conjunto de planos constructivos de muebles y otros objetos
Post on 08-Aug-2018
214 Views
Preview:
TRANSCRIPT
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 1/203
U-BILD
Animal ArkPlan No. 786Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 2” x 12” x 28” pine A
1 1” x 6” x 84” pine B, C, D, E, F
4 1” x 12” x 12’ lumber of choice* G, animals**
1 box 1 1/4” finish nails
1 bottle wood glue
1 bottle mineral oil
*We used fir, mahogany, pine and walnut.**Quantity listed is enough for two of each animal.
This do-it-yourself animal ark project will keep little hands and big imaginations busy when it’s too wet to go outside. A natural for
rainy afternoons, the project features pairs of lions, giraffes, bears, pigs, cows, elephants, horses and camels that fit on a sturdy ark
And when the deluge is over, the whole menagerie is ready to go outside into the sunshine for outdoor fun.
The finished ark measures 27 inches long by 11 inches wide by 10 inches tall, and each animal measures approximately 4 inches
long by 4 inches tall.
NOTES
1. Read all instructions and check materials
before beginning work.
2. Read manufacturer’s instructions before
operating equipment.
3. Always wear safety glasses.
4. Use wood glue and 1 1/4” finish nails on all
joints.
Cutting Schedule
Part Qty T W L Material
A 1 1 1/2” 11” 27” pine
B 2 3/4” 3 1/4” 25 7/8” pine
C 2 3/4” 4 3/4” 12” pine
D 1 3/4” 7 1/8”* 4 3/4” pine
E 1 3/4” 4 3/4” 14” pine
F 1 3/4” 5 1/2” 14” pine
G 1 3/4” 2 1/2” 12” lumber of choice
animals 16 3/4” see traceable patterns lumber of choice
*Board D is made up of two boards edge-glued to achieve width
(see Figure 1)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 2/203
G
F
E
CD
B
A
A
C
D
E
F
B
Isometric
Figure 1Ark Cross Section
Direction of grain
for Board D
10
45
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 3/203
1 0
1 0 1 / 2 ”
1 4 1 / 4 ”
2 3 / 8 ”
5 5 / 8 ”
3 ” T Y P .
2 ” T Y P .
A
B
C
DD
C
B
A
F
E
SeePattern
1
SeePattern
2
CenterL
ine
( Note:EandFno
tshown)
3/8”radius
3/8”radius
F i g ur e2
Ar k C on s t r u c t i onDi a g
r am
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 4/203
Pattern 1
A
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 5/203
Pattern 2
A
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 6/203
Animal Pattern Sheet 1
Cow
Pig
Horse
Bear
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 7/203
Animal Pattern Sheet 2
Camel
Giraffe
Elephant
Lion
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 8/203
2. Place rails (B) in position on base (A). Make a mark at either end of both boards (B) and remove from board (A). Route a 3/8”radius between the marks at either end of board (A). Refer to Figure 2.
3. Attach rails (B) to base (A) using glue and 1 1/4” finish nails. Refer to Isometric, Figures 1 and 2 and Patterns 1 and 2.
4. Drill two 1 3/4” portholes in deckhouse sides (C). Refer to Figure 2.
5. Attach roof board (E) to roof board (F) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 1.
6. Route a 3/8” radius on all all exposed (when assembled) edges of boards (B), (C), (E), (F) and (G).
7. Attach deckhouse sides (C) to deckhouse divider (D) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 2.
8. Attach deckhouse (C, D) to base (A) using glue. Refer to Isometric and Figure 2.
9. Attach deckhouse roof (F, E) to deckhouse (C, D) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 2.
10. Fill all nail holes and sand completed ark.
11. Trace, cut out and sand animals. Drill 1/16” diameter by 1/16” deep holes for the animals’ eyes. Refer to Animal Pattern Sheets
1 and 2.
12. Apply nontoxic mineral oil finish to ark and animals.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Cut out all parts. Refer to Cutting Schedule, Isometric, Figures 1 and 2 and Patterns 1 and 2. Note that ark base (A) is cut out
with a 10 bevel around the edges and deckhouse sides (C) have a 45 bevel on the top edge.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 9/203
U-BILD
ArmoirePlan No. 729Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
3 1” x 2” x 84” lumber of choice A, F, G, P, Q, R
8 1” x 3” x 72” lumber of choice B, E, S, U,Y, Z
2 1” x 5” x 84” lumber of choice C, I, J, T, DD
1 1” x 8” x 108” lumber of choice N, AA
1 1” x 8” x 144” lumber of choice BB
1 1” x 10” x 120” lumber of choice K, L, M
5 1” x 12” x 72” lumber of choice D, V
1 3/4” x 48” x 96” veneer plywood H, W, X
1 1/8” x 48” x 96” hardboard O, CC1 96” moulding* EE
1 96” moulding* FF
1 96” moulding* GG
1 1 3/8” diameter x 36” clothes rod HH
2 1 3/8” clothes rod brackets
6 3/8” x 3/8” cabinet hinges
2 drawer pulls
2 door knobs
1 box 1 1/2” finish nails
1 box 1/2” finish nails
1 bottle wood glue
finish of choice**
* See Figures 12 and 13 for suggested moulding profiles.** We used satin polyurethane over a medium stain
If you’re looking for an easy way to add somestorage or closet space for that winter wardrobe,an armoire is a handsome, easy-to-build solution.This one will stow full-length coats, robes andgowns and has a roomy drawer at the bottom forlinens, handbags and more.
The armoire measures 77 inches tall by 38 inch-es wide by 22 inches deep. The doors are five feettall and allow easy access to the interior.
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 1 1/2” 13 1/2” lumber of choice
B 1 3/4” 2” 34 1/2” lumber of choice
C 1 3/4” 4” 34 1/2” lumber of choice
D 2 3/4” 22 1/4”* 13 1/2” lumber of choice
E 2 3/4” 2” 21 1/2” lumber of choice
F 2 3/4” 1 1/4” 21 1/2” lumber of choice
G 1 3/4” 1 1/2” 21 1/2” lumber of choice
H 1 3/4” 36” 13 1/2” veneer plywood
I 1 3/4” 4” 39” lumber of choiceJ 2 3/4” 4” 23 3/4” lumber of choice
K 1 3/4” 23 3/4”* 39” lumber of choice
L 1 3/4” 8 1/8” 35 1/4” lumber of choice
M 2 3/4” 7 3/8” 21 1/2” lumber of choice
N 1 3/4” 6 1/2” 33 1/2” lumber of choice
O 1 1/8” 20 3/4” 33 1/2” hardboard
P 1 3/4” 1 1/2” 20 3/4” lumber of choice
Q 2 3/4” 1 1/2” 20 1/2” lumber of choice
R 2 3/4” 1 1/2” 31” lumber of choice
S 2 3/4” 2” 60” lumber of choice
T 1 3/4” 3 3/4” 31 1/2” lumber of choice
U 1 3/4” 2” 31 1/2” lumber of choice
V 2 3/4” 21 1/4”* 60” lumber of choice
W 1 3/4”
34”
21 1/4”
veneer plywoodX 1 3/4” 34” 59 1/4” veneer plywood
Y 4 3/4” 2” 55” lumber of choice
Z 6 3/4” 2” 12” lumber of choice
AA 2 3/4” 12”* 16” lumber of choice
BB 2 3/4” 12”* 33” lumber of choice
CC 2 1/8” 16” 55” hardboard
DD 1 3/8” 5/8” 54 1/4” lumber of choice
EE 3 cut to fit moulding
FF 3 cut to fit moulding
GG 3 cut to fit moulding
HH 1 cut to fit clothes rod
* Edge-gluing required to achieve width.
NOTES1. Read manufacturer’s instructions before operating equip-
ment.
2. Always wear safety glasses.
3. We used pine for this project, but oak or birch will work
equally well.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 10/203
W
FF
GG
X
VS
Q
G
F
E
EE CC
U
Y
Z
T
R
K
D
H
J
C
O
N
L
M
I
B
A
DD
Isometric
P
AA
BB
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 11/203
A A
B B
AA
Pattern 1A
Pattern 1B
Center
Line
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 12/203
B B
Pattern 1C
Pattern 1A Pattern 1B Pattern 1C
A
A B
B
Pattern 1Assemble as Pictured
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 13/203
Pattern 2A Pattern 2B
A
A
Pattern 2Assemble as Pictured
A
A
A
A
Pattern 2A
Pattern 2B
Ce
n
t
e
r
L
i
n
e
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 14/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 1Boards (D), (E), (F), (H)
(Left Side)
Figure 2Boards (C), (G), (H)
1. Assemble lower face frame (A, B, C) using glue. Refer to Isometric. (Note: You may wish to reinforce the joints with 3/8” by
2” dowels.
2. Attach boards (E) to boards (F) using glue and 1 1/4” finish
nails. Refer to Figure 1 and Isometric.
3. Attach subassemblies (E, F) to lower sides (D) using glue and
1 1/4” finish nails. Refer to Figure 1 and Isometric.
4. Attach lower back (H) to lower side subassemblies (D, E, F)
using glue and 1 1/4” finish nails. Refer to Figure 1 and
Isometric.
5. Attach lower face frame (A, B, C) to boards (D), (E) and (F) using glue and 1 1/4” finish nails. Refer to Isometric.
6. Attach drawer guide (G) to boards (C) and (H) using glue and 1 1/4” finish nails.
Refer to Figure 2 and Isometric.
1/2”D
E
F
H
G
C
H
3/8”
Center Line
7. Miter both ends of base board (I). Refer to Isometric.
8. Miter one end of base boards (J). Refer to Isometric.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 15/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Figure 3Boards (D), (J)
(Left Side)
Figure 4Boards (A), (B), (D), (K), (Q), (R)
(Left Side)
D
J
11. Cut a 1/4” radius on the outside upper edge of base boards (I) and (J). Refer to Figure 3.
12. Attach base boards (I) and (J) to lower cabinet (A, B, C, D, E, F, G, H) using glue
and 1 1/4” finish nails. Refer to Figure 3 and Isometric.
14. Attach boards (Q) and (R) to board (K) using
glue and 1 1/4” finish nails. Refer to Figure 4
and Isometric.
9. Trace Pattern 1 onto base board (I), cut out curves and sand.
10. Trace Pattern 2 onto base boards (J), cut out curves and sand.
R 1/4”
1 11/16”
RQ
K
BAD
2 1/2”
3/4”
15. Assemble upper face frame (S, T, U) using glue. Refer to Isometric. (Note: You may wish to reinforce the joints with 3/8” by
2” dowels.
13. Attach board (K) to lower cabinet using using
glue and 1 1/4” finish nails. Refer to Figure 4
and Isometric.
16. Attach upper sides (V) to top (W) using glue and 1 1/4” finish nails. Refer to Isometric.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 16/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
17. Attach upper sides (V) to top (W) using glue and 1 1/4” finish nails. Refer to Isometric.
18. Attach upper back (X) to subassembly (V, W) using glue and 1 1/4” finish nails. Refer to Isometric.
19. Attach upper face frame (S, T, U) to subassembly (V, W, X) using glue and 1 1/4” finish nails. Refer to Isometric.
20. Place upper cabinet on top of lower cabinet and attach
boards (U), (V) and (X) to boards (Q) and (R) using glue and
1 1/4” finish nails. Refer to Figure 5 and Isometric.
RQ
K
U
S
X
V
Y
CC
Z
Figure 5Boards (K), (B), (Q), (R), (S), (U), (V), (X)
(Left Side)
Figure 6Door Subassembly (Y, Z, CC) Detail
21. Assemble door frames (Y, Z) using glue. Refer to Isometric.
22. Attach door backing boards (CC) to frames (Y, Z) using glue. Refer to Isometric.
23. Cut a 3/8” wide by 1/2” deep rabbet around inside edge of
subassembly (Y, Z, CC). Refer to Figure 6.
23. Cut a 1/4” decorative radius around outside edge of sub-
assembly (Y, Z, CC). Refer to Figure 6.
1/2”
3/8”
R 1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 17/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
Figure 7Door Panel (AA), (BB) Detail
Figure 8Subassembly (M, N O) Detail(Front View)
24. Cut a decorative raised panel around outside edge of door panels (AA) and (BB).
Refer to Figure 7.
25. Glue door panels (AA) and (BB) to door backing boards (CC) inside door frames (Y, Z). Refer to Isometric.
3/4”
AA, BB
28. Cut a 3/4” wide by 3/8” deep dado on the back end of the inside width of drawer sides (M) that extends from the top edge of (M)
to the 1/8” dado cut in Step 26. Refer to Figure 9 and Isometric.
27. Cut a 1/8” wide by 3/8” deep dado along the inside length of drawer sides (M). Refer to Figure 8 and Isometric.
30. Slide drawer back (N) into the 3/4” dado in drawer sides (M). Attach (N) to (M) using glue and 1 1/4” finish nails and (N) to
(O) using glue and 1/2” finish nails. Refer to Figure 9 and Isometric.
29. Slide drawer bottom (O) into the 1/8” dado in boards (M) until it is flush with the front end of boards (M). Refer to Figure 8
and Isometric.
3/4” 1/4”
3/8”
MN
O
26. Attach board (DD) to left door using glue and 1/2” finish nails. Refer to Figure 14 and
Isometric.
Figure 13
Board (DD) Detail
DDY
Figure 9Subassembly (M, N O) Detail
(Top View)
3/4”
3/4”
3/8”
M
N
O
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 18/203
M L
3/8”
3/8”
R 1/4”
30. Cut a 3/8” wide by 3/8” deep rabbet around inside edge of drawer front (L). Refer to
Figure 10.
33. Cut a 3/4” wide by 3/8” deep dado lengthwise in drawer guide (P). Refer
to Figure 11.
34. Center drawer guide (P) on the width of drawer bottom (O) and attach using glue and 1/2” finish nails. Refer to Isometric.
31. Cut a 1/4” decorative radius around outside edge of drawer front (L). Refer to Figure 10.
32. Center drawer front (L) horizontally on subassembly (M, N, O) and attach using glue
and 1 1/4” finish nails. Refer to Figure 10 and Isometric.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Five
O
Figure 10
Drawer Front (L) Detail(Side View)
Figure 11
Board (P) Detail
3/8”
3/8”
P
3/4”
35. Install clothes rod brackets centered on inside of upper sides (D) 3” below top (W).
36. Cut clothes rod (HH) to length and install on clothes rod brackets.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 19/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Six
37. Cut decorative moulding (EE), (FF) and (GG) to length and install using glue and 1/2” finish nails. Refer to Figures 12 and 13
and Isometric.
38. Sand project.
39. Apply finish to cabinet, doors and drawer front.
40. Install doors. Note: Hinges are placed 3” from the top, in the center and 3” from the bottom of outside door stiles (Y).
41. Install door pulls.
42. Install drawer pulls.
41. Install drawer.
Figure 13Moulding (FF) and (GG) Detail
(Shown at 50%)
WFF
V
GG
Figure 12Moulding (EE) Detail
(Shown at 50%)V
K
EE
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 20/203
U-BILD
Bathroom Cabinet
Plan No. 915Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 3/4” x 48” x 96” birch plywood F, G, P, S, W, BB, GG
1 1/4” x 48” x 48” birch plywood E, O
25 BF* 3/4” birch A, B, C, D, H, I, J, K, L, M, N, Q, R, T, U, V,
X, Y Z, AA, CC, DD, EE, FF, HH, II
2 1/8” x 9 1/16” x 29 7/16” tempered glass sides
1 1/8” x 14 9/16” x 30 1/16” tempered glass door
36 3/8” x 2” dowels
12 5/16” x 3/4” glass clips
12 1/4” shelf supports
2 pairs 3/4” x 2 3/4” full back-to-back wraparound hinges
2 1 5/8” x 1 3/4” cupboard latches
1 box 1” finish nails
1 box 1 1/4” finish nails
1 small can wood filler
1 small bottle wood glue
2 quarts primer
2 quarts white paint
*includes about 20% scrap
NOTES1. Read all instructions and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. “Subassembly” means two or more boards put together to make a component of a larger part of the project
4. Use wood glue on all joints.
5. Always wear safety glasses.
With storage space at a premium in most homes, antique medical cabinets have
become a popular (and expensive) way to add storage space to the bathroom.
This do-it-yourself version, based on a classic doctor’s cabinet, includes the
gleaming display space, generous storage and bright white finish of the originals,
but without the expense of an antique.
Perfect for linens and toiletries, the project makes a great addition to the pow-
der room. With its clean lines and pleasing proportions, it’s also at home in the
kitchen or dining room as a handsome curio cabinet.
The bathroom cabinet measures 68 inches tall by 24 inches wide by 14 inchesdeep.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 21/203
Item Qty T W L Material
A 2 3/4” 2 3/8” 30 3/4” birch
B 2 3/4” 1 5/8” 30 3/4” birch
C 2 3/4” 2 3/8” 8 3/8” birch
D 2 3/4” 6” 8 3/8” birch
E 2 1/4” 9 1/8” 23 1/8” birch plywood
F 1 3/4”
20 1/2”
30 3/4”
birch plywoodG 1 3/4” 11 5/8” 20 1/2” birch plywood
H 2 3/4” 1 5/8” 30 3/4” birch
I 1 3/4” 1 5/8” 18 3/4” birch
J 1 3/4” 5” 18 3/4” birch
K 2 3/4” 4” 13 7/8” birch
L 1 3/4” 4” 23 1/2” birch
M 2 3/4” 2 3/8” 24” birch
N 2 3/4” 2 3/8” 13 7/8” birch
O 1 1/4” 14 5/8” 20” birch plywood
P 1 3/4” 13 3/8” 22 1/2” birch plywood
Q 2 1/2” 3/4” 13 7/8” birch
R 1 1/2” 3/4” 23 1/2” birch
Item Qty T W L Material
S 1 3/4” 11 5/8” 20 1/2” birch plywwod
T 2 3/4” 2 3/8” 35 3/4” birch
U 2 3/4” 1 5/8” 35 3/4” birch
V 4 3/4” 3 1/2” 8 3/8” birch
W 1 3/4” 20 1/2” 35 3/4” birch plywwod
X 2 3/4”
1 5/8”
35 3/4”
birchY 1 3/4” 1 1/2” 18 3/4” birch
Z 2 3/4” 2 3/8” 34 1/8” birch
AA 2 3/4” 2 3/8” 13 7/8” birch
BB 1 3/4” 13 7/8” 23 1/2” birch plywwod
CC 2 1/2” 3/4” 14 3/8” birch
DD 1 1/2” 3/4” 24 1/2” birch
EE 2 3/4” 3/4” 13 7/8” birch
FF 1 3/4” 3/4” 23 1/2” birch
GG 3 3/4” 10 1/2” 19 3/8” birch plywwod
HH 6 1/2” 3/4” 11 1/2” birch
II 3 1/2” 3/4” 20 3/8” birch
Cutting Schedule
1/4” x 48” x 48”Birch Plywood Layout
3/4” x 48” x 96”Birch Plywood Layout
O
E
E
GG GG GG
BB
P G S
FW
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 22/203
Isometric
BB
AA
GG
II
DD
EE
FF
CC
HH
W
V
T
UX
Z
S
P
Q
R
I
C
A
E
N
M
B
J
LK
D
H
F
GO
Y
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 23/203
Side & Front Elevations
22 3/4”
11 3/4”
17”
SeeFigure 1
SeeFigure 5
SeeFigure
SeeFigure 7
SeeFigure
SeeFigure 2
SeeFigure 3
SeeFigure 4
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 24/203
Figure 2
Figure 1
Figure 3 Figure 4
TV
W
T
W
W
A
D
K
F
G
E
T
V
S
CC
HHII
EE
Location ofshelf support typ.
Location ofglass clip typ.
2
5/8”
5 5/16”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 25/203
Figure 5
Figure 7
Figure 8
Figure 6
U
X
Z
W
W
W
ZL
J G
H
M
N
O
B
K
X
U
Y
Z
X
U
HH
AA
GG HHII
FF EE
DD CCII
Center latches
on both doors
Location ofhinges typ.
2”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 26/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly Instructions
1. Assemble side panel frames (A, B, C, D) and (T, U, V), face frames (H, I, J) and (X, Y) and door frames (M, N) and (Z, AA)
Refer to Isometric and Elevations and Figures 1 through 8. Use 3/8” dowels and glue on all joints.
2. Route a 3/8” rabbet inside all side panel and door frames. Note that the corners of the rabbet are cut square in the upper cabi-
net for the glass panels (see Figures 1 and 3).
3. Locate and drill 1/4” holes for shelf supports. Refer to Elevations and Figure 2.
4. Glue panels E into lower cabinet side frames (A, B, C, D) and panel O into lower cabinet door frame (M, N).
6. Nail and glue lower cabinet sides (A, B, C, D, E) to subassembly (F, G). Refer to Isometric and Figure 4.
5. Use 1 1/4” finish nails and glue to assemble board G to board F. Refer to Isometric and Figure 4.
7. Attach lower cabinet face frame (H, I, J) to boards B using 1 1/4” finish nails and glue. Refer to Isometric and Figure 8.
8. Miter one end of boards K and both ends of board L as indicated in Isometric. Glue boards K and L to the base of the lower
cabinet. Refer to Elevations and Figures 4 and 8.
9. Use 1 1/4” finish nails and glue to assemble board S to board W. Refer to Isometric and Figure 3.
10. Nail and glue upper cabinet side frames (T, U, V) to subassembly (S, W). Refer to Isometric and Figures 1 and 3.
11. Attach upper cabinet face frame (X, Y) to boards U using 1 1/4” finish nails and glue. Refer to Isometric and
Figures 5 and 6.
13. Miter one end of boards Q and CC and both ends of boards R and DD as indicated in Isometric. Use 1” finish nails and glue
to attach R and Q to board P and CC and DD to board BB. Refer to Isometric and Figure 6.
14. Route a decorative edge on boards EE and FF (refer to Figure 6). Miter one end of boards EE and and both ends of board FF
as indicated in Isometric. Use 1” finish nails and glue to attach EE and FF to the upper cabinet.
15. Miter one end of boards HH and both ends of boards II. Attach boards HH and II to shelves GG using 1” finish nails and glue
16. Place the upper cabinet on top of the lower cabinet and paint the project.
17. Attach glass clips, hinges and door latches. Refer to Figures 1, 5 and 6. Install glass in upper cabinet.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 27/203
U-BILD
Cedar Birdhouse
Plan No. 931Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item1 5/8” x 7 1/4” x 72” cedar fence board A, B, C, D, E
1 5/8” diameter x 12” dowel F
1 7 1/4” x 11 3/4” 16 oz. copper sheet
1 box 1” finish nails
1 box #4 x 7/16” copper tacks
1 bottle wood glue
If you spend a lot of time in the yard or garden during thewarm weather, then this do-it-yourself birdhouse will make agreat summer project. Not only will the birds love it, but as itages the wood (western cedar) will turn a soft silver color andthe copper roof will acquire a handsome green patina.
The project calls for just eight pieces and is easy enough forbeginners. To build, simply cut the parts out of inexpensivecedar fencing (other wood may be substituted), cut out, sand
and assemble everything using glue and finish nails. To fin-ish, roof the projects using sheet copper and copper tacks.
The project measures about 16 inches tall by 8 inches wideby 7 inches deep.
Cutting ScheduleItem Qty T W L Material
A 2 5/8” 4” 4” cedar
B 2 5/8” 4” 12” cedar
C 2 5/8” 5 1/4” 14 5/8” cedar
D 1 5/8” 6 3/4” 5” cedar
E 1 5/8” 6 3/4” 5 5/8” cedar
F 2 3” dowels
G 1 7 1/4” 11 3/4” copper sheet
NOTES
1. Read manufacturer’s instructions before
operating equipment.
2. Always wear safety glasses.
3. We used western cedar for this project, but
redwood or sealed pine will work equally
well.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 28/203
A
A
B
B
C
C
DE
F
F
Pictorial
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 29/203
Front View
C
B B
F
F
A
DE
A
R 2
R 2
3 5/8”
2 5/8”
2 9/16”
2 9/16”
6 3/4”
2 1/2”
14 5/8”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 30/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly Instructions
1. Cut angles on one end of front and back boards (C). Refer to Front View and Pictorial.
2. Bore two 2” holes and two 5/8” holes in front board (C). Refer to Side and Front Views and Pictorial.
3. Attach sides (B) to bottom and interior boards (A) using using glue and 1” finish nails. Refer to Front View and Pictorial.
4. Attach front and back boards (C) to subassembly (A, B) using glue and 1” finish nails. Refer to Front View and Pictorial.
