esparragos y tornillos catalogo tecnico

131

Upload: mgsaya

Post on 10-Oct-2014

1.684 views

Category:

Documents


14 download

TRANSCRIPT

Page 1: Esparragos y Tornillos Catalogo Tecnico
Page 2: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

ÍNDICE / INDEX

1. Espárragos / Studbolts ANSI/DIN 2

2. Tornillos / Bolts ANSI/DIN 37

3. Tuercas / Nuts ANSI/DIN 52

4. Arandelas / Washers DIN 60

5. Juntas / Gaskets ASME/DIN 65

6. Datos técnicos 86

7. Tablas útiles / Useful charts 107

8. Technical Data 121

Este catálogo es continuación a los anteriores creados por DIMECO T.I. revisado en cuanto a la normativa actual

This catalogue is a follow up of the previous ones issued by DIMECO T.I. The same has been revisedaccording to the current applicable standards

www.dimecoti.com

edición 2008

Page 3: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

EspárragosStudbolts

ANSI/DIN

2DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

Page 4: Esparragos y Tornillos Catalogo Tecnico

3DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

FERRITIC STEEL AUSTENITIC STEEL

B5 B6 B7 B7M B16 B8 B8M B8T B8C

AISI 501 410 4140 304 316 321 347

DIN12CrMo

19-5X10Cr13 42CrMo4

24CrMo V55

X5CrNi 18-8

X5CrNiMo 17-12-2

X6CrNiTi 18-10

X6CrNiNb 18-10

W.-Nr. 1.7362 1.4006 1.7225 1.7711 1.4301 1.4401 1.4541 1.4550

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTS

C % 0,10 min 0,08-0,15 0,37-0,49 0,36-0,47 0,08 max. 0,08 max. 0,08 max. 0,08 max.

Mn % 1 max. 1 max. 0,65-1,10 0,45-0,70 2 max. 2 max. 2 max. 2 max.

Si % 1 max. 1 max. 0,15-0,35 0,15-0,35 1 max. 1 max. 1 max. 1 max.

P max.% 0,040 0,040 0,035 0,035 0,045 0,045 0,045 0,045

S max.% 0,030 0,030 0,040 0,040 0,030 0,030 0,030 0,030

Cr % 4-6 11,5-13,5 0,75-1,20 0,80-1,15 18-20 16-18 17-19 17-19

Ni % 8-11 10-14 9-12 9-12

Mo % 0,40-0,65 0,15-0.25 0,50-0,65 2-3

V % 0,25-0,35

Al Max. % 0,015

TI %5x(C+N) min.0,70 max.

Cb+Ta10xC min. 1,10 max.

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTS

Diameter up to 4" up to 4"2 1/2"

and under2 1/2"

and under2 1/2"

and underClass 1: all Diameters

T.S.min. Mpa 690 760 860 690 860 515 515 515 515

Y.S min. 0.2% Mpa 550 585 720 550 725 205 205 205 205

Elongation min.% 16 15 16 18 18 30 30 30 30

Red. of Area min. % 50 50 50 50 50 50 50 50 50

Hardness max. HB 321 235 321 223 223 223 223

B7 B7M B16 B8 CL2 - B8T CL2 - B8C CL2

Diameterover 2 1/2"

to 4over 2 1/2"

to 4over 2 1/2"

to 43/4"

and underover 3/4"

to 1"over 1"

to 1 1/4"over 1 1/4"to 1 1/2"

T.S.min. Mpa 795 690 760 860 795 725 690

Y.S min. 0.2% Mpa 655 550 655 690 550 450 345

Elongation min.% 16 18 17 12 15 20 28

Red. of Area min. % 50 50 45 35 35 35 45

Hardness max. HB 321 235 321 321 321 321 321

B7 B7M B16 B8M CL2

Diameterover 4" to 7"

over 4"to 7"

over 4"to 7"

3/4"and under

over 3/4" to 1"

over 1"to 1 1/4"

over 1 1/4"to 1 1/2"

T.S. min. Mpa 690 690 690 760 690 655 620

Y.S min. 0.2% Mpa 515 515 586 655 550 450 345

Elongation min.% 18 18 16 15 20 25 30

Red. of Area min. % 50 50 45 45 45 45 45

Hardness max. HB 321 235 321 321 321 321 321

Aceros aleados e inoxidables para servicios de alta presióny alta temperaturaAlloy steel and stainless steel bolting for high-temperature

ASTM A-193 / ASME SA-193

Page 5: Esparragos y Tornillos Catalogo Tecnico

4DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ASTM A-320 / ASME SA-320Aceros aleados e inoxidables para baja temperaturaAlloy steel bolting for low-temperature

ASTM A-307 / SA-307Aceros para tornillos y tuercas / Carbon steel bolts and nuts

ASTM A-320 / ASME SA-320Alloy steel bolting for low-temperature

ASTM A-307/SA-307Carbon steel bolts and nuts

FERRITIC STEEL AUSTENITIC STEEL CARBON STEELL7 L7M L43 B8 B8M B8T B8C GR.A GR.B GR.C

AISI 4140 4340 304 316 321 347

DIN 42CrMo440NiCr Mo6

X5CrNi18-8X5CrNiMo17-12-2

X6CrNiTi 18-10

X6CrNiNb 18-10

W.-Nr. 1.7225 1.6565 1.4301 1.4401 1.4541 1.4550

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTS

C % 0,38-0,48 0,38-0,43 0,08 max. 0,08 max. 0,08 max. 0,08 max. 0,29 max.

Mn % 0,75-1,00 0,60-0,85 2 max. 2 max. 2 max. 2 max. 0,90 max.

Si % 0,15-0,35 0,15-0,35 1 max. 1 max. 1 max. 1 max. 0,50 max.

P max.% 0,035 0,035 0,045 0,045 0,045 0,045 0,04 max.

S max.% 0,040 0,040 0,030 0,030 0,030 0,030 0,15 0,05

Cr % 0,80-1,10 0,70-0,90 18-20 16-18 17-19 17-19

Ni % 1,65-2,00 8-11 10-14 9-12 9-12

Mo % 0,15-0,25 0,20-0,30 2-3

TI % 5xC min.

Cb+Ta10 x C min. 1,10 max.

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTS

Diameter2 1/2"

and under2 1/2"

and under4"

and underClass 1: all Diameters All Diameters

T.S min. Mpa 860 690 860 515 515 515 515 415 415-690 400-500

Y.S min. 0.2% Mpa 725 550 725 205 205 205 205 248

Elongation min.% 16 18 16 30 30 30 30 18 18 23

Red. of Area min. % 50 50 50 50 50 50 50

Impact.Test Min. (J) Ind. (20) med. (27)

Temp. -101°C -73°C -101°C

Hardness max. HB 235 223 223 223 223 121-241 121-212

B8 CL2 - B8T CL2 - B8C CL2

Diameter3/4"

and underover 3/4"

to 1"over 1"

to 1 1/4"over 1 1/4" to 1 1/2"

T.S min. Mpa 860 795 725 690

Y.S min. 0.2% Mpa 690 550 450 345

Elongation min.% 12 15 20 28

Red. of Area min. % 35 35 35 45

Hardness max. HB 321 321 321 321

B8M CL2

Diameter3/4"

and underover 3/4"

to 1"over 1"

to 1 1/4"over 1 1/4" to 1 1/2"

T.S min. Mpa 760 690 655 620

Y.S min. 0.2% Mpa 655 550 450 345

Elongation min.% 15 20 25 30

Red. of Area min. % 45 45 45 45

Hardness max. HB 321 321 321 321

Page 6: Esparragos y Tornillos Catalogo Tecnico

5DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ASTM A-453 B-164 F-467 B-446 B-166 B-408 B-574 A-182 A-182 A-182

GR.660 400 K500 625 600 800H C276 F-44 F-51 F-55

AISI - - - - - - - - - -

UNS S66286 N04400 N05500 N06625 N06600 N08810 N10276 S31254 S31803 S32760

W.-Nr. 1.4980 2.4360 2.4375 2.4856 2.4816 1.4876 2.4602 1.4547 1.4462 -

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTS

C max. % 0,08 0,30 0,25 0,10 0,15 0,05-0,10 0,02 0,02 0,03 0,03

Mn max. % 2,00 2,00 1,5 0,50 1,00 1,50 1,00 1,00 2,00 1,00

Si max. % 1,00 0,50 0,5 0,50 0,50 1,00 0,08 0,80 1,00 1,00

P max.% 0,04 0,015 0,030 0,030 0,030 0,030

S max.% 0,03 0,024 0,01 0,015 0,015 0,015 0,030 0,010 0,020 0,010

Cr % 13,5-16,0 20,0-23,0 14,0-17,0 19,0-23,0 14,5-16,5 19,5-20,5 21,0-23,0 24,0-26,0

Ni % 24,0-27,0 63 Min. 63,0-70,0 58 Min. 72 Min. 30,0-35,0 Bal. 17,5-18,5 4,5-6,5 6,0-8,0

Mo % 1,0-1,5 8,0-10,0 15,0-17,0 6,0-6,5 2,5-3,5 3,0-4,0

V % 0,10-0,50 0,35

TI % 1,9-2,35 0,35-0,85 0,40 Max. 0,15-0,60

Al max.% 0,35 2,30-3,15 0,40 0,15-0,60

Fe max. % 2,50 2,0 5,0 6,0-10,0 39,5 Min. 4,0-7,0

Cu max. % Bal. Bal. 0,50 0,75 0,50-1,00

N % 0,18-0,22 0,08-0,20 0,20-0,30

Co max.% 1,0 2,50

Cb+Ta % 3,15-4,15

W % 3,0-4,5

B % ,001-,010

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTS

T.S.min. Mpa 895 480 900 827 550 450 690 650 620 750-895

Y.S min. 0,2% Mpa 585 170 590 413 240 170 283 300 450 550

Elongation min.% 15 35 20 30 30 30 40 35 25 25

Red. of Area min. % 18 50 45 45

Hardness HB 248-341 24-37 HRC

ALEACIONES ESPECIALES ASTMSPECIAL ALLOYS ASTM

Gr. 660: Stress Rupture Test: Temperature 650°C: stress min.385 Mpa, Time to rupture min. 100 h. elongation min. 5%

Page 7: Esparragos y Tornillos Catalogo Tecnico

6DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Grade 2H 2HM 3 4 6 6F 7 7M 8 8T 8M 8C

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTS

C % ≥ 0.40 ≥ 0.40 ≥ 0.10 0.40-0.50 ≤ 0.15 ≤ 0.15 0.37-0.49 0.37-0.49 ≤0.08 ≤0.08 ≤0.08 ≤0.08

Mn % ≤ 1 ≤ 1 ≤ 1 0.70-0.90 ≤ 1.00 ≤ 1.25 0.65-1.10 0.65-1.10 ≤ 2 ≤ 2 ≤ 2 ≤ 2

P max. % 0.04 0.04 0.04 0.035 0.04 0.06 0.035 0.035 0.045 0.045 0.045 0.045

S max. % 0.05 0.05 0.03 0.04 0.03 0.06 0.04 0.04 0.03 0.03 0.03 0.03

Si % ≤ 0.40 ≤ 0.40 ≤ 1 0.15-0.35 ≤ 1 ≤ 1 0.15-0.35 0.15-0.35 ≤ 1 ≤ 1 ≤ 1 ≤ 1

Ni % 8-11 9-12 10-14 9-12

Cr % 4-6 11.5-13.5 12-14 0.75-1.20 0.75-1.20 18-20 17-19 16-18 17-19

Mo % 0.40-0.65 0.20-0.30 0.15-0.25 0.15-0.25 2-3

Ti %5xC+N

min.0.7 max.

Se % ≥ 0.15

Cb + Ta % 10xC.min.

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTS

BrinellHardness

Limits

To 1 1/2” inc.

248-327159 248 248 228 228 248 159 126 126 126 126

Over 1 1/2”212-327

235 327 327 271 271 327 235 300 300 300 300

EQUIVALENCE

AISI 1040 1040 501 410 416 Se 4140 4140 304 321 316 347

UNS K04002 K04002 550100 K14510 S41000 S41623 G41400 S 30400 S 32100 G 41400 S 31600 S34700

DIN C45 C4512CrMo

19-5X10Cr13 42CrMo4 42CrMo4

X5CrNi 18.8

X10CrNi Ti 18.10

X5CrNi Mo

17-12-2

X6CrNi Nb

18.10

W-NR 1.1191 1.1191 1.7362 1.4006 1.7225 1.7225 1.4301 1.4541 1.4401 1.4550

Aceros para tuercas / Carbon and Alloy Steel NutsASTM A-194 / ASME SA 194

Page 8: Esparragos y Tornillos Catalogo Tecnico

7DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ScrewScrew fastening material

(generic)Material

ASTM Specifications (1)

Screw Nuts

B5 5 Cr 501 A 193 Gr. B5 A 194 Gr. 3

B6 12 Cr 410 A 193 Gr. B6 A 194 Gr. 6

B7, B7M Cr-Mo 4140, 4142 or 4145 A 193 Gr. B7, B7M A 194 Gr. 2H, 2HM

B8 (3) 18 Cr - 8 Ni 304 A 193 Gr. B8, CI. 1 or CI. 2 A 194 Gr. 8

B8T 18 Cr-10 Ni-Ti 321 A 193 B8T A 194 Gr. 8

B8M 18 Cr-10 Ni-2 Mo 316 A320 Gr. B8M CI. 1 A 194 Gr. 8M

B16 Cr MoV A 193 Gr. B16 A 194 Gr. 4 or 7

A-307 Carbon steel A 307 Gr. B A 194 Gr. 2H

A-325 Carbon steel A 325 (4) A 325 (4)

L7 Cr-Mo 4140, 4142, 4145 A 320 Gr. L7 A 194 Gr. 4 or 7

310 25 Cr-20 Ni A 276, type 310 A 276, type 310

De aceros al carbono, aleados e inoxidables / Of carbon steels, steel alloys, and stainless steels

SELECCIÓN DE MATERIALES DE TORNILLERÍA

(1) The ASME specifications are preceded by SA instead of A, and have the same numeric designation (SA 193).

(2) Screws will only be marked with the specifications applicable to the material.

(3) Both classes, class 1, treated, and class 2, treated and hardened, can be used.

(4) Available with resistance to atmospheric corrosion and wear properties, type 3A.

(5) This table is for information purposes only, and the final decision as to the materials is to be provided by the client.

SELECTION OF RECOMMENDED MATERIALS FOR SCREW FASTENINGS(5)

Page 9: Esparragos y Tornillos Catalogo Tecnico

8DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. acc/ DIN 17240

ACEROS PARA SERVICIO DE ALTA TEMPERATURASTEEL FOR HIGH TEMPERATURE SERVICES

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTSMATERIAL

C Sl MnP

max.S

max.Al B Cr Mo Nl Tl V

Denomination w.-Nr

C35 1.05010.32 0.15 0.50

0.045 0.0450.39 0.35 0.80

CK35 1.11810.32 0.15 0.50

0.035 0.0350.39 0.35 0.80

24CrMo5 1.72580.20 0.15 0.50

0.030 0.0350.90 0.20

0.28 0.35 0.80 1.20 0.35

21CrMoV57 1.77090.17 0.15 0.35

0.030 0.0351.20 0.65 0.25

0.25 0.35 0.85 1.50 0.80 0.35

40CrMoV47 1.77110.36 0.15 0.35

0.030 0.0350.90 0.60 0.25

0.44 0.35 0.85 1.20 0.75 0.35

X22CrM0V121 1.49230.18 0.10

0.035 0.03511.0 0.80 0.30 0.25

0.24 0.50 0.80 12.5 1.20 0.80 0.35

X19CrMoVNbN11(1)

1.49130.16 0.10 0.30

0.035 0.035 ≤ 0.01010.0 0.50 0.30 0.10

0.22 0.50 0.80 11.5 1.00 0.80 0.30

X8CrNiMoBNb16.16(2)

1.49860.040 0.30

≤ 1.50 0.045 0.0300.05 15.5 1.60 15.5

0.10 0.60 0.10 17.5 2.00 17.5

NiCr20TiAl(3)

2.4952 ≤ 0.10 ≤ 1.00 ≤ 1.00 0.030 0.0151.00

≤ 0.00818.0

≥ 651.8

1.80 21.0 2.7

21CrMoV57 y 40CrMoV47 can be replaced by 24CrMoV55.(1) Also must contain: Nb 0,15-0,50; N 0.05-0.10.(2) Nb + Ta 10 x C.(3) Co ≤ 2.00; Fe ≤ 3.00.

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTSMATERIAL

StatusNominal

size

MECHANICAL REQUIREMENTSService

tempera-ture º C

Y.S min. 0,2% Mpa

T.S.min. Mpa

Elon-gation min.%

Red. of Area min.

%

D V M J. min.

Iso. V. J. min.Denomination w.-Nr

C35 1.0501N V

≤ 100 ≤160

280 280

500-650 500-650

21 22

40350 400

CK35 1.1181 V≤ 60

60 ≤160280 280

500-650 500-650

22 22

45 45

55 41

55 39

350 400

24CrMo5 1.7258V V

≤ 100 ≤160

440 420

600-750 600-750

18 18

60 60

103 89

118 102

400 400

21CrMoV57 40CrMoV47

1.7709 1.7711

V V

≤ 250 ≤ 100

550 700

700-850 850-1000

16 14

60 45

69 41

63 47

540 540

X22CrMoV121 1.4923 V ≤ 250600 700

800-950 900-1050

14 11

40 35

34 27

27 20

580 580

X19CrMoVNbN11 1.4913 V ≤ 250 780 900-1050 10 40 24 20 580

X8CrNiMoBNb16.16 1.4986 WK + AL ≤ 100 500 650-850 16 40 48 17 650

NiCr20TiAl 2.4952 AH ≤ 60 600 1000 12 12 17 20 700

N: normaliced; V: Quenched and tempered;Wk + AL: Hot-Rolled and age hardened;

AH: Precipitacion hardened.

