-934-11 ELECT 220uF 20% 16V

C323 1-126-964-11 ELECT 10uF 20% 50VC324 1-164-156-11 CERAMIC CHIP 0.1uF 25VC325 1-126-937-11 ELECT 4700uF 20% 16VC326 1-126-923-11 ELECT 220uF 20% 10VC330 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C331 1-126-947-11 ELECT 47uF 20% 35VC349 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC350 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC353 1-126-925-11 ELECT 470uF 20% 10VC354 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C355 1-126-767-11 ELECT 1000uF 20% 16VC356 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC357 1-126-934-11 ELECT 220uF 20% 16VC358 1-164-156-11 CERAMIC CHIP 0.1uF 25VC451 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V

C452 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50VC453 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC454 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC455 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC456 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C457 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC458 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC461 1-126-964-11 ELECT 10uF 20% 50VC803 1-164-156-11 CERAMIC CHIP 0.1uF 25VC804 1-115-156-11 CERAMIC CHIP 1uF 10V

C805 1-104-658-11 ELECT 100uF 20% 10VC806 1-115-156-11 CERAMIC CHIP 1uF 10VC807 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC808 1-104-658-11 ELECT 100uF 20% 10VC811 1-216-864-11 SHORT CHIP 0

C813 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC814 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC815 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC816 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC817 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C818 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC819 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC820 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC821 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC822 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C823 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC825 1-115-156-11 CERAMIC CHIP 1uF 10VC951 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C952 1-162-974-11 CERAMIC CHIP 0.01uF 50VC953 1-126-925-11 ELECT 470uF 20% 10VC956 1-126-965-11 ELECT 22uF 20% 50VC957 1-162-974-11 CERAMIC CHIP 0.01uF 50VC959 1-126-923-11 ELECT 220uF 20% 10V

C961 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< FILTER >

CF2 1-767-555-11 FILTER, CERAMICCF3 1-781-962-21 FILTER, CERAMIC

< CONNECTOR >

CN304 1-815-552-11 PIN, CONNECTOR (PWB) 4PCN305 1-815-551-11 PIN, CONNECTOR (PWB) 3PCN306 1-815-552-11 PIN, CONNECTOR (PWB) 4PCN803 1-784-742-11 CONNECTOR, FFC 20PCN804 1-784-742-11 CONNECTOR, FFC 20P

CN805 1-779-291-11 CONNECTOR, FFC (LIF(NON-ZIF)) 23P

< TRIMMER >

CT1 1-141-304-21 CAP, CERAMIC TRIMMER 10PFCT3 1-141-442-91 CAP, CERAMIC TRIMMER 20PFCT5 1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF (AEP)

< DIODE >

D1 6-501-440-01 DIODE SVC707-ALD2 6-501-440-01 DIODE SVC707-ALD3 6-501-392-01 DIODE SVC386-ALD4 8-719-991-33 DIODE 1SS133T-77D5 8-719-991-33 DIODE 1SS133T-77

D6 6-500-697-01 DIODE UDZSTE-173.3BD322 8-719-991-33 DIODE 1SS133T-77D323 8-719-988-61 DIODE 1SS355TE-17D324 8-719-991-33 DIODE 1SS133T-77D461 6-500-335-01 DIODE MC2838-T112-1

D462 8-719-069-54 DIODE UDZSTE-175.1BD801 8-719-991-33 DIODE 1SS133T-77D802 6-500-334-01 DIODE MC2836-T112-1D951 6-500-334-01 DIODE MC2836-T112-1D952 8-719-991-33 DIODE 1SS133T-77

D953 8-719-978-33 DIODE DTZ-TT11-6.8BD957 8-719-083-58 DIODE UDZSTE-173.9B

< FERRITE BEAD >

FB831 1-216-864-11 SHORT CHIP 0FB832 1-500-445-21 FERRITE, EMI (SMD) (2012)

< IC >

IC1 6-708-840-01 IC LV23003VAIC302 6-701-919-01 IC PT2257-SIC303 6-703-710-01 IC TA8227PIC801 6-806-232-01 IC MB90802NPF-G-109E1IC802 6-703-740-01 IC S-24CS02AFT-TB-G