5. Glue dowels (F) into 5/8” holes in front board (C). Refer to Front View and Pictorial.
6. Attach roof board (D) to roof board (E) using glue and 1” finish nails. Refer to Front View and Pictorial.
7. Cut and bend copper sheet (G) to fit roof subassembly (D, E).
8. Attach copper sheet (G) to roof subassembly (D, E) using four 7/16” copper tacks spaced 1/2” in from each corner.
9. Attach roof subassembly (D, E, G) to boards (B) and (C) using glue. Refer to Front View and Pictorial.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 31/203
U-BILD
Child’s Armoire
Plan No. 766Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 1/8” x 48” x 96” hardboard M, T, U
1 1/2” x 48” x 96” plywood Q, R, S
1 1/8” x 13” x 31” pine plywood Z
47 board feet* 3/4” pine A, B, C, D, E, F, G,
H, I, J, K, L, N,
O, P, V, W, X, Y
6 pairs 16” drawer slides
8 1 1/2” wooden knobs
1 pair 3” door hinges
8 3/8” x 2” dowels
1 box 1” brads
1 box 1 1/4” finish nails
1 bottle wood glue
1 quart finish
*includes 15% scrap
Just the right size for a child’s room, this handsome
armoire project adds valuable storage space wherever it’s
used. Six roomy drawers are complemented by a big
storage cabinet that can also be used as a wardrobe for
hanging clothes.
The child’s armoire measures about 45 inches tall by
38 inches wide by 18 inches deep.
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 16 1/4” 44 1/2” pine
B 1 3/4” 16 1/8” 37 1/2” pine
C 3 3/4” 16 1/8” 17 1/4” pine
D 1 3/4” 2” 34 1/2” pine
E 1 3/4” 2” 16 1/2” pine
F 7 3/4” 2” 16 1/8” pine
G 3 3/4” 1 1/2” 15 3/8” pine
H 2 3/4” 1 1/2” 44 1/2” pine
I 1 3/4” 1 1/2” 34” pine
J 2 3/4” 1” 33” pine
K 4 3/4” 1” 15 3/4” pine
L 1 3/4” 2 1/2” 33” pine
M 1 1/8” 35 1/4” 44 1/2” hardboard
N 1 3/4” 17 3/4” 37 1/2” pine
O 1 3/4” 1 5/8” 37 1/2” pine
P 2 3/4” 1 5/8” 17 3/4” pine
Q 12 1/2” 5 5/8” 16” plywood
R 10 1/2” 5 1/4” 13 3/4” plywood
S 2 1/2” 5 1/4” 31” plywood
T 5 1/8” 14 1/4” 16” hardboard
U 1 1/8” 16” 31 1/2” hardboard
V 5 3/4” 6 3/8” 16 1/4” pine
W 1 3/4” 6 3/8” 33 1/2” pine
X 2 3/4” 2” 34 3/8” pine
Y 2 3/4” 2” 12 1/4” pine
Z 1 1/8” 12 3/4” 30 7/8” pine plywoo
NOTES1. Read all instructions and check materials before beginning
work.
2. Read manufacturer’s instructions before operating equipment.
3. Always wear safety glasses.
4. We used pine for this project, but any veneer plywood and
matching lumber (such as oak or birch) will work equally well.
5. Edge-gluing is required to achieve the necessary width of
boards A, B, C and N.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 32/203
1/8” x 48” x 96” HardboardCutting Layout
1/2” x 48” x 96” PlywoodCutting Layout
Q Q
Q
Q
Q Q
Q
S SM
U
T
T T
T TQ
Q
Q
R R R R R
R R R R R
IsometricN
G
D
P
E
F
M
BC
H
U
S
Q
A
L
T
Q
R
V
W
Z
F
I
K
O
X
Y
J
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 33/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule and layouts.
Assembly InstructionsPage One
Figure 1Boards A, D, G, M
1. Cut a 1/8” deep by 3/8” wide rabbet on the back inside
edges of side boards (A). (Note that boards (A) are mir-ror images of each other.) Refer to Figure 1 and
Isometric.
2. Attach right side board (A) to boards (B) and (C) using glue and
1 1/4” finish nails. Check for squareness. Refer to Figure 2 and
Isometric. Note: If you intend to use the cupboard as a wardrobe
for hanging clothes, eliminate center shelf (C) and refer to steps
25 and 26.
1/8”3/8”
A
G
D
M
Figure 2Boards A, B, C
2 1/2”
AB
C
20 1/2”
37 1/2”
Figure 3Face Frame (H, I, J, K, L)
6”
6”
6”
6”
6”
6”
3. Assemble face frame boards (H), (I), (J), (K) and (L) using glue.
Refer to Isometric.
H
I
H
K
K
K
K
J
J
L
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 34/203
Assembly InstructionsPage Two
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule and layouts.
4. Attach face frame (H, I, J, K, L) to subassembly (A, B, C) using glue and 1 1/4” finish nails. Refer to Isometric.
5. Attach board (D) to sides (A) using glue and 1 1/4” finish nails. Refer to Figure 1 and Isometric.
6. Attach board (E) to left side (A) and board (B) using glue and 1 1/4” finish nails. Refer to Isometric.
7. Attach boards (G) to boards (A), (D) and (J) using glue and 1 1/4” finish nails. Note that center board G is attached only to
boards (D) and (J). Refer to Figure 1 and Isometric.
9. Cut a 1/4” radius on the top front and side edges of
board (N).
8. Attach drawer slide mounting boards (F) to
boards (A) using glue and 1 1/4” finish nails.
Refer to Figure 4 and Isometric.
Figure 4Boards F
Figure 5Boards N
2 1/2”
9 1/2”
16 1/2”
23 1/2”
30 1/2”
37 1/2”AA
F F
F
F
F
F
F
R 1/4” N
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 35/203
Assembly InstructionsPage Three
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule and layouts.
10. Attach top board (N) to frame boards (D), (G) and (J) using glue and 1 1/4” finish nails. Refer to Isometric.
11. Cut a 1/4” deep by 1/8” wide dado on one side of drawer sides (Q). (Note that
half of boards (Q) are mirror images of the other half.) Refer to Figure 6.
12. Attach drawer sides (Q) to drawer fronts and backs (R) and (S) using glue and
1” brads. Refer to Figure 6 and Isometric.
13. Slide drawer bottoms (T) and (U) into dados in drawer sides (Q) and attach to
drawer fronts and backs (R) and (S) using 1” brads. Refer to Figure 6 and
Isometric.
14. Attach drawer fronts (V) and (W) using glue and 1” brads. Refer to Figure 6
and Isometric.
15. Attach drawer guides to boards (B), (F) and (Q). Refer to manufacturer’s instructions.
16. Insert cabinet back (M) into rabbets on boards (A) and attach to boards (A), (D) and (E) using 1” brads. Refer to Figure 1 and
Isometric.
17. Cut a 1/4” radius on the top front edge of trim boards (O) and (P). Refer to Figure 7.
Figure 6Drawer (Q, R/S, T/U, V/W)
Figure 7Boards (O) and (P)
1/4”
1/4”
1/8”
1/4”
3/4”
Q
V/W
R/S
T/U
R 1/4”
O/P
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 36/203
Assembly InstructionsPage Four
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule and layouts.
17. Cut a miter on one end of side trim boards (P) and attach to sides (A) using glue and 1 1/4” nails. Refer to Isometric.
18. Cut a miter on both ends of front trim board (O) and attach to board (L) using glue and 1 1/4” nails. Refer to Isometric.
19. Assemble door frame (X, Y) using glue and 3/8” by 2”
dowels. Refer to Figure 8 and Isometric.
20. Cut a 1/8” deep by 1/2” wide rabbet around the inside
edge of door frame (X,Y) using glue and dowels. Refer
to Figure 8.
21. Glue door panel (Z) into 1/8” deep by 1/2” wide rabbet
around the inside edge of door frame (X, Y). Refer to
Figure 8.
22. Attach door (X, Y, Z) to right face frame board (H) using 3” hinges. (Note that hinges are installed 4” from both ends of door.)
21. Sand and apply finish to cabinet, drawer fronts and door.
23. Attach 1 1/2” wooden knobs to drawers and door.
25. If you choose the wardrobe option for the armoire cabinet, eliminate center shelf (C)
per step 2 and install 1 3/8” clothes rod brackets centered on boards (A) and (B) and
3” below board (C). Refer to Figure 9.
26. Cut 1 3/8” clothes rod to length and install in brackets on boards (A) and (B). Refer
to Figure 9.
24. Install drawers.
Figure 8Door (X,Y, Z)
Figure 9Clothes Rod Location
Z
Y
X
9/16”
1 7/16”
1/8” deep by1/2” wide rabbet
3”
A
B
C
1 3/8” clothes rod
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 37/203
U-BILD
China SideboardPlan No. 927Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 3/4” x 48” x 48” veneer plywood C
1 3/4” x 48” x 96” veneer plywood A, B, D, E, K
9 bd. ft.* 3/4” lumber of choice F, G, H, I, J, L, M, N, O, P
22 3/8” x 1 1/2” dowels
16 5/16” x 3/4” glass clips
4 pairs 3/4” x 2” wraparound hinges8 3/16” diameter x 3/4” shelf supports
4 magnetic latches
4 1” knobs
1 box 1” finish nails
1 box 1 1/2” finish nails
1 can wood filler
1 bottle wood glue
1 quart finish of choice
*Includes 20% scrap
Combining the best features of a sideboard and a china cab-inet, this handsome china sideboard project is perfect forsmaller spaces and casual living. There’s plenty of roomfor serving on top, and dishes, serving pieces, silver andlinens are safely stored and displayed behind temperedglass doors in the cabinet below.
The project measures 60 inches long by 30 inches tall byby 15 inches deep.
NOTES
1. Read manufacturer’s instruc-
tions before operating equip-
ment.
2. Always wear safety glasses.3. We used oak for this project
but any veneer plywood and
matching lumber (such as
pine, birch or maple) will
work equally well.
Cutting Schedule
Item Qty T W L Material
I 1 3/4” 3” 46” lumber of choice
J 2 3/4” 1 1/2” 29 1/4” lumber of choice
K 1 3/4” 15” 50” veneer plywood
L 2 1/4” 3/4” 15 1/4” lumber of choice
M 1 1/4” 3/4” 50 1/2” lumber of choice
N 8 3/4” 1 1/2” 24 5/8” lumber of choice
O 8 3/4” 2” 7 7/8” lumber of choice
P 4 3/4” 1 1/2” 4” lumber of choice
Item Qty T W L Material
A 1 3/4” 13” 47 1/2” veneer plywood
B 1 3/4” 13” 26 1/4” veneer plywood
C 1 3/4” 47 1/2” 29 1/4” veneer plywood
D 2 3/4” 13 3/4” 29 1/4” veneer plywood
E 2 3/4” 12 1/2” 23 1/4” veneer plywood
F 2 1/4” 3/4” 23 1/4” lumber of choice
G 1 3/4” 2” 24 3/4” lumber of choice
H 1 3/4” 1 1/2” 46” lumber of choice
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 38/203
Pictorial
B
E
P
F
H
O
N
J
G
I
D
L
K
A
C
M
48” x 48” PlywoodCutting Layout
48” x 96” PlywoodCutting Layout
C
A B
E
E
K
D D
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 39/203
Pattern 1A Pattern 1B
A
A
Pattern 1Board D
A
A
A
A
Pattern 1A
Pattern 1B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 40/203
A A
A A
Pattern 2A
Pattern 2B
B B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 41/203
Pattern
2A
Pattern2B
Pattern2C
A A
B B
Pattern 2Board I
B B
Pattern 2C
Center
Line
Center
Line
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 42/203
1. Attach shelf trim (F) to leading edges of shelves (E) using glue and 1” finish nails. Refer to Pictorial.
2. Miter top trim boards (L) and (M) and attach to top (K) using glue and 1” finish nails. Refer to Pictorial.
5. Drill 3/16” diameter holes for shelf supports through center divider
(B). Refer to Figure 1.
6. Drill 3/16” diameter by 3/8” deep holes for shelf supports in sides (D).
Refer to Figure 2.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
B
D
Figure 2Board (D)
Figure 1Board (B)
3. Trace Pattern 1 onto sides (D), cut out curve and sand. Refer to Pattern 1 and Pictorial.
4. Trace Pattern 2 onto face frame base (I), cut out curve and sand. Refer to Pattern 2 and Pictorial.
1 1/2”
11 5/8”
11 5/8”
Back Front
2 1/4” 1 1/2”
13 1/8”
13 1/8”
14 5/8”
14 5/8”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 43/203
7. Attach center divider (B) to bottom (A) using glue and 1 1/2” finishnails. Refer to Figure 3 and Pictorial.
8. Attach back (C) to subassembly (A, B) using glue and 1 1/2” finish
nails. Refer to Figure 3 and Pictorial.
9. Attach sides (D) to boards (A) and (C) using glue and 1 1/4” finish
nails. Refer to Figure 3 and Pictorial.
10. Attach top subassembly (K, L, M) to boards (C) and (D) using glue
and 1 1/4” nails. Refer to Figure 3 and Pictorial. Note: Rear edge
of board (K) is flush with back (C).
10. Assemble face frame (G, H, I, J) using
glue and 3/8” dowels. Refer to Figure
4 and Pictorial.
11. Attach face frame (G, H, I, J) to boards
(A), (B) and (D) using glue and 1 1/4”
nails. Refer to Pictorial.
12. Assemble doors (N, O) using glue and
3/8” dowels. Refer to Figure 4 and
Pictorial.
13. Cut a 3/8” wide by 1/8” deep rabbet
around inside edges of doors (N, O).
Refer to Figure 4 and Pictorial.
14. Install hinges and glass retainer clips
on doors (N, O). Refer to Figure 4.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Figure 3Subassembly (A, B, C, D, K, L, M)
Front View, Left Side
Figure 4Face Frame (G, H, I, J) andDoor Frame (N, O) Detail
Front View
D
A
H
N
O
G
J
I
B
C
K, L, M
23 3/8”
22”
3 1/4”TYP
3/8” wide by 1/8”
deep rabbet (for
door glass)
6”TYP
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 44/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
9”
Location of magnetic
door latches
Figure 5Boards (P)
Front View, Left Side
Figure 6Door Knob Position
(TYP)
N
M
J
H P
P
O
15. Attach latch mounting boards (P) to
upper face frame board (H) usingglue. Refer to Figure 5 and Pictorial.
16. Attach magnetic latches to mounting
boards (P). Refer to Figure 5.
17. Install knobs on door stiles (N). Refer to Figure 6.
18. Sand project.
19. Apply finish of choice.
20. Install glass.
8”
3/4”
N
O
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 45/203
U-BILD
Closet OrganizerPlan No. 743Copyright U-Build, Inc., 2002.
All rights reserved. Printed in the U.S.A.
Bill of Material
Central UnitQuantity Size Material Item
3 3/4” x 48” x 96” particle board A through L
1 1/8” x 48” x 48” hardboard M1 1 3/8” diameter x 36” dowel N
3 1 1/2” diameter x 36” dowels O
1 pair 1 3/8” dowel supports
1 bottle wood glue
1 box 1 1/4” finish nails
Bill of Material
Closet Connectors(for 6’ closet as pictured)
Quantity Size Material Item
2 3/4” x 11 1/4” x 18”* particle board shelves
4 3/4” x 3/4” x 11 1/4” pine shelf supports
3 1 3/8” x 18”* dowels
3 pairs 1 3/8” dowel supports
*adjust these dimensions for a custom fit in your own closet
NOTES1. Read all instructions and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. Always wear safety glasses.
4. Use 1 1/4” finish nails and wood glue on all joints.
Cutting Schedule
Central UnitPart Qty T W L Material
A 2 3/4” 20” 78” particle board
B 2 3/4” 1 1/2” 34 1/2” particle boardC 3 3/4” 20” 34 1/2” particle board
D 1 3/4” 34 1/4” 34 1/2” particle board
E 1 3/4” 19 1/4” 34 1/4” particle board
F 3 3/4” 15 3/4” 19 1/4” particle board
G 4 3/4” 7 7/8” 15 5/8” particle board
H 8 3/4” 7 7/8” 18 1/2” particle board
I 4 3/4” 7 3/8” 14 1/8” particle board
J 1 3/4” 18” 19 1/4” particle board
K 1 3/4” 4” 18” particle board
L 1 3/4” 9 1/2” 34 1/2” particle board
M 4 1/8” 14 13/16” 18 3/4” hardboard
N 1 1 3/8” 34” dowel
O 6 1/2” 17 7/8” dowels
This closet organizer project can help any closet reach its full, unclut-
tered potential. It has compartments for suits and jackets, long coats and
dresses, shirts and blouses, pants, hats and shoes, plus four drawers for
socks and other smaller items. Built primarily from particle board, the
project is easy to set up and take down.
The closet organizer can be customized to fit a closet of almost any
size; the center unit measures 78 inches tall by 36 inches wide by 20
inches deep.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 46/203
Particle BoardCutting Layouts
E
L
H
C
A
G
G
G
G
B
A
I I I I
C C D
USE THIS SCRAP FOR ADJUSTABLE SHELVES (CLOSET CONNECTORS)
H H H H H H H K J
F F F
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 47/203
Isometric
L
C
C
F
8”TYPI
H
M
G
H
D
J
E
C
K
N
A
A
B
O
6”
1 8 ”
1 5 3 / 4 ”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 48/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Glue and nail boards B to base board C. Front board B is inset 3/4” from the leading edge of bottom board C. Back board B is
flush with the back edge of bottom board C.
Note: For steps 1 through 7 refer to Isometric.
2. Glue and nail bottom board C to board D.
3. Glue and nail middle board C to board D. Check for squareness.
4. Insert board E between bottom board C and middle board C. Glue and nail board E to boards C and D.
5. Glue and nail sides A to boards C and D. Glue and nail top board C to sides A.
6. Insert boards F between right side A and board E and glue and nail in place. Insert board J between left side A and board E and
glue and nail in place.
7. Glue and nail board L to boards A and top board C.
8. Center 1 3/8” dowel supports on sides A and attach 3” below top board C.
9. Cut and sand radius on boards G.
Refer to Figure 1.
Figure 1BOARD G
R 4 5/8”
Figure 2SECTION VIEW OF DRAWER SIDE
G
3/8”M
HH
I
10. Route a 3/8” dado on boards G and H. Refer to Figure 2.
11. Insert drawer botttom M into dados in boards G and H. Nail
in place. Refer to Figure 2.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 49/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
12. Drill six 1/2” holes in board K. Refer to Figure 3. Glue
dowels O into the holes.
13. Glue and nail board K to board D. Refer to Isometric.
Figure 3BOARD K
C
2 1/8” 2 3/4” 2 3/4”
K
A
Figure 4CLOSET INSTALLATION
Figure 5SHELF INSTALLATION
14. To install the project in a 72” closet as pictured, place the central unit in the center of the closet and anchor to the back wall
Attach pine shelf supports to sides A and side walls of closet and install 18” shelves. Attach 1 3/8” dowel supports to sides A
and side walls of closet and install 18” dowels. Refer to Figures 4 and 5.
18”
72”
CENTRAL UNIT
SHELF
SHELF SUPPORT
SIDE A/ CLOSET
WALL
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 50/203
U-BILD
Curio Table
Plan No. 854Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Qty Size Material Item
1 3/4” x 48” x 96” oak plywood D, G, H, P, Q
1 1/2” x 48” x 48” oak plywood R
1 1 1/2” x 1 1/2” x 150” oak A, B, E
1 1 1/2” x 2” x 110” oak C, F, J
9 bd. ft. 3/4” oak I, K, L, M, N, O, S
48 3/8” x 1” oak dowels
4 1 1/2” wood knobs
1 1/4” x 17 5/8” x 31 5/8” tempered glass
16 3/8” flat plugs
16 1” coarse drywall screws
1 box 1” finish nails
1 box 1 1/4” finish nails
1 bottle wood glue
1 can oak wood filler
1 quart stain
1 quart finish of choice
Cutting Schedule
Item Qty T W L Material
A 4 1 1/2” 1 1/2” 16 1/4” oak
B 2 1 1/2” 1 1/2” 19” oak
C 2 1 1/2” 2” 19” oak
D 2 3/4” 11 1/2” 19 3/4” oak plywood
E 1 1 1/2” 1 1/2” 33” oak
F 1 1 1/2” 2” 33” oak
G 1 3/4” 11 1/2” 33” oak plywood
H 1 3/4” 19” 33” oak plywood
I 2 3/4” 1 1/2” 33” oak
J 1 1 1/2” 2” 33” oak
K 4 5/16” 3/4” 19 1/2” oak
L 1 3/4” 7/8” 33” oak
M 2 3/4” 7/8” 18 1/8” oak
N 2 3/4” 3 1/4” 37 1/2” oak
O 2 3/4” 3 1/4” 17” oak
P 4 3/4” 5 1/8” 19 3/4” oak plywood
Q 4 3/4” 4 1/8” 31 3/8” oak plywood
R 2 1/2” 32” 19 3/4” oak plywood
S 2 3/4” 5 3/16” 32 7/8” oak
If you like to collect things, this handsome curio coffee table
can help ease the storage crunch. The project is topped with a
piece of heavy glass with a drawer underneath that provides
almost four square feet of display space.
The curio table measures about 38 inches long by 24 inches
deep by 17 inches tall.
NOTES• Read manufacturer’s instructions before operating equipment.
• Always wear safety glasses.
3/4” x 48” x 96” Oak Plywood
Cutting Layout
D
HG
P
P
Q
Q
Q
Q
P
P
D
1/2” x 48” x 48” Oak Plywood
Cutting Layout
RR
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 51/203
Isometric(Note: Board F not shown)
N
E
N
LK
O
G
H
M
I
A
N
I
J
B
D
AC
C
R
S
SQ
Q
P
D
1/4”GLASS
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 52/203
Figure 1Curio Coffee Table Cross Section
O
B
K
D
P
Q
R
C
J
A
S
G
I
Location of six 1”
drywall screws typ.
Location of
knobs typ.
H
M
N
I L
E
1/4”GLASS
3 7/8”
12 7/16”
9 3/8”
6 5/16”
2”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 53/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Attach boards (A) to boards (B) and (C) using glue and dowels. Refer to Isometric and Figure 1.
2. Rout a 3/8” by 3/4” deep rabbet around inside edges of side subassemblies (A, B, C). Radius the corners of boards (D) and glue
in place. Refer to Isometric and Figure1.
3. Rout a 3/8” by 3/4” deep rabbet on one edge of boards (E) and (F). Glue (E) and (F) to board (G). Refer to Figure 2.
4. Attach subassembly (E, F, G) and upper board (I) and board (J) to sides (A, B, C, D) using glue and dowels. Refer to Isometr
and Figures 1 and 2. Note: Do not install lower board (I) at this time (see Step 5).
Figure 2Boards (E), (F), (G), (N), (O)
F
N
E
G
O
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 54/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
5. Glue board (I) to board (H). Use 1 1/4” finish nails and glue to attach subassembly (H, I) to boards (D) and (G). Refer to Figure
1 for location.
6. Rout an optional decorative 1/4” cove around inside edges of boards (A), (B), (C), (E) and (F). Stop the cove 1” from the ends
of each board. Refer to Isometric and Figure 2.
7. Rout a 1/4” radius on outside corners of boards (A). Refer to Isometric.
8. Attach drawer rails (K) to boards (D) using 1” finish nails and glue. Refer to Isometric and Figure 1.
9. Glue board (L) to board (E) and boards (M) to boards (B). Refer to Isometric and Figure 1.
10. Attach boards (N) to boards (O) using glue and dowels. Refer to Isometric and Figure 1.
11. Rout a 1/4” radius around the outside edges of boards (N) and (O). Refer to Isometric and Figure 1.
12. Attach top frame (N, O) to the table base using glue and 1” drywall screws. Countersink and cover the screws with 3/8” plugs
Refer to Isometric and Figure 1.
13. Rout a 1/4” deep by 3/8” wide rabbet on the inside edges of top frame (N, O) to accommodate the glass. Refer to Isometric and
Figure 1.
14. Rout a 3/8” deep by 13/16” wide dado down the center of one side of boards (P). Rout a 3/8” deep by 1/2” wide dado on the
opposite side of boards (P) to accommodate drawer bottoms (R). Refer to Isometric and Figure 1.
15. Assemble boards (P) to boards (Q) using glue and 1 1/4” finish nails. Slide drawer bottoms (R) into the grooves on boards (P)
Attach (R) to (Q) using 1 1/4” finish nails. Refer to Isometric and Figure 1.
16. Attach drawer fronts (S) to boards (Q) using six 1” drywall screws. Space the screws 1 1/2” from the ends of the drawers and
1” from the top and bottom edges. Countersink and cover the screws with 3/8” plugs. Refer to Isometric and Figure 1.