Page 10: Esparragos y Tornillos Catalogo Tecnico

9DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 1/2” 12 2 1/2” 64

3/4” 4 1/2” 12 2 1/2” 64

1” 4 1/2” 12 2 3/4” 70 3 1/4” 83

1 1/4” 4 1/2” 12 23/4” 70 3 1/4” 83

1 1/2” 4 1/2” 12 3” 77 3 1/2” 89

2” 4 5/8” 16 3 1/4” 83 3 3/4” 96

2 1/2” 4 5/8” 16 3 1/2” 89 4” 102

3” 4 5/8” 16 3 3/4” 96 4 1/4” 96

3 1/2” 8 5/8” 16 3 3/4” 96 4 1/4” 108

4” 8 5/8” 16 3 3/4” 96 4 1/4” 108

5” 8 3/4” 20 4” 102 4 1/2” 115

6” 8 3/4” 20 4” 102 4 1/2” 115

8” 8 3/4” 20 4 1/4” 108 4 3/4” 121

10” 12 7/8” 24 4 3/4” 121 5 1/4” 134

12” 12 7/8” 24 4 3/4” 121 5 1/4” 134

14” 12 1” 27 5 1/4” 134 5 3/4” 146

16” 16 1” 27 5 1/2” 140 6” 153

18” 16 1 1/8” 30 6” 153 6 1/2” 166

20” 20 1 1/8” 30 6 1/4” 159 6 3/4” 172

24” 20 1 1/4” 33 7” 178 7 1/2” 191

26” 24 1 1/4” 33 8 1/2” 216

28” 28 1 1/4” 33 8 3/4” 223

30” 28 1 1/4” 33 9” 229

32” 28 1 1/2” 39 10” 254

34” 32 11/2” 39 10 1/4” 261

36” 32 1 1/2” 39 10 3/4” 274

38” 32 1 1/2” 39 10 1/2” 267

40” 36 1 1/2” 39 10 3/4” 274

42” 36 1 1/2” 39 11 1/4” 286

44” 40 1 1/2” 39 11 3/4” 299

46” 40 1 1/2” 39 11 3/4” 299

48” 44 1 1/2” 39 12 1/4” 312

50” 44 1 3/4” 45 13” 331

52” 44 1 3/4” 45 13 1/2” 343

54” 44 1 3/4” 45 13 3/4” 350

56” 48 1 3/4” 45 14” 356

58” 48 1 3/4” 45 14 1/2” 369

60” 52 1 3/4” 45 14 3/4” 375

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 150 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 11: Esparragos y Tornillos Catalogo Tecnico

10DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 1/2” 12 2 3/4” 70 3” 77

3/4” 4 5/8” 16 3” 77 3 1/2” 89

1” 4 5/8” 16 3 1/4” 83 3 3/4” 96

1 1/4” 4 5/8” 16 3 1/4” 83 3 3/4” 96

1 1/2” 4 3/4” 20 3 3/4” 96 4 1/4” 108

2” 8 5/8” 16 3 1/2” 89 4 1/4” 108

2 1/2” 8 3/4” 20 4” 102 4 3/4” 121

3” 8 3/4” 20 4 1/4” 108 5” 127

3 1/2” 8 3/4” 20 4 1/2” 115 5 1/4” 134

4” 8 3/4” 20 4 1/2” 115 5 1/4” 134

5” 8 3/4” 20 4 3/4” 121 5 1/2” 140

6” 12 3/4” 20 5” 127 5 3/4” 147

8” 12 7/8” 24 5 1/2” 140 6 1/4” 159

10” 16 1” 27 6 1/4” 159 7” 178

12” 16 1 1/8” 30 6 3/4” 172 7 1/2” 191

14” 20 1 1/8” 30 7” 178 7 3/4” 197

16” 20 1 1/4” 33 7 1/2” 191 8 1/4” 210

18” 24 1 1/4” 33 7 3/4” 197 8 1/2” 216

20” 24 1 1/4” 33 8 1/4” 210 9” 229

24” 24 1 1/2” 39 9 1/4” 234 10 1/4” 261

26” 28 1 5/8” 42 10 1/2” 267 11 1/2” 293

28” 28 1 5/8” 42 11” 280 11 1/2” 293

30” 28 1 3/4” 45 11 1/2” 293 12 3/4” 324

32” 28 1 7/8” 48 12 1/4” 312 13 1/2” 343

34” 28 1 7/8” 48 12 3/4” 324 14” 356

36” 32 2” 51 13 1/4” 337 14 1/2” 369

38” 32 1 1/2” 39 12 1/4” 312

40” 32 1 5/8” 42 13” 331

42” 32 1 5/8” 42 13 1/2” 343

44” 32 1 3/4” 45 14” 356

46” 28 1 7/8” 48 14 3/4” 375

48” 32 1 7/8” 48 15” 381

50” 32 2” 51 15 3/4” 401

52” 32 2” 51 16 1/4” 413

54” 28 2 1/4” 57 17 1/4” 439

56” 28 2 1/4” 57 17 1/2” 445

58” 32 2 1/4” 57 17 3/4” 451

60” 32 2 1/4” 57 18 1/4” 464

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 300 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 12: Esparragos y Tornillos Catalogo Tecnico

11DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 1/2” 12 3 1/4” 83 3” 83

3/4” 4 5/8” 16 3 1/2” 89 3 1/2” 89

1” 4 5/8” 16 3 3/4” 96 3 3/4” 96

1 1/4” 4 5/8” 16 4” 102 4” 102

1 1/2” 4 3/4” 20 4 1/4” 108 4 1/4” 108

2” 8 5/8” 16 4 1/4” 108 4 1/2” 115

2 1/2” 8 3/4” 20 4 3/4” 121 5” 127

3” 8 3/4” 20 5” 127 5 1/4” 134

3 1/2” 8 7/8” 24 5 1/2” 140 5 3/4” 147

4” 8 7/8” 24 5 1/2” 140 5 3/4” 147

5” 8 7/8” 24 5 3/4” 147 6” 153

6” 12 7/8” 24 6” 153 6 1/4” 159

8” 12 1” 27 6 3/4” 172 7” 178

10” 16 1 1/8” 30 7 1/2” 191 7 3/4” 196

12” 16 1 1/4” 33 8” 204 8 1/4” 210

14” 20 1 1/4” 33 8 1/4” 210 8 1/2” 216

16” 20 1 3/8” 36 8 3/4” 223 9” 229

18” 24 1 3/8” 36 9” 229 9 1/4” 235

20” 24 1 1/2” 39 9 3/4” 248 10” 254

24” 24 1 3/4” 45 10 3/4” 274 111/4” 286

26” 28 1 3/4” 45 12” 305 12 3/4” 324

28” 28 1 7/8” 48 13” 331 13 1/2” 343

30” 28 2” 51 13 3/4” 350 14 1/4” 362

32” 28 2” 51 14” 356 14 3/4” 375

34” 28 2” 51 14 1/2” 369 15 1/4” 388

36” 32 2” 51 14 3/4” 375 15 1/2” 394

38” 32 1 3/4” 45 14 1/2” 369

40” 32 1 7/8” 48 15 1/4” 388

42” 32 1 7/8” 48 15 1/2” 394

44” 32 2” 51 16 1/4” 413

46” 36 2” 51 16 3/4” 426

48” 28 2 1/4” 57 17 3/4” 451

50” 32 2 1/4” 57 18 1/4” 464

52” 32 2 1/4” 57 18 3/4” 477

54” 28 2 1/2” 63 19 3/4” 502

56” 32 2 1/2” 63 20 1/4” 515

58” 32 2 1/2” 63 20 1/2” 521

60” 32 2 3/4” 69 21 3/4” 553

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 400 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 13: Esparragos y Tornillos Catalogo Tecnico

12DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 1/2” 12 3 1/4” 83 3” 83

3/4” 4 5/8” 16 3 1/2” 89 3 1/2” 89

1” 4 5/8” 16 3 3/4” 96 3 3/4” 96

1 1/4” 4 5/8” 16 4” 102 4” 102

1 1/2” 4 3/4” 20 4 1/4” 108 4 1/4” 108

2” 8 5/8” 16 4 1/4” 108 4 1/2” 115

2 1/2” 8 3/4” 20 4 3/4” 121 5” 127

3” 8 3/4” 20 5” 127 5 1/4” 134

31/2” 8 7/8” 24 5 1/2” 140 5 3/4” 147

4” 8 7/8” 24 5 3/4” 147 6” 153

5” 8 1” 27 6 1/2” 166 6 3/4” 172

6” 12 1” 27 6 3/4” 172 7” 178

8” 12 1 1/8” 30 7 3/4” 197 7 3/4” 197

10” 16 1 1/4 33 8 1/2” 210 8 3/4” 223

12” 20 1 1/4” 33 8 3/4” 223 9” 229

14” 20 1 3/8” 36 9 1/4” 235 9 1/2” 242

16” 20 1 1/2” 39 10” 254 10 1//4” 261

18” 20 1 5/8” 42 10 3/4” 274 11” 280

20” 24 1 5/8” 42 11 1/2” 293 113/4” 299

24” 24 1 7/8” 48 13” 331 13 1/4” 337

26” 28 1 7/8” 48 14 1/4” 362 13 3/4” 375

28” 28 2” 51 14 3/4” 375 15 1/2” 394

30” 28 2” 51 15 1/4” 388 15 3/4” 401

32” 28 2 1/4” 57 16 1/4” 413 17” 432

34” 28 2 1/4” 57 16 1/2” 420 17 1/4” 439

36” 28 2 1/2” 63 17 1/2” 445 18 1/2” 470

38” 28 2 1/4” 57 18” 458

40” 32 2 1/4” 57 18 1/2” 470

42” 28 2 1/2” 63 19 3/4” 502

44” 32 2 1/2” 63 20 1/4” 515

46” 32 2 1/2 63 20 3/4” 528

48” 32 2 3/4” 69 22” 559

50” 28 3” 75 23 1/4” 591

52” 32 3” 75 34 3/4” 604

54” 32 3” 75 24 1/4” 616

56” 31 3 1/4” 81 25 1/4” 642

58” 32 3 1/4” 81 25 3/4” 655

60” 28 3 1/2” 87 27 1/4” 693

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 600 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 14: Esparragos y Tornillos Catalogo Tecnico

13DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 3/4” 20 4 1/4” 102 4 1/4” 108

3/4” 4 3/4” 20 4 1/2” 115 4 1/2” 115

1” 4 7/8” 24 5” 127 5” 127

1 1/4” 4 7/8” 24 5” 127 5” 127

1 1/2” 4 1” 27 5 1/2” 140 5 1/2” 140

2” 8 7/8” 24 5 3/4” 147 5 3/4” 147

2 1/2” 8 1” 27 6 1/4” 159 6 1/4” 159

3” 8 7/8” 24 5 3/4” 147 6” 153

4” 8 1 1/8” 30 6 3/4” 172 7” 178

5” 8 1 1/4” 33 7 1/2” 191 7 3/4” 197

6” 12 1 1/8” 30 7 3/4” 197 7 3/4” 197

8” 12 1 3/8” 36 8 3/4” 223 9” 229

10” 16 1 3/8” 36 9 1/4” 235 9 1/2” 242

12” 20 1 3/8” 36 10” 254 10 1/4” 261

14” 20 1 1/2” 39 10 3/4” 274 11 1/4” 286

16” 20 1 5/8” 42 11 1/2” 293 11 3/4” 299

18” 20 1 7/8” 48 12 3/4” 324 13 1/2” 343

20” 20 2” 51 13 1/2” 343 14 1/2” 362

24” 20 2 1/2” 63 17 1/4” 439 17 3/4” 451

26” 20 2 3/4” 69 18 3/4” 477 19 3/4” 502

28” 20 3” 75 19 3/4” 502 21” 534

30” 20 3” 75 20 1/2” 521 21 3/4” 553

32” 20 3 1/4” 81 21 3/4” 553 23” 585

34” 20 3 1/2” 87 23” 585 24 1/2” 623

36” 20 3 1/2” 87 23 1/2” 597 25” 635

38” 20 3 1/2” 87 24 1/2” 623

40” 24 3 1/2” 87 25” 635

42” 24 3 1/2” 87 25 3/4” 655

44” 24 3 3/4” 93 27” 686

46” 24 4” 99 28 1/4” 718

48” 24 4” 99 29” 737

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 900 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 15: Esparragos y Tornillos Catalogo Tecnico

14DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Ratingnominal size

QuantitySize

Length Studbolts

RF RJ

inches mm inches mm inches mm

1/2” 4 3/4” 20 4 1/4” 108 4 1/4” 108

3/4” 4 3/4” 20 4 1/2” 115 4 1/2” 115

1” 4 7/8” 24 5” 127 5”. 127

1 1/4” 4 7/8” 24 5” 127 5” 127

1 1/2” 4 1” 27 5 1/2” 140 5 1/2” 140

2” 8 7/8” 24 5 3/4” 147 5 3/4” 147

2 1/2” 8 1” 27 6 1/4” 159 6 1/4” 159

3” 8 1 1/8” 30 7” 178 7” 178

4” 8 1 1/4” 33 7 3/4” 197 7 3/4” 197

5” 8 1 1/2” 39 9 3/4” 248 9 3/4” 248

6” 12 1 3/8” 36 10 1/4” 261 10 1/2” 267

8” 12 1 5/8” 42 111/2” 293 12” 305

10” 12 1 7/8” 48 13 1/4” 337 13 3/4” 350

12” 16 2” 51 14 3/4” 375 15 1/2” 394

14” 16 2 1/4” 57 16” 407 17” 432

16” 16 2 1/2” 63 17 1/2” 445 18 1/2” 470

18” 16 2 3/4” 69 19 1/2” 496 20 1/2” 521

20” 16 3” 75 21 1/2” 547 22 1/2” 572

24” 16 3 1/2” 87 24 1/2” 623 25 3/4” 648

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 1500 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 16: Esparragos y Tornillos Catalogo Tecnico

15DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Rating nominal

sizeQuantity

SizeLength studbolts

RF RJ

inches mm. inches mm inches mm

1/2” 4 3/4” 20 5 1/4” 134 5 1/4” 134

3/4” 4 3/4” 20 5 1/4” 134 5 1/4” 134

1” 4 7/8” 24 5 3/4” 147 5 3/4” 147

1 1/4” 4 1” 27 6 1/4” 159 6 1/2” 166

1 1/2” 4 1 1/8” 30 7” 178 7 1/4” 185

2” 8 1” 27 7 1/4” 185 7 1/2” 191

2 1/2” 8 1 1/8” 30 8” 204 8 1/4” 210

3” 8 1 1/4” 33 9” 229 9 1/2” 235

4” 8 1 1/2” 39 10 1/4” 261 10 3/4” 274

5” 8 1 3/4” 45 12” 305 12 3/4” 324

6” 8 2” 54 13 3/4” 350 14 1/2” 369

8” 12 2” 54 15 1/4” 388 16” 407

10” 12 2 1/2” 63 19 1/2” 496 20 1/2” 521

12” 12 2 3/4” 69 21 1/2” 547 22 1/2” 572

ACC / ANSI B16.5

DIMENSIONES DE ESPÁRRAGOS PARA BRIDAS 2500 LBSSTUDBOLTS DIMENSIONS FOR FLANGES

Page 17: Esparragos y Tornillos Catalogo Tecnico

16DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Flange D. N.