IC804 8-759-679-43 IC S-816A33AMC-BAI-T2-G (TYPE A)IC805 6-704-118-01 IC S-80828CNMC-B8NT2GIC806 6-706-338-01 IC XC6202P332FR (TYPE B)


MAIN


Ver. 1.4

49

CFD-S03CP/S03CPL

< JUMPER RESISTOR >

JC1 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP)JC2 1-216-864-11 SHORT CHIP 0 (AEP)JC3 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP)JC4 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP)JC101 1-216-864-11 SHORT CHIP 0

JC102 1-216-864-11 SHORT CHIP 0JC103 1-216-864-11 SHORT CHIP 0JC804 1-216-864-11 SHORT CHIP 0JC807 1-216-864-11 SHORT CHIP 0

< COIL >

L1 1-419-847-11 COIL, AIR-COREL2 1-419-655-11 COIL, AIR-COREL3 1-411-199-31 COIL, MW/LW OSCL6 1-457-168-11 COIL, DETL803 1-410-521-11 INDUCTOR 100uH

< TRANSISTOR >

Q31 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ (AEP)Q32 8-729-920-31 TRANSISTOR DTC343TK (AEP)Q33 8-729-054-77 TRANSISTOR 2SC4098-T106-PQ (AEP)Q35 8-729-601-58 TRANSISTOR 2SC3053-C (AEP)Q122 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q124 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q222 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q224 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q304 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q451 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q452 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q801 6-551-445-01 TRANSISTOR RT1N44QC-TP-1Q802 8-729-037-03 TRANSISTOR KTA1266GR-ATQ805 8-729-600-22 TRANSISTOR 2SA1235-FQ806 6-551-444-01 TRANSISTOR RT1N436C-TP-1

(AEP,AUS,KR,AR,TW)

Q808 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q951 6-551-444-01 TRANSISTOR RT1N436C-TP-1Q952 8-729-040-76 TRANSISTOR KTA1273-Y-ATQ953 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q955 8-729-018-99 TRANSISTOR 2SD2394-F

Q957 6-550-542-01 TRANSISTOR 2SD999-T1-AZQ958 6-551-443-01 TRANSISTOR RT1P436C-TP-1Q959 8-729-027-46 TRANSISTOR DTC114YKA-T146

< RESISTOR >

R1 1-216-845-11 METAL CHIP 100K 5% 1/10WR2 1-216-837-11 METAL CHIP 22K 5% 1/10WR3 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR4 1-216-797-11 METAL CHIP 10 5% 1/10WR5 1-216-833-11 METAL CHIP 10K 5% 1/10W

R6 1-216-853-11 METAL CHIP 470K 5% 1/10WR7 1-216-797-11 METAL CHIP 10 5% 1/10WR9 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR10 1-216-801-11 METAL CHIP 22 5% 1/10WR11 1-216-821-11 METAL CHIP 1K 5% 1/10W

R12 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR13 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR14 1-216-833-11 METAL CHIP 10K 5% 1/10WR15 1-216-837-11 METAL CHIP 22K 5% 1/10W

R16 1-216-864-11 SHORT CHIP 0R17 1-216-864-11 SHORT CHIP 0R18 1-216-809-11 METAL CHIP 100 5% 1/10WR19 1-216-809-11 METAL CHIP 100 5% 1/10WR20 1-216-809-11 METAL CHIP 100 5% 1/10W

R21 1-216-809-11 METAL CHIP 100 5% 1/10WR22 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR23 1-216-817-11 METAL CHIP 470 5% 1/10WR24 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR25 1-216-821-11 METAL CHIP 1K 5% 1/10W

R26 1-216-813-11 METAL CHIP 220 5% 1/10WR27 1-216-833-11 METAL CHIP 10K 5% 1/10WR28 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR29 1-216-833-11 METAL CHIP 10K 5% 1/10WR30 1-216-833-11 METAL CHIP 10K 5% 1/10W

(AEP)

R31 1-216-833-11 METAL CHIP 10K 5% 1/10W(AEP)



R35 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(AEP)



R38 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(AEP)