17. Attach knobs to drawer fronts (S). Refer to Figure 1.
18. Stain and finish project.
19. Cut glass to fit and place in rabbet on top frame (N, O).
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 55/203
U-BILD
Display CabinetPlan No. 865Copyright U-Build, Inc., 1997.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 3/4” x 48” x 96” oak plywood A, B, C, D, E
4 board feet 3/4” oak F, G, H, I,
J, K, L, M
1 3/16” x 24” x 24” oak plywood N
1 1 1/16” x 1 1/4” x 60” oak molding P, Q
2 1/8” x 11 3/8” x 17 1/8” tempered glass
9 3/8” x 1” dowels
2 1” knobs
2 pairs 1 1/2” cabinet hinges
8 5/16” x 3/4” glass clips
2 magnetic latches
1 box 1” finish nails
1 box 1 1/2” finish nails
1 bottle wood glue
1 small can oak wood filler
1 quart finish
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 7 3/4” 21 3/8” oak plywood
B 1 3/4” 7 1/4” 28” oak plywood
C 2 3/4” 6 1/4” 28” oak plywood
D 1 3/4” 7 3/4” 28” oak plywoodE 1 3/4” 28” 20 3/8” oak plywood
F 1 1/4” 3/4” 28” oak
G 2 1/4” 3/4” 28” oak
H 4 1/4” 3/4” 7 3/4” oak
I 2 1/4” 3/4” 21 7/8” oak
J 1 3/4” 2” 28” oak
K 1 3/4” 1 1/4” 19 1/8” oak
L 4 3/4” 1 1/4” 19” oak
M 4 3/4” 1 1/4” 10 3/4” oak
N 2 3/16” 11 1/2” 17 1/4” oak plywood
O 2 3/4” 1 1/4” 6” oak
P 1 1 1/16” 1 1/4” 31 5/8” oak molding
Q 2 1 1/16” 1 1/4” 9 1/16” oak molding
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keep-
ing it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet's design calls for all straigh
cuts and straightforward construction techniques (simple cut-outs give the effect of multiple panes of glass in the single-pane doors).
Finish is up to the builder, so the project will match any decor.The display cabinet measures about 32 inches wide by 22 inches tall by 9 inches deep, and the shelves are each about 7 inches deep
NOTES
1. Read all instructions and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. Cut all wood to exact size. Follow the cutting schedule.
4. Always wear safety glasses.
5. Use wood glue on all joints.
6. Drill pilot holes in oak before nailing.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 56/203
B
E
G
C
D
L
TEMPEREDGLASS
MN
K
F
A
I
O
J P
QH
Isometric
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 57/203
2. Use 1 1/2” finish nails and glue to attach boards C to E. Make sure that the boards line up square.
Refer to isometric and Figure 3 for location.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Use 1” nails and glue to attach boards H and I to boards A. Attach G to C and F to D in the same manner.
Refer to Figures 1 and 2 and isometric.
3. Use 1 1/2” finish nails and glue to attach boards B and D to E.
4. Use 1 1/2” finish nails and glue to attach boards A to B, C, D and E. Refer to Figures 1 and 2.
Figure 1 Figure 2(Note: Part “P” is not shown.)
Figure 3
I
A
F
Q
H
B
J
I
M
L
E
C
C
D
H
6 1/4
12
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 58/203
6. Use 3/8” x 1” dowels and yellow glue to attach boards K to J. Use the same procedure for door frame.
7. Use 1 1/2” finish nails and glue to attach J and K to A, B and D. Refer to isometric.
5. Drill a 3/8” hole in boards M and L
for 1” dowel. Refer to Figures 4 and5. Drill a 3/8” hole is boards J and
K. Refer to Figure 6.
Figure 5
Figure 6
Figure 4
M
L2
1 1/2
3/8 x 5/16 RABBET
3/8 x 1 DOWEL
GLASS CLIP
MAGNETIC LATCH
1/8 TEMPERED GLASS
N
J
B
O
M
LK
L
M3/8 x 1 DOWEL
GLASS CLIP
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 59/203
12. Rout a 3/8” x 5/16” deep rabbet on the inside edge of door L and M. Refer to Figures 4 and 5.
13. Apply finish at this time. Locate knobs in the middle of board L. Attach hinges and glass supports. Insert panel N and glass
Attach two magnetic latches to board O for doors. Refer to Figures 4, 5 and 6.
9. Glue two O boards to the inside face of board J. Refer to Figure 6 and isometric.
10. Cut and attach molding P and Q. Use 1” finish nails and glue. Refer to Figure 2 and Isometric.
11. Cut a small gain in board L door frame to accommodate hinges. The depth of the gain will be determined by the size of the hinge
and the amount of clearance around the door.
8. Drill a large hole in one of the pan-
els. Use a jigsaw or scrollsaw tocut out the six openings in board N.
Refer to Figure 7.
Figure 7
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
1/2
4 7/8
4 7/8
N
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 60/203
U-BILD
FootbridgePlan No. 896Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
2 1 1/2” x 5 1/2” x 120” lumber of choice A, B8 1 1/2” x 3 1/2” x 96” lumber of choice C, D
2 1 1/2” x 3 1/2” x 144” lumber of choice F
3 3 1/2” x 3 1/2” x 96” lumber of choice E
120 #10 x 2 1/2” flat head wood screws
12 3/8” x 5 1/2” carriage bolts
12 3/8” nuts
12 3/8” washers
1 quart finish of choice
Like a gazebo or an arbor trellis, a footbridge is one ofthose garden structures that helps transform a plain back-yard into a charming and livable outdoor space. Now do-it-yourselfers with a weekend to spare can add a footbridgeto their own yard or garden with this easy project.
The proportions of this footbridge make it an idealaccent for a garden path or an ornamental dry creek. Andif it's in the right place, it may even keep your feet dry.
The footbridge measures six feet long by 30 inches wideby 40 inches tall.
Cutting Schedule
Item Qty T W L Material
A 2 1 1/2” 5 1/2” 27” lumber of choice
B 2 1 1/2” 5 1/2” 72” lumber of choice
C 2 1 1/2” 3 1/2” 30” lumber of choice
D 20 1 1/2” 3 1/2” 30” lumber of choice
E 6 3 1/2” 3 1/2” 40” lumber of choice
F 4 1 1/2” 3 1/2” 72” lumber of choice
NOTES
1. Read manufacturer’s instructions before oper-
ating equipment.
2. Always wear safety glasses.
3. We used redwood for this project, but cedar or
treated lumber (painted) will work equally
well. Make sure that lumber has a low mois-
ture content to minimize shrinkage.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 61/203
Pictorial
B
EF
D
AC
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 62/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 1Post (E) Detail
Figure 2(A, B, C, D, E) Detail
2. Sand and apply finish to boards (A), (B), (C), (D), (E) and (F). Allow to dry thoroughly.
1. Cut optional decorative detail on top end of posts (E). Refer to
Figure 1. (Note: Project is pictured with prefabricated post caps,
which may be substituted. Attach using glue and finish nails.)
3. Attach base sides (B) to base ends (A) using 2 1/2”
wood screws. Check for squareness. Refer to
Figure 2 and Pictorial.
4. Attach boards (C) to both ends of bottom of base
sides (B) using 2 1/2” wood screws. Check for
squareness. Refer to Figure 2 and Pictorial.
5. Attach boards (D) to the top of base sides (B) using
2 1/2” wood screws. Check for squareness. Refer
to Figure 2 and Pictorial.
BA
C
D
E
E
30
1 1/2”
3/4”TYP.
1”
1/2”
3/8”
3/4”TYP.
1 1/4” TYP.
1 1/2” TYP.
3 1/2” TYP.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 63/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Figure 4Rail (F) Detail
6. Attach posts (E) to base sides (B) using 3/8” x 5 1/2” carriage bolts. Drill countersink large enough for washers and deep enough
so that bolt head is flush with outside surface of post (E). Refer to Figures 2 and 3 and Pictorial.
7. Attach rails (F) to posts (E) using 2 1/2” wood
screws. Check for squareness. Refer to Figures 3
and 4 and Pictorial.
F
E
1”TYP.
1”TYP.
Figure 3Post (E) and Rail (F) Locations
BA
C
D
E
F
29 1/2”
16”
30”6” 6”30”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 64/203
U-BILD
Hall TreePlan No. 934Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
5 3/4” x 6” x 96” lumber of choice B, E, G, H, I, J, K, L,
M, N, O, P, Q, R, T, U
2 3/4” x 48” x 96” plywood A, C, D, F, S
1 pair 2 1/2” x 1 3/4” butt hinges
4 coat hooks1 box 1” finish nails
1 box 1 1/4” finish nails
1 box 1 1/2” finish nails
1 bottle wood glue
1 can wood filler
1 quart primer
1 quart paint
Perfect for the entryway, living room or even one end of the dining room, this handsome hall tree features a con-venient place to hang coats, hats and umbrellas over agenerously sized storage bench.
Made from straight cuts of standard lumber and ply-wood, the project is easy enough for woodworkers of anyskill level.
The hall tree measures about 70 inches tall by 45 inch-
es wide by 21 inches deep.
Cutting Schedule
Item Qty T W L Material
L 2 3/4” 2 1/2” 9 3/4” lumber of choice
M 2 3/4” 3/4” 6” lumber of choice
N 1 3/4” 5” 44 1/2” lumber of choice
O 1 3/4” 4 1/2” 41 1/2” lumber of choice
P 4 3/4” 2 1/2” 47 3/4” lumber of choice
Q 6 3/4” 2 1/2” 10 1/2” lumber of choice
R 1 3/4” 3 3/4” 44 1/2” lumber of choice
S 1 3/4” 15 1/4” 43 3/4” plywood
T 2 3/8” 3/4” 15 1/4” lumber of choice
U 2 3/8” 3/4” 44 1/2” lumber of choice
Item Qty T W L Material
A 2 3/4” 18 3/4” 14 3/8” plywood
B 2 3/8” 3/4” 18 3/4” lumber of choice
C 1 3/4” 18 3/4” 40” plywood
D 1 3/4” 41 1/2” 14 3/8” plywood
E 1 3/8” 3/4” 41 1/2” lumber of choice
F 1 3/4” 41 1/2” 69 1/4” plywood
G 2 3/4” 2 1/2” 69 1/4” lumber of choice
H 2 3/4” 1 3/4” 16 1/4” lumber of choice
I 4 3/4” 2 1/2” 16” lumber of choice
J 2 3/4” 2 1/2” 16 1/4” lumber of choice
K 2 3/4” 2 1/2” 38” lumber of choice
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 65/203
3/4” x 48” x 96”Plywood Cutting Layouts
D
S
C A A
F
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. Drill pilot holes when using screws or finish nails to attach one board to another.
4. We used poplar and birch for this project, but oak or pine will work equally well.
5. We painted our project, but the builder may choose another finish.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 66/203
PictorialNote: Bottom (C) not shown
R
O
P
Q
G
G
F
Q
Q
Q
Q
QN
SB
B
P
P
P
L
D
K
K
J
J
H
A
I
I
F
L
EU
T
M
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 67/203
Front View Side View
Top View
9 1/2” TYP.
6”TYP.
G
I
A
H
J K L
R R
O
G
F
Q
G
G
N UM
G
DK
P
NTS
U
F
M
J
F
C
D
CK
LD
FM P Q
U
T
U
N
C
3/4”TYP.O
F
Q
P P P P
A
H
I
I
G
G
G
Q Q
Q
F
L L
K
D
J
K
Q
S
R
10 1/2”TYP.
16 1/4” TYP.
5 1/4” TYP.
1 1/2”
UE
10 1/2” TYP.
11”TYP.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 68/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 1
Board N
1. Attach trim boards (B) to top edges of sides (A) using glue and 1” finish nails. Refer to Pictorial.
2. Attach side assemblies (A, B) to bottom (C) using glue and 1 1/2” finish nails. Check for squareness. Refer to Top and Side
Views.
3. Attach trim board (E) to top edge of front board (D) using glue and 1” finish nails. Check for squareness. Refer to Side View.
4. Attach front assembly (D, E) to box assembly (A, B, C) using glue and 1 1/2” finish nails. Check for squareness. Refer to
Pictorial and Front, Side and Top Views.
5. Attach back (F) to box assembly (A, B, C, D, E) using glue and 1 1/2” finish nails. Note that back (F) should extend 1 1/2” past
the bottom of the box to form the project’s rear legs. Refer to Pictorial and Front, Side and Top Views.
6. Attach boards (G) and (H) to box and back assembly (A, B, C, D, E, F) using glue and 1 1/4” finish nails. Refer to Pictorial and
Front, Side and Top Views.
7. Attach boards (I) each side of box assembly using glue and 1 1/4” finish nails. Refer to Pictorial and Side and Top Views.
8. Attach boards (J), (K) and (L) to front of box assembly using glue and 1 1/4” finish nails. Refer to Pictorial and Front View.
11. Attach board (N) to box assembly using glue and 1 1/2” finish nails. Refer to Pictorial and Front, Side and Top Views.
9. Attach boards (M) to front side of back panel (F) using glue and 1 1/4” finish nails. Refer to Pictorial and Front, Side and Top
Views.
10. Cut notch and gain in both ends of board (N).
Refer to Figure 1.
6”TYP.
1 1/2”TYP.
1 3/4” TYP.
R 1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 69/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
12. Place project on its back and attach board (O) to top of back (F) using glue and 1 1/4” finish nails. Refer to Pictorial and Front
and Side Views.
13. With project still on its back, attach boards (P) and (Q) to back (F) using glue and 1 1/4” finish nails. Refer to Pictorial and Front
View.
14. Stand project up and attach board (R) to boards (G) and (O) using glue and 1 1/2” finish nails. Refer to Pictorial and Front, Side
and Top Views.
15. Attach trim boards (T) and (U) to edges of seat (S) using glue and 1” finish nails. Refer to Pictorial and Top View.
16. Cut gains for hinges in back edge of seat (S) using board (N) as a reference.
17. Sand and apply finish of choice to the project.
18. Install hinges and attach seat (S, T, U) to project.
19. Attach coat hooks to boards (P). Refer to Front View.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 70/203
U-BILD
Hammock
FramePlan No. 868
Copyright U-Build, Inc., 1997.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
5 2” x 6” x 12’ Straight Grain Douglas Fir A, B, C, D
1 2” x 8” x 8’ Straight Grain Douglas Fir E
2 2” x 4” x 8’ Straight Grain Douglas Fir F
2 1/2” x 8” Eye Bolts
14 1/2” x 4 1/2” Carriage Bolts
8 1/2” x 3” Carriage Bolts
20 1/4” x 3 1/2” Lag Bolts
26 1/2” Flat Washers
20 1/4” Flat Washers
26 1/2” Nuts
1 gallon Waterproof Finish
Cutting Schedule
Part Qty T W L Material
A 2 1 1/2” 5 1/2” 144” Straight Grain Douglas Fir
B 2 1 1/2” 5 1/2” 59 1/2” Straight Grain Douglas Fir
C 2 1 1/2” 5 1/2” 83” Straight Grain Douglas Fir
D 4 1 1/2” 5 1/2” 23 1/2” Straight Grain Douglas Fir
E 2 1 1/2” 7 1/4” 48” Straight Grain Douglas Fir
F 4 1 1/2” 3 1/2” 41 1/16” Straight Grain Douglas Fir
A good book, a tall glass of iced tea and the gentle swaying motion of a shady hammock on the patio, next
to the pool or in the yard-sounds like paradise, doesn't it? With a few basic tools and some inexpensive
materials, any do-it-yourselfer with a free weekend can create a place to relax and catch a few winks.This easy-to-build hammock frame project calls primarily for straight cuts and requires only basic con-
struction techniques.
Made entirely of straight-grain Douglas fir, the frame is not only sturdy, comfortable and safe, but it's
attractive enough to blend nicely with any landscaping.
Designed to fit a standard-size hammock sling, the completed project measures 16 feet long by 4 feet
wide.
NOTES
1. Read all instructions and check materials befo
beginning work.
2. Read manufacturer’s instructions before operati
equipment.
3. Cut all wood to exact size. Follow the cutting sche
ule.
4. Always wear safety glasses.
5. Use only straight grain lumber for your hammo
frame project. Do not use any boards that ha
checks, splits, knots or defects.
6. When drilling the 1/2” holes in board B to hold t
eye hook, great care should be taken to ensure th
the hole is parallel to the face.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 71/203
A
C D
B
E
F
E
A
A
A
C
D
B
AC
F
B
E
D
F
Section A-ACONSTRUCTION
DIAGRAMS
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 72/203
2. Use a jigsaw to cut angles and radii on all boards. Check the isometric for the location of all the joints and route all exposed edges
with a 3/8” radius bit.
3. Drill a 1 1/8” hole 1/4” deep on the top edge of board B. Drill a 1/2” hole through the rest of board B. See Figures 1 and 2. Note
The 1/2” hole must be parallel to the face of the board to ensure proper strength.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Cut all boards to the proper size. Refer to the cutting schedule and Figures 1 through 7.
Figure 2BOARD B
Figure 1BOARD B
56 3/4
1/2 TYP.
1 1/2
1/2
1 1/8
R 2 3/4
53 1/2
47 5/16
1 11/16
4 1/4
5 1/2
5 5/8
4 1/8
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 73/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
4. Locate and drill 1/2” holes in boards as shown in Figures. Countersink eight 1 1/8” by 1/2” deep holes on one side of one of the
A boards. Countersink two of the D boards and all of the F boards for washers and nuts. Refer to Figures 3, 4 and 5.
Figure 3BOARD A
Figure 4BOARD F
Figure 5BOARD D
72
49
45 3/8
1/2 TYP.
1 1/8 COUNTERSINK ON ONE SIDE OF ONEOF THE A BOARDS (TYP. BOTH ENDS)
2 3/4
41 1/16
7 3/8
1 1/8 COUNTERSINK TYP.
1 1/8 COUNTERSINK TWO OF THE D BOARDS TYP.
1/2 TYP.1/4 TYP.3/8
3/4
7/8
2 3/8
R 2 3/4
1/2 TYP.2 3/4
4 1/2
10 1/2
20 3/4
5 1/2
60o
150o
60o
60o
1 3/4
3 1
3
5 1/2
6
3
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 74/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
10. Drill six 1/4” holes in board E. Attach E to A using six 1/4” by 3 1/2” lag bolts and washers. Refer to Figure 6.
11. Insert two 3” carriage bolts through board E into F. Use one washer and nut for each bolt. Drill two 1/4” holes in the top
of board F. Use two 1/4” by 3 1/2” lag bolts and washers to attach board F to D. Refer to Figure 4.
Figure 6BOARD E
6. Use 2 1/2” drywall screws to temporarily hold board D to B and C.
7. Bolt board D to B and C. Use 4 1/2” carriage bolts.
8. Insert the 1/2” by 8” eye bolts and washers into board B. Use a washer and two 1/2” nuts as jam nuts to secure eye bolt.
9. Tighten bolts on board A.
5. Use a scrap piece of plywood cut at a 60 degree angle to align board B to board A. Use four 1/2” by 4 1/2” carriage bolts to attach boards A to B and C. Refer to Figures and isometric.
R 60
2 3/4
4 7/16
4 5/8
1 3/4
5 1/2
7 1/4
6 13/16
9 5/8
24
1/4 TYP.
1/2 TYP.
1
1 1/2
R 2 3/4
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 75/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
Figure 7BOARD C
8315 5/16
1/2 TYP.
9 5/16
2 3/4
11 13/16
8 11/16
1 13/16
3 5/8
5 1/2
30o30o
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 76/203
U-BILD
Hope Chest
Plan No. 885Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 3/4” x 48” x 48” pine plywood E, F
1 1/2” x 48” x 48” mahogany* plywood L, M, N
1 1/2” x 24” x 48” Douglas fir plywood D
16 bd. ft. 3/4”
lumber of choice A, B, C, G, H,I, J, K, O
16 3/8” x 2” dowels**
1 pair 18” full-extension
drawer slides
1 pair 2” butt hinges
2 1” knobs
1 lid support
1 box 1” finish nails
1 box 1 1/2” finish nails
birch plugs
1 can wood filler
1 bottle wood glue
1 quart finish of choice
*This plywood may be labelled “luan”
**Biscuits may be substituted for dowels
Cutting Schedule(Some boards may require edge-gluing to achieve width)
Item Qty T W L Material
A 4 3/4” 3” 23 1/4” pine
B 2 3/4” 3” 14” pine
C 2 3/4” 3” 14” pineD 2 1/2” 14 3/4” 17” Douglas fir plywood
E 1 3/4” 22 1/4” 33 1/2” pine plywood
F 1 3/4” 19” 33 1/2” pine plywood
G 1 1/4” 3/4” 33 1/2” pine
H 1 3/4” 10 1/2” 33 1/2” pine
I 1 3/4” 3” 33 1/2” pine
J 1 3/4” 3” 36” pine
K 1 3/4” 18” 36” pine
L 2 1/2” 7 5/8” 18 1/4” mahogany plywood
M 2 1/2” 6 5/8” 31 1/2” mahogany plywood
N 1 1/2” 18 1/4” 32” mahogany plywood
O 1 3/4” 7 7/8” 33 3/8” pine
A perfect marriage of form and function, this tradi-
tional hope chest is as useful in the den, dining room
or hall as it is in the bedroom. The project is great for
extra linens, but the large storage compartment and
generous drawer work just as well for games, CDs
DVDs, scarves and mittens, table linens or almost
anything else. And the handsome Craftsman style
complements any decor.
The hope chest measures 36 inches long by 24
inches tall by 21 inches deep.
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. Use glue and 1 1/2” finish nails on all joints unless otherwise noted.
4. We used pine for this project, but any veneer plywood and matching lumber (such as oak, birch or maple) will work
equally well.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 77/203
Plywood Cutting Layouts
1/2” x 24” x 48”
Douglas fir plywood
3/4” x 48” x 48”
Pine plywood
1/2” x 48” x 48”
Mahogany plywood
D
K
D
E F
N
M
M
L L
D
EF
H
L
N
M
O
GB
D
A
C
I
J
B
A
C
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 78/203
1. Lay out and cut curves on boards (C), (E) an (I). Refer to Figures 1 and 2.
2. Attach board (G) to board (F) using glue and 1” finish nails. Refer to
Figure 3.
3. Attach board (E) to board (F) using 1 1/2” finish nails. Refer to Figure3.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 1Board (C) Curve Layout
C
R 13”
3”
15/16”
Figure 3Subassembly (E, F, G)
G
E
F
10 1/2”
Figure 2Board (E) and (I) Curve Layout
E & I
R 83 7/16”
3”
15/16”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 79/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
4. Drill 3/8” holes in boards (A), (B) and (C). Refer to Figure 4.
5. Assemble side frame subassemblies (A, B, C) using glue and 3/8”
dowels. Refer to Figure 4 and Isometric.
6. Route a 1/2” deep by 3/8” wide rabbet on the inside edges of side
frame subassemblies (A, B, C). Refer to Figure 4.
7. Glue side panels (D) into rabbets in side frame subassemblies (A,
B, C). Refer to Figure 4 and Isometric.
8. Attach sides (A, B, C, D) to subassembly (E, F) using glue and 1 1/2” finish nails. Refer to Isometric.
9. Attach front base board (I) to boards (A) using glue and 1 1/2” finish nails.
Refer to Figure 5 and Isometric.
Figure 4Subassembly (A, B, C, D)
Figure 5Relative Position ofBoards (A) and (I)
1”
1”
A
A
I
C
D
B
1/2” x 3/8”
rabbet
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 80/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
10. Attach front panel (H) to boards (A) and (F) using glue and 1 1/2” finish nails. Note that board (H) is inset 1/4” from the out-
side edges of boards (A) and (G). Refer to Isometric.
11. Attach top board (J) to boards (A) and (E) using glue
and 1 1/2” finish nails. Refer to Figure 6 and Isometric.
12. Attach top (K) to board (J) using butt hinges. Refer to Isometric.
15. Install drawer (L, M, N, O) following drawer slide manufacturer’s instructions. Refer to Isometric.
13. Cut a 1/4” deep by 1/2” wide dado in drawer
sides (L). Refer to Figure 7.
14. Assemble drawer (L, M, N, O) using glue and
1” finish nails. Refer to Figure 7 and
Isometric.
1/2”
1/2”
J
A
E
Figure 6Relative Position of
Boards (A), (E) and (J)
1/4”
1/16”
7/16”
1/2”
L
N
O
M
Figure 7Relative Position of
Boards (L), (M), (N) and (O)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 81/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
17. Install drawer knobs.
16. Apply finish of choice.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 82/203
U-BILD
Jewelry BoxPlan No. 906Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of MaterialQuantity Size Material Item
1 3/4” x 6” x 6’ Maple A, B, D
1 3/8” x 6” x 6’ Maple C, G, H,
I, J, K
1 1/2” x 3/4” x 5’ Maple Molding E, F
1 Pair 1 1/2” Butt Hinges
1 Small Box Lock
1 Small Bottle Wood Glue1 Pint Finish
Cutting SchedulePart Qty T W L Material
A 2 3/4” 4 1/4” 8 1/4” Maple
B 2 3/4” 4 1/4” 12” Maple
C 1 3/8” 7 1/2” 10 1/2” Maple
D 1 3/4” 9” 12” Maple
E 2 1/2” 3/4” 10” Maple
F 2 1/2” 3/4” 13” Maple
G 2 3/8” 1 3/4” 7” Maple
H 2 3/8” 1 3/4” 10 3/8” Maple
I 1 3/8” 6 5/8” 9 5/8” Maple
J 1 3/8” 1 3/8” 6 5/8” Maple
K 2 3/8” 1 1/2” 7 1/2” Maple
Even costume jewelry shines when it’s housed in an elegant,
handcrafted jewelry box. That’s what makes this jewelry box
project ideal for any collection. Made of maple for it’s beauty and
durability, the box features a lock for security and a convenient lift-out tray.