CLASS PN-6 CLASS PN-10 CLASS PN-16 CLASS PN-25 CLASS PN-40

Size Nº Size Nº Size Nº Size Nº Size Nº

10 M 10 X 40 4 M 12 X 45 4 M 12 X 45 4 M 12 X 50 4 M 10 X 50 4

15 M 10 X 40 4 M 12 X 45 4 M 12 X 45 4 M 12 X 50 4 M 12 X 50 4

20 M 10 X 45 4 M 12 X 50 4 M 12 X 50 4 M 12 X 55 4 M 12 X 55 4

25 M 10 X 45 4 M 12 X 50 4 M 12 X 50 4 M 12 X 55 4 M 12 X 55 4

32 M 12 X 50 4 M 16 X 55 4 M 16 X 55 4 M 16 X 55 4 M 16 X 55 4

40 M 12 X 50 4 M 16 X 55 4 M 16 X 55 4 M 16 X 55 4 M 16 X 55 4

50 M 12 X 50 4 M 16 X 55 4 M 16 X 55 4 M 16 X 60 4 M 16 X 60 4

65 M 12 X 50 4 M 16 X 55 4 M 16 X 55 4 M 16 X 65 8 M 16 X 65 8

80 M 16 X 60 4 M 16 X 60 4 M 16 X 60 8 M 16 X 70 8 M 16 X 70 8

100 M 16 X 60 4 M 16 X 60 8 M 16 X 60 8 M 20 X 70 8 M 20 X 70 8

125 M 16 X 60 8 M 16 X 65 8 M 16 X 65 8 M 24 X 80 8 M 24 X 80 8

150 M 16 X 60 8 M 20 X 70 8 M 20 X 70 8 M 24 X 90 8 M 24 X 90 8

200 M 16 X 65 8 M 20 X 70 8 M 20 X 80 12 M 24 X 90 12 M 27 X 100 12

250 M 16 X 70 12 M 20 X 80 12 M 24 X 90 12 M 27 X 100 12 M 30 X 110 12

300 M 20 X 70 12 M 20 X 80 12 M 24 X 90 12 M 27 X 100 16 M 30 X 120 16

350 M 20 X 80 12 M 20 X 80 16 M 24 X 100 16 M 30 X 110 16 M 33 X 130 16

400 M 20 X 80 16 M 24 X 90 16 M 27 X 110 16 M 33 X 120 16 M 36 X 140 16

500 M 20 X 90 20 M 24 X 110 20 M 30 X 110 20 M 33 X 130 20 M 39 X 150 20

Para bridas DIN según / DIN 931/934 / For flanges DIN ACC / DIN 931/934

DIMENSIONES DE TORNILLO EXAGONAL C/TUERCAHEXAGONAL BOLT WITH NUT

Page 18: Esparragos y Tornillos Catalogo Tecnico

17DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. ACC/B16.5 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

3/8” 7/16” 1/2” 9/16” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.3/8” 1.1/2” 1.5/8” 1.3/4”

50 2” 0.024 0.032 0.044 0.055 0.070 0.103 0.141 0.185 0.238 0.299 0.366 0.441 0.521 0.611

55 2.1/4” 0.026 0.035 0.048 0.060 0.076 0.112 0.154 0.202 0.260 0.326 0.399 0.481 0.569 0.666

60 2.3/8” 0.028 0.038 0.052 0.065 0.083 0.122 0.166 0.218 0.281 0.353 0.432 0.521 0.616 0.722

65 2.1/2” 0.030 0.041 0.056 0.070 0.089 0.131 0.179 0.235 0.303 0.380 0.466 0.561 0.664 0.777

70 2.3/4” 0.032 0.044 0.060 0.075 0.095 0.140 0.192 0.252 0.325 0.407 0.499 0.601 0.711 0.833

75 3” 0.034 0.047 0.064 0.08 0.102 0.150 0.205 0.269 0.346 0.434 0.532 0.641 0.758 0.888

80 3.1/8” 0.037 0.050 0.068 0.085 0.108 0.159 0.218 0.286 0.368 0.462 0.565 0.681 0.806 0.944

85 3.1/4” 0.039 0.053 0.072 0.09 0.114 0.168 0.230 0.302 0.390 0.489 0.599 0.721 0.853 0.999

90 3.1/2” 0.041 0.056 0.076 0.095 0.121 0.178 0.243 0.319 0.411 0.516 0.632 0.761 0.901 1.055

95 3.3/4” 0.043 0.059 0.081 0.100 0.127 0.187 0.256 0.336 0.433 0.543 0.665 0.801 0.948 1.110

100 4” 0.045 0.061 0.085 0.105 0.133 0.196 0.269 0.353 0.455 0.570 0.698 0.841 0.995 1.166

105 4.1/8” 0.047 0.064 0.089 0.110 0.140 0.206 0.282 0.370 0.476 0.597 0.732 0.881 1.043 1.221

110 4.1/4” 0.050 0.067 0.093 0.115 0.146 0.215 0.294 0.386 0.498 0.624 0.765 0.921 1.090 1.277

115 4.1/2” 0.052 0.070 0.097 0.120 0.152 0.224 0.307 0.403 0.520 0.652 0.798 0.961 1.138 1.332

120 4.3/4” 0.054 0.073 0.101 0.125 0.159 0.234 0.320 0.420 0.541 0.679 0.831 1.001 1.185 1.388

125 5” 0.056 0.076 0.105 0.130 0.165 0.243 0.333 0.437 0.563 0.706 0.865 1.041 1.232 1.443

130 5.1/8” 0.058 0.079 0.109 0.135 0.171 0.252 0.346 0.454 0.585 0.733 0.898 1.081 1.280 1.499

135 5.1/4” 0.060 0.082 0.113 0.140 0.178 0.262 0.358 0.470 0.606 0.760 0.931 1.121 1.327 1.554

140 5.1/2” 0.062 0.085 0.117 0.145 0.184 0.271 0.371 0.487 0.628 0.787 0.964 1.161 1.375 1.610

145 5.3/4” 0.065 0.088 0.121 0.150 0.191 0.281 0.384 0.504 0.650 0.815 0.998 1.202 1.422 1.665

150 6” 0.067 0.091 0.125 0.155 0.197 0.290 0.397 0.521 0.671 0.842 1.031 1.242 1.469 1.721

155 6.1/8” 0.069 0.094 0.129 0.159 0.203 0.299 0.410 0.538 0.693 0.869 1.064 1.282 1.517 1.776

160 6.1/4” 0.071 0.097 0.133 0.164 0.210 0.309 0.422 0.554 0.714 0.896 1.097 1.322 1.564 1.832

165 6.1/2” 0.073 0.100 0.137 0.169 0.216 0.318 0.435 0.571 0.736 0.923 1.131 1.362 1.612 1.887

170 6.3/4” 0.075 0.102 0.141 0.174 0.222 0.327 0.448 0.588 0.758 0.950 1.164 1.402 1.659 1.943

175 6.7/8” 0.078 0.105 0.145 0.179 0.229 0.337 0.461 0.605 0.779 0.977 1.197 1.442 1.706 1.998

180 7” 0.080 0.108 0.149 0.184 0.235 0.346 0.474 0.622 0.801 1.005 1.230 1.482 1.754 2.054

185 7.1/4” 0.082 0.111 0.153 0.189 0.241 0.355 0.486 0.638 0.823 1.032 1.264 1.522 1.801 2.109

190 7.1/2” 0.084 0.114 0.157 0.194 0.248 0.365 0.499 0.655 0.844 1.059 1.297 1.562 1.896 2.165

195 7.3/4” 0.086 0.117 0.161 0.199 0.254 0.374 0.512 0.672 0.866 1.086 1.330 1.602 1.943 2.220

200 7.7/8” 0.088 0.120 0.165 0.204 0.260 0.383 0.525 0.689 0.888 1.113 1.363 1.642 1.991 2.276

205 8” 0.091 0.123 0.169 0.209 0.267 0.393 0.538 0.706 0.909 1.140 1.397 1.682 1.991 2.331

210 8.1/4” 0.093 0.126 0.173 0.214 0.273 0.402 0.550 0.722 0.931 1.167 1.430 1.722 2.038 2.387

215 8.1/2” 0.095 0.129 0.177 0.219 0.279 0.411 0.563 0.739 0.953 1.195 1.463 1.762 2.086 2.442

220 8.3/4” 0.097 0.132 0.181 0.224 0.286 0.421 0.576 0.756 0.974 1.222 1.496 1.802 2.133 2.498

225 8.7/8” 0.099 0.135 0.185 0.229 0.292 0.430 0.589 0.773 0.996 1.249 1.530 1.842 2.180 2.553

230 9” 0.101 0.138 0.189 0.234 0.298 0.439 0.602 0.790 1.018 1.276 1.563 1.882 2.228 2.609

235 9.1/4” 0.103 0.141 0.193 0.239 0.305 0.449 0.614 0.806 1.039 1.303 1.596 1.922 2.275 2.664

240 9.1/2” 0.106 0.143 0.197 0.244 0.311 0.458 0.627 0.823 1.061 1.330 1.629 1.962 2.323 2.720

245 9.5/8” 0.108 0.146 0.201 0.249 0.318 0.468 0.640 0.840 1.083 1.358 1.663 2.003 2.370 2.775

250 9.3/4” 0.110 0.149 0.205 0.254 0.324 0.477 0.653 0.357 1.104 1.385 1.696 2.043 2.417 2.831

255 10” 0.112 0.152 0.209 0.259 0.330 0.486 0.666 0.874 1.126 1.412 1.729 2.083 2.465 2.886

260 10.1/4” 0.114 0.155 0.213 0.264 0.337 0.496 0.678 0.890 1.147 1.439 1.762 2.123 2.512 2.942

265 10.1/2” 0.116 0.158 0.217 0.269 0.343 0.505 0.691 0.907 1.169 1.466 1.796 2.163 2.560 2.997

270 10.5/8” 0.119 0.161 0.221 0.274 0.349 0.514 0.704 0.924 1.191 1.493 1.829 2.203 2.607 3.053

275 10.3/4” 0.121 0.164 0.225 0.279 0.356 0.524 0.717 0.941 1.212 1.520 1.862 2.243 2.654 3.108

d

l

Page 19: Esparragos y Tornillos Catalogo Tecnico

18DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

3/8” 7/16” 1/2” 9/16” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.3/8” 1.1/2” 1.5/8” 1.3/4”

280 11” 0.123 0.167 0.229 0.284 0.362 0.533 0.730 0.958 1.234 1.548 1.895 2.283 2.702 3.164

285 11.1/4” 0.125 0.170 0.233 0.289 0.368 0.542 0.742 0.974 1.256 1.575 1.929 2.323 2.749 3.219

290 11.1/2” 0.127 0.173 0.237 0.294 0.375 0.552 0.755 0.991 1.277 1.602 1.962 2.363 2.797 3.275

295 11.5/8” 0.129 0.176 0.242 0.299 0.381 0.561 0.768 1.008 1.299 1.629 1.995 2.403 2.844 3.330

300 11.3/4” 0.131 0.179 0.246 0.304 0.387 0.570 0.781 1.025 1.321 1.656 2.028 2.443 2.891 3.386

305 12” 0.134 0.182 0.250 0.309 0.394 0.580 0.794 1.042 1.342 1.683 2.062 2.483 2.939 3.441

310 12.1/4” 0.136 0.184 0.254 0.314 0.400 0.589 0.806 1.058 1.364 1.710 2.095 2.523 2.986 3.497

315 12.1/2” 0.138 0.187 0.258 0.319 0.406 0.598 0.819 1.075 1.386 1.738 2.128 2.563 3.034 3.552

320 12.5/8” 0.140 0.190 0.262 0.324 0.413 0.608 0.832 1.092 1.407 1.765 2.161 2.603 3.081 3.608

325 12.3/4” 0.142 0.193 0.266 0.329 0.419 0.617 0.845 1.109 1.429 1.792 2.195 2.643 3.128 3.663

330 13” 0.144 0.196 0.270 0.334 0.425 0.626 0.858 1.126 1.451 1.819 2.228 2.683 3.176 3.719

335 13.1/4” 0.147 0.199 0.274 0.339 0.432 0.636 0.870 1.142 1.472 1.846 2.261 2.723 3.223 3.774

340 13.3/8” 0.149 0.202 0.278 0.344 0.438 0.645 0.883 1.159 1.494 1.873 2.294 2.763 3.271 3.830

345 13.1/2” 0.151 0.205 0.282 0.349 0.445 0.655 0.896 1.176 1.516 1.901 2.328 2.804 3.318 3.885

350 13.3/4” 0.153 0.208 0.286 0.354 0.451 0.664 0.909 1.193 1.537 1.928 2.361 2.844 3.365 3.941

355 14” 0.155 0.211 0.290 0.359 0.457 0.673 0.922 1.210 1.559 1.955 2.394 2.884 3.413 3.996

360 14.1/4” 0.157 0.214 0.294 0.364 0.464 0.683 0.934 1.226 1.580 1.982 2.427 2.924 3.460 4.052

365 14.3/8” 0.159 0.217 0.298 0.369 0.470 0.692 0.947 1.243 1.602 2.009 2.461 2.964 3.508 4.107

370 14.1/2” 0.162 0.220 0.302 0.374 0.476 0.701 0.960 1.260 1.624 2.036 2.494 3.004 3.555 4.163

375 14.3/4” 0.164 0.223 0.306 0.379 0.483 0.711 0.973 1.277 1.645 2.063 2.527 3.044 3.602 4.218

380 15” 0.166 0.225 0.310 0.384 0.489 0.720 0.986 1.294 1.667 2.091 2.560 3.084 3.650 4.274

385 15.1/4” 0.168 0.228 0.314 0.389 0.495 0.729 0.998 1.310 1.689 2.118 2.594 3.124 3.697 4.329

390 15.3/8” 0.170 0.231 0.318 0.394 0.502 0.739 1.011 1.327 1.710 2.145 2.627 3.164 3.745 4.385

395 15.1/2” 0.172 0.234 0.322 0.399 0.508 0.748 1.024 1.344 1.732 2.172 2.660 3.204 3.792 4.440

400 15.3/4” 0.175 0.237 0.326 0.404 0.514 0.757 1.037 1.361 1.754 2.199 2.693 3.244 3.839 4.496

405 16” 0.177 0.240 0.330 0.409 0.521 0.767 1.050 1.378 1.775 2.226 2.727 3.284 3.887 4.551

410 16.1/4” 0.179 0.243 0.334 0.414 0.527 0.776 1.062 1.394 1.797 2.253 2.760 3.324 3.934 4.607

415 16.3/8” 0.181 0.246 0.338 0.419 0.533 0.785 1.075 1.411 1.819 2.281 2.793 3.364 3.982 4.662

420 16.1/2” 0.183 0.249 0.342 0.424 0.540 0.795 1.088 1.428 1.840 2.308 2.826 3.404 4.029 4.718

425 16.3/4” 0.185 0.252 0.346 0.429 0.546 0.804 1.101 1.445 1.862 2.335 2.860 3.444 4.076 4.773

430 17” 0.187 0.255 0.35 0.434 0.552 0.813 1.114 1.462 1.884 2.362 2.893 3.484 4.124 4.829

435 17.1/8” 0.190 0.258 0.354 0.439 0.559 0.823 1.126 1.478 1.905 2389 2.926 3.524 4.171 4.884

440 17.1/4” 0.192 0.261 0.358 0.444 0.565 0.832 1.139 1.495 1.927 2.416 2.959 3.564 4.219 4.940

445 17.1/2” 0.194 0.264 0.362 0.449 0.572 0.842 1.152 1.512 1.949 2.444 2.993 3.605 4.266 4.995

450 17.3/4” 0.196 0.266 0.366 0.454 0.578 0.851 1.165 1.529 1.970 2.471 3.026 3.645 4.313 5.051

455 18” 0.198 0.269 0.370 0.459 0.584 0.860 1.178 1.545 1.992 2.498 3.059 3.685 4.361 5.106

460 18.1/8” 0.200 0.272 0.374 0.464 0.591 0.870 1.190 1.562 2.013 2.525 3.092 3.725 4.408 5.162

465 18.1/4” 0.203 0.275 0.378 0.468 0.597 0.879 1.203 1.579 2.035 2552 3.126 3.765 4.456 5.217

470 18.1/2” 0.205 0.278 0.382 0.473 0.603 0.888 1.216 1.596 2.057 2.579 3.159 3.805 4.503 5.273

475 18.3/4” 0.207 0.281 0.386 0.478 0.610 0.898 1.229 1.613 2.078 2.606 3.192 3.845 4.550 5.328

480 18.7/8” 0.209 0.284 0.39 0.483 0.616 0.907 1.242 1.630 2.100 2.634 3.225 3.885 4.598 5.384

485 19” 0.211 0.287 0.394 0.488 0.622 0.916 1.254 1.646 2.122 2.66! 3.259 3.925 4.645 5.439

490 19.1/4” 0.213 0.290 0.398 0.493 0.629 0.926 1.267 1.663 2.143 2.688 3.292 3.965 4.693 5.495

495 19.1/2” 0.216 0.293 0.403 0.498 0.635 0.935 1.280 1.680 2.165 2.715 3.325 4.005 4.740 5.550

500 19.3/4” 0.218 0.296 0.407 0.503 0.641 0.944 1.293 1.697 2.187 2.742 3.358 4.045 4.787 5.606

d

l

ACC/B16.5 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 20: Esparragos y Tornillos Catalogo Tecnico

19DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

1.7/8” 2” 2.1/4” 2.1/2” 2.3/4” 3” 3.1/4 3.1/2” 3.3/4” 4”50 2” 0.704 0.803 1.029 1.282 1.557 1.865 2.228 2.596 2.915 3.348