R39 1-216-864-11 SHORT CHIP 0R41 1-216-837-11 METAL CHIP 22K 5% 1/10WR134 1-216-813-11 METAL CHIP 220 5% 1/10W

R135 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR136 1-216-864-11 SHORT CHIP 0R138 1-216-817-11 METAL CHIP 470 5% 1/10WR139 1-216-833-11 METAL CHIP 10K 5% 1/10WR140 1-216-821-11 METAL CHIP 1K 5% 1/10W

R141 1-216-841-11 METAL CHIP 47K 5% 1/10WR142 1-216-821-11 METAL CHIP 1K 5% 1/10WR143 1-216-809-11 METAL CHIP 100 5% 1/10WR144 1-216-789-11 METAL CHIP 2.2 5% 1/10WR145 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R147 1-216-833-11 METAL CHIP 10K 5% 1/10WR161 1-216-841-11 METAL CHIP 47K 5% 1/10WR162 1-216-864-11 SHORT CHIP 0R234 1-216-813-11 METAL CHIP 220 5% 1/10WR235 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R236 1-216-864-11 SHORT CHIP 0R238 1-216-817-11 METAL CHIP 470 5% 1/10WR239 1-216-833-11 METAL CHIP 10K 5% 1/10WR240 1-216-821-11 METAL CHIP 1K 5% 1/10WR241 1-216-841-11 METAL CHIP 47K 5% 1/10W

R242 1-216-821-11 METAL CHIP 1K 5% 1/10WR243 1-216-809-11 METAL CHIP 100 5% 1/10WR244 1-216-789-11 METAL CHIP 2.2 5% 1/10WR245 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR247 1-216-833-11 METAL CHIP 10K 5% 1/10W

R261 1-216-841-11 METAL CHIP 47K 5% 1/10W


MAINVer. 1.1

50

CFD-S03CP/S03CPL

R262 1-216-864-11 SHORT CHIP 0R316 1-216-864-11 SHORT CHIP 0R321 1-216-809-11 METAL CHIP 100 5% 1/10WR323 1-216-857-11 METAL CHIP 1M 5% 1/10WR324 1-216-833-11 METAL CHIP 10K 5% 1/10W

R325 1-216-821-11 METAL CHIP 1K 5% 1/10WR326 1-216-821-11 METAL CHIP 1K 5% 1/10WR327 1-216-821-11 METAL CHIP 1K 5% 1/10WR328 1-216-809-11 METAL CHIP 100 5% 1/10WR329 1-216-809-11 METAL CHIP 100 5% 1/10W

R330 1-216-809-11 METAL CHIP 100 5% 1/10WR331 1-216-817-11 METAL CHIP 470 5% 1/10WR332 1-216-817-11 METAL CHIP 470 5% 1/10WR333 1-216-821-11 METAL CHIP 1K 5% 1/10WR335 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R336 1-216-833-11 METAL CHIP 10K 5% 1/10WR337 1-216-833-11 METAL CHIP 10K 5% 1/10WR338 1-216-833-11 METAL CHIP 10K 5% 1/10WR451 1-216-821-11 METAL CHIP 1K 5% 1/10WR452 1-216-821-11 METAL CHIP 1K 5% 1/10W

R453 1-216-833-11 METAL CHIP 10K 5% 1/10WR461 1-216-817-11 METAL CHIP 470 5% 1/10WR462 1-216-817-11 METAL CHIP 470 5% 1/10WR463 1-216-817-11 METAL CHIP 470 5% 1/10WR464 1-216-817-11 METAL CHIP 470 5% 1/10W

R465 1-216-817-11 METAL CHIP 470 5% 1/10WR466 1-216-817-11 METAL CHIP 470 5% 1/10WR467 1-216-821-11 METAL CHIP 1K 5% 1/10WR471 1-216-821-11 METAL CHIP 1K 5% 1/10WR472 1-216-821-11 METAL CHIP 1K 5% 1/10W




R490 1-216-864-11 SHORT CHIP 0R491 1-216-864-11 SHORT CHIP 0R492 1-216-864-11 SHORT CHIP 0R493 1-216-864-11 SHORT CHIP 0R801 1-216-821-11 METAL CHIP 1K 5% 1/10W