Utilizing all straight cuts and simple joinery techniques, the jewelry box is a good project for beginners. Just cut the
pieces to size, assemble, finish and install the hardware. The inside may be flocked or lined, or simply finished like the
outside.The completed jewelry box measures 13 inches wide by 10 inches deep by 5 inches tall.
NOTES1. Although maple is preferred for this project, other
wood may be substituted.
2. You may add more partitions to or relocate board (J) in
the removable tray.
4. Read manufacturer’s instructions before operating
equipment.
3. Always wear safety glasses.
G H
A
K
C
B
D
B A
E
FE
F
I
H G
J
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 83/203
1. Read all instructions before beginning any work.
2. Cut all material to sizes shown in cutting schedule. (This is a good time to cut out the area for installing a lock
3. Glue and clamp boards (B) to boards (A). Check assembly for squareness.
4. Glue the bottom of the box (C) to assembly (A, B).
5. Glue and clamp boards (G) to boards (H). Check assembly for squareness. Glue the bottom of the box (I)
assembly (G, H).
6. Install board (J) with glue to tray assembly. Cut tray supports (K) to fit box assembly.
7. Cut 45 degree miter on molding pieces (E) and (F) and glue to box.
8. Sand, apply finish and install hardware.
Assembly Instructions
A
GH
D
D1
3/16 TYP
3/8 TYP
B
C
E
I
H
G
3
E
A
J
K
A
G
B
F
H
B
F
K
C E
I
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 84/203
U-BILD
Lawyer’s Bookcase
Plan No. 700Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material*
Quantity Size Material Item8 3/4” x 6” x 120”** oak A, B, D, E, F
H, I, J, K
1 1/4” x 48” x 96” oak plywood C
36 3/8” x 1” dowels
16 3/8” x 1 1/2” dowels
1 1/8” x 8 5/8” x 42 7/8” tempered glass
2 1/8” x 10 5/8” x 42 7/8” tempered glass
1 1/8” x 12 5/8” x 42 7/8” tempered glass
4 1 1/4” wooden knobs
16 glass clips4 magnetic latches
1 box 1 1/4” finish nails
1 box 1/2” brads
1 bottle wood glue
1 quart finish of choice
1 tube silicon caulking (optional)
*For project as pictured; (1) 16” case, (2) 14” cases, (1) 12” case
**Roughly 40 board-feet.
As common in law offices today as they were 100 years ago, traditiona
lawyer’s bookcases are designed for storing expensive law books.
Traditionally made of oak, the style is characterized by individual stacking
compartments, or cases, fronted by glass doors. The doors allow for total
visibility while protecting each case’s contents from dust and dirt.
This do-it-yourself version shares the classic features of the originals,
making it ideal for displaying books or almost anything else. Like the orig-
inals, the project is built one case at a time (following the same steps each
time) and stacked.
The completed lawyer’s bookcase measures five feet tall by four feet
wide by one foot deep. As pictured, the bottom case measures 16 inches
tall, the top one is 12 inches tall and the two middle cases are 14 inches tall
but the combination is up to the builder.
NOTES1. Read all instructions and check materials before
beginning work.
2. Read manufacturer’s instructions before operat-
ing equipment.
3. Always wear safety glasses.
4. We used oak for this project, but any veneer ply-
wood and matching lumber (such as cherry,
pine or birch) will work equally well.
5. When using finish nails on oak, drill pilot holes
to avoid splitting.6. Edge-gluing is required to achieve the necessary
width of boards A, B and H (see cutting sched-
ules).
7. Accuracy in layout, cutting and construction is
critical in allowing the units to fit together prop-
erly and the doors to pivot and slide as designed
Check squareness of components as you build.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 85/203
Cutting Schedule--Top
Item Qty T W L Material
H 1 3/4” 11” 45 1/2” oak
I 2 3/4” 1 1/2” 11 5/8” oak
Cutting Schedule--Base
Item Qty T W L Material
J 2 3/4” 3” 45 1/2” oak
K 2 3/4” 3” 11 5/8” oak
Cutting Schedule--12” Case
Item Qty T W L Material
A 1 3/4” 11” 48” oak
B 2 3/4” 11” 11 5/8” oak
C 1 1/4” 11 1/2” 46” oak plywood
D 2 3/4” 5/8” 12” oak
E 2 3/4” 1 1/2” 11 1/8” oak
F 2 3/4” 1 1/2” 42 3/8” oak
G* 1 1/8” 8 5/8” 42 7/8” tempered glass
*Cut glass to fit after door frame is built.
Cutting Schedule--14” Case
Item Qty T W L Material
A 1 3/4” 11” 48” oak
B 2 3/4” 11” 13 5/8” oak
C 1 1/4” 13 1/2” 46” oak plywood
D 2 3/4” 5/8” 14” oak
E 2 3/4” 1 1/2” 13 1/8” oak
F 2 3/4” 1 1/2” 42 3/8” oak
G* 1 1/8” 10 5/8” 42 7/8” tempered glass
*Cut glass to fit after door frame is built.
Cutting Schedule--16” Case
Item Qty T W L Material
A 1 3/4” 11” 48” oak
B 2 3/4” 11” 15 5/8” oak
C 1 1/4” 15 1/2” 46” oak plywood
D 2 3/4” 5/8” 16” oak
E 2 3/4” 1 1/2” 15 1/8” oak
F 2 3/4” 1 1/2” 42 3/8” oak G* 1 1/8” 12 5/8” 42 7/8” tempered glass
*Cut glass to fit after door frame is built.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 86/203
H
C
A
B
B
D
J
K
E
F
G
J
I
I
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 87/203
Front View (partial)
C C
H H
I I
A A
J J JK K
B
(behind D)
D D
B
7”TYP
1/4”Rabbet
5/8”TYP
1” DOWEL
9 3/4”
2”TYP
F
E
Side View
Door Front View
(partial)
1/4” wide by 1/8” deep rabbet
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 88/203
1. Cut a 3/4” wide by 3/8” deep dado in both ends of board (A).
Refer to Figure 1 and Isometric.
2. Cut a 3/8” radius on upper front and side edges of board (A).
Refer to Figure 1 and Front and Side Views.
3. Cut a 3/8” wide by 3/8” deep blind dado on upper inside surface of boards (B). (Note that boards (B) are mirror images of each
other.) Refer to Figures 2 and 3 and Isometric.
4. Drill a 3/8” diameter by 3/8” deep hole below the blind dado on the inside surface of boards (B) for door supports. Glue a 3/8”
by 1” dowel into the hole. Refer to Figures 2 and 3 and Isometric.
5. Insert sides (B) into dados in board (A) and attach using glue and 1 1/4” finish nails. Refer to Front and Side Views and
Isometric.
6. Cut a 1/4” wide by 1/4” deep rabbet on back inside edge of subassembly (A, B). Refer to Side View and Isometric.
Figure 1Board A
Figure 2Board B(left side)
Figure 3Board B Section
(left side)
1/2”
1 1/2”
1 5/16”
7/8”
5/8”
3/4”
3/8”
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
R 3/8”
5/8”
1 5/16”
A
B B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 89/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Figure 4Boards B & D Section
Figure 5Door Detail
Figure 6Board F Section
7. Cut a 3/8” radius on front edges and both ends of boards (D).
Refer to Figure 4 and Side View.
8. Attach boards (D) to boards (B) using glue and 1 1/4” finish nails.
Refer to Figure 4, Front and Side Views and Isometric.
9. Drill dowel pin holes in top and bottom edges of boards (B). Refer to Front and Side Views and Isometric.
10. Glue 1” dowels in top edges of boards (B). Refer to Front and Side Views and Isometric.
11. Assemble door frame (E, F) using glue and 1 1/2” dowels. Refer to Figure 5, Door Front View and Isometric.
12. Cut a 3/8” radius on front edges of door frame (E, F). Refer to Figure 6.
13. Cut a 1/4” wide by 1/8” deep rabbet on back inside edge of door frame (E, F). Refer to Figures 5 and 6 and Door Front View.
14. Install 1” dowels in boards (E) to serve as pivots for door hinges. Refer to Figure 5, Door Front View and Isometric.
B
F
DR 3/8”
1/4” wide by
1/8” deep rabbet
1/4” wide by1/8” deep rabbet
R 3/8”
3/4”
5/8”
9/16”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 90/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
17. Assemble top (H, I) using glue and 1 1/4” finish nails. Refer to Front and Side Views and Isometric.
16. Cut a 3/8” radius on front edges and corners of boards (I). Refer to Figure 8 andSide View.
19. Cut a 3/8” radius on front edges and corners of boards (K). Refer to Figure 9 and
Side View.
15. Cut a 3/8” radius on front edge of board (H). Refer to Figure 7 and Side View.
18. Drill dowel pin holes in bottom edges of boards (I). Refer to Front and Side Views and Isometric.
Figure 7Board H Section
HR 3/8”
Figure 8Board I
IR 3/8”
Figure 9Board K
KR 3/8”
20. Assemble bottom frame (J, K) using glue and 1 1/4” finish nails. Refer to Front and Side Views and Isometric.
21. Drill dowel pin holes in top edges of boards (K). Refer to Front and Side Views and Isometric.
22. Glue 1” dowels in top edges of boards (K). Refer to Front and Side Views and Isometric.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 91/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
23. Sand the project.
24. Apply finish to the project.
25. Install glass in the door frame using glass clips. Refer to figure 6. You may wish to apply a bead of silicon caulk to frame before
installing glass to keep glass from rattling.
26. Insert pivoting dowels in boards (E) into dados in boards (B). You may wish to apply wax to the dowels and dados for smoother
operation.
27. Insert back board (C) into rabbet in rear of case subassembly (A,B) and attach using 1/2” brads. Refer to Front and Side Views
and Isometric.
28. Stack cases in preferred configuration using dowel pins and match holes in boards (I), (B) and (K).
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 92/203
U-BILD
Linen Closet
Plan No. 735Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Qty Size Material4 or 5 3/4” x 6” x 96”* lumber of choice
1 1/8” x 13” x 24” masonite
1 1/4” x 28” x 65” plywood
1 1/2” x 10” x 46” plywood
1 3/4” x 48” x 96” veneer plywood**
1 1 1/2” x 1 3/4” x 68” molding***
1 pair 12” drawer guides
4 pairs hinges
4 door handles
2 knobs
1 box 1” finish nails
1 box 1 1/4” finish nails
1 bottle wood glue
12 3/4” wood screws
52 3/8” x 2” dowel pins
1 quart finish of choice
*Approximately 15 1/2 board feet required
**To match lumber of choice
***See Figure 2 for suggested molding profile
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 13 1/4” 68” veneer plywood
B 2 3/4” 13 1/4” 27” veneer plywood
C 1 3/4” 13”* 27” veneer plywoodD 3 3/4” 12 3/4” 27” veneer plywood
E 3 1/4” 3/4” 27” lumber of choice
F 1 3/4” 2” 19 1/2” lumber of choice
G 3 3/4” 2” 24 1/2” lumber of choice
H 1 3/4” 4” 24 1/2” lumber of choice
I 2 3/4” 2” 68” lumber of choice
J 1 1/4” 27 3/4” 64 1/2” plywood
K 1 cut to fit molding
L 2 cut to fit molding
M 4 3/4” 2” 8 3/16” lumber of choice
N 4 3/4” 2” 31 15/16” lumber of choice
O 2 3/4” 8 11/16”* 28 7/16” lumber of choice
P 4 3/4” 2” 7 3/16” lumber of choice
Q 4 3/4” 2” 19 7/16” lumber of choice
R 2 3/4” 7 11/16”* 15 15/16” lumber of choice
S 2 1/2” 4 5/8” 12 3/4” plywood
T 2 1/2” 4 1/4” 22 1/2” plywood
U 1 1/8” 12 3/4” 23” masonite
V 1 3/4” 4 15/16” 24 7/16” lumber of choice
W 2 3/4” 6 1/2” 13” veneer plywood
X 4 1/2” 3” 6 1/2” plywood
*Edge-gluing required to achieve width
Anyone who’s ever grappled with the problem of home storage will
agree that you can never have too much. But no matter how much clos-
et space you have, there’s one thing you can’t change: a closet stays in
one place.
This country-style pine linen closet features three large shelves on
top, two shelves below and a big drawer in-between. Best of all, you
can put it wherever it works best: in the hallway, in the bathroom or in
a bedroom.The linen closet measures 68 inches tall by 29 inches wide by 14
inches deep.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 93/203
3/4” x 48” x 96”Veneer PlywoodCutting Layout
NOTES
1. Read all instructions and check materi-
als before beginning work.
2. Read manufacturer’s instructions
before operating equipment.
3. Always wear safety glasses.
4. We used pine for this project, but
almost any wood may be substituted.
5. Drill pilot holes for finish nails. W
D
B
B
A
A
D D
W C C
Isometric
B
D
O
R
H
E
D
D
C I
I
W
X
A
B
F
G
G
G
M
N
N
M
P
Q
Q
P
A
L
KL
J
E
E
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 94/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Attach boards (A) to boards (B) using glue and 1 1/4” finish nails. Refer to Isometric.
2. Rout a 1/4” by 3/8” wide rabbet around inside back edge of subassembly (A, B) for board (J). Refer to Isometric.
3. Attach trim pieces (E) to leading edges of boards (D) using glue and 1 1/4” finish nails. Refer to Isometric.
4. Attach shelves (D, E) and (C) to subassembly (A, B) using glue and 1 1/4” finish nails. Refer to Figure 1 and Isometric.
Figure 1Shelf Locations
3 1/2
13 1/2
42 3/4
53 1/2
32
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 95/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
5. Mark locations for dowel pins and drill face- and door-frame parts (F), (G), (H), (I), (M), (N), (P) and (Q). Use two dowels pins
per joint.
6. Assemble face frame (F, G, H, I) using glue and dowel pins. Clamp and check for squareness. Refer to Isometric.
7. Glue and nail face frame (F, G, H, I) to cabinet (A, B, C, D, E). Check for squareness. Refer to Isometric.
8. Attach drawer guide mounting blocks (W) and spacer blocks (X) to inside of cabinet sides (A). Drawer guide mounting blocks
(W) must be flush with opening for drawer. Refer to Isometric.
9. Attach back (J) to unit using 3/4” wood screws. Refer to Isometric.
10. Cut molding (K) and (L) to fit and attach to top of unit using glue and 1 1/4”
finish nails. Refer to Figure 2 and Isometric.
10. Cut raised panels (O) and (R) for cabinet doors. Refer to Figure 3.
Figure 2Molding (K) and (L)
Figure 3Door Section
K, L
O, R
M, N,
P, Q
1/4
15 degrees
1/8
1/8
1/4
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 96/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
11. Cut grooves in door frame components (M), (N), (P) and (Q) for cabinet door panels (O) and (R). Refer to Figure 3.
13. Cut grooves in drawer sides (S) for drawer bottom (U). Refer to
Figure 4.
12. Assemble doors (M, N, O) and (P, Q, R) using glue and dowels. Check for squareness and clamp. Refer to Isometric
and Figure 3.
14. Assemble drawer (S, T, U, V) using glue and 1
1/4” finish nails. Refer to Figure 5. Attach
drawer guide following manufacturer’s instruc-
tions.
Figure 4
Drawer Section
S
U
1/4
1/4
Figure 5Drawer Assembly
VT
T
U
S
S
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 97/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
15. Sand project and apply finish.
16. Install hardware, doors and drawer.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 98/203
U-BILD
Lingerie ChestPlan No. 874Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 3/4” x 8” x 120” lumber of choice A, B, H, I
1 3/4” x 8” x 144” lumber of choice O
1 3/4” x 48” x 96” veneer plywood C, D, E, F, G
1 1/2” x 48” x 96” plywood L, M
1 1/4” x 48” x 96” plywood N
1 3/4” x 3/4” x 72” moulding (see Figure 6) J, K
7 3” on center drawer pulls
4 3/8” x 2” dowel pins
7 pairs 14” drawer slides
4 #10 x 1 1/4” flat head wood screws1 box 1 1/4” finish nails
1 can wood filler
1 bottle wood glue
1 quart finish of choice*
NOTE: Hardwood lumber sizes are provided as a base for your own calculations.
Individual boards vary in appearance and defects, which may affect your cutting
layout. Also, leftover scraps can often be reglued and used for other parts.
*We used a fast-drying polyurethane clear satin finish.
A striking combination of beauty and practicality, this lingerie chest displays a time-
less elegance that will ensure its place as a family heirloom. Its clean lines, sturdy con-
struction and simplicity of design make it a natural for almost any decor.
The chest features seven large drawers designed for lingerie, fine knits and other del-
icate articles of clothing. Its generously sized top makes an ideal display surface for
fresh flowers or photographs.
The lingerie chest measures about 27 inches wide by 17 inches deep by 59 inches tall.
Cutting ScheduleItem Qty T W L Material
I 2 3/4” 1 11/16” 17 3/16”* lumber of choice
J 1 3/4” 3/4” 25 1/8”* moulding
K 2 3/4” 3/4” 16 1/4”* moulding
L 14 1/2” 6” 14 1/2” plywood
M 14 1/2” 5 1/2” 17 5/8” plywood
N 7 1/4” 14 1/2” 18 1/8” plywood
O 7 3/4” 7” 20” lumber of choice
Item Qty T W L Material
A 2 3/4” 2” 19 5/8” lumber of choice
B 4 3/4” 2” 57 1/4” lumber of choice
C 1 3/4” 19 5/8” 53” veneer plywood
D 2 3/4” 14” 53” veneer plywood
E 14 3/4” 2” 14” veneer plywood
F 2 3/4” 14” 21 1/8” veneer plywood
G 2 3/4” 15 1/2” 23 5/8” veneer plywood
H 1 3/4” 1 11/16” 27”* lumber of choice
*Approximate size only, cut all moulding to fit.
NOTES
1. Read manufacturer’s instructions
before operating equipment.
2. Always wear safety glasses.
3. We used maple for this project,
but oak, pine or birch will work
equally well.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 99/203
3/4” x 48” x 96”
Veneer Plywood
Cutting Layout
1/2” x 48” x 96”Plywood Cutting Layout
1/2” x 48” x 96”Plywood Cutting Layout
D
D
C
F E E
EEEEEEEEEEE
E
F
G
G
L
L
L L
L L L L L
L L L L L
M M
M
M
M
M
M
M
MM
M M
M
M
N
N
N N NN
N
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 100/203
I
K
IH
G
C
F
B A
A
B
B
E
D
F
D
B
G
K
J
Isometric(Drawer Front O notshown in this view)
N
M
M
L
L
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 101/203
1. Cut legs on boards (B). Refer to Figure 1 and Isometric.
2. Assemble face frame boards (A) and (B) using glue and 3/8”
dowels. Check for squareness. Refer to Figure 2 and Isometric.
3. Attach rear leg boards (B) to back panel (C) using glue. Refer to Isometric.
Figure 1
Board B
Figure 2Face Frame (A, B)
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
4 1/4”
1 1/4”
B
B
A
5 1/4”
1”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 102/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
44 9/16”
37 1/2”
30 7/16”
23 3/8”
16 5/16”
9 1/4”
2 3/16”
3”
2 1/4”
D
E
E
E
E
E
E
E
A
D
E
F
F
A
B B
A
D
E
B
BC
F
Figure 3Subassembly (D, E)
Figure 4
Cabinet Front View
Figure 5Cabinet Top View
4. Attach drawer slide mounting boards (E) to side
panels (D) using glue and 1 1/4” finish nails.
Refer to Figure 3 and Isometric.
5. Attach side subassemblies (D, E) to face frame (A, B) and back subassembly (B, C)
using glue and 1 1/4” finish nails. Check for squareness. Refer to Figures 4 and 5 and
Isometric.
7. Attach top and bottom boards (F) to cabinet subassembly (A, B, C, D, E) using glue and
1 1/4” finish nails. Refer to Figures 4 and 5 and Isometric.
6. Drill four 3/16” holes in top board (F). Refer to Figure 5.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 103/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
8. Laminate top boards (G) together using glue and 1
1/4” finish nails. Refer to Figure 6 and Isometric.
10. Attach top subassembly (G, H, I, J, K) to top board (F) from the inside using 1 1/4”
wood screws through pre-drilled holes inboard (F). Refer to Figure 5 and Isometric.
12. Assemble drawer boxes (L, M) using glue and 1 1/4” finish nails. Refer to Figures 7 and 8 and Isometric.
11. Cut 1/4” wide by 1/4” deep dados in drawer sides (L). Refer to Figure 7 and Isometric.
13. Insert drawer bottom (N) into dados in drawer sides (L) and attach to boards (M) using 1 1/4” finish nails. Refer to Figure 8 and
Isometric.
14. Attach drawer guides to boards (L) and (E). Refer to manufacturer’s instructions.
9. Cut to fit and attach moulding (H), (I), (J) and (K) to
subassembly (G, G) using glue and 1 1/4” finish
nails. Refer to Figure 6 and Isometric.
20
1/4”
R 5/16”
3/4”
G
GJ, K
H, I
Figure 6Cabinet Top (G, H, I, J, K)
Figure 7
Drawer Section (L, M, N) Front View
Figure 8
Drawer Section (L, M, N) Side View
L L
N N
M M
1/4”
1/4”1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 104/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
14. Cut raised-panel design on side edges of drawer face boards (O). Refer to Figures 9 and 10.
15. Cut raised-panel design on top edge of top drawer face board (O) and on bottom edge of bottom drawer face board (O). Refer
to Figures 9 and 10.
16. Attach drawer faces (O) to drawer box fronts (M) using glue and clamps (drawer faces are centered horizontally on drawer
boxes). Refer to Figures 9 and 10. Note: drawer faces (O) may be attached from the inside of the drawer boxes using screws.
17. Sand cabinet and drawer faces.
18. Apply finish to cabinet and drawer faces.
19. Install drawers.
20. Install drawer pulls. Refer to Figure 10. Note: measurements given in Figure 10 are consistent with 3” drawer pulls.
O
Figure 9Drawer Face Detail
Figure 10Drawer Face Front View
5/8”TYP.
3 3/8”
2 1/4”
2 15/16”
TYP.
3”
1/4”TYP.
1 1/2” TYP.
15
L
O
O
L
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 105/203
U-BILD
Oak Cabinet
Plan No. 755Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
5 or 5 1/2 3/4” x 6” x 96”* oak
1 1/8” x 48” x 37” oak plywood
1 1/2” x 10” x 34” plywood
1 pair 12” drawer guides
2 pairs flush mount “H” hinges
2 drawer handles
2 1” knobs
1 small box 1” finish nails
1 small box 1 1/4” finish nails
1 small bottle wood glue
44 3/8” x 2” dowel pins**
*Approximately 20-22 board feet required.
**Biscuits may be substituted.
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 3” 26 1/2” oak
B 2 3/4” 2 1/4” 26 1/2” oak
C 2 3/4” 3” 8 1/4” oak
D 2 3/4” 4” 8 1/4” oak
E 2 1/8” 8 15/16” 20 3/16” oak plywood
F 2 3/4” 3” 26 1/2” oak G 1 3/4” 3” 22 1/2” oak
H 1 3/4” 2” 22 1/2” oak
I 1 3/4” 4” 22 1/2” oak
J 1 3/4” 13 1/2”* 27” oak
K 1 3/4” 15”* 30” oak
L 2 3/4” 4” 15” oak
M 1 3/4” 4” 30” oak
N 2 3/8” 3/4” 14 5/8” oak
O 1 3/8” 3/4” 29 1/4” oak
P 2 3/4” 5” 13 3/8” oak
Q 4 1 1/2”** 2 1/4” 5” oak
R 1 1/8” 27 3/4” 23 1/4” oak plywood
S 4 3/4” 2” 7 3/16” oak T 4 3/4” 2” 12 7/16” oak
U 2 1/8” 7 7/8” 9 1/8” oak plywood
V 2 1/2” 4 5/8” 12 3/4” plywood
W 2 1/2” 4 1/4” 20 1/2” plywood
X 1 1/8” 12 3/4” 21” oak plywood
Y 1 3/4” 4 15/16” 22 7/16” oak
*Edge-gluing required to achieve width.