55 2.1/4” 0.768 0.876 1.122 1.398 1.698 2.034 2.430 2.832 3.180 3.653

60 2.3/8” 0.832 0.949 1.216 1.515 1.840 2.204 2.633 3.068 3.445 3.957

65 2.1/2” 0.896 1.022 1.309 1.631 1.981 2.373 2.835 3.304 3.710 4.262

70 2.3/4” 0.960 1.095 1.403 1.748 2.123 2.543 3.038 3.540 3.975 4.566

75 3” 1.024 1.168 1.496 1.864 2.264 2.712 3.240 3.776 4.240 4.870

80 3.1/8” 1.088 1.241 1.590 1.981 2.406 2.882 3.443 4.012 4.505 5.175

85 3.1/4” 1.152 1.314 1.683 2.097 2.547 3.051 3.645 4.248 4.770 5.479

90 3.1/2” 1.216 1.387 1.777 2.214 2.689 3.221 3.848 4.484 5.035 5.784

95 3.3/4” 1.280 1.460 1.870 2.330 2.830 3.390 4.050 4.720 5.300 6.088

100 4” 1.344 1.533 1.964 2.447 2.972 3.560 4.253 4.956 5.565 6.392

105 4.1/8” 1.408 1.606 2.057 2.563 3.113 3.729 4.455 5.192 5.830 6.697

110 4.1/4” 1.472 1.679 2.151 2.680 3.255 3.899 4.658 5.428 6.095 7.001

115 4.1/2” 1.536 1.752 2.244 2.796 3.396 4.068 4.860 5.664 6.360 7.306

120 4.3/4” 1.600 1.825 2.338 2.913 3.538 4.238 5.063 5.900 6.625 7.610

125 5” 1.664 1.898 2.431 3.029 3.679 4.407 5.265 6.136 6.890 7.914

130 5.1/8” 1.728 1.971 2.525 3.146 3.821 4.577 5.468 6.371 7.155 8.219

135 5.1/4” 1.792 2.044 2.618 3.262 3.962 4.746 5.670 6.608 7.420 8.523

140 5.1/2” 1.856 2.117 2.712 3.379 4.104 4.916 5.873 6.844 7.685 8.828

145 5.3/4” 1.920 2.190 2.805 3.495 4.245 5.085 6.075 7.080 7.950 9.132

150 6” 1.984 2.263 2.899 3.612 4.387 5.255 6.278 7.316 8.215 9.436

155 6.1/8” 2.048 2.336 2.992 3.728 4.528 5.424 6.480 7.552 8.480 9.741

160 6.1/4” 2.112 2.409 3.086 3.845 4.670 5.594 6.683 7.788 8.745 10.045

165 6.1/2” 2.176 2.482 3.179 3.961 4.811 5.763 6.885 8.024 9.010 10.350

170 6.3/4” 2.240 2.555 3.273 4.078 4.953 5.933 7.088 8.260 9.275 10.654

175 6.7/8” 2.304 2.628 3.366 4.194 5.094 6.102 7.290 8.496 9.540 10.958

180 7” 2.368 2.701 3.460 4.311 5.236 6.272 7.493 8.732 9.805 11.263

185 7.1/4” 2.432 2.774 3.553 4.427 5.377 6.441 7.695 8.968 10.070 11.567

190 7.1/2” 2.496 2.847 3.647 4.544 5.519 6.611 7.898 9.204 10.335 11.872

195 7.3/4” 2.560 2.920 3.740 4.660 5.660 6.780 8.100 9.440 10.600 12.176

200 7.7/8” 2.624 2.993 3.834 4.777 5.802 6.950 8.303 9.676 10.865 12.480

205 8” 2.688 3.066 3.927 4.893 5.943 7.119 8.505 9.912 11.130 12.785

210 8.1/4” 2.752 3.139 4.021 5.010 6.085 7.289 8.708 10.148 11.395 13.089

215 8.1/2” 2.816 3.212 4.114 5.126 6.226 7.458 8.910 10.384 11.660 13.394

220 8.3/4” 2.880 3.285 4.208 5.243 6.368 7.628 9.113 10.620 11.925 13.698

225 8.7/8” 2.944 3.358 4.301 5.359 6.509 7.797 9.315 10.856 12.190 14.002

230 9” 3.008 3.431 4.395 5.476 6.651 7.967 9.518 11.092 12.455 14.307

235 9.1/4” 3.072 3.504 4.488 5.592 6.792 8.136 9.720 11.328 12.720 14.611

240 9.1/2” 3.136 3.577 4.582 5.709 6.934 8.306 9.923 11.564 12.985 14.916

245 9.5/8” 3.200 3.650 4.675 5.825 7.075 8.475 10.125 11.800 13.250 15.220

250 9.3/4” 3.264 3.723 4.769 5.942 7.217 8.645 10.328 12.036 13.515 15.524

255 10” 3.328 3.796 4.862 6.058 7.358 8.814 10.530 12.272 13.780 15.829

260 10.1/4” 3.392 3.869 4.956 6.175 7.500 8.984 10.733 12.508 14.045 16.133

265 10.1/2” 3.456 3.942 5.049 6.291 7.641 9.153 10.935 12.744 14.310 16.438

270 10.5/8” 3.520 4.015 5.143 6.408 7.783 9.323 11.138 12.980 14.575 16.742

275 10.3/4” 3.584 4.088 5.236 6.524 7.924 9.492 11.340 13.216 14.840 17.046

d

l

ACC/B16.5 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 21: Esparragos y Tornillos Catalogo Tecnico

20DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

1.7/8” 2” 2.1/4” 2.1/2” 2.3/4” 3” 3.1/4 3.1/2” 3.3/4” 4”280 11” 3.648 4.161 5.330 6.641 8.066 9.662 11.543 13.452 15.105 17.351

285 11.1/4” 3.712 4.234 5.423 6.757 8.207 9.831 11.745 13.688 15.370 17.655

290 11.1/2” 3.776 4.307 5.517 6.874 8.349 10.001 11.948 13.924 15.635 17.960

295 11.5/8” 3.840 4.380 5.610 6.990 8.490 10.170 12.150 14.160 15.900 18.264

300 11.3/4” 3.904 4.453 5.704 7.107 8.632 10.340 12.353 14.396 16.165 18.568

305 12” 3.968 4.526 5.792 7.223 8.773 10.509 12.555 14.632 16.430 18.873

310 12.1/4” 4.032 4.599 5.891 7.340 8.915 10.679 12.758 14.868 16.695 19.177

315 12.1/2” 4.096 4.672 5.984 7.456 9.056 10.848 12.960 15.104 16.960 19.482

320 12.5/8” 4.160 4.745 6.078 7.573 9.198 11.018 13.163 15.340 17.225 19.786

325 12.3/4” 4.224 4.818 6.171 7.689 9.339 11.187 13.365 15.576 17.490 20.090

330 13” 4.288 4.891 6.265 7.806 9.481 11.357 13.568 15.812 17.755 20.395

335 13.1/4” 4.352 4.964 6.358 7.922 9.622 11.526 13.770 16.048 18.020 20.699

340 13.3/8” 4.416 5.037 6.452 8.039 9.764 11.696 13.973 16.284 18.285 21.004

345 13.1/2” 4.480 5.110 6.545 8.155 9.905 11.865 14.175 16.520 18.550 21.308

350 13.3/4” 4.544 5.183 6.639 8.272 10.047 12.035 14.378 16.756 18.815 21.612

355 14” 4.608 5.256 6.732 8.388 10.188 12.204 14.580 16.992 19.080 21.917

360 14.1/4” 4.622 5.329 6.826 8.505 10.330 12.374 14.783 17.228 19.345 22.221

365 14.3/8” 4.736 5.402 6.919 8.621 10.471 12.543 14.985 17.464 19.610 22.526

370 14.1/2” 4.800 5.475 7.013 8.738 10.613 12.713 15.188 17.700 19.875 22.830

375 14.3/4” 4.864 5.548 7.106 8.854 10.754 12.882 15.390 17.936 20.140 23.134

380 15” 4.928 5.621 7.200 8.971 10.896 13.052 15.593 18.172 20.405 23.439

385 15.1/4” 4.992 5.694 7.293 9.087 11.037 13.221 15.795 18.408 20.670 23.743

390 15.3/8” 5.056 5.767 7.387 9.204 11.179 13.391 15.998 18.644 20.935 24.048

395 15.1/2” 5.120 5.840 7480 9.320 11.320 13.560 16.200 18.880 21.200 24.352

400 15.3/4” 5.184 5.913 7.574 9.437 11.462 13.730 16.403 19.116 21.465 24.656

405 16” 5.248 5.986 7.667 9.553 11.603 13.899 16.605 19.352 21.730 24.961

410 16.1/4” 5.312 6.059 7.761 9.670 11.745 14.069 16.808 19.588 21.995 25.265

415 16.3/8” 5.376 6.132 7.854 9.786 11.886 14.238 17.010 19.824 22.260 25.570

420 16.1/2” 5.440 6.205 7.948 9.903 12.028 14.408 17.213 20.060 22.525 25.874

425 16.3/4” 5.504 6.278 8.041 10.019 12.169 14.577 17.415 20.296 22.790 26.178

430 17” 5.568 6.351 8.135 10.136 12.311 14.747 17.618 20.532 23.055 26.483

435 17.1/8” 5.632 6.424 8.228 10.252 12.452 14.916 17.820 20.768 23.320 26.787

440 17.1/4” 5.696 6.497 8.322 10.369 12.594 15.086 18.023 21.004 23.585 27.092

445 17.1/2” 5.760 6.570 8.415 10.485 12.735 15.255 18.225 21.240 23.850 27.396

450 17.3/4” 5.824 6.643 8.509 10.602 12.877 15.425 18.428 21.476 24.115 27.700

455 18” 5.888 6.716 8.602 10.718 13.018 15.594 18.630 21.712 24.380 28.005

460 18.1/8” 5.952 6.789 8.696 10.835 13.160 15.764 18.833 21.948 24.645 28.309

465 18.1/4” 6.016 6.861 8.789 10.951 13.301 15.933 19.035 22.184 24.910 28.614

470 18.1/2” 6.080 6.935 8.883 11.068 13.443 16.103 19.238 22.420 25.175 28.918

475 18.3/4” 6.144 7.008 8.976 11.184 13.584 16.272 19.440 22.656 25.440 29.222

480 18.7/8” 6.208 7.081 9.070 11.301 13.726 16.442 19.643 22.892 25.705 29.527

485 19” 6.272 7.154 9.163 11.417 13.867 16.611 19.845 23.128 25.970 29.831

490 19.1/4” 6.336 7.227 9.257 11.534 14.009 16.781 20.048 23.364 26.235 30.136

495 19.1/2” 6.400 7.300 9.350 11.650 14.150 16.950 20.250 23.600 26.500 30.440

500 19 3/4” 6.464 7.373 9.444 11.767 14.292 17.120 20.453 23.836 26.765 30.744

d

l

ACC/B16.5 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 22: Esparragos y Tornillos Catalogo Tecnico

21DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36 M3950 0.015 0.024 0.035 0.049 0.066 0.082 0.103 0.128 0.149 0.193 0.233 0.287 0.353 0.419

55 0.017 0.027 0.039 0.054 0.072 0.090 0.113 0.141 0.164 0.212 0.256 0.315 0.388 0.460

60 0.019 0.029 0.042 0.059 0.079 0.098 0.124 0.154 0.129 0.231 0.280 0.344 0.424 0.502

65 0.020 0.032 0.046 0.064 0.085 0.106 0.134 0.166 0.194 0.250 0.303 0.373 0.459 0.544

70 0.022 0.034 0.049 0.068 0.092 0.115 0.144 0.179 0.209 0.270 0.326 0.401 0.494 0.586

75 0.023 0.037 0.053 0.023 0.099 0.123 0.155 0.192 0.224 0.289 0.350 0.430 0.530 0.628

80 0.025 0.039 0.056 0.078 0.105 0.131 0.165 0.205 0.238 0.308 0.373 0.459 0.565 0.670

85 0.026 0.042 0.060 0.083 0.112 0.139 0.175 0.218 0.253 0.327 0.396 0.487 0.600 0.711

90 0.028 0.044 0.063 0.088 0.118 0.147 0.185 0.230 0.268 0.347 0.420 0.516 0.635 0.753

95 0.029 0.046 0.067 0.093 0.125 0.156 0.196 0.243 0.283 0.366 0.443 0.545 0.671 0.795

100 0.031 0.049 0.071 0.098 0.131 0.164 0.206 0.256 0.298 0.385 0.466 0.573 0.706 0.837

105 0.032 0.051 0.074 0.103 0.138 0.172 0.216 0.269 0.313 0.404 0.490 0.602 0.741 0.879

110 0.034 0.054 0.078 0.108 0.145 0.180 0.227 0.282 0.328 0.424 0.513 0.631 0.777 0.921

115 0.035 0.056 0.081 0.112 0.151 0.188 0.237 0.294 0.343 0.443 0.536 0.659 0.812 0.963

120 0.037 0.059 0.085 0.117 0.158 0.196 0.247 0.307 0.358 0.462 0.559 0.688 0.847 1.004

125 0.039 0.061 0.088 0.122 0.164 0.205 0.258 0.320 0.373 0.481 0.583 0.717 0.883 1.046

130 0.040 0.064 0.092 0.127 0.171 0.213 0.268 0.333 0.387 0.501 0.606 0.745 0.918 1.088

135 0.042 0.066 0.095 0.132 0.177 0.221 0.278 0.346 0.402 0.520 0.629 0.774 0.953 1.130

140 0.043 0.068 0.099 0.137 0.184 0.229 0.288 0.358 0.417 0.539 0.653 0.803 0.988 1.172

145 0.045 0.071 0.102 0.142 0.191 0.237 0.299 0.371 0.432 0.558 0.676 0.831 1.024 1.214

150 0.046 0.073 0.106 0.147 0.197 0.246 0.309 0.384 0.447 0.578 0.699 0.860 1.059 1.256

155 0.048 0.076 0.109 0.152 0.204 0.254 0.319 0.397 0.462 0.597 0.723 0.889 1.094 1.297

160 0.049 0.078 0.113 0.156 0.210 0.262 0.330 0.410 0.477 0.616 0.746 0.917 1.130 1.339

165 0.051 0.081 0.116 0.161 0.217 0.270 0.340 0.422 0.492 0.635 0.769 0.946 1.165 1.381

170 0.052 0.083 0.120 0.166 0.223 0.278 0.350 0.435 0.507 0.655 0.793 0.975 1.200 1.423

175 0.054 0.086 0.123 0.171 0.230 0.286 0.361 0.448 0.522 0.674 0.816 1.003 1.236 1.465

180 0.056 0.088 0.127 0.176 0.237 0.295 0.371 0.461 0.536 0.693 0.839 1.032 1.271 1.507

185 0.057 0.090 0.130 0.181 0.243 0.303 0.381 0.474 0.551 0.712 0.862 1.061 1.306 1.548

190 0.059 0.093 0.134 0.186 0.250 0.311 0.391 0.486 0.566 0.732 0.886 1.089 1.341 1.59

195 0.060 0.095 0.137 0.191 0.256 0.319 0.402 0.499 0.581 0.751 0.909 1.118 1.377 1.632

200 0.062 0.098 0.141 0.196 0.263 0.327 0.412 0.512 0.596 0.770 0.932 1.147 1.417 1.674

205 0.063 0.100 0.145 0.200 0.269 0.336 0.422 0.525 0.611 0.789 0.956 1.175 1.447 1.716

210 0.065 0.103 0.148 0.205 0.276 0.344 0.433 0.538 0.626 0.809 0.979 1.204 1.483 1.758

215 0.066 0.105 0.152 0.210 0.283 0.352 0.443 0.550 0.641 0.828 1.002 1.233 1.518 1.800

220 0.068 0.108 0.155 0.215 0.289 0.360 0.453 0.563 0.656 0.847 1.026 1.261 1.553 1.841

225 0.069 0.110 0.159 0.220 0.296 0.368 0.464 0.576 0.671 0.866 1.049 1.290 1.589 1.883

230 0.071 0.112 0.162 0.225 0.302 0.377 0.474 0.589 0.685 0.886 1.072 1.319 1.624 1.925

235 0.073 0.115 0.166 0.230 0.309 0.385 0.484 0.602 0.700 0.905 1.096 1.347 1.659 1.967

240 0.074 0.117 0.169 0.235 0.315 0.393 0.494 0.614 0.715 0.924 1.119 1.376 1.694 2.009

245 0.076 0.120 0.173 0.240 0.322 0.401 0.505 0.627 0.730 0.943 1.142 1.405 1.730 2.051

250 0.077 0.122 0.176 0.245 0.329 0.409 0.515 0.640 0.745 0.963 1.166 1.434 1.765 2.093

255 0.079 0.125 0.180 0.249 0.335 0.417 0.525 0.653 0.760 0.982 1.189 1.462 1.800 2.134

260 0.080 0.127 0.183 0.254 0.342 0.426 0.536 0.666 0.775 1.001 1.212 1.491 1.836 2.126

265 0.082 0.130 0.187 0.259 0.348 0.434 0.546 0.678 0.790 1.020 1.235 1.520 1.871 2.218

270 0.083 0.132 0.190 0.264 0.355 0.442 0.556 0.691 0.805 1.040 1.259 1.548 1.906 2.260

275 0.085 0.134 0.194 0.269 0.361 0.450 0.567 0.704 0.820 1.059 1.282 1.577 1.942 2.302

d

l

ACC/DIN 976 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 23: Esparragos y Tornillos Catalogo Tecnico

22DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

l d PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36 M39280 0.086 0.137 0.197 0.274 0.368 0.458 0.577 0.717 0.834 1.078 1.305 1.606 1.977 2.344

285 0.088 0.139 0.201 0.279 0.374 0.467 0.587 0.730 0.849 1.097 1.329 1.634 2.012 2.385

290 0.089 0.142 0.204 0.284 0.381 0.425 0.597 0.742 0.864 1.117 1.352 1.663 2.047 2.427

295 0.091 0.144 0.208 0.289 0.388 0.483 0.608 0.755 0.879 1.136 1.375 1.692 2.083 2.469

300 0.093 0.147 0.212 0.293 0.394 0.491 0.618 0.768 0.894 1.155 1.399 1.720 2.118 2.511

305 0.094 0.149 0.215 0.298 0.401 0.499 0.628 0.781 0.909 1.174 1.422 1.749 2.153 2.553

310 0.096 0.152 0.219 0.303 0.407 0.507 0.639 0.794 0.924 1.194 1.445 1.778 2.189 2.595

315 0.097 0.154 0.222 0.308 0.414 0.516 0.649 0.806 0.939 1.213 1.469 1.806 2.224 2.637

320 0.099 0.156 0.226 0.313 0.420 0.524 0.659 0.819 0.954 1.232 1.492 1.835 2.259 2.678

325 0.100 0.159 0.229 0.318 0.427 0.532 0.670 0.832 0.969 1.251 1.515 1.864 2.295 2.720

330 0.102 0.161 0.233 0.323 0.434 0.540 0.680 0.845 0.983 1.271 1.538 1.892 2.330 2.762

335 0.103 0.164 0.236 0.328 0.440 0.548 0.690 0.858 0.998 1.290 1.562 1.921 2.365 2.804

340 0.105 0.166 0.240 0.333 0.447 0.557 0.700 0.870 1.013 1.309 1.585 1.950 2.400 2.846

345 0.106 0.169 0.243 0.337 0.453 0.565 0.711 0.883 1.028 1.328 1.608 1.978 2.436 2.888

350 0.108 0.171 0.242 0.342 0.460 0.523 0.721 0.896 1.043 1.348 1.632 2.007 2.471 2.930

355 0.110 0.174 0.250 0.347 0.466 0.581 0.731 0.909 1.058 1.367 1.655 2.036 2.506 2.971

360 0.111 0.176 0.254 0.352 0.473 0.589 0.742 0.922 1.073 1.386 1.678 2.064 2.542 3.013

365 0.113 0.178 0.257 0.357 0.480 0.598 0.752 0.934 1.088 1.405 1.702 2.093 2.577 3.055

370 0.114 0.181 0.261 0.362 0.486 0.606 0.762 0.947 1.103 1.425 1.725 2.122 2.612 3.097

375 0.116 0.183 0.264 0.367 0.493 0.614 0.773 0.960 1.118 1.444 1.748 2.150 2.648 3.139

380 0.117 0.186 0.268 0.372 0.499 0.622 0.783 0.973 1.132 1.463 1.772 2.179 2.683 3.181