R810 1-216-821-11 METAL CHIP 1K 5% 1/10WR811 1-216-833-11 METAL CHIP 10K 5% 1/10WR812 1-216-821-11 METAL CHIP 1K 5% 1/10W

R813 1-216-821-11 METAL CHIP 1K 5% 1/10WR814 1-216-821-11 METAL CHIP 1K 5% 1/10WR815 1-216-809-11 METAL CHIP 100 5% 1/10WR816 1-216-809-11 METAL CHIP 100 5% 1/10WR817 1-216-821-11 METAL CHIP 1K 5% 1/10W


R823 1-216-821-11 METAL CHIP 1K 5% 1/10WR824 1-216-821-11 METAL CHIP 1K 5% 1/10WR825 1-216-821-11 METAL CHIP 1K 5% 1/10WR826 1-216-817-11 METAL CHIP 470 5% 1/10W

(CND,E92,MX,AR)R826 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

(AEP,AUS,KR,TW)

R827 1-216-817-11 METAL CHIP 470 5% 1/10W(AUS,KR,TW)

R827 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(AEP,AR)

R828 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR829 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR830 1-216-829-11 METAL CHIP 4.7K 5% 1/10W







R864 1-216-833-11 METAL CHIP 10K 5% 1/10WR865 1-216-833-11 METAL CHIP 10K 5% 1/10WR866 1-216-833-11 METAL CHIP 10K 5% 1/10WR867 1-216-833-11 METAL CHIP 10K 5% 1/10WR868 1-216-817-11 METAL CHIP 470 5% 1/10W


MAINVer. 1.2

51

CFD-S03CP/S03CPL



R879 1-216-821-11 METAL CHIP 1K 5% 1/10WR880 1-216-821-11 METAL CHIP 1K 5% 1/10WR883 1-216-845-11 METAL CHIP 100K 5% 1/10WR884 1-216-849-11 METAL CHIP 220K 5% 1/10W

(TYPE A)R885 1-216-821-11 METAL CHIP 1K 5% 1/10W

(TYPE A)


R892 1-216-864-11 SHORT CHIP 0R893 1-216-833-11 METAL CHIP 10K 5% 1/10WR894 1-216-833-11 METAL CHIP 10K 5% 1/10WR896 1-216-833-11 METAL CHIP 10K 5% 1/10WR897 1-216-833-11 METAL CHIP 10K 5% 1/10W

R898 1-216-817-11 METAL CHIP 470 5% 1/10W(UK,E41,CET,IT,SP,TH)

R899 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR951 1-216-841-11 METAL CHIP 47K 5% 1/10WR952 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR953 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R954 1-216-821-11 METAL CHIP 1K 5% 1/10WR955 1-216-821-11 METAL CHIP 1K 5% 1/10WR956 1-216-833-11 METAL CHIP 10K 5% 1/10WR957 1-216-833-11 METAL CHIP 10K 5% 1/10WR958 1-216-813-11 METAL CHIP 220 5% 1/10W

R959 1-216-809-11 METAL CHIP 100 5% 1/10WR960 1-216-821-11 METAL CHIP 1K 5% 1/10WR961 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR962 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR963 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R964 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR965 1-216-833-11 METAL CHIP 10K 5% 1/10W

< TRANSFORMER >

T1 1-433-741-11 TRANSFORMER, IF

< VIBRATOR >

X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz)X802 1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)

*************************************************************

A-1157-006-A PANEL BOARD, COMPLETE**********************

1-832-009-11 CABLE, FLEXIBLE FLAT (20 CORE)(FFC401,FFC402)

2-654-085-01 HOLDER, IR2-673-399-01 SHEET (IR), ADHESIVE3-831-441-99 SHEET (1)

< CAPACITOR >

C401 1-115-156-11 CERAMIC CHIP 1uF 10V

< CONNECTOR >


< DIODE >

D406 8-719-059-97 LED L-34HD (OPR/BATT)

< IC >

IC401 6-600-108-01 IC RPM7140 (IR)