**Face-gluing required to achieve thickness.
NOTES1. Read manufacturer’s instructions before operating equip-
ment.
2. Always wear safety glasses.
3. We used oak for this project, but almost any lumber
(such as cherry or pine) will work equally well.
4. When using finish nails on oak, drill pilot holes to avoid
splitting.5. Finish project with builder’s choice of stain.
This versatile oak cabinet makes a great storage and display unit that looks great
any room of the house. In the kitchen, it’s perfect for table linens or dishes, and
makes a great sideboard or bar in the dining room. In the family room, use it as an en
table or TV stand and fill it with videotapes, CDs or games.
A handsome addition wherever it’s used, the project measures 27 inches
tall by 29 inches wide by 15 inches deep.
1/8” Oak PlywoodCutting Layout
X
R
U U
E E
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 106/203
Isometric
W
X
V
K
R
G
H
C
C
AE
J
5”
4”
2” F
F
S
S
T
TU
I
M
B
B
D
L
P
A E
V
Y
W
Q
Q
PN
Q
O
3”
Location of dowel pins typi-
cal for all joints (centered
on thickness and spaced
equidistantly on width).
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 107/203
1. Allowing for two dowels per joint, mark and drill side frame boards (A), (B), (C) and (D), face frame boards (F), (G), (H) and
(I) and door frame boards (S) and (T) for 3/8” dowels. Note that biscuits may be substituted for dowels. Refer to Isometric.
3. Insert plywood side panels (E) into side frames (A, B, C, D) and assemble using glue and 3/8” dowels or biscuits. Check for
squareness. Refer to Isometric.
4. Attach side subassemblies (A, B, C, D, E) to shelf (J) using glue and 1 1/4” finish nails. Refer to Isometric.
5. Assemble face frame (F, G, H, I) and using glue and 3/8” dowels or biscuits. Check for squareness. Refer to Isometric.
6. Attach face frame (F, G, H, I) to cabinet using glue and 1 1/4” finish nails. Check for squareness. Refer to Isometric.
7. Attach top (K) to cabinet using glue and 1 1/4” finish nails. Refer to Isometric.
8. Route a 3/8” wide by 1/8” deep rabbet around the inside back edge of cabinet for back (R). Refer to Isometric.
9. Attach trim boards (L), (M), (N) and (O) to cabinet using glue and 1 1/4” finish nails. Refer to Isometric.
2. Cut a 1/8” wide by 3/8” deep dado in boards (A), (B), (C), (D), (S) and (T).
Refer to Figure 1.
Figure 1Typical Frame and
Panel Assembly
C, S
E, U
Outside
3/16”
3/8”
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 108/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
10. Attach spacer blocks (Q) to inside of cabinet side frame boards (A) and (B) using glue and 1 1/4” finish nails. Refer to Isometric
11. Attach drawer guide mounting boards (P) to spacer blocks (Q) using glue and 1 1/4” finish nails. Note that boards (P) must be
flush with sides of drawer opening. Refer to Isometric.
12. Insert plywood door panels (U) into door frames (S, T) and assemble using glue and 3/8” dowels or biscuits. Check for square-
ness. Refer to Isometric.
14. Insert plywood drawer bottom (X) into drawer sides (V) and assemble drawer (T, V, W, X) using glue and 1” finish nails. Check
for squareness. Refer to Isometric.
15. Install drawer guides on drawer sides (V) and drawer guide mounting boards (P) per manufacturer’s instructions.
17. Sand the completed cabinet.
18. Apply finish of choice.
19. Install doors.
20. Install finish hardware.
21. Install drawer on drawer guides.
13. Cut a 1/8” wide by 1/4” deep dado in drawer sides (V). Refer to Figure
2 and Isometric.
Figure 1
Drawer Assembly
V
X
1/4”
1/4”
16. Attach back (R) to cabinet using glue and 1” finish nails. Refer to Isometric.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 109/203
U-BILD
One-Door Ice BoxPlan No. 723
Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
5 3/4” x 6” x 8’* oak
1 1/8” x 48” x 48” oak plywood
32 3/8” x 2” dowel pins
1 box 1 1/4” finish nails
1 bottle wood glue
1 small can finish of choice
1 pair 1 5/16” x 3 3/8” 3/8” offset brass ice box hinges
1 2 1/4” x 2 1/16” brass ice box latch (right-hand)
1 brass ice box name plate
*About 20 board-feet of 3/4” oak
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 3” 23 1/4” oak
B 2 3/4” 2 1/4” 23 1/4” oak
C 2 3/4” 3” 10” oak
D 2 3/4” 4” 10” oak
E 2 3/4” 10” 16 1/4” oak
F 2 1/8” 10 1/2” 16 3/4” oak plywood
G 2 3/4” 3” 23 1/4” oak
H 1 3/4” 3” 16” oak
I 1 3/4” 4” 16” oak
J 1 3/4” 15 1/8” 20 1/2” oak*
K 1 3/4” 2” 20 1/2” oak
L 1 3/4” 2” 22” oak
M 2 3/4” 4” 16 3/4” oak
N 1 3/4” 4” 23 1/2” oak O 1 1/8” 21 1/4” 25 1/4” oak plywood
P 1 3/4” 16 3/4” 20 1/2” oak*
Q 2 3/4” 1 1/2” 16 3/4” oak
R 2 3/8” 3/4” 16 3/8” oak
S 1 3/8” 3/4” 22 3/4” oak
T 2 3/4” 2” 16 7/8” oak
U 2 3/4” 2” 12 5/8” oak
V 1 3/4” 12 5/8” 12 7/8” oak
W 1 1/8” 13 1/8” 13 3/8” oak plywood
*Smaller pieces of stock must be glued-up to create parts (J)and (P). 3/4” oak plywood may be substituted for (J).
NOTES
1. Read all instructions and check materials before
beginning work.
2. Read manufacturer’s instructions before operating
equipment.
3. Always wear safety glasses.
4. Oak is preferred for this project for its authenticity
and beauty.
5. Drill pilot holes in oak before nailing.
There was a time when an ice box like this one could be found in almost every home. Although refrigerators have rendered them obso-
lete, antique oak ice boxes remain popular with collectors, even though they’re usually expensive and hard to find.
This do-it-yourself project and authentic reproduction is neither: it is both inexpensive and easy to build, making use of readily avail-
able materials and requiring only straight cuts. It’s also versatile, and makes a great end table or bedside table.
The one-door ice box measures 26 inches tall by 23 inches wide by 17 inches deep.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 110/203
Isometric
P
A
A
C
C
B
B
H
S
G
G I
N
T U
V
W
U
T
Q
QK
A
B
F
J
D
E
L
M
CO
R
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 111/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Mark location for dowel pins and drill pieces A, B, C, D, G, H, I, T and U. Refer to Figure 1.
2. Assemble and clamp face frame, side frame, and door frames using glue and 3/8" dowel pins as illustrated in Figure 1. Check
frames for squareness.
3. Route a continuous rabbet around the back side openings of the side panel and door frames and install 1/8" plywood panels F and
W. Refer to Figure 1.
4. Using a panel-raising bit, route around all four edges of parts E and V to create raised center panels. Glue center panels E and V
to plywood inserts F and W. Refer to Figure 1.
Figure 1Side Panel, Face Frame and Door Construction
(Back side of door and side panels)
C,H,U
C,H,U
E,V
F,W
A,G,T
A,G,T
D, I, U
D, I, U
A,G,T
A,G,T
Drill and install two 3/8” x 2”dowel pins at this location oneach joint.
Continuous 1/4” x 1/8”rabbet for 1/8” plywood.
5. Nail and glue completed side panels to J, K, L and front face frame. Refer to Isometric and Sections A-A and B-B in Figure 2.
6. Attach top (P), base (M, N) and trim (R, S) with glue and finish nails. Refer to Sections A-A and B-B in Figure 2. Route back of
unit for insertion of 1/8" plywood (O) (see Section C-C in Figure 2).
7. Route a 3/8” shoulder around the inside edges of the door to create a 3/8” offset. Refer to Section B-B in Figure 2.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 112/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
8. Before final assembly, sand and apply finish of choice.
9. Mount door using 3/8” offset hinges. Once door is mounted, determine location and mount door latch.
CR
F
F
E
J J
L
N
D I
M
2”
Section A-A Section B-B Section C-C
Q P
K
P
3/8” or 1/2” radius (TYP.)
3/8” offset door (cut to fit 3/8”offset hardware).
W
O
O W
SH
U
U
V
E
A
B
GT V
Figure 2Sectional Views
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 113/203
U-BILD
Patio Wall & Planter
Plan No. 779Copyright U-Build, Inc., 2001.
All rights reserved. Printed in the U.S.A.
Bill of MaterialQuantity Size Material
1 4” x 4” x 8’ redwood, cedar or fir
10 2” x 4” x 8’ redwood, cedar or fir
6 1” x 6” x 8’ redwood, cedar or fir
24 1” x 4” x 6’ redwood, cedar or fir
4 8” x 8” concrete footings
1 small box 1 1/4” finish nails
1 small box 3” finish nails
1 small box 8d galvanized nails
1 bottle wood glue
NOTES1. Read all instructions and check materials before
beginning work.
2. Read manufacturer’s instructions before operating
equipment.
3. Always wear safety glasses.
4. Redwood is preferred for this project due to its
durability and beauty. Douglas fir and pine also
make an attractive unit. The prototype pictured
was made of Douglas fir and pine.
5. Use wood glue along with finish nails to insure
strong joints.
6. Dimensional lumber was used for this project (e.g.,
the call out is for a 2" x 4", but the actual size is 1
1/2" x 3 1/2"). When selecting the 1" x 6" boardswith tongue and groove with v-joint, finished use-
able surface sizes vary between 5" and 5 1/4". The
cutting schedule will assume your boards are 5"
wide, finish size.
7. To insure that project assembles properly and is
built squarely, use a level and framing square dur-
ing each assembly step.
Cutting SchedulePart Qty T W L Material
A 1 4” 4” 87” redwood, cedar or fir
B 2 2” 4” 44 3/4” redwood, cedar or fir
C 12 1” 6” 44 3/4” redwood, cedar or firr
D 1 2” 4” 87” redwood, cedar or fir
E 4 2” 4” 44 3/4” redwood, cedar or fir
F 22 1” 4” 57 3/4” redwood, cedar or firG 2 2” 4” 87” redwood, cedar or fir
H 1 2” 4” 95” redwood, cedar or fir
I 1 2” 4” 49 1/4” redwood, cedar or fir
J 1 2” 4” 36” redwood, cedar or fir
K 2 2” 4” 23”* redwood, cedar or fir
L 2 2” 4” 15” redwood, cedar or fir
M 1 2” 4” 40” redwood, cedar or fir
N 2 2” 4” 18 1/2” redwood, cedar or fir
O 20 1” 4” 11 1/4” redwood, cedar or fir
P 7 1” 4” 16 1/2” redwood, cedar or fir
*Approximate; check desired mounting height based on distance to the ground
Just the thing to frame a corner of the yard or patio, this patio wall and
planter combination is great for hanging plants and flowers while shel-
tering the barbecue and outdoor dining area from the wind. Out in the
yard, it can screen off a corner where garden tools or garbage cans are
stored. The planter box is built separately, so the builder can decide
whether or not to include it.
The completed wall and planter unit measures about eight feet tall by
eight feet long.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 114/203
Construction Diagram(P not shown)
G
B
AI
E
GF
E
H
E
E
N
N
M
O
L
L
K
K
J
O
O
F
D
C
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 115/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Space concrete footings as shown in Figure 1. Footings should be set in holes and filled with concrete
for stability. Top of footing should be 2" to 3" above the natural grade. Check for level and squareness.
2. Cut 1/4" deep by 1 1/2" wide dados in boards (A), (D) and (G). Cut a 1/4"
deep by 3/4" wide dado in boards (A), (B) and (D). See Construction Diagram
and Figures 2, 3 and 4.
Figure 1Concrete Footing Layout
Figure 2 Figure 3
45 3/4” 46 3/4”
46 3/4”
67 3/4”1 3/8”
1 3/8”
9”
G D A
B
D A
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 116/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
3. Cut a 1/4" by 1/4" notch in the end of Boards (B) where they attach to board (A). See Figure 4.
Figure 4
Figure 5 Figure 6
4. Glue and finish nail boards (B) and (C) to (A). See Figures 4, 5 and 6 and the Construction Diagram. Note that you may have
to cut the bottom board (C) narrower to fit the length of the groove in boards (A) and (D).
5. Glue and finish nail (D) to (B and C). See Figures 5 and 6 and the Construction Diagram.
B
E
C
B
B
D C A
A
1/4”
1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 117/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
10. Cut 45-degree miter on (H) and (I). Glue and nail to top of panels. See Construction Diagram.
9. To complete second panel, glue and finish nail assembly (E, F, G) to first panel (A, B, C, D). Repeat this step for third panel
Refer to Construction Diagram.
8. Glue and finish nail boards (F) to boards (E). See Figure 7.
7. Cut 1/4" deep by 3/4" wide dados in boards (E) for slats (F). See Figure 7.
6. Nail first panel—created by boards (A), (B), (C) and (D)—to built-in straps on concrete piers. Use a brace to help support pane
during construction.
Figure 7
G
G
F
F
E
E
F
F
3”TYP.
3 1/4”
(EACH END)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 118/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Four
12. Glue and nail board (J) to boards (K). Glue and nail boards (L) to subassembly (J, K). Refer to Figure 8
and Construction Diagram.
12. Cut 3/4" wide by 1/4" deep dados in boards (M) and (N). See Figures 9 and 10.
Figure 8
11. Cut notches in boards (J) and (L). See Figure 8.
K
JL
11" 2 "
1 1 /
2 "
1 1 / 2
"
3 1 / 2 " 1 1 / 2 "
Figure 9
M, N
1 1/2"
Figure 10
K M
3/4" x 1/4" dado
1 1/2"
13. Use wood screws or nails and glue to attach (M) to (K). See Figure 10 for proper mounting location.
1 1/2"
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 119/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Five
16. Glue and nail (N) to (K) and (O). Check for squareness.
17. Place planter unit in desired location. Notches in boards (L) rest on board (B). Refer to Construction Diagram. Check height
of boards (K). Nail into place. (You may wish to place boards (K) on concrete or redwood, or seal against water and insects.)
18. Place boards (P) on ledge formed by boards (B, J, L) in bottom of planter to support plants. Refer to Construction Diagram.
15. Glue and nail (O) boards to boards (L). Cut last board on each side to fit and notch same as board (L). Refer to Construction
Diagram.
14. Place boards (O) in grooves in board (M). Refer to Figure 11. Space equally, glue and nail.
Figure 11
M
O
1 1/2"
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 120/203
U-BILD
Pie SafePlan No. 886Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
26 board feet 3/4” pine A, B, C, D, E,
F, G, H, I, J
12 3/8” x 2” dowels
3 10” x 14” tin sheets
1 1 1/2” wood knob
3 1 1/2” x
1 1/2”
butt hinges1 door catch
1 box 1 1/2” finish nails
1 bottle wood glue
1 can wood filler
1 quart finish of choice
You don’t have to be an antiques collector or even a baker
to appreciate this do-it-yourself version of a classic pie
safe. It features three shelves behind a single door, and its
convenient size and simple styling make it a good match
for almost any decor.
The pie safe measures about 40 inches tall by 21 inches
wide by 13 inches deep.
Cutting Schedule
Item Qty T W L Material
A 2 3/4” 11 3/4”* 39 7/8” pine
B 1 3/4” 18 1/8”* 39 7/8” pine
C 3 3/4” 11”* 18 1/8” pine
D 2 3/4” 1 1/4” 39 7/8” pine
E 1 3/4” 2” 17 1/8” pine
F 1 3/4” 2 3/4” 17 1/8” pine
G 1 3/4” 13”* 20 5/8” pine
H 2 3/4” 2” 35” pine
I 2 3/4” 2” 13” pine
J 2 3/4” 2” 13” pine
*Boards A, B, C and G may require edge-gluing to
achieve width.
NOTES1. Read manufacturer’s instructions before operating equipment
2. Always wear safety glasses.
3. Biscuits may be substituted for dowels.
A
B
G
C
E
D
F
H
J
TIN
I
Isometric
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 121/203
Figure 1Side Elevation
Figure 3Board H, I, J Detail
Figure 4Door Construction Detail
Figure 2Door Construction
G
C
A
H, I J
I
H
B
E
D
F 2 3/4”
H
J
I
14 1/2”
26 1/4”
11”
22”
3/4”
1/2” 1/8”
5/16”
2”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 122/203
Assemble Pattern 1 as pictured.
Pattern 1
Board A
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 123/203
Center Line
Pattern 2
Board F
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 124/203
Pattern 3
Tin Design (50%)
Pattern 4
Optional Tulip Design (50%)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 125/203
1. Cut a 1/8” by 1/2” groove in door frame boards (H), (I) and (J). Refer to Figures 2 and 3.
2. Drill face frame boards (D), (E) and (F) and door frame boards (H), (I) and (J) for 3/8” by 2” dowels. Refer to Isometric, Figure
4 and Pattern 2.
3. Assemble face frame (D, E, F) using glue and 3/8” by 2” dowels. Refer to Isometric.
4. Cut a radius in one end of boards (A) and (F). Refer to Isometric, Figure 1 and Patterns 1 and 2.
5. Attach shelves (C) to back (B) using glue and 1 1/2” finish nails. Refer to Isometric and Figure 1.
6. Attach sides (A) to boards (B) and (C) using glue and 1 1/2” finish nails. Refer to Isometric.
7. Attach face frame (D, E, F) to boards (A) and (C) using glue and 1 1/2” finish nails. Refer to Isometric.
8. Attach top (G) to boards (A), (B) and (E) and using glue and 1 1/2” finish nails. Refer to Isometric and Figure 1.
9. Using Pattern 3 as a template, punch the design in the tin door panels. You may wish to substitute Pattern 4 for the heart design
in Pattern 3.
10. Apply your finish of choice to the project.
11. Slide tin into grooves in door frame boards (H), (I) and (J). With the tin panels in place, assemble door frame (H, I, J) using
glue and 3/8” by 2” dowels. Refer to Isometric and Figure 2.
12. Attach door (H, I, J, tin) to the cabinet using three 1 1/2” butt hinges. Install the hinges on the left stile board (H) as follows
the first hinge 1 1/2” from the top, the second in the center and the third 1 1/2” from the bottom.
13. Install the door knob 6 1/2” from the top of the right stile board (H).
14. Install the magnetic catch to the bottom of upper shelf (C) and the inside of right stile board (H).
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 126/203
U-BILD
Plant TablePlan No. 791Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
2 1 1/2” x 2 1/2” x 72” lumber of choice A6 3/4” x 1 1/2” x 96” lumber of choice D, G, I
6 3/4” x 3 1/2” x 96” lumber of choice B, C, E, F
1 3/4” x 7 1/4” x 72” lumber of choice H
1 box 1 1/4” finish nails
1 bottle wood glue
This do-it-yourself plant table is the perfect place to pre-pare plants for the garden. It’s also a great spot for repot-ting or for isolating diseased plants.
The project is about 34 inches tall—standard counterheight—by 46 inches long by 15 inches wide. It supportstwo removable trays, each measuring 7 inches tall by 21inches long by 17 inches wide. The trays, with cut-outhandholds, allow gardeners to carry flowers and plants to
the garden for planting or to move them for proper expo-sure to the sun. Both trays and the bottom shelf of thetable are slatted for drainage.
Cutting Schedule
Item Qty T W L MaterialA 4 1 1/2” 2 1/2” 34” lumber of choice
B 4 3/4” 3 1/2” 45 1/2” lumber of choice
C 4 3/4” 3 1/2” 13 1/4” lumber of choice
D 2 3/4” 1 1/2” 41” lumber of choice
E 11 3/4” 3 1/2” 13 1/4” lumber of choice
F 4 3/4” 3 1/2” 20 1/2” lumber of choice
G 4 3/4” 1 1/2” 19” lumber of choice
H 4 3/4” 7 1/4” 15” lumber of choice
I 22 3/4” 1 1/2” 15” lumber of choice
NOTES1. Read manufacturer’s instructions before
operating equipment.
2. Always wear safety glasses.
3. We used redwood for this project, but cedar
or treated lumber (painted) will work
equally well.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 127/203
Pictorial
B
E
F H
GI
D
A
C
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 128/203
I
I
1/4”
1/4”
I
G
G G
B B
B
B
A AC C
CC
E E
D D
F
F
F
H
H
H
Side View (Table and Tray) Front View (Table and Tray)
Top View (Tray)
R 2
R 1
5 1/2”
2”
8 1/2”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 129/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly Instructions
1. Cut 3/4” x 3 1/2” notches in leg boards (A). Insert boards (B) into notches in boards (A) and attach using glue and 1 1/4” nails
Refer to Side and Front Views and Pictorial.
2. Attach boards (C) to leg subassemblies (A, B) using glue and 1 1/4” nails. Refer to Side and Front Views and Pictorial.
3. Attach shelf support boards (D) 3/4” below the top edge of the lower boards (B) using glue and 1 1/4” nails. Refer to Side and
Front Views and Pictorial.
4. Attach shelf boards (E) to shelf support boards (D) using glue and 1 1/4” nails. (Note: Boards (E) are spaced 1/4” apart.) Refer
to Side and Front Views and Pictorial.
5. Attach tray slat supports (G) to tray sides (F) using glue and 1 1/4” nails. Refer to Side, Front, and Top Views and Pictorial.
6. Cut a 2” radius on tray ends (H). Refer to Side View.
7. Drill two 1” holes in tray ends (H) and connect the holes (using a keyhole saw or jigsaw) to form tray handles. Form a 1/4”
radius on the handles and upper edges of boards (H) using a router, sander or rasp. Refer to Side, Front and Top Views.
8. Attach tray sides (F) to tray ends (H) using glue and 1 1/4” nails. Refer to Side, Front and Top Views and Pictorial.
9. Attach tray slats (I) to slat supports (G) using glue and 1 1/4” nails. (Note: Boards (I) are spaced 1/4” apart.) Refer to Side
Front and Top Views and Pictorial.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 130/203
Planter BenchPlan No. 878Copyright U-Build, Inc., 1998.
All rights reserved. Printed in the U.S.A.
Bill of MaterialMaterials for 3 planter boxes and 2 benches
Quantity Size Material Item
1 3/4” x 4’ x 8’ Exterior Plywood A
2 1 1/2” x 1 1/2” x 8’ Redwood B
15 5/8” x 3 5/8” x 12’ Redwood S4S* C, D, E,
F, G, H, I
1 Small Box 1” Finish Nails
1 Small Box 2” Finish Nails
1 Small Bottle Wood Glue
1 Quart Finish
*S4S (surface four sides) material is milled smooth and is usually
5/8” thick.
Cutting ScheduleMaterial for 1 box*
Part Qty T W L Material
A 2 3/4” 16 7/8” 16 7/8” Plywood
B 8 1 1/2” 1 1/2” 15 3/8” Redwood 2x2
C 20 5/8” 3 3/8” 16” Redwood 1 x4 S4S**
D 4 5/8” 1 3/4” 19 3/8” Redwood 1 x4 S4S**
E 4 5/8” 1 1/4” 19 3/8” Redwood 1 x4 S4S**
F 4 5/8” 1 3/4” 20 3/8” Redwood 1 x4 S4S**
Material for 1 bench*
G 4 5/8” 3 3/8” 36” Redwood 1 x4 S4S**
H 5 5/8” 1 1/4” 13 7/8” Redwood 1 x4 S4S**
I 2 5/8” 2 1/2” 36” Redwood 1 x4 S4S**
*The planter bench as pictured has 3 boxes and 2 benches.
**S4S (surface four sides) material is milled smooth and is usually
5/8” thick.
This simple and elegant planter bench project is ideal for the porch, patio or pool. Filled with plants and flowers, it will define a cor-
ner of the porch or patio with style.
Featuring all straight cuts and modular construction, the project allows the builder to decide what combination of planter boxes and
connecting benches works best for their own space. Bills of material are included for individual boxes and benches, as well as for the
combination pictured.
The planter bench as pictured is built from redwood for its beauty, strength and durability, although other woods can be substituted
if properly treated. The finished planter boxes measure about 20.5 inches square by 17 inches tall, and the benches measure 36 inch-
es long by 15 inches wide.
ISOMETRIC OF
PLANTER BOX
ISOMETRIC OFPLANTER BENCH
A
A
B
H
I
G
C
D
E
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 131/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
1. Glue and nail with 2" finish nails boards B to plywood A.
Make two units with a hole cut in the top unit for a planter
pot (see illustration 1).
2. Glue and nail with 1" finish nails boards C to plywood
frames. Lay boards out before nailing to achieve equal
spacing (see illustration 2). Check for squareness.