385 0.119 0.188 0.271 0.377 0.506 0.630 0.793 0.986 1.147 1.482 1.795 2.208 2.718 3.222

390 0.120 0.191 0.275 0.381 0.512 0.638 0.803 0.998 1.162 1.502 1.818 2.236 2.753 3.264

395 0.122 0.193 0.278 0.386 0.519 0.647 0.814 1.011 1.177 1.521 1.841 2.265 2.789 3.306

400 0.123 0.196 0.282 0.391 0.526 0.655 0.824 1.024 1.192 1.540 1.865 2.294 2.824 3.348

405 0.125 0.198 0.286 0.396 0.532 0.663 0.834 1.037 1.207 1.559 1.888 2.322 2.859 3.390

410 0.127 0.200 0.289 0.401 0.539 0.671 0.845 1.050 1.222 1.579 1.911 2.351 2.895 3.432

415 0.128 0.203 0.293 0.406 0.545 0.679 0.855 1.062 1.237 1.598 1.935 2.380 2.930 3.474

420 0.130 0.205 0.296 0.411 0.552 0.688 0.865 1.075 1.252 1.617 1.958 2.408 2.965 3.515

425 0.131 0.208 0.300 0.416 0.558 0.696 0.876 1.088 1.267 1.636 1.981 2.437 3.001 3.557

430 0.133 0.210 0.303 0.421 0.565 0.704 0.886 1.101 1.281 1.656 2.005 2.466 3.036 3.599

435 0.134 0.213 0.307 0.425 0.572 0.712 0.896 1.114 1.296 1.675 2.028 2.494 3.071 3.641

440 0.136 0.215 0.310 0.430 0.578 0.720 0.906 1.126 1.311 1.694 2.051 2.523 3.106 3.683

445 0.137 0.218 0.314 0.435 0.585 0.728 0.917 1.139 1.326 1.713 2.075 2.552 3.142 3.725

450 0.139 0.220 0.317 0.440 0.591 0.737 0.927 1.152 1.341 1.733 2.098 2.580 3.177 3.767

455 0.140 0.222 0.321 0.445 0.598 0.745 0.937 1.165 1.356 1.752 2.121 2.609 3.212 3.808

460 0.142 0.225 0.324 0.450 0.604 0.753 0.948 1.178 1.371 1.771 2.145 2.638 3.248 3.850

465 0.144 0.227 0.328 0.455 0.611 0.761 0.958 1.190 1.386 1.790 2.168 2.666 3.283 3.892

470 0.145 0.230 0.331 0.460 0.618 0.769 0.968 1.203 1.401 1.810 2.191 2.695 3.318 3.934

475 0.147 0.232 0.335 0.465 0.624 0.778 0.979 1.216 1.416 1.829 2.214 2.724 3.354 3.976

480 0.148 0.235 0.338 0.469 0.631 0.786 0.989 1.229 1.430 1.848 2.238 2.752 3.389 4.018

485 0.150 0.237 0.342 0.424 0.637 0.794 0.999 1.242 1.445 1.867 2.261 2.781 3.424 4.059

490 0.151 0.240 0.345 0.479 0.644 0.802 1.009 1.254 1.460 1.887 2.284 2.810 3.459 4.101

495 0.153 0.242 0.349 0.484 0.650 0.810 1.020 1.267 1.475 1.906 2.308 2.838 3.495 4.143

500 0.154 0.244 0.353 0.489 0.657 0.819 1.030 1.280 1.490 1.925 2.331 2.867 3.530 4.185

d

l

ACC/DIN 976 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 24: Esparragos y Tornillos Catalogo Tecnico

23DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

dl

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M42 M45 M48 M52 M56 M60 M64 M68 M72 M76 M80 M85 M90 M9550 0.493 0.570 0.647 0.770 0.874 1.001 1.156 1.318 1.475 1.674 1.804 2.044 2.300 2.571

55 0.542 0.626 0.711 0.847 0.961 1.101 1.272 1.449 1.623 1.841 1.984 2.249 2.530 2.829

60 0.592 0.683 0.776 0.924 1.049 1.201 1.387 1.581 1.770 2.008 2.164 2.453 2.760 3.086

65 0.641 0.740 0.840 1.001 1.136 1.301 1.503 1.713 1.918 2.176 2.345 2658 2.990 3.343

70 0.690 0.797 0.905 1.078 1.224 1.401 1.618 1.845 2.065 2.343 2.525 2.862 3.220 3.600

75 0.740 0.854 0.970 1.155 1.311 1.502 1.734 1.976 2.213 2.510 2.705 3.067 3.451 3.857

80 0.789 0.911 1.034 1.232 1.398 1.602 1.850 2.108 2.360 2.678 2.886 3.271 3.681 4.114

85 0.838 0.968 1.099 1.309 1.486 1.702 1.965 2.240 2.508 2.845 3.066 3.475 3.911 4.371

90 0.887 1.025 1.164 1.386 1.573 1.802 2.081 2.372 2.655 3.012 3.246 3.680 4.141 4.629

95 0.937 1.082 1.228 1.463 1.661 1.902 2.196 2.503 2.803 3.180 3.427 3.884 4.371 4.886

100 0.986 1.139 1.293 1.540 1.748 2.002 2.312 2.635 2 950 3.347 3.607 4.089 4.601 5.143

105 1.035 1.196 1.358 1 617 1.835 2.102 2.428 2.767 3.098 3.514 3.787 4.293 4.831 5.400

110 1.085 1.253 1.422 1.694 1.923 2.202 2.543 2.899 3.245 3.682 3.968 4.498 5.061 5.657

115 1.134 1.310 1.487 1.771 2.010 2.302 2.659 3.030 3.393 3.849 4.148 4.702 5.291 5.914

120 1.183 1.367 1.552 1.848 2.098 2.402 2.774 3.162 3.540 4.016 4.328 4.907 5.521 6.171

125 1.233 1.424 1.616 1.925 2.185 2.503 2.890 3.294 3.688 4.184 4.509 5.111 5.751 6.428

130 1.282 1.481 1.681 2.002 2.272 2.603 3.006 3.426 3.835 4.351 4.689 5.315 5.981 6.686

135 1.331 1.538 1.746 2.079 2.360 2.703 3.121 3.557 3.983 4.518 4.870 5.520 6.211 6.943

140 1.380 1.595 1.810 2.156 2.447 2.803 3.237 3.689 4.130 4.686 5.050 5.724 6.441 7.200

145 1.430 1.652 1.875 2.233 2.535 2.903 3.352 3.821 4.278 4.853 5.230 5.929 6.671 7.457

150 1.479 1.709 1.940 2.310 2.622 3.003 3.468 3.953 4.425 5.021 5.411 6.133 6.901 7.714

155 1.528 1.765 2.004 2.387 2.709 3.103 3.584 4.084 4.573 5.188 5.591 6.338 7.131 7.971

160 1.578 1.822 2.069 2.464 2.797 3.203 3.699 4.216 4.720 5.355 5.77! 6.542 7.361 8.228

165 1.627 1.879 2.133 2.541 2.884 3.303 3.815 4.348 4.868 5.523 5.952 6.747 7.591 8.486

170 1.676 1.936 2.198 2618 2.972 3.403 3.930 4.480 5.015 5.690 6.132 6.951 7.821 8.743

175 1.726 1.993 2.263 2.695 3.059 3.504 4.046 4.611 5.163 5.857 6.312 7.155 8.051 9.000

180 1.775 2.050 2.327 2.772 3.146 3.604 4.162 4.743 5.310 6.025 6.493 7.360 8.281 9.257

185 1.824 2.107 2.392 2.849 3.234 3.704 4.277 4.875 5.458 6.192 6.673 7.564 8.511 9.514

190 1.873 2.164 2.457 2.926 3.321 3.804 4.393 5.007 5.605 6.359 6.853 7.769 8.741 9.771

195 1.923 2.221 2.521 3.003 3.409 3.904 4.508 5.138 5.753 6.527 7.034 7.973 8.971 10.028

200 1.972 2.278 2.586 3.080 3.496 4.004 4.624 5.270 5.900 6.694 7.214 8.178 9.201 10.286

205 2.021 2.335 2.651 3.157 3.583 4.104 4.740 5.402 6.048 6.861 7.395 8.382 9.431 10.543

210 2.071 2.392 2.715 3.234 3.671 4.204 4.855 5.534 6.195 7.029 7.575 8.586 9.661 10.800

215 2.120 2.449 2.780 3.311 3.758 4.304 4.971 5.665 6.343 7.196 7.755 8.791 9.892 11.057

220 2.169 2.506 2.845 3.388 3.846 4.404 5.086 5.797 6.490 7.363 7.936 8.995 10.122 11.314

225 2.219 2.563 2.909 3.465 3.933 4.505 5.202 5.929 6.638 7.531 8.116 9.200 10.352 11.571

230 2.268 2.620 2.974 3.542 4.020 4.605 5.318 6.061 6.785 7.698 8.296 9.404 10.582 11.828

235 2.317 2.677 3.039 3.619 4.108 4.705 5.433 6.192 6.933 7.865 8.477 9.609 10.812 12.086

240 2.366 2.734 3.103 3.696 4.195 4.805 5.549 6.324 7.080 8.033 8.657 9.813 11.042 12.343

245 2.416 2.791 3.168 3.773 4.283 4.905 5.664 6.456 7.228 8.200 8.837 10.018 11.272 12.600

250 2.465 2.848 3.233 3.850 4.370 5.005 5.780 6.588 7.375 8.368 9.018 10.222 11.502 12.857

255 2.514 2.904 3.297 3.927 4.457 5.105 5.896 6.719 7.523 8.535 9.198 10.426 11.732 13.114

260 2.564 2.961 3.362 4.004 4.545 5.205 6.011 6.851 7.670 8.702 9.378 10.631 11.962 13.371

265 2.613 3.018 3.426 4.081 4.632 5.305 6.127 6.983 7.818 8.870 9.559 10.835 12.192 13.628

270 2.662 3.075 3.491 4.158 4.720 5.405 6.242 7.115 7.965 9.037 9.739 11.040 12.422 13.886

275 2.712 3.132 3.556 4.235 4.807 5.506 6.358 7.246 8.113 9.204 9.919 11.244 12.652 14.143

ACC/DIN 976 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 25: Esparragos y Tornillos Catalogo Tecnico

24DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

dl

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M42 M45 M48 M52 M56 M60 M64 M68 M72 M76 M80 M85 M90 M95280 2.761 3.189 3.620 4.312 4.894 5.606 6.474 7.378 8.260 9.372 10.100 11.449 12.882 14.400

285 2.810 3.246 3.685 4.389 4.982 5.706 6.589 7.510 8.408 9.539 10.280 11.653 13.112 14.657

290 2.859 3.303 3.750 4.466 5.069 5.806 6.705 7.642 8.555 9.706 10.461 11.858 13.342 14.914

295 2.909 3.360 3.814 4.543 5.157 5.906 6.820 7.773 8.703 9.874 10.641 12.062 13.572 15.171

300 2.958 3.417 3.879 4.620 5.244 6.006 6.936 7.905 8.850 10.041 10.821 12.266 13.802 15.428

305 3.007 3.474 3.944 4.697 5.331 6.106 7.052 8.037 8.998 10.208 11.002 12.471 14.032 15.686

310 3.057 3.531 4.008 4.774 5.419 6.206 7.167 8.169 9.145 10.376 11.182 12.675 14.262 15.943

315 3.106 3.588 4.073 4.851 5.506 6.306 7.283 8.300 9.293 10.543 11.362 12.88 14.492 16.200

320 3.155 3.645 4.138 4.928 5.594 6.406 7.398 8.432 9.440 10.710 11.543 13.084 14.722 16.457

325 3.205 3.702 4.202 5.005 5.681 6.507 7.514 8.564 9.588 10.878 11.723 13.289 14.952 16.714

330 3.254 3.759 4.267 5.082 5.768 6.607 7.630 8.696 9.735 11.045 11.903 13.493 15.182 16.971

335 3.303 3.816 4.332 5.159 5.856 6.707 7.745 8.827 9.883 11.212 12.084 13.697 15.412 17.228

340 3.352 3.873 4.396 5.236 5.943 6.807 7.861 8.959 10.030 11.380 12.264 13.902 15.642 17.486

345 3.402 3.930 4.461 5.313 6.031 6.907 7.976 9.091 10.178 11.547 12.444 14.106 15.872 17.743

350 3.451 3.987 4.526 5.390 6.118 7.007 8.092 9.223 10.325 11.715 12.625 14.311 16.102 18.000

355 3.500 4.043 4.590 5.467 6.205 7.107 8.208 9.354 10.473 11.882 12.805 14.515 16.333 18.257

360 3.550 4.100 4.655 5.544 6.293 7.207 8.323 9.486 10.620 12.049 12.985 14.720 16.563 18.514

365 3.599 4.157 4.719 5.621 6.380 7.307 8.439 9.618 10.768 12.217 13.166 14.924 16.793 18.771

370 3.648 4.214 4.784 5.698 6.468 7.407 8.554 9.750 10.915 12.384 13.346 15.129 17.023 19.028

375 3.698 4.271 4.849 5.275 6.555 7.508 8.670 9.881 11.063 12.551 13.527 15.333 17.253 19.285

380 3.747 4.328 4.913 5.852 6.642 7.608 8.786 10.013 11.210 12.719 13.707 15.537 17.483 19.543

385 3.796 4.385 4.978 5.929 6.730 7.708 8.901 10.145 11.358 12.886 13.887 15.742 17.713 19.800

390 3.845 4.442 5.043 6.006 6.817 7.808 9.017 10.277 11.505 13.053 14.068 15.946 17.943 20.057

395 3.895 4.499 5.107 6.083 6.905 7.908 9.132 10.408 11.653 13.221 14.248 16.151 18.173 20.314

400 3.944 4.556 5.172 6.160 6.992 8.008 9.248 10.540 11.800 13.388 14.428 16.355 18.403 20.571

405 3.993 4.613 5.237 6.237 7.079 8.108 9.364 10.672 11.948 13.555 14.609 16.560 18.633 20.828

410 4.043 4.620 5.301 6.314 7.167 8.208 9.479 10.804 12.095 13.723 14.789 16.764 18.863 21.085

415 4.092 4.727 5.366 6.391 7.254 8.308 9.595 10.935 12.430 13.890 14.969 16.969 19.093 21.343

420 4.141 4.784 5.431 6.468 7.342 8.408 9.710 11.067 12.390 14.057 15.150 17.173 19.323 21.600

425 4.191 4.841 5.495 6.545 7.429 8.509 9.826 11.199 12.538 14.225 15.330 17.377 19.553 21.857

430 4.240 4.898 5.560 6.622 7.516 8.609 9.942 11.331 12.685 14.392 15.510 17.582 19.783 22.114

435 4.289 4.955 5.625 6.699 7.604 8.709 10.057 11.462 12.833 14.559 15.691 17.786 20.013 22.371

440 4.338 5.012 5.689 6.776 7.691 8.809 10.173 11.594 12.980 14.727 15.871 17.991 20.243 22.628

445 4.388 5.069 5.754 6.853 7.779 8.909 10.288 11.726 13.128 14.894 16.051 18.195 20.473 22.885

450 4.437 5.126 5.819 6.930 7.866 9.009 10.404 11.858 13.275 15.062 16.232 18.400 20.703 23.143

455 4.486 5.182 5.883 7.007 7.953 9.109 10.520 11.989 13.423 15.229 16.412 18.604 20.933 23.400

460 4.536 5.239 5.948 7.084 8.041 9.209 10.635 12.121 13.570 15.396 16.593 18.808 21.163 23.657

465 4.585 5.296 6.012 7.161 8.128 9.309 10.751 12.253 13.718 15.564 16.773 19.013 21.393 23.914

470 4.634 5.353 6.077 7238 8.216 9.409 10.866 12.385 13.865 15.731 16.953 19.217 21.623 24.171

475 4.684 5.410 6.142 7.315 8.303 9.510 10.982 12.516 14.013 15.898 17.134 19.422 21.853 24.428

480 4.733 5.467 6.206 7.392 8.390 9.610 11.098 12.648 14.160 16.066 17.314 19.626 22.083 24.685

485 4.782 5.524 6.271 7.469 8.478 9.710 11.213 12.780 14.308 16.233 17.494 19.831 22.313 24.943

490 4.831 5.581 6.336 7.546 8.565 9.810 11.329 12.912 14.455 16.400 17.675 20.035 22.543 25.200

495 4.881 5.638 6.400 7.623 8.653 9.910 11.444 13.043 14.603 16.568 17.855 20.240 22.773 25.457

500 4.930 5.695 6.465 7.700 8.740 10.010 11.560 13.175 14.750 16.735 18.035 20.444 23.004 25.714

ACC/DIN 976 - Totalmente roscados sin tuercas / Totally threaded without nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 26: Esparragos y Tornillos Catalogo Tecnico

25DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

1/8” 7/16” 1/2” 9/16” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.3/8” 1.1/2” 1.5/8” 1.3/4”

50 2” 0.054 0.073 0.108 0.135 0.172 0.279 0.400 0.554 0.747 0.960 1.229 1.543 1.950 2.333

55 2.1/4” 0.056 0.076 0.113 0.140 0.178 0.289 0.413 0.571 0.768 0.988 1.263 1.583 1.997 2.389

60 2.3/8” 0.058 0.079 0.117 0.145 0.184 0.298 0.425 0.587 0.790 1.015 1.296 1.623 2.045 2.444

65 2.1/2” 0.061 0.082 0.121 0.150 0.191 0.307 0.438 0.604 0.812 1.042 1.329 1.663 2.092 2.500

70 2.3/4” 0.063 0.085 0.125 0.155 0.197 0.317 0.451 0.621 0.833 1.069 1.362 1.703 2.139 2.555

75 3” 0.065 0.087 0.129 0.160 0.203 0.326 0.464 0.638 0.855 1.096 1.396 1.743 2.187 2.611