< LIQUID CRYSTAL DISPLAY >

LCD401 1-802-046-11 DISPLAY PANEL, LIQUID CRYSTAL

< RESISTOR >

R401 1-216-813-11 METAL CHIP 220 5% 1/10WR402 1-216-817-11 METAL CHIP 470 5% 1/10WR403 1-216-821-11 METAL CHIP 1K 5% 1/10WR404 1-216-821-11 METAL CHIP 1K 5% 1/10WR405 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R406 1-216-821-11 METAL CHIP 1K 5% 1/10WR407 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR408 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR409 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR411 1-216-813-11 METAL CHIP 220 5% 1/10W

R412 1-216-817-11 METAL CHIP 470 5% 1/10WR413 1-216-821-11 METAL CHIP 1K 5% 1/10WR414 1-216-821-11 METAL CHIP 1K 5% 1/10WR415 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR416 1-216-821-11 METAL CHIP 1K 5% 1/10W

R417 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR418 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR419 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR430 1-216-813-11 METAL CHIP 220 5% 1/10WR431 1-216-841-11 METAL CHIP 47K 5% 1/10W

R432 1-216-845-11 METAL CHIP 100K 5% 1/10W

< SWITCH >

S401 1-786-050-21 SWITCH, KEYBOARD (z/OPERATE)(AEP,UK,CET,IT)

S401 1-786-050-21 SWITCH, KEYBOARD (z/POWER)(EXCEPT AEP,UK,CET,IT)

S402 1-786-050-21 SWITCH, KEYBOARD (SLEEP)S403 1-786-050-21 SWITCH, KEYBOARD (MEGA BASS)S404 1-786-050-21 SWITCH, KEYBOARD (DISPLAY/ENTER)

S405 1-786-050-21 SWITCH, KEYBOARD (MODE)S406 1-786-050-21 SWITCH, KEYBOARD (REPEAT)


MAIN PANELVer. 1.4


52

CFD-S03CP/S03CPL

S407 1-786-050-21 SWITCH, KEYBOARD (u)S413 1-786-050-21 SWITCH, KEYBOARD (./PRESET –)S414 1-786-050-21 SWITCH, KEYBOARD (>/PRESET +)S415 1-786-050-21 SWITCH, KEYBOARD ( /TUNE –)S416 1-786-050-21 SWITCH, KEYBOARD ( /TUNE +)

S417 1-786-050-21 SWITCH, KEYBOARD (x)*************************************************************

A-1157-015-A POWER BOARD, COMPLETE (E92,MX)A-1157-362-A POWER BOARD, COMPLETE

(EXCEPT CND,E92,MX,TW)A-1157-370-A POWER BOARD, COMPLETE (CND)A-1157-380-A POWER BOARD, COMPLETE (TW)

***********************

1-533-217-41 HOLDER, FUSE

< CAPACITOR >

C901 1-162-995-11 CERAMIC CHIP 0.022uF 50VC902 1-162-995-11 CERAMIC CHIP 0.022uF 50VC903 1-162-995-11 CERAMIC CHIP 0.022uF 50VC904 1-162-995-11 CERAMIC CHIP 0.022uF 50VC906 1-126-964-11 ELECT 10uF 20% 50V

< CONNECTOR >

CN902 1-815-443-11 PIN, CONNECTOR (PWB) 2P

< DIODE >

D901 8-719-063-79 DIODE 1N4002BD902 8-719-063-79 DIODE 1N4002BD903 8-719-063-79 DIODE 1N4002BD904 8-719-063-79 DIODE 1N4002B

< AC INLET >

0J901 1-526-818-11 INLET, AC (- AC IN) (E92,MX)0J901 1-526-838-11 INLET, AC 2P (- AC IN) (EXCEPT CND,E92,MX)0J901 1-540-009-11 INLET, AC (- AC IN) (CND)*************************************************************

A-1156-999-A TC BOARD, COMPLETE (AEP,UK,CET,KR,IT)A-1158-597-A TC BOARD, COMPLETE

(CND,E41,E92,AUS,MX,SP,AR,TH,TW)*******************

< CAPACITOR >

C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC102 1-104-658-11 ELECT 100uF 20% 10VC103 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC104 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C107 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC202 1-104-658-11 ELECT 100uF 20% 10VC203 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC204 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V