3. Glue and finish nail with 1" finish nails boards D, E and F
as shown in illustration 1 and 2.
4. Glue and finish nail with 1" finish nails boards H
to seat slats G. Space seat slats as shown in illus-
tration 1. Lay boards out before nailing to
achieve equal spacing (see illustration 3). Check
for squareness.
5. Attach boards I to front and back of bench with
1" finish nails and glue. Use sufficient glue and
nails, as these are the boards that give the bench
strength. Sand and apply finish.
Illustration 1
Illustration 2
Illustration 3
Illustration 4
Assembly Instructions
6. Sand and apply finish to assembled planter boxes and benches.
Assemble boxes and benches as shown in illustration 4.
Diameter
of Pot
16 7/8
13 7/
F
A
C
A
B
A
C
E
B D
F
3
2
H
H
I
I
I
G
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 132/203
Potting BenchPlan No. 910Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
4 1 1/2” x 3 1/2” x 10’ redwood, cedar or fir
7 5/8” x 5 3/8” x 10’ redwood, cedar or fir
54 #7 x 1 5/8” wood screws
8 #8 x 2 1/2” wood screws
28 #8 x 3” wood screws
1 small box 1 1/4” finish nails
1 small can wood filler
1 small bottle wood glue
1 quart finish of choice
Cutting Schedule
Item Qty T W L Material
A 2 1 1/2” 3 1/2” 36” redwood, cedar or fir
B 2 1 1/2” 3 1/2” 65” redwood, cedar or fir
C 4 1 1/2” 3 1/2” 21” redwood, cedar or fir
D 2 1 1/2” 3 1/2” 21” redwood, cedar or fir
E 1 1 1/2” 3 1/2” 45” redwood, cedar or fir
F 1 1 1/2” 3 1/2” 48” redwood, cedar or fir
G 1 1 1/2” 3 1/2” 18” redwood, cedar or fir
H 3 5/8” 5 3/8” 45” redwood, cedar or fir
I 2 5/8” 5 3/8” 27 7/8” redwood, cedar or fir
J 2 5/8”
1”
11 11/16”
redwood, cedar or firK 2 5/8” 5 3/8” 23 1/4” redwood, cedar or fir
L 4 5/8” 5 3/8” 50 1/2” redwood, cedar or fir
M 1 5/8” 5 3/8” 50 1/2” redwood, cedar or fir
N 3 5/8” 5 3/8” 45” redwood, cedar or fir
O 2 5/8” 1” 16 1/8” redwood, cedar or fir
P 2 5/8” 5 3/8” 45” redwood, cedar or fir
Q 2 5/8” 5 3/8” 17 3/8” redwood, cedar or fir
R 1 5/8” 4 3/4” 16 1/8” redwood, cedar or fir
S 1 5/8” 4 3/4” 29” redwood, cedar or fir
NOTES1. Read all instructions and check materials
before beginning work.
2. Read manufacturer’s instructions before
operating equipment.
3. Always wear safety glasses.
4. Although redwood is preferred for this pro-
ject, cedar or fir may be substituted.
This do-it-yourself potting bench makes it easy to get a head
start on warm-weather gardening. It features a generously-
sized work top with a hutch above for tools, seeds and small
pots. Below, shelves hold larger items, and a large compart-
ment is just right for bulky bags of potting soil, fertilizer or acovered compost container. Best of all, the design is simple
enough to build in a weekend or two, even if you're more gar-
dener than woodworker.
The potting bench measures about 51 inches long by 24
inches deep by 65 inches tall.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 133/203
Construction Diagram 1(E, G and O not shown)
Q
N
N
N
P
M
D
K
K
C
C
A
H
H
H
I
I
J
J
B
B
C
A
F
L
L
L
L
P
S
R
Q
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 134/203
B
L
M
L
L
L
F
P
P
B
M
L
F
K
J
I
JH
C C
C C
A A
GD D
B
F D
C
A
C
I IB
J
L
M
E
B
P
OQ
P
S
O O N
N
RN
G
B
D
1/8” SPACE BETWEEN BOARDS (L)C
A
I
ID
C
A
Construction Diagram 2
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 135/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Drill holes in boards (C), (E), (F), (H) and (K). Refer to Figures 1 through 4.
Figure 1Boards C
Figure 3Board F
Figure 4Boards H and K
Figure 2Board E
3/4”
3/4”
2 3/4”
4 1/4”
2 1/4”
3/4”
3/4”1”
1”1”
Center Line
Center Line
3/4”
1”
NOTE: Drill holesonly in one end of
boards (K).
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 136/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
2. Drill holes in boards (L), (M) and (N). Refer to Figures 5 through 7.
Figure 5Boards L
1”
HOLE LOCATIONFOR FRONT BOARD (L)
2”
Center Line
Figure 6Board M
Figure 8Boards A and B
Figure 7Boards N
1 3/8”
1 1/2”
21 1/2”
3 1/2”
4”
4 1/2”1 3/4”
2”(top board)
2 11/16”(middle board)2”
(bottom board)
1”
3. Notch boards (A) and (B) for boards (C). See Figure 8.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 137/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
4. Drill holes in boards (I). Notch one of the (I) boards for board (E). Refer to Figure 9.
5. Attach boards (C) to boards (A) and (B) with 3" wood screws and glue.
6. Attach board (D) to (A) and (B) using 3" screws and glue.
7. Attach boards (E) and (F) to back and front of project using 2 1/2" wood screws and glue.
8. Use 3" wood screws and glue to attach (G) to (E) and (F).
9. Use 1 5/8" wood screws and glue to attach (I) to (G) and (K) to (C). Attach boards (J) to (I) and (H) using 1 1/4" finish nailsand glue.
10. Attach bench top boards (L) and backboard (M) with 1 5/8" wood screws. Do not glue so that the bench top boards may be
replaced.
11. Attach support boards (O) to the back of boards (N) using 1 1/4" finish nails and glue.
12. Assemble (P), (Q), (R) and (S) to (N) using glue and 1 1/4" finish nails.
13. Attach upper shelf assembly to boards (B) using 1 5/8" wood screws.
NOTE: For steps 5 through 13, refer to Construction Diagrams 1 and 2. Check assembly for squareness after completing each step.
Figure 9Boards I
1 1/2”
1”
1” 1”
1”
3 1/2”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 138/203
U-BILD
PVC Dining SetPlan No. 665Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of MaterialChair*
Quantity Size Material
20 feet 1 1/2” Schedule 40 PVC Pipe
8 1 1/2” 90 degree PVC elbows
6 1 1/2” PVC tees
18” x 72” heavy canvas**
1 spool heavy-duty thread
1 can PVC cement
Table
Quantity Size Material
16 feet 1 1/2” Schedule 40 PVC Pipe8 1 1/2” 45 degree PVC elbows
4 1 1/2” PVC tees
4 1 1/2” PVC caps
1 1/2” x 48” x 72” particle board
1 1/2” x 48” x 60” plastic laminate
1 pint contact cement
1 small bottle white glue
1 small box 3/4” finish nails
1 small can PVC cement
*Quantity listed is per chair
**For 4 chairs purchase 4 yards (36” x 144”) of heavy canvas
Do-it-yourselfers can create this attractive, weatherproof, light-
weight and durable outdoor dining set in a couple of weekends
and at a fraction of the cost of ready-made patio sets. The key is
PVC pipe.
Construction is simple. Just cut the pipe to length, assemble
with PVC cement and add the table top and chair seats.
The tabletop measures 48 inches square.
NOTES1. Read all instructions and disclaimer (see last page) and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. Always wear safety glasses.
4. Use only Schedule 40 PVC pipe.
5. When using PVC cement, carefully follow directions.
6. The chair will safely hold up to 250 pounds.
7. If you wish to paint your PVC project, use plastic paint (check with your local home center). If you are painting the
project, lightly sand the PVC pipe first.
Cutting ScheduleChair*
Part Qty Size Material
A 3 20 1/4” 1 1/2” PVC pipe
B 2 6” 1 1/2” PVC pipe
C 2 10” 1 1/2” PVC pipe
D 2 8 1/2” 1 1/2” PVC pipe
E 2 6” 1 1/2” PVC pipe
F 2 12 1/2” 1 1/2” PVC pipe
G 4 22” 1 1/2” PVC pipe
H 1 18” x 54” heavy canvas
I 1 18” x 18” heavy canvasTable
Part Qty Size Material
A 4 10 1/2” 1 1/2” PVC pipe
B 8 4 1/4” 1 1/2” PVC pipe
C 4 24 1/4” 1 1/2” PVC pipe
D 1 1/2” x 48” x 48” particle board
E 2 1/2” x 3” x 48” particle board
F 2 1/2” x 3” x 42” particle board
G 8 1/2” x 2” x 6 3/8” particle board
H 8 1/2” x 2” x 2 3/8” particle board
I 4 1/16” x 2” x 48 3/4” plastic laminate
J 1 1/16” x 48 3/4” x 48 3/4” plastic laminate
*Quantity listed is per chair
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 139/203
Figure 1Chair Pictorial
H
G
G
A
B
C
E
F
D
A
A
I
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 140/203
Figure 2Table (top view)
Figure 3
Table (side view)
A
B
B
B
B
A
A
(Plastic laminate)
Particle board top
Edge of table top
A
C
I
B B
Rails
Leg supports1 1/2” PVC cap
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 141/203
Assembly InstructionsPage One
Read all instructions before beginning any work.
1. Cut PVC pipe to length (refer to Cutting Schedule) and sand ends of pipe to remove rough edges.
2. Using elbows, tees and glue, assemble chair sides (B, C, D, E, F, G). Refer to Figure 1. Make sure the two sides are identical.
Figure 6Canvas Assembly (Parts H & I)
4. Measure and cut canvas to size (see Figures 4 and 5).
5. Sew a 3/8” hem on each lengthwise edge of pieces H and I (see Figures 4
and 5).
6. Fold each end of piece H under and sew as illustrated in
Figures 4 and 6.
7. Fold piece I in half and sew to piece H (see Figures 5 and 6)
18
18 1/2
54
39
20 1/2
F O L D
C A N V A S
H E R E
A T T A C H
( I ) H E R E
F O L D
C A N V A S
H E R E
T O P
O F C H A
I R
H
7 1/2 7 1/2
3/8HEM
F O L D
C A N V A S
H E R E
I
18
9
I
H
SEW AT THESE POINTS
Figure 4Canvas Layout (Part H)
Figure 5Canvas Layout (Part I)
18
3/8HEM
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 142/203
Read all instructions before beginning any work.
Assembly InstructionsPage Two
8. Install seat canvas assembly (H, I) on cross pieces (A). Refer to Figures 1 and 7.
10. Using elbows, tees and glue, assemble table base unit (A, B, C). Take particular care that legs (C) are vertical and the same length
Refer to Figures 2 and 3.
11. Cut table top (D), rails (E) and (F) and leg supports (G) and (H) to size. Refer to Cutting Schedule.
12. Attach rails (E) and (F) to underside of
table top using white glue and 3/4” finish
nails. Refer to Figures 3 and 8.
Figure 7Seat Canvas Installation
Figure 8
Position for Table Parts(E), (F), (G) and (H)
I
H
INSERT CROSS PIECES (A)
AT THESE POINTS
9. Using elbows, tees and glue, assemble chair unit sides (B, C, D, E, F, G) to cross pieces (A) and seat canvas (H, I). Refer to Figure 1
E
G
F
H
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 143/203
Read all instructions before beginning any work.
Assembly InstructionsPage Three
13. Using table base (A, B, C) as a guide attach leg supports (G) and (H) to underside of table top using white glue and 3/4” finish
nails. Refer to Figures 3 and 8.
14. Attach plastic laminate edge pieces (I) to table top edges using contact cement. Refer to Figure 3.
15. Attach plastic laminate table top piece (J) to table top (D) using contact cement. Trim flush with edges.
16. Place table top (D, I, J) onto table base (A, B, C).
DisclaimerCertain conditions, including but not limited to ultraviolet rays of the sun, may in time weaken PVC pipe. U-Bild disclaims any and
all liability for any damages sustained by anyone for any cause whatsoever, including but not limited to the construction and/or use of
this PVC project.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 144/203
U-BILD
PVC Lawn SwingPlan No. 678Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
50 feet 2” Schedule 40 PVC Pipe30 feet 1 1/4” Schedule 40 PVC Pipe
26 feet 1” Schedule 40 PVC Pipe
10 2” 90 degree PVC elbows
6 2” x 2” x 2” PVC tees
4 2” x 1” x 2” PVC tees*
8 1 1/4” 90 degree PVC elbows
10 1 1/4” x 1 1/4” x 1 1/4” PVC tees
4 1” 90 degree PVC elbows
8 1” x 1” x 1” PVC tees
1 can PVC cement
2 5/16” x 5” eye bolt w/ nut and washer
4 5/16” x 4” eye bolt w/ nut and washer
18 feet 1 5/8” link straight link chain**
6 chain connectors
44 #8 x 1/2” sheet metal screws w/ washers
4 yards 58” wide heavy canvas
9 yards edging material for cover
1 spool heavy-duty thread
2 18” x 22” cushions
2 22” x 22” cushions
* If 2” x 1” x 2” PVC tees are unavailable, use 2” x 2” x 2” PVC
tees fitted with 2” x 1” reducers
** 520 lb. working load limit
Cutting Schedule
Base Unit
Part Qty Size Material
A 1 50 1/2” 2” PVC pipe
B 8 6” 2” PVC pipe
C 2 48” 2” PVC pipe
D 4 72” 2” PVC pipeE 4 3 1/4” 2” PVC pipe
F 2 39” 2” PVC pipe
G 2 2 1/2” 2” PVC pipe
H 4 54” chain
Chair Unit
Part Qty Size Material
I 4 19 1/2” 1 1/4” PVC pipe
J 4 10” 1 1/4” PVC pipe
K 5 2 1/4” 1 1/4” PVC pipe
L 2 6 1/4” 1 1/4” PVC pipe
M 2 5” 1 1/4” PVC pipe
N 4 22 1/8” 1 1/4” PVC pipe
O 2 46” 1 1/4” PVC pipeP 1 43 1/2” x 52” canvas
Cover Unit
Part Qty Size Material
Q 4 2” 1” PVC pipe
R 2 3 3/4” 1” PVC pipe
S 4 14 1/2” 1” PVC pipe
T 2 40” 1” PVC pipe
U 4 16” 1” PVC pipe
V 2 35 1/2” 1” PVC pipe
W 1 56 1/2”x 96” canvas
X 1 26’ edging material
Believe it or not, anyone can create an inviting retreat like this com-
fortable lawn swing in about a day. The only materials required are
PVC pipe and adhesive, canvas, chain, cushions and assorted hard-
ware.
To build, just cut the pipe to length and assemble into three basic
units, attach the fabric and hang the seat. To finish, cut the cover
material to size and fit it over the cover frame, add seat cushions and
pour the iced tea.
The project measures about 5 feet by 6 feet at the base and stands 6feet high.
Read all instructions before beginning any work.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 145/203
B
G
E
E
E
B
B
E
F
F
B
B
B
B
B
C
CAD
D
D
D
G
Base UnitConstruction Diagram
2” x 1” x 2”reducing tees
NOTES1. Read all instructions and disclaimer (see last page) and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. Always wear safety glasses.
4. Use only Schedule 40 PVC pipe.
5. When using PVC cement, carefully follow directions.
6. The chair will safely hold up to 350 pounds.
7. If you wish to paint your PVC project, use plastic paint (check with your local home center). If you are painting the
project, lightly sand the PVC pipe first.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 146/203
Cover UnitConstruction Diagram
Chair UnitConstruction Diagram
U
U
V
T
X
W
T
S
Q
Q
R
S
S
U
V
U
Q
Q
R
S
OSheet metal screws
and washers every 3”
(fabric attachment)
M
J I
JO
L
IN
N
P
J
I
M
J
L
I
N
K
K
K
N
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 147/203
Assembly InstructionsPage One
Read all instructions before beginning any work.
1. Cut PVC pipe to length (refer to Cutting Schedule).
2. Sand ends of pipe to remove rough edges.
3. Using elbows, tees and glue, assemble sides of chair unit (I, J, K, L, M). Refer to Chair Unit Construction Diagram. Make sure
the two sides are identical.
4. Using elbows, tees and glue, assemble chair unit sides to cross pieces (N) and (O). Refer to Chair Unit Construction Diagram.
5. Drill holes and install eye bolts in chair unit. Refer to Figure 1.
6. Mark cross pieces (N) and (O) every 3” and drill holes for sheet metal screws to attach seat fabric. (Hole size is determinded by
screw size.) Holes are drilled in underside of upper cross piece (O), forward-facing surface of lower cross piece (O) and rear-fac-
ing surface of upper cross pieces (N). Refer to Chair Unit Construction Diagram.
Figure 1Chair Unit Bolt Location
JJ
N/O N/O
N/O N/O
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 148/203
Read all instructions before beginning any work.
Assembly InstructionsPage Two
10. Using elbows and tees, assemble cover unit without glue, making sure that cross members (Q, R, S) are aligned properly to mate
up with mounting points on base unit. Apply glue and reassemble. Refer to Cover Unit Construction Diagram.
8. Using sheet metal screws and washers, install fabric to chair frame as follows: Attach fabric to underside of upper cross piece (O)
wrap around and attach to lower cross piece (O). Working toward front of chair, pull fabric over and around upper cross pieces
(N), and attach from back. Refer to Chair Unit Construction Diagram.
9. Using elbows, tees and glue, assemble base unit. Take particular care that upper assembly (B, E, F, G) is aligned properly. Refer
to Base Unit Construction Diagram.
Figure 2Chair Fabric
P
43 1/2
5
4
52
7. Cut chair fabric to size. Refer to Figure 2.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 149/203
Read all instructions before beginning any work.
Assembly InstructionsPage Three
11. Drill holes and install eye bolts in base unit. Refer to Figure 3. Attach chains to eye bolts using chain connectors.
12. Attach chair unit to base unit using chain connectors.
13. Attach cover unit to base unit. If you want the cover to be removable, do not glue parts (Q) to the base unit.
14. Using cover unit frame as
a guide, cut cover fabric to
size and attach edging.
Use Figure 4 for general
reference only.
Figure 3Base Unit Bolt Location
FF
EE
BB
DD
Figure 4Cover Fabric
W
96
9
56 1/2
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 150/203
Read all instructions before beginning any work.
Assembly InstructionsPage Four
15. Place cover fabric over cover unit frame (it is not necessary to attach the fabric with screws).
16. Place cushions on chair unit and adjust height by adjusting chain length.
DisclaimerCertain conditions, including but not limited to ultraviolet rays of the sun, may in time weaken PVC pipe. U-Bild disclaims any and
all liability for any damages sustained by anyone for any cause whatsoever, including but not limited to the construction and/or use of
this PVC project.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 151/203
PVC
Twin SeaterPlan No. 726Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
50 feet 1 1/2” Schedule 40 PVC Pipe
16 1 1/2” 90 degree PVC elbows
18 1 1/2” PVC tees
1 piece 3/4” x 18” x 36” particle board
1 small can PVC cement2 yards 58” wide heavy canvas
1 spool heavy-duty thread
2 18” x 22” cushions
2 22” x 22” cushions
Cutting Schedule
Part Qty T W L Material
A 6 21 1/2” 1 1/2” PVC pipe
B 4 5 3/4” 1 1/2” PVC pipe
C 2 10 1/4” 1 1/2” PVC pipeD 4 7 1/4” 1 1/2” PVC pipe
E 6 23” 1 1/2” PVC pipe
F 2 7 1/4” 1 1/2” PVC pipe
G 4 10 1/4” 1 1/2” PVC pipe
H 6 2 1/2” 1 1/2” PVC pipe
I 2 5 1/2” 1 1/2” PVC pipe
J 4 10 3/8” 1 1/2” PVC pipe
K 3 20 3/4” 1 1/2” PVC pipe
L 2 19 1/4” 56 1/2” Canvas
M 2 16 1/2” 19 1/4” Canvas
N 1 3/4” 18” 29” Particle Board
O 2 3/4” 1 3/4” 18” Particle Board
NOTES
1. Read all instructions and check materials
before beginning work.
2. Read manufacturer’s instructions before
operating equipment.
3. Always wear safety glasses.
4. Use only Schedule 40 PVC pipe.
5. When using PVC cement, carefully follow
directions.
6. Hardboard may be substituted for particle
board.
7. Each seat will safely hold up to 250
pounds.
8. If you wish to paint your PVC project, use
plastic paint (check with your local home
center).
It’s easy to see that outdoor furniture made from PVC pipe is
attractive, inexpensive, lightweight, durable, weather-resistant
and easy to clean and maintain. For do-it-yourselfers, it’s also
a snap to build.
This PVC twin seater project has two wide seats with a
convenient table in between, and takes only an afternoon or two to build. After sawing the pipe to length, simply fit it
together as shown. To finish, add canvas, seat cushions and a particle board tabletop.
The project measures about 64 inches long by 23 inches deep by 30 inches tall.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 152/203
Assembly InstructionsPage One
Read all instructions before beginning any work.
1. Cut PVC pipe to length (refer to Cutting Schedule).
2. Sand ends of pipe to remove rough edges.
3. Assemble pipe to check all lengths for correct size (see Figure 1). Do not cement at this stage.
A
H
E
B
K
K
K
B
C
D
A ED
J
J
G
I
E G
F A
A
H
G
AE
E
E
G
F
D
J
J
I
B
B
C
D
A
H
H
H
H
Figure 1
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 153/203
Read all instructions before beginning any work.
Assembly InstructionsPage Two
Figure 2
Figure 3Figure 4
4. Measure and cut canvas to size (see Figures 2 and 3).
5. Sew a 3/8” hem on each lengthwise edge of pieces L and M (see Figures 2 and 3).
6. Fold each end of piece L under and sew as illustrated in Figures 2 and 4.
7. Fold piece M in half and sew to piece L (see Figures 3 and 4).
19 1/4
21 1/2
56 1/2
41 1/2
20
F O L D
C A N V A S
H E R E
T O P
O F C H A I R
L
7 1/2 7 1/2
3/8
HEM
F O L D
C A N V A S
H E R E
M
16 1/2
8 1/4
ML
SEW AT THESE POINTS
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 154/203
N
O
Figure 5
Figure 6
Read all instructions before beginning any work.
Assembly InstructionsPage Three
8. Cement the sides of the chairs together (parts B, C, D, E, F, G, H, I and J and fittings). As you cement, line up each half to ensure
that they are the same size.
9. Fit the canvas over parts A and assemble to chair sides without cement. Make sure the canvas fits tightly on the chair frame.
10. Paint the project (optional) at this point (see Notes).
11. Cement parts A and K in place for final assembly of the PVC unit (see Figure 1).
12. Cut and assemble the table top (see figure 5). Radius each
end of parts O with a 1” radius.
13. Rout the edge of the table with a 3/8” radius.
14. Paint table and place on PVC unit (see Figure 6).
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 155/203
Space-Saver
WorkbenchPlan No. 916Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
Bill of Material
Qty Size Material Item
3 3/4” x 48” x 96” plywood A, B, D, F, H,
J, L, M, O, R
1 3/4” x 5” x 72” lumber of choice C, E, G, I, K,
N, P, Q
1 3/4” x 7” x 96” lumber of choice S, T
4 2” x 4” x 96” lumber of choice U, V, W
16 #8 x 2 1/2” wood screws
1 box 3/4” finish nails
1 box 1 1/4” finish nails
1 can wood filler
1 bottle wood glue4 1 1/2” x 36” piano hinges
4 3” butt hinges
2 lid supports
12 3/16” shelf supports
2 latches
1 4” barrel bolt
4 3/8” x 3 1/2” lag bolts
1 quart finish*
*We used a fast-drying polyurethane clear satin finish
Cutting Schedule
Item Qty T W L Material
A 1 3/4” 32” 71 1/4” plywood
B 2 3/4” 9 3/4” 71 1/4” plywood
C 2 1/4” 3/4” 71 1/4” lumber of choice
D 2 3/4” 9 3/4” 33 1/2” plywood
E 2 1/4” 3/4” 33 1/2” lumber of choice
F 1 3/4” 8 3/4” 71 1/4” plywood
G 1 1/4” 3/4” 71 1/4” lumber of choice
H 2 3/4” 8 3/4” 23 1/4” plywood
I 2 1/4” 3/4” 23 1/4” lumber of choice
J 3 3/4” 8 3/4” 23” plywood
K 3 1/4” 3/4” 23” lumber of choice
L 1 3/4” 7 7/8” 71 1/4” plywood
M 2 3/4” 4” 71 1/4” plywood
N 4 1/4” 3/4” 71 1/4” lumber of choice
O 2 3/4” 4” 8 7/8” plywood
P 4 1/4” 3/4” 4” lumber of choice
Q 4 1/4” 3/4” 9 3/8” lumber of choice
R 2 3/4” 22 1/2” 71 1/4” plywood
S 2 3/4” 3” 71 1/4” lumber of choice
T 2 3/4” 3” 24” lumber of choice
U 4 1 1/2” 3 1/2” 34” lumber of choice
V 4 1 1/2” 3 1/2” 21” lumber of choice
W 2 1 1/2” 3 1/2” 74” lumber of choice
If you’re a do-it-yourselfer, here’s a great way to maximize valuable
shop space: a full-size, wall-mounted workbench that folds up into
a neat, 13-inch-deep package. It even has space for a built-in light
and plenty of storage shelves.