80 3.1/8” 0.067 0.090 0.133 0.165 0.210 0.335 0.477 0.655 0.876 1.123 1.429 1.783 2.234 2.666

85 3.1/4” 0.069 0.093 0.137 0.170 0.216 0.345 0.489 0.671 0.898 1.151 1.462 1.823 2.282 2.722

90 3.1/2” 0.071 0.096 0.141 0.174 0.122 0.354 0.502 0.688 0.920 1.178 1.495 1.863 2.329 2.777

95 3.3/4” 0.074 0.099 0.145 0.179 0.229 0.363 0.515 0.705 0.940 1.205 1.529 1.903 2.376 2.833

100 4” 0.076 0.102 0.149 0.184 0.235 0.373 0.528 0.722 0.963 1.232 1.562 1.943 2.424 2.888

105 4.1/8” 0.078 0.105 0.153 0.189 0.242 0.382 0.541 0.730 0.985 1.259 1.595 1.983 2.471 2.944

110 4.1/4” 0.080 0.108 0.157 0.194 0.248 0.391 0.553 0.755 1.006 1.286 1.628 2.023 2.519 2.999

115 4.1/2” 0.082 0.111 0.161 0.199 0.254 0.401 0.566 0.772 1.028 1.313 1.662 2.063 2.566 3.055

120 4.3/4” 0.084 0.114 0.165 0.204 0.261 0.410 0.579 0.789 1.050 1.341 1.695 2.103 2.613 3.110

125 5” 0.086 0.117 0.169 0.209 0.267 0.420 0.592 0.806 1.071 1.368 1.728 2.143 2.661 3.166

130 5.1/8” 0.089 0.120 0.173 0.214 0.273 0.429 0.605 0.823 1.093 1.395 1.761 2.183 2.708 3.221

135 5.1/4” 0.091 0.123 0.177 0.219 0.28 0.438 0.617 0.839 1.115 1.422 1.795 2.231 2.756 3.277

140 5.1/2” 0.093 0.126 0.181 0.224 0.286 0.448 0.630 0.856 1.136 1.449 1.828 2.263 2.803 3.330

145 5.3/4” 0.095 0.128 0.185 0.229 0.292 0.457 0.643 0.870 1.158 1.476 1.861 2.304 2.850 3.388

150 6” 0.097 0.131 0.189 0.234 0.299 0.466 0.656 0.890 1.180 1.503 1.894 2.344 2.898 3.443

155 6.1/8” 0.099 0.134 0.193 0.239 0.305 0.476 0.669 0.907 1.201 1.531 1.928 2.384 2.945 3.499

160 6.1/4” 0.102 0.137 0.197 0.244 0.311 0.485 0.681 0.923 1.223 1.558 1.961 2.424 2.993 3.554

165 6.1/2” 0.104 0.140 0.201 0.249 0.318 0.494 0.694 0.940 1.245 1.585 1.994 2.464 3.040 3.610

170 6.3/4” 0.106 0.143 0.205 0.254 0.324 0.504 0.707 0.957 1.266 1.612 2.027 2.504 3.087 3.665

175 6.7/8” 0.108 0.146 0.209 0.259 0.330 0.513 0.720 0.974 1.288 1.639 2.961 2.544 3.135 3.721

180 7” 0.110 0.149 0.213 0.264 0.337 0.522 0.733 0.991 1.309 1.666 2.094 2.584 3.182 3.776

185 7.1/4” 0.112 0.152 0.217 0.269 0.343 0.532 0.745 1.007 1.331 1.694 2.127 2.624 3.230 3.832

190 7.1/2” 0.114 0.155 0.221 0.224 0.349 0.541 0.758 1.024 1.353 1.721 2.160 2.664 3.277 3.887

195 7.3/4” 0.117 0.158 0.225 0.279 0.356 0.550 0.771 1.041 1.374 1.748 2.194 2.704 3.324 3.943

200 7.7/8” 0.119 0.161 0.229 0.284 0.362 0.560 0.784 1.058 1.396 1.775 2.227 2.744 3.372 3.998

205 8” 0.121 0.164 0.233 0.289 0.369 0.569 0.797 1.075 1.418 1.802 2.260 2.784 3.419 4.054

210 8.1/4” 0.123 0.167 0.237 0.294 0.375 0.578 0.809 1.091 1.439 1.829 2.293 2.824 3.467 4.109

215 8.1/2” 0.125 0.169 0.241 0.299 0.381 0.588 0.822 1.108 1.461 1.856 2.327 2.864 3.514 4.165

220 8.3/4” 0.127 0.172 0.245 0.304 0.388 0.597 0.835 1.125 1.483 1.884 2.360 2.904 3.561 4.220

225 8.7/8” 0.130 0.175 0.249 0.309 0.394 0.607 0.848 1.142 1.504 1.911 2.393 2.944 3.609 4.276

230 9” 0.132 0.178 0.253 0.314 0.400 0.616 0.861 1.159 1.526 1.938 2.426 2.984 3.656 4.331

235 9.1/4” 0.134 0.181 0.257 0.319 0.407 0.625 0.873 1.175 1.548 1.965 2.460 3.024 3.704 4.387

240 9.1/2” 0.136 0.184 0.261 0.324 0.413 0.635 0.886 1.192 1.569 1.992 2.493 3.064 3.751 4.442

245 9.5/8” 0.138 0.187 0.265 0.329 0.419 0.644 0.899 1.209 1.591 2.019 2.526 3.105 3.798 4.498

250 9.3/4” 0.140 0.19 0.269 0.334 0.426 0.653 0.912 1.226 1.613 2.046 2.559 3.145 3.846 4.553

255 10” 0.142 0.193 0.274 0.339 0.432 0.663 0.925 1.243 1.634 2.074 2.593 3.185 3.893 4.609

260 10.1/4” 0.145 0.196 0.278 0.344 0.438 0.672 0.937 1.259 1.656 2.101 2.626 3.225 3.941 4.664

265 10.1/2” 0.147 0.199 0.282 0.349 0.445 0.681 0.950 1.276 1.678 2.128 2.659 3.265 3.988 4.720

270 10.5/8” 0.149 0.202 0.286 0.354 0.451 0.691 0.963 1.293 1.699 2.155 2.692 3.305 4.035 4.775

275 10.3/4” 0.151 0.205 0.290 0.359 0.457 0.700 0.976 1.310 1.221 2.182 2.726 3.345 4.083 4.831

ACC/B16.5 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 27: Esparragos y Tornillos Catalogo Tecnico

26DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

3/8” 7/16” 1/2” 9/16” 5/8” 3/4” 7/8” 1” 1.1/8” 1.1/4” 1.3/8” 1.1/2” 1.3/8” 1.3/4”

280 11” 0.153 0.208 0.294 0.364 0.464 0.709 0.989 1.327 1.742 2.209 2.759 3.385 4.130 4.886

285 11.1/4” 0.155 0.210 0.298 0.369 0.470 0.719 1.001 1.343 1.764 2.237 2.792 3.425 4.178 4.942

290 11.1/2” 0.158 0.213 0.302 0.374 0.476 0.728 1.014 1.360 1.786 2.264 2.825 3.465 4.225 4.997

295 11.5/8” 0.160 0.216 0.306 0.379 0.483 0.737 1.027 1.377 1.807 2.291 2.859 3.505 4.272 5.053

300 11.3/4” 0.162 0.219 0.310 0.384 0.489 0.747 1.040 1.394 1.829 2.318 2.892 3.545 4.320 5.108

305 12” 0.164 0.222 0.314 0.389 0.496 0.756 1.053 1.411 1.851 2.345 2.925 3.585 4.367 5.164

310 12.1/4” 0.166 0 225 0.318 0.394 0.502 0.765 1.065 1.427 1.872 2.372 2.958 3.625 4.415 5.219

315 12.1/2” 0.168 0.228 0.322 0.399 0.508 0.775 1.078 1.461 1.894 1.399 2.992 3.705 4.462 5.275

320 12.5/8” 0.170 0.231 0.326 0.404 0515 0.784 1.091 1.461 1.916 2.427 3.025 3.705 4.509 5.330

325 12.3/4” 0.173 0.234 0.330 0.409 0.521 0.794 1.104 1.478 1.937 2.454 3.058 3.745 4.557 5.386

330 13” 0.175 0.237 0.334 0.414 0.527 0.803 1.117 1.495 1.959 2.481 3.091 3.785 4.604 5.441

335 13.1/4” 0.177 0.240 0.338 0.419 0.534 0.812 1.129 1.511 1.981 2.508 3.125 3.825 4.652 5.497

340 13.3/8” 0.179 0.243 0.342 0.424 0.540 0.822 1.142 1.528 2.002 2.535 3.158 3.865 4.699 5.552

345 13.1/2” 0.181 0.246 0.346 0.429 0.546 0.831 1.155 1.545 2.024 2.562 3.191 3.906 4.746 5.608

350 13.3/4” 0.183 0.249 0.350 0.434 0.553 0.840 1.168 1.562 2.046 2.589 3.224 3.946 4.794 5.663

355 14” 0.186 0.251 0.354 0.439 0.559 0.850 1.181 1.579 2.067 2.617 3.258 3.986 4.841 5.719

360 14.1/4” 0.188 0.254 0.358 0.444 0.565 0.859 1.193 1.595 2.089 2.644 3.291 4.026 4.889 5.774

365 14.3/8” 0.190 0.257 0.362 0.449 0.572 0.868 1.206 1.612 2.111 2.671 3.324 4.061 4.936 5.830

370 14.1/2” 0.192 0.260 0.366 0.454 0.578 0.878 1.219 1.629 2.132 2.698 3.357 4.106 4.983 5.885

375 14.3/4” 0.194 0.263 0.370 0.459 0.584 0.887 1.232 1.646 2.154 2.725 3.391 4.146 5.031 5.941

380 15” 0.196 0.266 0.374 0.464 0.591 0.896 1.245 1.663 2.175 2.752 3.424 4.186 5.078 5.996

385 15.1/4” 0.199 0.269 0.378 0.469 0.597 0.906 1.257 1.679 2.197 2.780 3.457 4.226 5.126 6.052

390 15.3/8” 0.201 0.272 0.382 0.474 0.603 0.915 1.270 1.696 2.219 2.807 3.490 4.266 5.173 6.107

395 15.1/2” 0.203 0.275 0.386 0.479 0.610 0.924 1.283 1.713 2.240 2.834 3.524 4.306 5.220 6.163

400 15.3/4” 0.205 0.278 0.390 0.483 0.616 0.934 1.296 1.730 2.262 2.861 3.557 4.346 5.268 6.218

405 16” 0.207 0.281 0.394 0.488 0.623 0.943 1.309 1.747 2.284 2.888 3.590 4.386 5.315 6.274

410 16.1/4” 0.209 0.284 0.398 0.493 0.629 0.952 1.327 1.763 2.305 2.915 3.623 4.426 5.363 6.329

415 16.3/8” 0.211 0.287 0.402 0.498 0.635 0.962 1.334 1.780 2.327 2.942 3.657 4.466 5.410 6.385

420 16.1/2” 0.214 0.290 0.406 0.503 0.642 0.971 1.347 1.797 2.349 2.970 3.690 4.506 5.457 6.440

425 16.3/4” 0.216 0.292 0.410 0.508 0.648 0.981 1.360 1.814 2.370 2.997 3.723 4.546 5.505 6.496

430 17” 0.218 0.295 0.414 0.513 0.654 0.990 1.373 1.831 2.392 3.024 3.756 4.586 5.552 6.551

435 17.1 1/8” 0.220 0.298 0.418 0.518 0.661 0.999 1.385 1.847 2.414 3.051 3.790 4.626 5.600 6.607

440 17.1 1/4” 0.222 0.301 0.422 0.523 0.667 1.009 1.398 1.864 2.435 3.078 3.823 4.666 5.647 6.662

445 17.1/2” 0.224 0.304 0.426 0.528 0.673 1.018 1.411 1.881 2.457 3.105 3.856 4.707 5.694 6.718

450 17.3/4” 0.227 0.307 0.430 0.533 0.680 1.027 1.424 1.898 2.479 3.132 3.889 4.747 5.742 6.773

455 18” 0.229 0.310 0.435 0.538 0.686 1.037 1.437 1.915 2.500 3.160 3.923 4.787 5.789 6.829

460 18.1/8” 0.231 0.313 0.439 0.543 0.692 1.046 1.449 1.931 2.522 3.187 3.956 4.827 5.837 6.884

465 18.1/4” 0.233 0.316 0.443 0.548 0.699 1.055 1.462 1.948 2.544 3.214 3.989 4.867 5.884 6.940

470 18.1/2” 0.235 0.319 0.447 0.553 0.705 1.065 1.475 1.965 2.565 3.241 4.022 4.907 5.931 6.995

475 18.3/4” 0.237 0.322 0.451 0.558 0.711 1.074 1.488 1.982 2.587 3.268 4.056 4.947 5.979 7.051

480 18.7/8” 0.239 0.325 0.455 0.563 0.718 1.083 1.501 1.999 2.608 3.295 4.089 4.987 6.026 7.106

485 19” 0.242 0.328 0.459 0.568 0.724 1.093 1.513 2.015 2.630 3.323 4.122 5.027 6.074 7.162

490 19.1/4” 0.244 0.331 0.463 0.573 0.730 1.102 1.526 2.032 2.652 3.350 4.155 5.067 6.121 7.217

495 19.1/2” 0.246 0.333 0.467 0.578 0.737 1.111 1.539 2.049 2.673 3.377 4.189 5.107 6.168 7.273

500 19.3/4” 0.248 0.336 0.471 0.583 0.743 1.127 1.552 1.066 2.695 3.404 4.222 5.147 6.216 7.328

d

l

ACC/B16.5 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 28: Esparragos y Tornillos Catalogo Tecnico

27DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

1.7/8” 2” 2.1/4” 2.1/2” 2.3/4” 3” 3.1/4 3.1/2” 3.3/4” 4”50 2” 2. 830 3.394 4.667 6.282 7.953 9.769 11.970 15.499 18.579 22.948

55 2.1/4” 2.894 3.467 4.761 6.398 8.094 9.938 12.173 15.735 18.844 23.253

60 2.3/8” 2.958 3.540 4.854 6.515 8.236 10.108 12.375 15.971 19.109 23.557

65 2.1/2” 3.022 3.613 4.948 6.631 8.377 10.277 12.578 16.207 19.374 23.862

70 2.3/4” 3.086 3.686 5.041 6.748 8.519 10.447 12.780 16.443 19.639 24.166

75 3” 3.150 3.759 5.135 6.864 8.660 10.616 12.983 16.679 19.904 24.470

80 3.1/8” 3.214 3.832 5.228 6.981 8.802 10.850 13.185 16.679 19.904 24.470

85 3.1/4” 3.278 3.905 5.322 7.097 8.943 10.955 13.388 17.151 20.434 25.079

90 3.1/2” 3.342 3.978 5.415 7.214 9.085 11.125 13.590 17.387 20.699 25.384

95 3.3/4” 3.406 4.051 5.509 7.330 9.226 11.294 13.793 17.623 20.964 25.688

100 4” 3 470 4.124 5.602 7.447 9.368 11.464 13.995 17.859 21.229 25.992

105 4.1/8” 3.534 4.197 5.696 7.563 9.509 11.633 14.198 18.095 21.494 26.297

110 4.1/4” 3.598 4.270 5.789 7.680 9.651 11.803 14.400 18.331 71.759 26.601

115 4.1/2” 3.662 4.343 5.883 7.796 9.792 11.972 14.603 18.567 22.024 26.906

120 4.3/4” 3.716 4.416 5.976 7.913 9.934 12.142 14.805 18.803 22.289 27.210

125 5” 3.790 4.489 6.070 8.029 10.075 12.311 15.008 19.039 22.554 27.514

130 5.1/8” 3.854 4.562 6.163 8.146 10.217 12.481 15.210 19.275 22.819 27.819

135 5.1/4” 3.918 4.635 6.257 8.262 10.358 12.650 15.413 19.511 23.084 28.123

140 5.1/2” 3.982 4.708 6.350 8.379 10.500 12.820 15.615 19.747 23.349 28.428

145 5.3/4” 4.046 4.781 6.444 8.495 10.641 12.989 15.818 19.983 23.614 28.732

150 6” 4.110 4.854 6.537 8.612 10.783 13.159 16.020 20.219 23.879 29.036

155 6.1/8” 4.124 4.927 6.631 8.728 10.924 13.328 16.223 20.450 24.144 29.341

160 6.1/4” 4.238 5.073 6.724 8.845 11.066 13.498 16.425 20.691 24.409 29.645

165 6.1/2” 4.302 5.146 6.818 8.961 11.207 13.667 16.628 20.927 24.674 29.950

170 6.3/4” 4.366 5.219 6.911 9.078 11.349 13.837 16.830 21.163 24 939 30.254

175 6.7/8” 4.430 5.292 7.005 9.194 11.490 14.006 17.033 21.399 25.204 30.558

180 7” 4.494 5.365 7.098 9.311 11.632 14.176 17.235 21.635 25.469 30.863

185 7.1/4” 4.558 5.438 7.192 9.427 11.773 14.345 17.438 21.871 25.734 31.167

190 7.1/2” 4.622 5.511 7.285 9.544 11.915 14.515 17.640 22.107 25.999 31.472

195 7.3/4” 4.685 5.584 7.379 9.660 12.056 14.684 17.843 22.343 26.264 31.776

200 7.7/8” 4.750 5.657 7.472 9.777 12.198 14.854 18.045 22.579 26.529 32.080

205 8” 4.814 5.730 7.566 9.893 12.339 15.023 18.048 22.815 26.794 32.385

210 8.1/4” 4.878 5.803 7.639 10.010 12.481 15.193 18.450 23.051 27.059 32.689

215 8.1/2” 4.942 5.803 7.753 10.126 12.622 15.362 18.653 23.287 27.324 32.994

220 8.3/4” 5.006 5.876 7.846 10.246 12.764 15.532 18.855 23.523 27.589 33.298

225 8.7/8” 5.070 5.949 7.940 10.359 12.905 15.701 19.058 23.759 27.854 33.602

230 9” 5.134 6.022 8.033 10.476 13.047 15.871 19.260 23.995 28.119 33.907

235 9.1/4” 5.198 6.095 8.127 10.592 13.188 16.040 19.463 24.231 28.384 34.211

240 9.1/2” 5.262 6.168 8.220 10.709 13.330 16.210 19.665 24.467 28.649 34.516

245 9.5/8” 5.326 6.241 8.314 10.825 13.471 16.379 19.868 24.703 28.914 34.820

250 9.3/4” 5.390 6.314 8.407 10.942 13.613 16.549 20.070 24.939 29.179 35.124

255 10” 5.454 6.387 8.501 11.058 13.754 16.718 20.273 25.175 29.444 35.429

260 10.1/4” 5.518 6.460 8.594 11.175 13.896 16.888 20.475 25.411 29.709 35.733

265 10.1/2” 5.582 6.533 8.688 11.291 14.037 17.057 20.678 25.647 29.974 36.038

270 10.5/8” 5.646 6.606 8.781 11.408 14.179 17.227 20.880 25.883 30.239 36.342

275 10.3/4” 5.710 6.679 8.875 11.524 14.320 17.396 21.083 26.119 30.504 36.646

ACC/B16.5 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 29: Esparragos y Tornillos Catalogo Tecnico

28DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

1.7/8” 2” 2.1/4” 2.1/2” 2.3/4” 3” 3.1/4 3.1/2” 3.3/4” 4”

280 11" 5.774 6.752 8.968 11.641 14.462 17.566 21.285 26.355 30.769 36.951

285 11.1/4" 5.838 6.825 9.062 11.757 14.603 17.735 21.488 26.591 31.034 37.255

290 11.1/2" 5.902 6.898 9.155 11.874 14.745 17.905 21.690 26.827 31.299 37.560

295 11.5/8" 5.966 6.971 9.249 11.990 14.886 18.074 21.893 27.063 31.564 37.864

300 11.3/4" 6.030 7.044 9.342 12.107 15.028 18.244 22.095 27.299 31.829 38.168

305 12" 6.094 7.117 9.436 12.223 15.169 18.413 22.298 27.535 32.094 38.473

310 12.1/4" 6.158 7.190 9.529 12.340 15.311 18.583 22.500 27.771 32.359 38.777

315 12.1/2" 6.222 7.263 9.623 12.456 15.452 18.752 22.703 28.007 32.624 39.082

320 12.5/8" 6.286 7.336 9.716 12.573 15.594 18.922 22.905 28.243 32.889 39.386

325 12.3/4" 6.350 7.409 9.810 12.689 15.735 19.091 23.108 28.479 33.154 39.690

330 13" 6.414 7.482 9.903 12.806 15.877 19.261 23.310 28.715 33 419 39.995

335 13.1/4" 6.478 7.555 9.997 12.922 16.018 19.430 23.513 28.951 33.684 40.299

340 13.3/8" 6.542 7.628 10.090 13.039 16.160 19.600 23.715 29.187 33.949 40.604

345 13.1/2" 6.606 7.701 10.184 13.155 16.301 19.769 23.918 29.423 34.214 40.908

350 13.3/4" 6.670 7.774 10.277 13.272 16.443 19.939 24.120 29.659 34.479 41.212

355 14" 6.734 7.847 10.371 13.388 16.584 20.108 24.323 29.895 34.744 41.517

360 14.1/4" 6.798 7.920 10.464 13.505 16.726 20.278 24.525 30.131 35.009 41.821

365 14.3/8" 6.862 7.993 10.558 13.621 16.867 20.447 24.728 30.367 35.274 42.126

370 14.1/2" 6.926 8.066 10.651 13.738 17.009 20.617 24.930 30.603 35.539 42.430

375 14.3/4" 6.990 8.139 10.745 13.854 17.150 20.786 25.133 30.838 35.804 42.734

380 15" 7.054 8.212 10.838 13.971 17 292 20. 956 25.535 31.075 36.069 43.039

385 15.1/4" 7.118 8.285 10.932 14.087 17.433 21.125 25.538 31.311 36.334 43.343

390 15.3/8" 7.182 8.358 11.025 14.204 17.575 21.295 25.740 31.547 36.599 43.648

395 15.1/2" 7.246 8.431 11.119 14.320 17.716 21.464 25.943 31.783 36.864 43.952

400 15.3/4" 7.310 8.504 11.212 14.437 17.858 21.634 26.145 32.019 37.129 44.256

405 16" 7.374 8.577 11.306 14.553 17.999 21.803 26.348 32.255 37.394 44.561

410 16.1/4" 7.438 8.650 11.399 14.670 18.141 21.973 26.550 32.491 37.659 44.865

415 16.3/8" 7.502 8.723 11.493 14.786 18.282 22.142 26.753 32.727 37.924 45.170

420 16.1/2" 7.566 8.796 11.586 14.903 18.424 22.312 26.955 32.963 38.189 45.474

425 16.3/4" 7.630 8.869 11.680 15.019 18.565 22.481 27.158 33.199 38.454 45.778

430 17" 7.694 8.942 11.773 15.136 18.707 22.651 27.360 33.435 38.719 46.083

435 17.1/8" 7.758 9.015 11.867 15.252 18.848 22.820 27.563 33.671 38.984 46.387

440 17.1/4" 7.822 9.088 11.960 15.369 18.990 22.990 27.765 33.907 39.249 46.692

445 17.1/2" 7.886 9.161 12.054 15.485 19.131 23.159 27.968 34.143 39.514 46.996

450 17.3/4" 7.950 9.234 12.147 15.602 19.273 23.329 28.170 34.379 39.779 47.300

455 18" 8.014 9.307 12.241 15.718 19.414 23.498 28.373 34.615 40.044 47.605

460 18.1/8" 8.078 9.380 12.334 15.835 19.556 23.668 28.575 34.851 40.309 47.909

465 18.1/4" 8.142 9.453 12.428 15.951 19.697 23.837 28.778 35.087 40.574 48.214

470 18.1/2" 8.206 9.526 12.521 16.068 19.839 24.007 28.980 35.323 40.839 48.518

475 18.3/4" 8.270 9.599 12.615 16.184 19.980 24.176 29.183 35.559 41.104 48.822

480 18.7/8" 8.334 9.672 12.708 16.301 20.122 24.346 29.385 35.795 41.369 49.127

485 19" 8.398 9.745 12.802 16.417 20.263 24.515 29.588 36.031 41.634 49.431

490 19.1/4" 8.462 9.818 12.895 16.534 20.405 24.685 29.790 36.267 41.899 49.736

495 19.1/2" 8.526 9.891 12.989 16.650 20.546 24.854 29.993 36.503 42.164 50.040

500 19.3/4" 8.590 9.964 13.082 16.767 20.688 25.024 30.195 36.739 42.429 50.344

ACC/B16.5 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 30: Esparragos y Tornillos Catalogo Tecnico

29DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36 M3950 0.028 0.053 0.076 0.112 0.147 0.198 0.261 0.318 0.423 0.593 0.801 1.009 1.319 1.665

55 0.030 0.055 0.079 0.117 0.153 0.206 0.272 0.331 0.438 0.612 0.824 1.037 1.354 1.706

60 0.032 0.058 0.083 0.121 0.160 0.215 0.282 0.343 0.453 0.631 0.848 1.066 1.390 1.748

65 0.033 0.060 0.086 0.126 0.166 0.223 0.292 0.356 0.468 0.650 0.871 1.095 1.425 1.790

70 0.035 0.063 0.090 0.131 0.173 0.231 0.302 0.369 0.483 0.670 0.894 1.123 1.460 1.832

75 0.036 0.065 0.093 0.136 0.180 0.239 0.313 0.382 0.498 0.689 0.918 1.157 1.496 1 874

80 0.038 0.068 0.097 0.141 0.186 0.247 0.323 0.395 0.512 0.708 0.941 1.181 1.531 1.916

85 0.039 0.070 0.101 0.146 0.193 0.256 0.333 0.407 0.527 0.727 0.964 1.209 1.566 1.957

90 0.041 0.073 0.104 0.151 0.199 0 264 0.344 0.420 0.541 0.747 0.988 1.238 1.601 1.999

95 0.042 0.075 0.108 0.156 0.206 0.272 0.354 0 433 0.557 0.766 1.011 1.267 1.637 2.041

100 0.044 0.077 0.111 0.161 0.212 0.280 0.364 0.446 0.572 0.785 1.034 1.295 1.672 2.083

105 0.045 0.080 0.115 0.165 0.219 0.288 0.375 0.459 0.587 0.804 1.058 1.324 1.707 2.125

110 0.047 0.082 0.118 0.170 0.226 0.296 0.385 0.471 0.602 0.824 1.081 1.353 1.743 2.167

115 0.048 0.085 0.122 0.175 0.232 0.305 0.395 0.484 0.617 0.843 1.104 1.381 1.778 2.209

120 0.050 0.087 0.125 0.180 0.239 0.313 0.405 0.497 0.632 0.862 1.127 1.410 1.813 2.250

125 0.052 0.090 0.129 0.185 0.245 0.321 0.416 0.510 0.647 0.881 1.151 1.439 1.849 2.292

130 0.053 0.092 0.132 0.190 0.252 0.329 0.426 0.523 0.661 0.901 1.174 1.467 1.884 2.334

135 0.055 0.095 0.136 0.195 0.258 0.337 0.436 0.535 0.676 0.920 1.197 1.491 1.919 2.376

140 0.056 0.097 0.139 0.200 0.265 0.346 0.447 0.548 0.691 0.939 1.221 1.525 1.954 2.418

145 0.058 0.100 0.143 0.205 0.272 0.354 0.457 0.561 0.706 0.958 1.244 1.553 1.990 2.460

150 0.059 0.102 0.146 0.210 0.278 0.362 0.467 0.574 0.721 0.978 1.267 1.582 2.025 2.502

155 0.061 0.104 0.150 0.214 0.285 0.370 0.478 0.587 0.736 0.997 1.291 1.611 2.060 2.543

160 0.062 0.107 0.153 0.219 0.291 0 378 0.488 0.599 0 751 1.016 1.314 1.639 2.096 2.585

165 0.064 0.109 0.157 0.224 0.298 0.387 0.498 0.612 0.766 1.035 1.337 1.668 2.131 2.627

170 0.065 0.112 0.160 0.229 0.304 0.395 0.508 0.625 0.781 1.055 1.361 1.697 2.166 2.669

175 0.067 0.114 0.164 0.234 0.311 0.403 0.519 0.638 0.796 1.074 1.384 1.725 2.202 2.711

180 0.069 0.117 0.168 0.239 0.318 0.411 0.529 0.651 0.810 1.093 1.407 1.754 2.237 1.753

185 0.070 0.119 0.171 0.244 0.324 0.419 0.539 0.663 0.825 1.112 1.430 1.783 2.272 2.794

190 0.072 0.122 0.175 0.249 0.331 0.427 0.550 0.676 0.840 1.132 1.454 1.811 2.307 2.836

195 0.073 0.124 0.178 0.254 0.337 0.436 0.560 0.689 0.855 1.151 1.477 1.840 2.343 2.878

200 0.075 0.126 0.182 0.258 0.344 0.444 0.570 0.702 0.870 1.170 1.500 1.869 2.378 2.920

205 0.076 0.129 0.185 0.263 0.350 0.452 0.581 0.715 0.885 1.189 1.524 1.897 2.413 2.962

210 0.078 0.131 0.189 0.268 0.357 0.460 0.591 0.727 0.900 1.209 1.547 1.926 2.449 3.004

215 0.079 0.134 0.192 0.273 0.364 0.468 0.601 0.740 0.915 1.228 1.570 1.955 2.484 3.046

220 0.081 0.136 0.196 0.278 0.370 0.477 0.611 0.753 0.930 1.247 1.594 1.983 2.519 3.087

225 0.082 0.139 0.199 0.283 0.377 0.485 0.622 0.766 0.945 1.266 1.617 2.012 2.555 3.129

230 0.084 0.141 0.203 0.288 0.383 0.493 0.632 0.779 0.959 1.286 1.640 2.041 2.590 3.171

235 0.086 0.144 0,206 0.293 0.390 0.501 0.642 0.791 0.974 1.305 1.664 2.069 2.625 3.213

240 0.087 0.146 0.210 0.298 0.396 0.509 0.653 0.804 0.989 1.324 1.687 2.098 2.660 3.255

245 0.089 0.148 0.213 0.302 0.403 0.517 0.663 0.817 1.004 1.343 1.710 2.127 2.696 3.297

250 0.090 0.151 0.217 0.307 0.410 0.526 0.673 0.830 1.019 1.363 1.734 2.156 2.731 3.339

255 0.092 0.153 0.220 0.312 0.416 0.534 0.684 0.843 1.034 1.382 1.757 2.184 2.766 3.380

260 0.093 0.156 0.224 0.317 0.423 0.542 0.694 0.855 1.049 1.401 1.780 2.213 2.802 3.422

265 0.095 0.158 0.227 0.322 0.429 0.550 0.704 0.868 1.064 1.420 1.803 2.242 2.837 3.464

270 0.096 0.161 0.231 0.327 0.436 0.558 0.714 0.881 1.079 1.440 1.827 2.170 2.872 3.506

275 0.098 0.163 0.234 0.332 0.442 0.567 0.725 0.894 1.094 1.459 1.850 2.299 2.908 3.548

ACC/DIN 976 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 31: Esparragos y Tornillos Catalogo Tecnico

30DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d

l

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECE

M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M33 M36 M39

280 0.099 0.166 0.238 0.337 0.449 0.575 0.735 0.907 1.108 1.478 1.873 2.328 2.943 3.590

285 0.101 0.168 0.242 0.342 0.455 0.583 0.745 0.919 1.123 1.497 1.897 2.356 2.978 3.631

290 0.102 0.170 0.245 0.346 0.462 0.591 0.756 0.932 1.138 1.517 1.920 2.385 3.013 3.673

295 0.104 0.173 0.249 0.351 0.469 0.599 0.766 0.945 1.153 1.536 1.943 2.414 3.049 3.715

300 0.106 0.175 0.252 0.356 0.475 0.608 0.776 0.958 1.168 1.555 1.967 2.442 3.084 3.757

305 0.107 0.178 0.256 0.361 0.482 0.616 0.787 0.971 1.183 1.574 1.990 2.471 3.119 3.799

310 0.109 0.180 0.250 0.366 0.488 0.624 0.792 0.983 1.198 1.594 2.013 2.500 3.155 3.841

315 0.110 0.183 0.263 0.371 0.495 0.632 0.807 0.996 1.213 1.613 2.037 2.528 3.190 3.883

320 0.112 0.185 0.266 0.376 0.501 0.640 0.817 1.009 1.228 1.632 2.060 2.557 3.225 3.924

325 0.113 0.188 0.270 0.381 0.508 0.648 0.828 1.022 1.243 1.651 2.083 2.586 3.261 3.966

330 0.115 0.190 0.273 0.386 0.515 0 657 0.838 1.035 1.257 1.671 2.106 2.614 3.296 4.008

335 0.116 0.192 0.277 0.390 0.521 0.665 0.848 1.047 1.272 1.690 2.130 2.643 3.331 4.050

340 0.118 0.195 0.280 0.395 0.528 0.673 0.859 1.060 1.287 1.709 2.153 2.672 3.366 4.092

345 0.119 0.197 0.284 0.400 0.534 0.681 0.869 1.073 1.302 1.728 2.176 2.700 3.402 4.134

350 0.121 0.200 0.287 0.405 0.541 0.689 0.879 1.086 1.317 1.748 2.200 2.729 3.437 4.176

355 0.123 0.202 0.291 0.410 0.547 0.698 0.890 1.099 1.332 1.767 2.223 2.758 3.472 4.217

360 0 124 0.205 0 294 0.415 0.554 0.706 0.900 1.111 1.347 1 786 2.246 2.786 3.508 4.259

365 0.126 0.207 0.298 0.420 0.561 0.714 0.910 1.124 1.362 1.805 2.270 2.815 3.543 4.301

370 0.127 0.210 0.301 0.425 0.567 0.722 0.920 1.137 1.377 1.825 2.293 2.844 3.578 4.343

375 0.129 0.212 0.305 0.430 0.574 0.730 0.931 1.150 1.392 1.844 2.316 2.872 3.614 4.385

380 0.130 0.214 0.309 0.434 0.580 0 738 0.941 1.163 1.406 1.863 2.340 2.901 3.649 4.427

385 0.132 0.217 0.312 0.439 0.587 0.747 0.951 1.175 1.421 1.882 2.363 2.930 3.684 4.468

390 0.133 0.219 0.316 0.444 0.593 0.755 0.962 1.188 1.436 1.902 2.386 2.958 3.719 4.510

395 0.135 0.222 0.319 0.449 0.600 0.763 0.972 1.201 1.451 1.921 2.409 2.987 3.755 4.552

400 0.136 0.224 0.323 0.454 0.607 0.771 0.982 1.214 1.466 1.940 2.433 3.016 3.790 4.594

405 0.138 0.227 0.326 0.459 0.613 0.779 0.993 1.227 1.481 1.959 2.456 3.044 3.825 4.636

410 0.140 0.229 0 330 0.464 0.620 0.788 1.003 1. 239 1.496 1.979 2.479 3.073 3.861 4.678

415 0.141 0.232 0.333 0.469 0.626 0.796 1.013 1.252 1.511 1.998 2.503 3.102 3.896 4.720

420 0.143 0.234 0.337 0.474 0.633 0.804 1.023 1.265 1.526 2.017 2.526 3.130 3.931 4.761

425 0.144 0.236 0.340 0.478 0.639 0.812 1.034 1.278 1.541 2.036 2.549 3.159 3.967 4.803