C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC207 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC301 1-104-658-11 ELECT 100uF 20% 10VC302 1-104-658-11 ELECT 100uF 20% 10VC303 1-104-658-11 ELECT 100uF 20% 10V

C304 1-126-947-11 ELECT 47uF 20% 35V

Ref. No. Part No. Description Remark

POWER TC

C305 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC307 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC308 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC309 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C310 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC312 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC318 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

< CONNECTOR >


< FERRITE BEAD >

FB201 1-216-864-11 SHORT CHIP 0(CND,E41,E92,AUS,MX,SP,AR,TH,TW)

FB201 1-414-445-11 FERRITE, EMI (SMD) (1608)(AEP,UK,CET,KR,IT)













< IC >

IC301 8-759-264-71 IC TA2068N

< JUMPER RESISTOR >

JC302 1-216-864-11 SHORT CHIP 0JC303 1-216-864-11 SHORT CHIP 0JC305 1-216-864-11 SHORT CHIP 0JC306 1-216-864-11 SHORT CHIP 0JC307 1-216-864-11 SHORT CHIP 0

JC308 1-216-864-11 SHORT CHIP 0

< TRANSISTOR >

Q301 8-729-901-81 TRANSISTOR 2SC2412K-T-146-RQ302 8-729-027-46 TRANSISTOR DTC114YKA-T146Q303 8-729-027-46 TRANSISTOR DTC114YKA-T146

< RESISTOR >

R101 1-216-837-11 METAL CHIP 22K 5% 1/10W

Ref. No. Part No. Description Remark

PANELVer. 1.2

53

CFD-S03CP/S03CPL

R102 1-216-805-11 METAL CHIP 47 5% 1/10WR103 1-216-845-11 METAL CHIP 100K 5% 1/10WR104 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR105 1-216-837-11 METAL CHIP 22K 5% 1/10WR106 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R107 1-216-841-11 METAL CHIP 47K 5% 1/10WR108 1-216-801-11 METAL CHIP 22 5% 1/10WR109 1-216-849-11 METAL CHIP 220K 5% 1/10WR110 1-216-809-11 METAL CHIP 100 5% 1/10WR111 1-216-833-11 METAL CHIP 10K 5% 1/10W

R112 1-216-821-11 METAL CHIP 1K 5% 1/10WR201 1-216-837-11 METAL CHIP 22K 5% 1/10WR202 1-216-805-11 METAL CHIP 47 5% 1/10WR203 1-216-845-11 METAL CHIP 100K 5% 1/10WR204 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R205 1-216-837-11 METAL CHIP 22K 5% 1/10WR206 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR207 1-216-841-11 METAL CHIP 47K 5% 1/10WR208 1-216-801-11 METAL CHIP 22 5% 1/10WR209 1-216-849-11 METAL CHIP 220K 5% 1/10W

R210 1-216-809-11 METAL CHIP 100 5% 1/10WR211 1-216-833-11 METAL CHIP 10K 5% 1/10WR212 1-216-821-11 METAL CHIP 1K 5% 1/10WR301 1-216-857-11 METAL CHIP 1M 5% 1/10WR302 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R303 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR304 1-216-821-11 METAL CHIP 1K 5% 1/10WR305 1-216-817-11 METAL CHIP 470 5% 1/10WR306 1-216-833-11 METAL CHIP 10K 5% 1/10WR307 1-216-797-11 METAL CHIP 10 5% 1/10W

R308 1-216-837-11 METAL CHIP 22K 5% 1/10WR309 1-216-805-11 METAL CHIP 47 5% 1/10WR310 1-216-857-11 METAL CHIP 1M 5% 1/10WR311 1-216-857-11 METAL CHIP 1M 5% 1/10WR312 1-216-837-11 METAL CHIP 22K 5% 1/10W

R314 1-216-817-11 METAL CHIP 470 5% 1/10WR315 1-216-817-11 METAL CHIP 470 5% 1/10W

< SWITCH >

S301 1-786-126-11 SWITCH, SLIDE (REC/PB)

< TRANSFORMER >

T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION*************************************************************