The workbench is as easy to use as it is to build. To close, fold
the lightbox down, remove the cross braces from the legs, lift thebenchtop and latch into place. Fold the legs into the bottom of the
benchtop, shoot the bolt and slide the cross braces in behind the legs
The project measures about 72 inches long by 34 inches deep by
74 inches tall. It folds up to about 72 inches long by 13 inches deep
by 34 inches tall.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 156/203
NOTES1. Read all instructions and check materials before beginning work.
2. Read manufacturer’s instructions before operating equipment.
3. Always wear safety glasses.
4. We used maple for this project, but almost any wood may be substituted.
3/4” x 48” x 96”
Plywood Cutting Layouts
A
B
B
M
M
D
L
R
R
D
O O
F
J
J
J
H
H
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 157/203
Pictorial
L
N
N
Q
E
M
A
O
B
B
D
D
F
H
J
C
R
S
TV
V
V
U
U
U
U
W W
E
I
P
T
G
K
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 158/203
A
V
V U
V
W
T a b l e i n d o w n p o s i t i o n
L i g h t b o x f r o m f r o n t i n o p e n p o s i t i o n
D r i l l 6 h o l e s 3 / 8 ” d i a m
e t e r a s s h o w n f o r 3 / 8 ” x 3 1 / 2 ” l a g b o l t s
w a l l s t u d s
D
T
H I
P
M
C
N
E
K
S
G
B
F
3 t y p .
1 3 t y p .
1
/ 8 ” g a p
t y p .
J
F i g u r e 1
F r o n t V i e w
L o c a t i o n o f l a t c h e s
( o n e o n e a c h s i d e )
A
M
L
S G D K
P
E
B
Q
O
B
R
T
S
V V
U
U
F J
6
2 9
F i g u r e 2
S i d e V
i e w
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 159/203
Figure 3Light Box
(bottom view)
L NM
Q
O
Figure 5Board T
41 1/2 R 5/16
Figure 4Table Assembly(folded position)
R
U
V VVV
U U
U
S
S
T
4” barrel bolt
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 160/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Attach edge trim (C), (E), (G), (I), (K), (N), (P), and (Q) to boards (B), (D), (F), (H), (J), (M) and (O) using glue and 3/4” fin-
ish nails. Refer to Pictorial and Figures 1 and 2.
2. Drill 3/16” holes (for shelf supports) on both sides of boards (H) and on the
inside of boards (D). Refer to Figure 6.
3. Attach top and bottom subassemblies (B, C) to board (A) using glue and 1 1/4” finish nails. Refer to Pictorial and Figures 1 and 2
4. Attach sides (D, E) to subassembly (A, B, C) using glue and 1 1/4” finish nails. Check for squareness. Refer to Pictorial and
Figures 1 and 2.
5. Using vertical dividers (H, I) as placement guides, attach shelf (F, G) to cabinet using glue and 1 1/4” finish nails. Check for
squareness. Refer to Pictorial and Figures 1 and 2.
Figure 6Hole Pattern Diagram
(Boards D and H)
1 1/2
1 1/4
6
8
6. Using a square and shelves (J, K) as placement guides, attach vertical dividers (H, I) to cabinet using glue and 1 1/4” finish nails
Refer to Pictorial and Figures 1 and 2.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 161/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
7. Attach light box sides (M, N) to light box top (L) using glue and 1 1/4” finish nails. Refer to Pictorial and Figures 1 through 3
8. Attach ends of light box (O, P, Q) to subassembly (L, M, N) using glue and 1 1/4” finish nails. Check for squareness. Refer to
Pictorial and Figures 1 through 3.
9. Using glue and 1 1/4” finish nails, fasten boards (R) together back-to-back (veneer side out) to create one, 1 1/2”-thick sheet for
the bench top.
10. Cut notches in boards (T). Refer to Figure 5.
11. Attach boards (S) and (T) to the edges of the bench top (R) using glue and 1 1/4” finish nails. Refer to Pictorial and Figures 12 and 4.
12. Sand and apply finish to all parts, including leg boards (U), (V) and (W).
13. Attach light box to cabinet using piano hinge. Refer to Pictorial and Figure 2. Install lid supports. If using lid supports from
U-Bild Space-Saver Workbench Hardware Kit (No. 916HK), refer to Figure 7.
14. Install fluorescent light fixture in light box.
Figure 7
Lid Support Installation Guide
3 3/81 1/2
2 3/4
1 5/8
1 1/4
2 1/4
4 1/8
Measurements are intendedfor use as reference only.Before final installation,place open and locked lidsupports in position andadjust until light box is openexactly 90 degrees.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 162/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
15. Attach bench top assembly (R, S, T) to cabinet using piano hinge. Refer to Pictorial and Figure 2.
16. Install latches on each side of cabinet and bench top assembly. Refer to Figure 2 for position.
17. Assemble leg boards (U) and (V) using glue and #8 x 2 1/2” wood screws. Refer to Pictorial and Figures 1, 2 and 8. Check for
squareness.
18. Attach leg assemblies (U, V) to bottom of table using 3” butt hinges. Leave a 1/8” gap between boards (U) and (T) when legs
are in the open position. Refer to Figure 1.
Figure 8Leg Screw Locations
3/4
U
V
3/4
19. Install a 4” barrel bolt to hold the legs in the closed position. Refer to Figure 4 for position.
20. Cut notches in cross-brace boards (W) to fit boards (V). Refer to Pictorial and Figure 1.
21. With bench top and legs in open position, attach cabinet to wall studs using 3/8 x 3 1/2” lag bolts. Refer to Figure 1. Make sure
legs are touching floor and bench top is level.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 163/203
U-BILD
Storage Bins
Plan No. 797Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of MaterialQuantity Size Material Item
1 1” x 2” x 83” pine D, N
1 1” x 3” x 171” pine E, F, H, I, M
1 1” x 8” x 40” pine G
1 1” x 10” x 122” pine C, J, K
1 1” x 12” x 171” pine A, B, L
3 7 3/4” x 11 3/4” 1/2” x 1/2” wire mesh
3 pairs 1 3/8” x 2” butt hinges
3 1” porcelain knobs
1 friction lid support
1 magnetic catch
1 box 1 1/4”
finish nails1 bottle wood glue
1 can wood filler
1 quart finish of choice
Cutting ScheduleItem Qty T W L Material
A 2 3/4” 11” 39 1/4” pine
B 3 3/4” 11” 16 1/2” pine
C 1 3/4” 16 1/2”* 39 1/4” pine
D 2 3/4” 1 1/2” 39 1/4” pine
E 1 3/4” 2” 15” pine
F 1 3/4” 2” 15” pine
G 1 3/4” 12 1/4”* 19” pine
H 6 3/4” 2” 10 7/8” pine
I 6 3/4” 2” 10 7/8” pine
J 2 3/4” 9 1/4” 13 3/8” pine
K 2 3/4” 3 3/4” 13 3/8” pineL 4 3/4” 10 7/8” 10” pine
M 2 3/4” 2” 3” pine
N 1 3/4” 1 1/4” 2 1/2” pine
*Edge-gluing required to achieve width.
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. Edge-gluing may be required to achieve the necessary width of some pieces (see Cutting Schedule).
A true country classic, this build-it-yourself storage bin
unit is a practical, convenient and attractive way to keep
apples, potatoes, onions and other fruits and vegetables
fresh and dry. The secret is the wire mesh on the front of
each of the three bins that allows air to circulate freely
around the produce.
The top shelf is flat for storing canned goods or
dish towels. The two pull-out bins below, each measuring
10 inches deep by 15 inches wide, are sized to hold plentyof fruits and vegetables. The unit adds some old-fashioned
charm to the kitchen, too.
Because the curved cuts for the lower bins and
base are traced from full-size patterns, the project is easy
enough for novices.
The project measures 40 inches tall by 19 inches
wide by 12 inches deep.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 164/203
A
D
E
M
B
F
K
L
I
H
J
C
G
Isometric
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 165/203
Side View
G
B
B
A
L
I
K
J
F
C
H
H
M M E
11”TYP.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 166/203
Front View
F
C
A
D
I
H
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 167/203
Board A
Pattern 1
Board A
Pattern 1 Position
Figure 1
Pattern 1
2” 1 1/4”
A
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 168/203
Board F
Pattern 2
Figure 2
Pattern 2
(See Front View for Position)
F
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 169/203
Figure 3
Pattern 3
Board L
Pattern 3 Position
1
1
2
2
10 7/8”
3 3/4”
10”
L
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 170/203
1. Trace Pattern 1 onto the bottom end of boards (A), cut out curves and sand. Refer to Figure 1, Side View and Isometric.
2. Trace Pattern 2 onto the bottom edge of board (F), cut out curves and sand. Refer to Figure 2 and Isometric.
3. Trace Pattern 3 onto boards (L), cut out curves and sand. Refer to Figure 3, Side View and Isometric.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 4Board B
Figure 5Boards H, I
4. Cut a 3/4” by 3/4” notch on the front cor-
ners of shelf boards (B). Refer to Figure 4.
9. Cut a 1/8” wide by 1/2” deep dado on the center of the inside edges of door
frame boards (H) and (I). Refer to Figures 5 and 6, Front View and Side View.
5. Attach shelf boards (B) to back board (C) using glue and 1 1/4” finish nails. Note: notched edges of boards (B) face the fron
of the project. Refer to Side View and Isometric.
6. Attach sides (A) to subassembly (B, C) using glue and 1 1/4” finish nails. Refer to Front View, Side View and Isometric.
7. Assemble face frame (D, E, F) using glue. Refer to Front View and Isometric.
8. Attach face frame (D, E, F) to subassembly (A, B, C) using glue and 1 1/4” finish nails. Refer to Front View, Side View and
Isometric.
3/4”
3/4” 3/4”
3/4”
C E NT E R
L I NE
1/2”
1/8”
B
H, I
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 171/203
10. Apply finish of choice to door frame boards (H) and (I).
11. Insert 7 3/4” by 11 3/4” wire mesh panels into dados
in door frame boards (H) and (I). With the wire mesh
panels in place, assemble door frame (H, I) using
glue. Refer to Figure 6 and Isometric.
12. Once door frames (H, I) are assembled, fill void
space on the ends of boards (I) with wood filler.
Refer to Figure 6.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Figure 6
Door Detail
1/8” wide by 1/2” deep dadoFill w/ woodfiller
I
H
13. Attach bin back (K) to bin bottom (J) using glue and 1 1/4” finish nails. Refer to Side View and Isometric.
14. Attach bin sides (L) to subassemblies (J, K) using glue and 1 1/4” finish nails. Refer to Side View and Isometric.
15. Attach door frames (H, I) to bin subassemblies (J, K, L) using glue and 1 1/4” finish nails. Refer to Side View and Isometric.
16. Attach cabinet top (G) to boards (A), (C) and (E) using glue and 1 1/4” finish nails. Refer to Side View and Isometric.
17. Glue boards (M) together to create a 3” wide by 2” tall by 1 1/2” thick block. Refer to Side View and Isometric.
18. Attach subassembly (M, M) to the center of and flush with the top with board of (E). Refer to Side View and Isometric.
20. Attach bins (H, I, J, K, L) and top door (H, I) to boards of (B) using 2” butt hinges. Refer to Front and Side Views.
21. Attach knobs to upper boards (H). Center knob on board. Refer to Side View.
22. Using lid support as a guide, install lid support mounting board (N) to inside of top cabinet.
23. Attach lid support to mounting board (N) and inside of top door frame (H, I). Refer to manufacturer’s instructions.
19. Sand and apply finish to the project.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 172/203
U-BILD
TV CabinetPlan No. 918Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
3 3/4” x 48” x 96” plywood A, B, C, D, L, N, Q, S, U
1 1/4” x 48” x 48” plywood X, Y
2 3/4” x 8” x 120” lumber of choice E, F, G, H, I, M, O, P, R, T, V, W, Z
1 3/4” x 3/4” x 96” moulding (see Figure 3) J, K
2 sets (right and left) 20” pocket door hardware
2 magnetic touch catches (optional)
32 3/8” x 2” dowels
1 box 1 1/4” finish nails
1 box 3/4” finish nails
1 can wood filler
1bottle wood glue1 quart finish of choice*
NOTE: Hardwood lumber sizes are provided as a base for your own calculations. Individual boards vary in appearance and defects,
which may affect your cutting layout. Also, leftover scraps can often be reglued and used for other parts.
*We used a fast-drying polyurethane clear satin finish over a medium stain.
Designed for a standard 32-inch TV (and some 36-inch TVs), this handsome television
cabinet features pocket doors for unobstructed viewing from any angle. Generous
accessory shelves will accommodate a cable or satellite decoder, a VCR or DVD play-
er, a home theater system, a video game system and more.
Overall, the television cabinet measures about 60 inches tall by 42 inches wide by 22
inches deep. The interior cabinet will accommodate a TV that measures 33 inches wide
by 33 inches tall.
Cutting Schedule
Item Qty T W L Material
N 1 3/4” 19 3/4” 33” plywood
O 2 1/4” 3/4” 19 3/4” lumber of choice
P 1 1/4” 3/4” 33 1/2” lumber of choice
Q 2 3/4” 19 3/4” 32” plywood
R 2 1/4” 3/4” 32” lumber of choice
S 1 3/4” 19 3/4” 9 1/4” plywood
T 1 1/4” 3/4” 9 1/4” lumber of choice
U 1 3/4” 5 1/4” 32” plywood
V 6 3/4” 2” 14 7/8” lumber of choice
W 4 3/4” 2” 50 1/16” lumber of choice
X 2 1/4” 15 5/8” 31 11/16” plywood
Y 2 1/4” 15 5/8” 13 7/8” plywood
Z 4 3/4” 1 1/4” 20 1/2” lumber of choice
Item Qty T W L Material
A 2 3/4” 21 1/4” 59 1/4” plywood
B 1 3/4” 40 1/2” 59 1/4” plywood
C 1 3/4” 22” 42” plywood
D 1 3/4” 20 1/2” 40 1/2” plywood
E 1 3/4” 2 3/4” 38” lumber of choice
F 1 3/4” 2” 38” lumber of choice
G 2 3/4” 2” 59 1/4” lumber of choice
H 2 3/4” 1 11/16” 23 11/16” moulding
I 1 3/4” 1 11/16” 45 3/8” moulding
J 2 3/4” 3/4” 22 3/4” moulding
K 1 3/4” 3/4” 43 1/2” moulding
L 2 3/4” 19 3/4” 16” plywood
M 2 1/4” 3/4” 16” lumber of choice
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 173/203
1/4” x 48” x 48”Plywood Cutting Layout
3/4” x 48” x 96”Plywood Cutting Layouts
A
U
Q
Q
B
C D
L L N S
A
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. We used maple for this project, but oak, pine or birch will work equally well.
4. If you choose to install magnetic touch catches on the project, attach a 2” x 4” mounting block to the center
of the back side and flush with the bottom of board (E).
5. Once the project is finished, back panel (B) may require a cut-out to accommodate your television.
Y
Y
X
X
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 174/203
Isometric
C
E
G
G
Z
Z
A
A
B
V
V
V
V
V
Y
Y
U
N
L
M
O
O
L
T
R
R
Q
Q
S
W
W
W
W
V
XX
D
F
H, J
I, K
H, J
M
P
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 175/203
Figure 1Front, Side & Top Views
15 1/8”
A
G
E
V
V
V
W W
B
D D
U
X
G G
F
Y
A
E
A
A
Z
B
Z
H
EC Z
B
I C CH I
I
JK
K
S, T
Q, R
Q, R
L, M
U
N, P O N
Q
Q
6 1/4”
TV stand not shown in this view.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 176/203
1. Attach sides (A) to back (B) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 1.
2. Attach top (C) to subassembly (A, B) using glue and 1 1/4” finish nails. Check for squareness. Refer to Isometric and Figure 1
3. Attach bottom (D) to subassembly (A, B, C) using glue and 1 1/4” finish nails. Check for squareness. Refer to Isometric and
Figures 1 and 2 .
4. Cut legs on boards (G). Refer to Figure 2.
5. Assemble face frame boards (E), (F) and (G) using glue and 3/8” dowels. Check for squareness. Refer to Isometric and Figures
1 and 2.
6. Attach face frame (E, F, G) to cabinet subassembly (A, B,C, D) using glue and 1 1/4” finish nails. Check for squareness. Refer
to Isometric and Figure 1.
7. Attach moulding (H), (I), (J) and (K) to cabinet using glue
and clamps. Refer to Isometric and Figures 1 and 3.
Figure 2Leg Pattern
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
4 1/4”
1 1/4”
G
A
D
F
Figure 3Moulding Pattern
3/4”
1/4”
H, I
J, K
C 20
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 177/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
8. Attach trim strips (M) to side boards (L) using glue and 3/4” finish nails. Refer to Isometric and Figure 1.
9. Attach trim strips (O) and (P) to top board (N) using glue and 3/4” finish nails. Refer to Isometric and Figure 1.
10. Attach trim strips (R) to shelf and bottom boards (Q) using glue and 3/4” finish nails. Refer to Isometric and Figure 1.
11. Attach trim strip (T) to divider board (S) using glue and 3/4” finish nails. Refer to Isometric and Figure 1.
12. Attach sides (L, M) to top (N, O, P) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 1.
14. Attach divider (S, T) to the center of the underside of shelf (Q, R) using glue and 1 1/4” finish nails. Refer to Isometric and
Figure 1.
15. Insert shelf and divider subassembly (Q, R, S, T) into box subassembly (L, M, N, O, P, Q, R) and attach to sides (L, M) and
bottom (Q, R) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 1.
16. Insert shear board (U) between top (N, O, P) and shelf (Q, R) and attach to sides, top and shelf using glue and 1 1/4” finish
nails. Refer to Isometric and Figure 1.
17. Assemble door frame boards (V) and (W) using glue and
3/8” dowels. Check for squareness. Refer to Isometric and
Figures 1 and 4.
18. Cut a 3/8” wide by 1/4” deep rabbet on the inside back edges
of door frames (V, W). Refer to Isometric and Figure 4.
13. Attach bottom (Q, R) to sides (L, M) using glue and 1 1/4” finish nails. Refer to Isometric and Figure 1.
Note: Steps 8 though 16 apply to the TV stand only.
Figure 4Door Frame Construction
W
V
3/8” wide by1/4” deep rabbet.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 178/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
20. Sand cabinet, doors and TV stand.
21. Apply finish to cabinet, doors and TV stand.
22. Using pocket door hardware to determine position, install hardware mounting boards (Z) to the inside of sides (A).
25. If necessary, using your TV set as a guide determine size and position of hole to cut in back (B).
23. Install pocket door hardware on doors (V, W, X, Y) and hardware mounting boards (Z) per manufacturer’s instructions.
24. Place TV stand inside cabinet.
19. Insert door panels (X) and (Y) into rabbets in back side of door frames and attach using glue and clamps. Refer to Isometric
and Figure 1.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 179/203
Three-Piece Bedroom SetPlan No. 768Copyright U-Build, Inc., 2004.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
1 3/4” x 48” x 96” oak plywood
1 1/2” x 48” x 96” mahogany plywood
1 1/2” x 48” x 48” mahogany plywood
2 1/8” x 48” x 96” masonite
1 1/8” x 48” x 48” masonite
27 bd ft.* 3/4” oak 22 bd ft.* 3/4” pine
7 72” “J” molding**
15 pairs 14” drawer guides
1 box 1 1/4” finish nails
1 bottle wood glue
30 1” flathead wood screws
88 3/8” x 2” dowel pins
as needed finish of choice
*Due to varied stock sizes available, knot patterns and defects in lumber, it is
impossible to give actual board sizes. Be sure to check longest lengths of
finished boards when considering lumber to purchase.**See Figure 3.
Here’s a great project for do-it-yourselfers who are tired of that old bedroomfurniture. The three-piece set features a handsome oak finish and clean linesthat blend well with any decor.
The finished dresser measures about 60 inches wide by 32 inches tall, thechest of drawers stands 32 inches high by 30 inches wide and the nightstand isabout 20 inches wide by 22 inches tall. All three pieces are 16 inches deep.
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. We used oak for this project, but pine or birch will work equally well.
4. Edge-gluing may be required to achieve the necessary width of some pieces.
5. When using finish nails on oak, drill pilot holes in the boards to be nailed.
6. The drawer was designed for drawer guides that require 1/2” of clearance on both sides.
7. The project as pictured was stained with a medium oak color.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 180/203
Cutting Schedule--Dresser
Item Qty T W L MaterialA 2 3/4” 15 1/2” 31 9/16” oak plywoodB 4 1/4” 3/4” 15 1/2” oak C 4 1/4” 3/4” 32 1/16” oak D 1 3/4” 15 1/2” 57 3/4” oak plywoodE 2 1/4” 3/4” 57 3/4” oak F 1 3/4” 3 1/4” 57 3/4” oak G 1 3/4” 2” 57 3/4” oak
H 1 3/4” 4” 57 3/4” pineI 2 1/8” 29” 27 13/16” masoniteJ 12 3/4” 2” 28 1/2” pineK 12 3/4” 2” 11 1/8” pineL 16 1/2” 5 5/8” 14 7/8” mahogany plywoodM 16 1/2” 5 1/8” 26 1/2” mahogany plywoodN 8 1/8” 14 7/8” 27” masoniteO 8 3/4” 5 1/4” 28 3/8” oak P 8 3/4” 1 1/2” 28 3/8” oak “J” moldingQ 1 3/4” 15 3/4” 31 5/16” pineR 1 1/4” 3/4” 27 5/16” oak
Cutting Schedule--Chest of Drawers
Item Qty T W L MaterialA 2 3/4” 15 1/2” 31 9/16” oak plywoodB 4 1/4” 3/4” 15 1/2” oak C 4 1/4” 3/4” 32 1/16” oak D 1 3/4” 15 1/2” 28 1/2” oak plywoodE 2 1/4” 3/4” 28 1/2” oak F 1 3/4” 3 1/4” 28 1/2” oak G 1 3/4” 2” 28 1/2” oak H 1 3/4” 4” 28 1/2” pineI 1 1/8” 29” 27 13/16” masoniteJ 6 3/4” 2” 28 1/2” pineK 6 3/4” 2” 11 1/8” pineL 8 1/2” 5 5/8” 14 7/8” mahogany plywoodM 8 1/2” 5 1/8” 26 1/2” mahogany plywoodN 4 1/8” 14 7/8” 27” masoniteO 4 3/4” 5 1/4” 28 3/8” oak P 4 3/4” 1 1/2” 28 3/8” oak “J” molding
Cutting Schedule--Nightstand
Item Qty T W L MaterialA 2 3/4” 15 1/2” 21” oak plywoodB 4 1/4” 3/4” 15 1/2” oak
C 4 1/4” 3/4” 21 1/2” oak D 1 3/4” 15 1/2” 18” oak plywoodE 2 1/4” 3/4” 18” oak F 1 3/4” 3 1/4” 18” oak G 1 3/4” 2” 18” oak H 1 3/4” 4” 18” pineI 1 1/8” 18 1/2” 17 1/4” masoniteJ 4 3/4” 2” 18” pineK 4 3/4” 2” 11 1/8” pineL 6 1/2” 4 3/8” 14 7/8” mahogany plywoodM 6 1/2” 3 7/8” 16” mahogany plywoodN 3 1/8” 14 7/8” 16 1/2” masoniteO 3 3/4” 4” 17 7/8” oak P 3 3/4” 1 1/2” 17 7/8” oak “J” molding
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 181/203
1/8” MasoniteCutting Layouts
1/2” PlywoodCutting Layouts
3/4” PlywoodCutting Layouts
ANightstand
ANightstand
ADresser
IDresser
NDresser
NDresser
NDresser
NDresser
NDresser
NDresser
NDresser
NDresser
IDresser
ADresser
DDresser
AChest
AChest
IChest
NChest
NChest
NChest
NChest
M Chest L Chest
L Chest
L Chest
L Chest
L Chest
L Chest
L Chest
L Chest
M Dresser
M Dresser
M Dresser
M Dresser
M Dresser
MDresser
M Dresser
M Dresser
M Dresser L Nightstand
L Nightstand
L Nightstand
L Nightstand
L Nightstand
L Nightstand
M Nightstand M Nightstand M Nightstand M Nightstand M Nightstand
M Nightstand
M Dresser
M Dresser
M Dresser
M Dresser
MDresser
M Dresser
M Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
L Dresser
M Chest
M Chest
M Chest
M Chest
MChest
M Chest
M Chest
DChest
DNightstand
NNightstand
INightstand
NNightstand
NNightstand
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 182/203
Pictorial
(Dresser)
Section A-A
D
EB
A
A
A
C
FE E
D
J J
F
G
H
G
Q
R
H
J
K
I
6 13/16”
13 5/8”
20 7/1
K
I
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 183/203
Section B-B
E E
D
J J
F
G
H
6 13/16”
13 5/8”
20 7/16
K
I
Pictorial
(Chest of Drawers)
D
EB
A
B
B
C
F
G
HJ
K
I
Section C-C
E E
DJ J
F
G
H
5 9/16”
11 1/8”
K
I
D
EB
A
C
C
CF
G
H
J
K
IPictorial
(Nightstand)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 184/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Figure 1Boards J and K
Figure 2Boards L and M
1. Attach trim boards (B), (C) and (E) to edges of sides (A) and top (D) using glue and 1 1/4” finish nails. Attach trim board (R)
to front edge of center divider (Q) using glue and 1 1/4 ” finish nails. Refer to Pictorials and Sectional Drawings.