MISCELLANEOUS***************

56 1-797-376-11 DECK, MECHANICAL (including M901)152 1-452-899-11 MAGNET204 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)205 1-831-973-11 CABLE, FLEXIBLE FLAT (23 CORE)255 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR (SPINDLE)

(including M701)

0256 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP)ANT2 1-754-376-11 ANTENNA, TELESCOPIC (FM)

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)M702 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)S201 1-771-853-11 SWITCH, DETECTION (LIMIT)

SW2 1-692-960-21 SWITCH, PUSH (1 KEY)(Z PUSH OPEN/CLOSE)

SP101 1-826-280-11 SPEAKER (7.7cm) (L-CH)SP201 1-826-280-11 SPEAKER (7.7cm) (R-CH)

0T901 1-443-861-11 TRANSFORMER, POWER(EXCEPT CND,E92,MX)

0T901 1-443-871-11 TRANSFORMER, POWER (CND,E92,MX)*************************************************************

ACCESSORIES************

0 1-590-342-12 CORD, POWER (E92,MX)0 1-769-412-22 CORD, POWER (AEP,CET,E41,IT,SP,TH)0 1-770-019-61 ADAPTOR, CONVERSION PLUG (UK)0 1-776-985-12 CORD, POWER (KR)0 1-782-126-11 CORD, POWER (CND)

0 1-783-952-21 CORD, POWER (AR)0 1-827-945-12 CORD, POWER (AUS)0 1-827-946-21 CORD, POWER (UK)0 1-829-433-11 CORD, POWER (TW)

2-655-836-11 MANUAL, INSTRUCTION (ENGLISH)(CND,E92,TW)

2-655-836-21 MANUAL, INSTRUCTION (SPANISH) (E92,MX)2-655-836-31 MANUAL, INSTRUCTION (FRENCH) (AEP,SP)2-655-836-41 MANUAL, INSTRUCTION (GERMAN) (AEP)2-655-836-51 MANUAL, INSTRUCTION

(DUTCH,PORTUGUESE) (AEP)2-655-836-61 MANUAL, INSTRUCTION (ITALIAN) (IT)

2-655-836-71 MANUAL, INSTRUCTION (FINNISH,SWEDISH)(CET)

2-655-836-81 MANUAL, INSTRUCTION (POLISH) (CET)2-655-836-91 MANUAL, INSTRUCTION (CZECH,HUNGARIAN)

(CET)2-655-837-11 MANUAL, INSTRUCTION

(SLOVAKIAN,RUSSIAN) (CET)2-655-837-21 MANUAL, INSTRUCTION (ENGLISH)

(AEP,UK,AUS,KR,E41,AR,SP,TH)

2-655-837-31 MANUAL, INSTRUCTION (KOREAN) (KR)2-655-837-41 MANUAL, INSTRUCTION

(TRADITIONAL CHINESE) (TW)2-655-837-51 MANUAL, INSTRUCTION (FRENCH) (CND)2-655-837-61 MANUAL, INSTRUCTION (SPANISH)

(AEP,E41,AR)2-655-837-71 MANUAL, INSTRUCTION (UKRAINIAN) (CET)

3-238-070-01 LID, BATTERY CASE (for RMT-CE95A/CE95AD)A-3172-070-A REMOTE COMMANDER (RMT-CE95AD)

(AEP,UK,CET,IT)A-3172-079-A REMOTE COMMANDER (RMT-CE95A)

(CND,E41,E92,AUS,AR,KR,MX,SP,TH,TW)


TCVer. 1.5

5454

CFD-S03CP/S03CPL

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the top of the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision

1.0 2006.01 New

1.1 2006.02 E41, Australian, Italian, Argentina, Thai and Taiwan model addition.

1.2 2006.03 Canadian model addition.

1.3 2006.04 Silver model addition of blue type to CET model.

1.4 2007.03 Change of 3.3V regulator circuit. (SPM-07020)

1.5 2007.07 MANUAL, INSTRUCTION of ukrainian is added to East European &

Russian models of CFD-S03CP. (SPM-07058)

1.6 2007.08 Color variation addition to Mexican model (silver, white, pink).

cfd-s03cp (1)

Documents