2. Attach side subassemblies (A, B, C) to top subassembly (D, E) using glue and 1 1/4” finish nails. Attach center divider sub-
assembly (Q, R) to top subassembly (D, E) using glue and 1 1/4” finish nails. Refer to Pictorials and Sectional Drawings.
3. Assemble bottom front frame boards (F) and (G) using glue and 1 1/4” finish nails. Refer to Pictorials and Sectional Drawings
4. Attach bottom front frame subassembly (F, G) and bottom back frame board (H) between side assemblies (A, B, C) using glue
and 1 1/4” finish nails. For the dresser only, attach bottom front frame subassemblies (F, G) and bottom back frame boards (H)
between side assemblies (A, B, C) and center divider subassembly (Q, R) using glue and 1 1/4” finish nails. Refer to Pictorials
and Sectional Drawings.
5. Route a 3/8” wide by 1/8” deep rabbet around the inside back edges of cabinet for back (I). Refer to Pictorials and Sectional
Drawings.
6. Assemble support frames (J, K) using glue and 3/8” dowels. Refer to Figure 1, Pictorials and
Sectional Drawings.
8. Route a 1/8” wide by 1/4” deep dado on the inside of boards (L). Refer to Figures
2 and 4.
7. Attach support frames (J, K) to cabinet using glue and 1 1/4” finish nails. Check for squareness. Refer to Pictorials and Sectional
Drawings.
J
LN
K
1/4”
1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 185/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
11. Assemble drawer boxes (L, M, N) usi
glue and 1 1/4” finish nails. Check f
squareness. Attach drawer fronts (O,
from inside using two 1” flathead woo
screws. Bottom edge of drawer fro
should be flush with bottom edges boards (L). Refer to Figure 4.
12. Attach drawer guides to cabinet and drawer boxes. Refer to manufacturer’s instructions.
13. Attach back (I) to cabinet using 1 1/4” finish nails. Refer to Pictorials and Sectional Drawings.
10. Assemble drawer fronts (O, P) using glue. Refer to Figure 3.
M
N
P
OM
L
L
Figure 4Drawer Contsruction
Figure 3Drawer Front Contsruction
OO
P
Optional do-it-yourselfpull molding. Pre-drilland assemble with 1/2”brads.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 186/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Three
14. Sand and apply finish to cabinet and drawer fronts.
15. Install drawers.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 187/203
Tiered PlanterPlan No. 562Copyright U-Build, Inc., 2000.
All rights reserved. Printed in the U.S.A.
NOTES1. Check materials before beginning work.
2. Read manufacturer’s instructions before operating
equipment.
3. Always wear safety glasses.
4. Cut pieces to size following the Cutting Schedule.
Assemble using galvanized nails according to diagrams
at right.
This tiered planter is great for colorful perennials or trailing plants like strawberries. Made from redwood, cedar
or pine, the project is simple and inexpensive to build. It calls for standard lumber, galvanized nails, sandpaper and
sealer. Construction is a simple matter of cutting the pieces to size and assembling with galvanized nails. To finish,
sand and apply a coat of sealer or paint.
The tiered planter is about 30 inches square by 14 inches tall.
Bill of Materials*
Quantity Size Material Item
32 linear feet 2” x 6” redwood, cedar, pine A, B, C, D, E
5 linear feet 2” x 4” redwood, cedar, pine F
1 box #10 galvanized nails
1 quart suitable finish
*Dimensions given are for standard lumber call-outs
Cutting Schedule*
Part Qty T W L Material
A 4 1 1/2” 5 1/2” 18” redwood, cedar, pine
B 4 1 1/2” 5 1/2” 15” redwood, cedar, pine
C 2 1 1/2” 5 1/2” 27 1/2” redwood, cedar, pine
D 2 1 1/2” 5 1/2” 24 1/2” redwood, cedar, pine
E 5 1 1/2” 5 1/2” 27 1/2” redwood, cedar, pine
F 2 1 1/2” 3 1/2” 27 1/2” redwood, cedar, pine
*Dimensions given are actual
A
AA
A
A
E
E
E
E
E
E
E
E
E
F
F
F
F
C
C
D D
D
B
B
B
B
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 188/203
U-BILD
Two-Door Ice Box
Plan No. 686Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material
10 3/4” x 6” x 96”* oak
1 1/8” x 48” x 48” oak plywood
60 3/8” x 2” dowels
1 small box 1 1/4” finish nails
1 small bottle wood glue
1 small can oil or stain
6 brass ice box hinges
2 brass ice box handles
1 brass top lid handle
*approximately 40 board feet
NOTES1. Read all instructions and check materials before
beginning work.
2. Read manufacturer’s instructions before operat-
ing equipment.
3. Oak is preferred for this project.
4. Edge-gluing is required to achieve the necessary
width of boards F, H, N, X, AA and EE.
5. When using finish nails on oak, drill pilot holesto avoid splitting.
6. Always wear safety glasses.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes rema
popular with collectors, even though they’re expensive and hard to find.
This do-it-yourself version is neither: it’s both inexpensive and easy to build. A
authentic reproduction of an original, the project is especially popular when used as
bar, but it has many other uses. The top opens up to reveal a convenient storage are
and the lower cabinet features two compartments perfect for glassware and other fra
ile items.
The ice box measures 38 inches high by 24 inches wide by 16 inches deep.
Item Qty T W L Material
A 2 3/4” 3” 35 1/4” oak
B 2 3/4” 2 1/4” 35 1/4” oak
C 2 3/4” 3” 10” oak
D 2 3/4” 2” 10” oak
E 2 3/4”
4”
10”
oak F 2 3/4” 10” 11 1/4” oak
G 2 1/8” 10 1/2” 11 3/4” oak plywood
H 2 3/4” 10” 15” oak
I 2 1/8” 10 1/2” 15 1/2” oak plywood
J 2 3/4” 3” 35 1/4” oak
K 1 3/4” 3” 18” oak
L 1 3/4” 2” 18” oak
M 1 3/4” 4” 18” oak
N 3 3/4” 15 1/8” 22 1/2” oak
O 1 3/4” 2 1/4” 22 1/2” oak
P 1 3/4” 2” 24” oak
Item Qty T W L Material
Q 2 3/4” 4” 16 3/4” oak
R 1 3/4” 4” 25 1/2” oak
S 1 1/8” 23 1/4” 37 1/4” oak plywood
T 2 3/4” 2” 12 3/4” oak
U 2 3/4”
2”
25 1/2”
oak V 2 3/8” 3/4” 16 3/8” oak
W 1 3/8” 3/4” 24 3/4” oak
X 1 3/4” 13 3/8” 22 1/8” oak
Y 2 3/4” 2” 14 5/8” oak
Z 2 3/4” 2” 11 7/8” oak
AA 1 3/4” 7 7/8” 14 5/8” oak
BB 1 1/8” 8 3/8” 15 1/8” oak plywood
CC 2 3/4” 2” 14 5/8” oak
DD 2 3/4” 2” 15 5/8” oak
EE 1 3/4” 11 5/8” 14 5/8” oak
FF 1 1/8” 12 1/8” 15 1/8” oak plywood
Cutting Schedule
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 189/203
IsometricNote that Parts G, P and BB
do not appear on this drawing.
X
A
C
C
B
BA
U
S
C
A
B
J
J
F
D
H
I
E
Q
R
M
N
Q
U
W
N
NZ
Y
Y
L
Z
AA
K
O
T
T
V
45 DEGREE
MITER CUT. Lower Door
DD DD
CC
EE
FF
CC
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 190/203
Section A-A Section B-B
Section C-C
X X
N
N
N
P
R
M
L
Y
Y
AA
CC
CC
EE
U
O K
W
UT
C
V
N
F
G
D
H
N
FA B
J
Z
E
Q
N
BB
FF
I
S
S G
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 191/203
Front
Back
Raised center panel
F, H, AA, EE(See Figure 2)
Typical location of dowelsin parts A, B, C, D, E, J, K,
L, M,T, U,Y, Z, CC and DD
1/4” wide by 1/8” deeprabbet
Round-over this edge
of doors
Run a 3/8”
x 3/8” rab-
bet aroundthis edge
of doors
1/8” plywood panel
Detail 1Door & Side Panel Construction
Figure 1End View of Top Lid X
Showing Annular Rings Reversed
Figure 2
F
A S
G
Figure 3
Optional Decorative Cutsfor Raised Center Panels
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 192/203
3. Mark location for dowels in pieces A, B, C, D, E, J, K, L, M, T, U, Y, Z, CC and DD and drill 3/8” holes for dowels. Refer to
Detail 1.
1. Construct top lid X using three pieces of lumber, reversing direction of the grain and gluing and clamping (this will minimize
warping). See Figure 1. Allow glue-up to dry thoroughly.
2. Round-over all four top edges and run a 3/8” x 3/8” rabbet around all four bottom edges of board X. See Sections A-A and B-B.
4. Assemble and clamp face frame, side frames and door frames using 3/8” dowels and wood glue. Check for squareness. Refer
to Isometric.
5. Rout a 1/4” wide by 1/8” deep rabbet around the inside edges of the openings in side panels and door frames to accommodate
1/8” plywood. See Sections A-A, B-B and C-C and Detail 1.
7. Glue 1/8” plywood panels to inside side and door frames (do not use nails). See Detail 1.
8. Using your router, create raised center panels F, H, AA and EE. See Figure 3.
6. Cut a 1/8” deep by 3/8” wide rabbet inside back edge of side panel frames. See Figure 2.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly Instructions
10. Nail and glue side panels to shelves N (see Note 5). Refer to Sections A-A and B-B for position. Check for squareness.
11. Attach face frame J, K, L and M to cabinet using 1 1/4” finish nails and glue. Refer to Isometric.
12. Round-over top edges of base boards Q and R (see Section A-A and B-B). Attach boards Q and R to cabinet using 1 1/4” fin-
ish nails and glue. Refer to Isometric and Sections A-A and B-B.
9. Glue raised center panels to 1/8” plywood inserts (do not use nails). See Isometric, Sections A-A and B-B and Detail 1.
13. Attach boards O and P to side frames using 1 1/4” finish nails and glue. Refer to Section B-B.
14. Round-over bottom edges of boards V and W. Align top frame T and U and molding V and W and attach using 1 1/4” finish
nails and glue. Refer to Isometric and Sections A-A and B-B.
15. Nail plywood S to back of unit. Refer to Sections B-B and C-C.
16. Round-over all four edges of boards Y, Z, CC and DD on the outside of the doors. Run a 3/8” x 3/8” rabbet around all four edges of
boards Y, Z, CC and DD on the inside of the doors so that doors sit 3/8” into frames. Refer to Sections A-A and B-B and Detail 1.
17. Sand and stain the project.
18. Attach top lid and doors using brass ice box hardware.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 193/203
Wall UnitPlan No. 648Copyright U-Build, Inc., 2003.
All rights reserved. Printed in the U.S.A.
These modular wall units are an ideal way to make
the most of valuable wall space. Any number of the
two units may be combined to take advantage of any
floor plan.
Both units measure 78 inches tall by 16 inches
deep. The unit on the left measures 30 inches wide,and the unit on the right measures 36 inches wide.
NOTES1. Read manufacturer’s instructions before operating equipment.
2. Always wear safety glasses.
3. We used cedar for this project, but almost any lumber (such as oak, pine or poplar) will work equally well.
Illustration 1
Typical Wall Unit System
The strength of this project lies in its versatil-
ity, as any number of units may be combined
to effectively utilize any space. The system
pictured at left, which consists of two 36” units
(one with a cabinet and one with shelves only)
and one 30” unit with a desk, is just one possi-
ble combination out of hundreds. Use the
individual materials lists and cutting schedules
to create the modular components that work
best for you.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 194/203
30” Unit(Board G requires edge-gluing to achieve width)
Item Qty T W L Material
A 4 3/4” 3 3/4” 78” lumber of choice
B 4 3/4” 3 3/8” 78” lumber of choice
C 2 3/4” 3” 28 1/2” lumber of choice
D 2 3/4” 4” 28 1/2” lumber of choice
E 2 3/4” 3” 13” lumber of choice
F 2 3/4” 4” 13” lumber of choice
G 3/4” 14 1/4” 28 1/4” lumber of choice
36” Unit(Board G requires edge-gluing to achieve width)
Item Qty T W L Material
A 4 3/4” 3 3/4” 78” lumber of choice
B 4 3/4” 3 3/8” 78” lumber of choice
C 2 3/4” 3” 34 1/2” lumber of choice
D 2 3/4” 4” 34 1/2” lumber of choice
E 2 3/4” 3” 13” lumber of choice
F 2 3/4” 4” 13” lumber of choice
G 3/4” 14 1/4” 34 1/4” lumber of choice
Desk(Boards A, B, C and F require edge-gluing to achieve width)
Item Qty T W L Material
A 1 3/4” 13 1/2” 28 1/4” lumber of choice
B 1 3/4” 13 1/2” 27 1/2” lumber of choice
C 2 3/4” 13 1/2” 17 3/8” lumber of choice
D 1 1/4” 17” 27 1/2” plywood
E 2 3/4” 2 7/8” 17 3/4” lumber of choice
F 2 3/4” 17” 22 3/8” lumber of choice
G 2 3/4” 3/4” 3” lumber of choice
Cabinet(Boards A, B, C and F require edge-gluing to achieve width)
Item Qty T W L Material
A 1 3/4” 13 1/2” 34 1/4” lumber of choice
B 1 3/4” 13 1/2” 33 1/2” lumber of choice
C 2 3/4” 13 1/2” 23 5/8” lumber of choice
D 1 1/4” 23 1/4” 33 1/2” plywood
E 2 3/4” 2 7/8” 24” lumber of choice
F 2 3/4” 14 3/16”* 24” lumber of choice
G 2 3/4” 3/4” 3” lumber of choice*Dimension given is slightly oversize. Trim doors to fit.
Cutting Schedule
30” Unit
Quantity Size Material
5 3/4” x 8” x 7’ lumber of choice
2 per shelf 3/4” x 8” x 30” lumber of choice
32 1 1/4” flat head wood screws1 box 1 1/4” finish nails
1 bottle wood glue
4 5/8” x 3/16” x 72” steel shelf standards
4 per shelf 5/8” steel bracket clips
Desk
Quantity Size Material
2 3/4” x 8” x 8’ lumber of choice
1 3/4” x 6” x 10’ lumber of choice
1 1/4” x 20” x 30” plywood
2 1 1/2” butt hinges
30” chain
2 screw eyes
1 box 1” finish nails
1 bottle wood glue
Cabinet
Quantity Size Material
2 3/4” x 8” x 7’ lumber of choice
2 3/4” x 8” x 10’ lumber of choice1 1/4” x 24” x 36” plywood
4 1 1/2” butt hinges
1 box 1” finish nails
1 bottle wood glue
36” Unit
Quantity Size Material
4 3/4” x 8” x 7’ lumber of choice
1 3/4” x 8” x 8’ lumber of choice
2 per shelf 3/4” x 8” x 36” lumber of choice32 1 1/4” flat head wood screws
1 box 1 1/4” finish nails
1 bottle wood glue
4 5/8” x 3/16” x 72” steel shelf standards
4 per shelf 5/8” steel bracket clips
Bill of Material
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 195/203
C
B
B
B
B
A
A
A
A
D
D
DF
B
E C
B A A
F
F
C
E
E Figure 1Basic Frame Construction
(30” and 36” widths)
78”
16” See Figure 4
See Figure 5
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 196/203
A
D
D
C
C
E
E
F
FC F E
C
C
D
F
A
A
E
F
A
B
G
G
C
C
E
C
G
G
A
B
B
E
E
B
Figure 2
Desk Construction(for 30” unit)
Figure 3
Cabinet Construction(for 36” unit)
E
28 1/4”
17 3/4”
Cut mortises to accommodatebutt hinges.
Once hinges are installed,
position desk lid as pic-tured, attach screw eyesand adjust length of chain.
24
14 1/8” 14 1/4”
14 1/4”
3”
AD
D
8”
34 1/4”
2 3/8”
17 1/8”
Cut mortises to accommodatebutt hinges.
Left door not pictured.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 197/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
Note: Steps 1 though 6 apply to the basic frame unit only.
1. Cut 3/8” deep by 3/4” wide rabbets in frame boards (A).
Refer to Figures 1 and 4.
2. Cut 1/4” deep by 5/8” wide dados along the entire length
of frame boards (B) to accommodate shelf standards.
Refer to Figures 1 and 4.
3. Using glue and 1 1/4” finish nails, attach boards (A) to
boards (B) to form upright corners. Refer to Figures 1
and 4.
4. Cut optional 1” radius on top outside corners of subassemblies
(A, B) if desired. Refer to Figure 5.
5. Cut optional 1/4” radius on outside corners of subassemblies
(A, B) if desired. Refer to Figure 4.
6. Attach top and bottom cross braces (C) and (D) to corner sub-
assemblies (A,B) using glue and 1 1/4” finish nails. Refer to
Figures 1, 4 and 5.
Figure 4
Frame Construction Detail, Top View
A
C
E
B
2”
Shelf
Standard
Figure 5Frame Construction Detail, Front View
A
C
E
R 1”
R 1/4” R 1/4”
R 1/4”
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 198/203
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
Note: Steps 7 though 13 apply to the desk & cabinet only.
7. Cut 3/8” deep by 3/4” wide rabbets in both ends of top board (A) and and one end of side boards (C). Refer to Figures 2 and 3
8. Attach top board (A) to side boards (C) using glue and 1” finish nails. Refer to Figures 2 and 3.
9. Attach bottom board (B) to subassembly (A, C) using glue and 1” finish nails. Refer to Figures 2 and 3.
10. Cut a 1/4” deep by 3/8” wide rabbet around inside back edge of subassembly (A, B, C). Refer to Figures 2 and 3.
11. Attach back (D) to subassembly (A, B, C) using glue and 1” finish nails. Refer to Figures 2 and 3.
12. Attach face frames (E) to subassembly (A, B, C, D) using glue and 1” finish nails. Refer to Figures 2 and 3.
13. Install desk lid (F) or cabinet doors (F). Refer to Figure 2 or 3.
14. Place completed desk or cabinet (if desired) between front and back frame subassemblies (A, B, C, D). Refer to Illustration 1
15. Connect front and back frame subassemblies (A, B, C, D) with side braces (E) and (F) using two 1 1/4” flat head wood screws
at each joint. Refer to Figures 1 and 4.
16. Determine desired position of desk or cabinet (refer to illustration 1), mount shelf bracket clips in shelf standards and place
unit(s) in position. Height of desk or cabinet may be adjusted by moving shelf bracket clips up or down.
17. Mount bracket clips in desired position and install shelves (G). Shelves may be adjusted by moving shelf bracket clips up or
down.
18. Apply desired finish.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 199/203
Woodworking
BenchPlan No. 866Copyright U-Build, Inc., 1998.
All rights reserved. Printed in the U.S.A.
Bill of Material
Quantity Size Material Item
1 1 1/2” x 5 1/2” x 6’ Douglas Fir A, K2 1 1/2” x 5 1/2” x 10’ Douglas Fir A
7 1 1/2” x 3 1/2” x 8’ Douglas Fir B, C, D, E,
F, G, H, I
1 1/2” x 24” x 6’ Plywood
16 3/8” x 2” Dowel Pins
22 #10 x 1 1/2” Flat head Phillips Wood Screws
73 #10 x 1 1/2” Flat head Phillips Wood Screws
8 5/16” x 3 1/2” Carriage Bolts, Washers, Nuts
1 small bottle Wood Glue
1 quart Finish
Cutting Schedule
Part Qty T W L Material
A 5 1 1/2” 5 1/4” 60” Douglas FiB 2 1 1/2” 3 1/2” 26 1/4” Douglas Fi
C 2 1 1/2” 3 1/2” 53” Douglas Fi
D 1 1 1/2” 3 1/2” 19 1/4” Douglas Fi
E 4 1 1/2” 3 1/2” 34 1/2” Douglas Fi
F 2 1 1/2” 3 1/2” 26 1/4” Douglas Fi
G 2 1 1/2” 3 1/2” 24” Douglas Fi
H 3 1 1/2” 3 1/2” 19 1/4” Douglas Fi
I 2 1 1/2” 3 1/2” 53” Douglas Fi
J 1 1/2” 22 1/4” 50” Plywood
K 1 1 1/2” 5 1/2” 10” Douglas Fi
Any experienced woodworker can attest to the fact that a good workbench is one of the keys to success for any project.
More than a simple work surface, a well-made woodworking bench incorporates precise angles and a level top that serve
as gauges for other projects.This do-it-yourself version features a heavy laminated top, a convenient storage bin underneath and a design that allows
for a precision woodworking vise and bench stop.
The completed bench measures about 36 inches tall by 26 inches wide by 60 inches long, and is designed to fit a vise
with a 4- by 7-inch jaw.
NOTES
1. Select quality dry lumber to build your workbench. Lumber that has a high moisture content will
have a tendency to shrink and warp.
2. Board K is used to mount your bench vise. I chose to mount the vise on the right front corner of
the bench. You may choose a different location that may be more convenient or comfortable for
yourself.
3. I chose a fast-drying polyurethane clear satin finish. Give your project at least two coats. For a
higher quality finished project, apply finish before final assembly.
4. Take care in the clamping process for the table top. Lumber must be square and flat to ensure a
quality working surface when your project is finished.
5. Read manufacturer’s instructions before operating equipment.
6. Always wear safety glasses.
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 200/203
F
F
E
E
C
H
H
I
I
H
J
A
G
B
E
Isometric(Boards D and K not shown)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 201/203
60
26 1/4
12
5 1/4
17
36
AAD
G G
I
J
F
E E
F
B C B B
G
H
E
1 TYP.
E
F
A
A
C
C
E E
EE
B
B
D
K
1 1/2
6 1/8 TYP.
8 1/2 TYP.
1 3/4
6
1 TYP.
1 TYP.
Figure 2Figure 1
Figure 3(Top View of Table)
Figure 3(Bottom View of Table)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 202/203
2. Attach boards B, C and D to underside of bench top with #10 x 2 1/2” wood screws (see Figure 4). Notch one of the C boards for
bench vise at this time (optional).
3. Assemble legs from boards E and F with 5/16” x 2” carriage bolts (see Figures 5 and 6). Attach leg assemblies to boards B using
#10 x 2 1/2” wood screws.
4. Bolt boards H to boards E (see Figure 2). Check assemblies for squareness.
5. Drill and attach diagonal braces G to boards C and E with #10 x 2 1/2” wood screws (see Figure 7). Squareness is a must.
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage One
1. Resaw 2 x 6 lumber to eliminate the radius on the edges. Using at least four equally spaced dowel pins between each board, glue
and clamp lumber to form benchtop (see Figure 3). Check for flatness.
1 3/4
1 3/4
1 3/4
3/4
1
13 3/4
3/8 DIA.
3/16 DIA.5 1/4
Figure 5
(Board E)
Figure 6
(Board F)
3/8 DIA.
45o
2 15/16
1
3/4
3/16 DIA.
Figure 7(Board G)
8/22/2019 Conjunto de planos constructivos de muebles y otros objetos
http://slidepdf.com/reader/full/conjunto-de-planos-constructivos-de-muebles-y-otros-objetos 203/203
6. Use #10 x 2 1/2” wood screws to attach I to H and J to H and I (see Figures 8, 9 and 10).
Read all instructions before beginning any work. Cut all material to sizes shown in cutting schedule.
Assembly InstructionsPage Two
3/8 DIA.
1 3/4
2 1/4
3/4
26 1/2
top related