430 0.146 0.239 0.344 0.483 0.646 0.820 1.044 1.291 1.555 2.056 2.573 3.188 4.002 4.845

435 0.147 0.241 0.347 0.488 0.653 0.828 1.054 1.303 1.570 2.075 2.596 3.216 4.037 4.887

440 0.149 0.244 0.351 0.493 0.659 0.837 1.065 1.316 1.585 2.094 2.619 3.245 4.072 4.929

445 0.150 0.246 0.354 0.498 0.666 0.845 1.075 1.329 1.600 2.113 2.643 3.274 4.108 4.971

450 0.152 0.249 0.358 0.503 0.672 0.853 1.085 1.342 1.615 2.133 2.666 3.302 4.143 5.013

455 0.153 0.251 0.361 0.508 0.679 0.861 1.096 1.355 1.630 2.152 2.689 3.331 4.178 5.054

460 0.155 0.254 0.365 0.513 0.685 0.869 1.106 1.367 1.645 2.171 2.713 3.360 4.214 5.096

465 0.157 0.256 0.368 0.518 0.692 0.878 1.116 1.380 1.660 2.190 2.736 3.388 4.249 5.138

470 0.158 0.258 0.372 0.522 0.699 0.886 1.126 1.393 1.675 2.210 2.759 3.417 4.284 5.180

475 0.160 0.261 0.375 0.527 0.705 0.894 1.137 1.406 1.690 2.229 2.782 3.446 4.320 5.222

480 0.161 0.263 0.379 0.532 0.712 0.902 1.147 1.419 1.704 2.248 2.806 3.474 4.355 5.264

485 0.163 0.266 0.383 0.537 0.718 0.910 1.157 1.431 1.719 2.267 2.829 3.503 4.390 5.305

490 0.164 0.268 0.386 0.542 0.725 0.919 1.168 1.444 1.734 2.287 2.852 3.532 4.425 5.347

495 0.166 0.271 0.390 0.547 0.731 0.927 1.178 1.457 1.749 2.306 2.876 3.560 4.461 5.389

500 0.167 0.273 0.393 0.552 0.738 0.935 1.188 1.470 1.764 2.325 2.899 3.589 4.496 5.431

ACC/DIN 976 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 32: Esparragos y Tornillos Catalogo Tecnico

31DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECEM42 M45 M48 M52 M56 M60 M64 M68 M72 M76 M80 M85 M90 M95

50 2.083 2.546 3.087 3.710 4.414 5.161 6.056 6.998 8.015 9.154 10.304 11.704 14.420 16.171

55 2.132 2.602 3.151 3.787 4.501 5.261 6.172 7.129 8.163 9.321 10.484 11.909 14.650 16.429

60 2.182 2.659 3.216 3.864 4.589 5.361 6.287 7.261 8.310 9.488 10.664 12.113 14.880 16.686

65 2.231 2.716 3.280 3.941 4.676 5.461 6.403 7.393 8.458 9.656 10.845 12.318 15.110 16.943

70 2.280 2.773 3.345 4.018 4.764 5.561 6.518 7.525 8.605 9.823 11.025 12.522 15.340 17.200

75 2.330 2.830 3.410 4.095 4.851 5.662 6.634 7.656 8.753 9.990 11.205 12.727 15.571 17.457

80 2.379 2.887 3.474 4.172 4.938 5.762 6.750 7.788 8.900 10.158 11.386 13.931 15.801 17.714

85 2.428 2.944 3.539 4.249 5.026 5.862 6.865 7.920 9.048 10.325 11.566 13.135 16.031 17.971

90 2.477 3.001 3.604 4.326 5.113 5.962 6.981 8.052 9.195 10.492 11.746 13.340 16.261 18.229

95 2.527 3.058 3.668 4.403 5.201 6.062 7.096 8.183 9.343 10.660 11.927 13.544 16.491 18.486

100 2.576 3.115 3.733 4.480 5.288 6.162 7.212 8.315 9.490 10.827 12.107 13.749 16.721 18.743

105 2.625 3.172 3.798 4.557 5.375 6.262 7.328 8.447 9.638 10.994 12.287 13.953 16.951 19.000

110 2.675 3.229 3.862 4.634 5.463 6.362 7.443 8.579 9.785 11.162 12.468 14.158 17.181 19.257

115 2.724 3.286 3.927 4.711 5.550 6.462 7.559 8.710 9.933 11.329 12.648 14.362 17.411 19.514

120 2.773 3.343 3.992 4.788 5.638 6.562 7.674 8.842 10.080 11.496 12.828 14.567 17.641 19.771

125 2.823 3.400 4.056 4.865 5.725 6.663 7.790 8.974 10.228 11.664 13.009 14.771 17.871 20.028

130 2.872 3.457 4.121 4.942 5.812 6.763 7.906 9.106 10.375 11.831 13.189 14.975 18.101 20.286

135 2.921 3.514 4.186 5.019 5.900 6.863 8.021 9.237 10.523 11.998 13.370 15.180 18.331 20.543

140 2.970 3.571 4.250 5.096 5.987 6.963 8.137 9.369 10.670 12.166 13.550 15.384 18.561 20.800

145 3.020 3.628 4.315 5.173 6.075 7.063 8.252 9.501 10.818 12.333 13.730 15.589 18.791 21.057

150 3.069 3.685 4.380 5.250 6.162 7.163 8.368 9.633 10.965 12.504 13.911 15.793 19.021 21.314

155 3.118 3.741 4.444 5.327 6.249 7.263 8.484 9.764 11.113 12.668 14.091 15.998 19.251 21.571

160 3.168 3.798 4.509 5.404 6.337 7.363 8.599 9.896 11.260 12.835 14.271 16.202 19.481 21.828

165 3.217 3.855 4.573 5.481 6.424 7463 8.715 10.028 11.408 13.003 14.452 16.407 19.711 22.086

170 3.266 3.912 4.638 5.558 6.512 7.563 8.830 10.160 11.555 13.170 14.632 16.611 19.941 22.343

175 3.316 3.969 4.703 5.635 6.599 7.664 8.946 10.291 11.703 13.337 14.812 16.815 20.171 22.600

180 3.365 4.026 4.767 5.712 6.686 7.764 9.062 10.423 11.850 13.505 14.993 17.020 20.401 22.857

185 3.414 4.083 4.832 5.789 6.774 7.864 9.177 10.555 11.998 13.672 15.173 17.224 20.631 23.114

190 3.463 4.140 4.897 5.866 6.861 7.964 9.293 10.687 12.145 13.839 15.353 17.429 20.861 23.371

195 3.513 4.197 4.961 5.943 6.949 8.064 9.408 10.818 12.293 14.007 15.534 17.633 21.091 23.628

200 3.562 4.254 5.026 6.020 7.036 8.164 9.524 10.950 12.440 14.174 15.714 17.838 21.321 23.886

205 3.611 4.311 5.091 6.097 7.123 8.264 9.640 11.082 12.588 14.341 15.895 18.042 21.551 24.143

210 3.661 4.368 5.155 6.174 7.211 8.364 9.755 11.214 12.735 14.509 16.075 18.246 21.781 24.400

215 3.710 4.425 5.220 6.251 7.298 8.464 9.871 11.345 12.883 14.676 16.255 18.451 22.012 24.657

220 3.759 4.482 5.285 6.328 7.386 8.564 9.986 11.477 13.030 14.843 16.436 18.655 22.242 24.914

225 3.809 4.539 5.349 6.405 7.473 8.665 10.102 11.609 13.178 15.011 16.616 18.860 22.472 25.171

230 3.858 4.596 5.414 6.482 7.560 8.765 10.218 11.741 13.325 15.178 16.796 19.064 22.702 25.428

235 3.907 4.653 5.479 6.559 7.648 8.865 10.333 11.872 13.473 15.345 16.977 19.269 22.932 25.686

240 3.956 4.710 5.543 6.636 7.735 8.965 10.449 12.004 13.620 15.513 17.157 19.473 23.162 25.943

245 4.006 4.767 5.608 6.713 7.823 9.065 10.564 12.136 13.768 15.680 17.337 19.678 23.392 26.200

250 4.055 4.824 5.673 6.790 7.910 9.165 10.680 12.268 13.915 15.848 17.518 19.882 23.622 26.457

255 4.104 4.880 5.737 6.867 7.997 9.265 10.796 12.399 14.063 16.015 17.698 20.086 23.852 26.714

260 4.154 4.937 5.802 6.944 8.085 9.365 10.911 12.531 14.210 16.182 17.878 20.291 24.082 26.971

265 4.203 4.994 5.866 7.021 8.172 9.465 11.027 12.663 14.358 16.350 18.059 20.495 24.312 27.228

270 4.252 5.051 5.931 7.098 8.260 9.565 11.142 12.795 14.505 16.517 18.239 20.700 24.542 27.485

275 4.302 5.108 5.996 7.175 8.347 9.666 11.258 12.926 14.653 16.684 18.419 20.904 24.772 27.746

d

l

ACC/DIN 976 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 33: Esparragos y Tornillos Catalogo Tecnico

32DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d l

PESO (Kg) POR 1 PIEZA / WEIGHT (Kg) PER 1 PIECEM42 M45 M48 M52 M56 M60 M64 M68 M72 M76 M80 M85 M90 M95

280 4.351 5.165 6.060 7.252 8.434 9.766 11.374 13.058 14.800 16.852 18.600 21.109 25.002 28.000

285 4.400 5.222 6.125 7.329 8.522 9.866 11.489 13.190 14.948 17.019 18.780 21.313 25.232 28.257

290 4.449 5.279 6.190 7.406 8.609 9.966 11.605 13.322 15.095 17.186 18.961 21.518 25.462 28.514

295 4.499 5.336 6.254 7.483 8.697 10.066 11.720 13.453 15.243 17.354 19.141 21.722 25.692 28.771

300 4.548 5.393 6.319 7.560 8.784 10.166 11.836 13.585 15.390 17.521 19.321 21.926 25.922 29.028

305 4.597 5.450 6.384 7.637 8.871 10.266 11.952 13.717 15.538 17.688 19.502 22.131 26.152 29.286

310 4.647 5.507 6.448 7.714 8.959 10.366 12.067 13.849 15.685 17.856 19.682 22.335 26.382 29.543

315 4.696 5.564 6.513 7.791 9.046 10.466 12.183 13.980 15.833 18.023 19.862 22.540 26.612 29.800

320 4.745 5.621 6.578 7.868 9.134 10.566 12.298 14.112 15.980 18.190 20.043 22.744 26.842 30.057

325 4.795 5.678 6.642 7.945 9.221 10.667 12.414 14.244 16.128 18.358 20.223 22.949 27.072 30.314

330 4.844 5.735 6.707 8.022 9.308 10.767 12.530 14.376 16.275 18.525 20.403 23.153 27.302 30.571

335 4.893 5.792 6.772 8.099 9.396 10.867 12.645 14.502 16.423 18.692 20.584 23.357 27.532 30.828

340 4.942 5.849 6.836 8.176 9.483 10.967 12.761 14.639 16.570 18.860 20.764 23.562 27.762 31.086

345 4.992 5.906 6.901 8.253 9.571 11.067 12.876 14.771 16.718 19.027 20.944 23.766 27.992 31.343

350 5.041 5.963 6.966 8.330 9.658 11.167 12.992 14.903 16.865 19.195 21.125 23.971 28.222 31.600

355 5.090 6.019 7.030 8.407 9.745 11.267 13.108 15.034 17.013 19.362 21.305 24.175 28.453 31.857

360 5.140 6.076 7.095 8.484 9.833 11.367 13.223 15.166 17.160 19.529 21.485 24.380 28.683 32.114

365 5.189 6.133 7.159 8.561 9.920 11.467 13.339 15.298 17.308 19.697 21.666 24.584 28.913 32.371

370 5.238 6.190 7.224 8.638 10.008 11.567 13.454 15.430 17.455 19.864 21.846 24.789 29.143 32.628

375 5.288 6.247 7.289 8.715 10.095 11.668 13.570 15.561 17.603 20.031 22.027 24.993 29.373 32.885

380 5.337 6.304 7.353 8.792 10.182 11.768 13.686 15.693 17.750 20.199 22.207 25.197 29.603 33.143

385 5.386 6.361 7.418 8.869 10.270 11.868 13.801 15.825 17.898 20.366 22.387 25.402 29.833 33.400

390 5.435 6.418 7.483 8.946 10.357 11.968 13.917 15 957 18.045 20.533 22.568 25.606 30.063 33.657

395 5.485 6.475 7.547 9.023 10.445 12.068 14.032 16.088 18.193 20.701 22.748 25.811 30.293 33.914

400 5.534 6.532 7.612 9.100 10.532 12.168 14.148 16.220 18.340 20.868 22.928 26.015 30.523 34.171

405 5.583 6.589 7.677 9.177 10.619 12.268 14.264 16.352 18.488 21.035 23.109 26.220 30.753 34.428

410 5.633 6.646 7.741 9.254 10.707 12.368 14.379 16.484 18.635 21.203 23.289 26.424 30.983 34.685

415 5.682 6.703 7.806 9.331 10.794 12.468 14.495 16.615 18.783 21.370 23.469 26.629 31.213 34.943

420 5.731 6.760 7.871 9.408 10.882 12.568 14.610 16.747 18.930 21.537 23.650 26.833 31.443 35.200

425 5.781 6.817 7.935 9.485 10.969 12.669 14.726 16.879 19.078 21.705 23.830 27.037 31.673 35.457

430 5.830 6.874 8.000 9.562 11.056 12.769 14.842 17.011 19.225 21.872 24.010 27.242 31.903 35.714

435 5.879 6.931 8.065 9.639 11.144 12.869 14.957 17.142 19.373 22.039 24.191 27.446 32.133 35.971

440 5.928 6.988 8.129 9.716 11.231 12.969 15.073 17.274 19.520 22.207 24.371 27.651 32.363 36.228

445 5.978 7.045 8.194 9.793 11.319 13.069 15.188 17.406 19.668 22.374 24.551 27.855 32.593 36.485

450 6.027 7.102 8.259 9.870 11.406 13.169 15.304 17.538 19.815 22.542 24.732 28.060 32.823 36.743

455 6.076 7.158 8.323 9.947 11.493 13.269 15.420 17.669 19.963 22.709 24.912 28.264 33.053 37.000

460 6.126 7.215 8.388 10.024 11.581 13.369 15.535 17.801 20.110 22.876 25.093 28.468 33.283 37.257

465 6.175 7.272 8.452 10.101 11.668 13.469 15.651 17.933 20.258 23.044 25.273 28.673 33.513 37.514

470 6.224 7.329 8.517 10.178 11.756 13.569 15.766 18.065 20.405 23.211 25.453 28.877 33.743 37.771

475 6.274 7.386 8.582 10.255 11.843 13.670 15.882 18.196 20.553 23.378 25.634 29.082 33.973 38.028

480 6.323 7.443 8.646 10.332 11.930 13.770 15.998 18.328 20.700 23.546 25.814 29.286 34.203 38.285

485 6.372 7.500 8.711 10.409 12.018 13.870 16.113 18.460 20.848 23.713 25.994 29.491 34.433 38.543

490 6.421 7.557 8.776 10.486 12.105 13.970 16.229 18.592 20.995 23.880 26.175 29.695 34.663 38.800

495 6.471 7.614 8.840 10.563 12.193 14.070 16.344 18.723 21.143 24.048 26.355 29.900 34.893 39.057

500 6.520 7.671 8.905 10.640 12.280 14.170 16.460 18.855 21.290 24.215 26.535 30.104 35.124 39.314

d

l

ACC/DIN 976 - Totalmente roscados con dos tuercas / Totally threaded with 2 heavy exagonal nuts

PESOS DE ESPÁRRAGOSTABLE OF WEIGHT STUDBOLTS

Page 34: Esparragos y Tornillos Catalogo Tecnico

33DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. With reduced Shank

ESPÁRRAGOS DE DILATACIÓN - DIN 2510BOLTED CONNECTIONS - DIN 2510

z1b1

d 1 d 2 d 3

l1

z1b1 z2

2 Faces A/F

b2b2

b2b2z3

d 7

l1

b3 b3

b3 b3z4

d 7

l1

type L

type K

type KU

type Z

type ZU

Page 35: Esparragos y Tornillos Catalogo Tecnico

34DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. With reduced Shank - Types L, K, KU, Z, ZU

thread d1 acc. To DIN 2510 sec.2

M12

M16

M20

M24

M27

M30

M33

M36

M39

M42

M45

M48

M52

M56

d2 8,5 12 15 18 20,5 23 25,5 27,5 30,5 32,5 35,5 37,5 41 44

d3 8 12 14 14 18 18 25 25 28 28 32 32 36 40

d7 8 12 13 16 18 21 24 26 30 32 34 37 40 45

b1 20 23 28 32 35 39 42 45 48 52 55 58 62

b2 13 16 20 24 27 30 33 36 39 42 45 48 52 56

b3 27 31 36 42 47 50 53 57 60 64 66 70 74 79

A/F 7 10 11 11 13 13 22 22 24 24 27 27 30 32

Z1 max. 1,75 2 2,5 3 3 3,5 3,5 4 4 4,5 4,5 5 5 5,5

Z2 4 5 6 6 6 6 9 9 10 10 11 11 12 13

Z3 11 14 16 17 19 19 21 23 23 24 25 26 26 28

Z4 7 8 9 8 10 12 14 14 14 15 15 19 18 19

Centr. A 1,6 A 2,5

thread d1 acc. To DIN 2510 sec.2

M64

M72

M80

M90

M 100

M 110

M 120

M 130

M 140

M 150

M 160

M 170

M 180

d2 51 58,5 66 75 84 92,5 102 106 118 127 136 145 154

d3 42 50 50 50 50 50 50 50 65 65 65 65 65

d7 52 56 63 74 86 97 105

b1

b2 64 72 80 90 100 110 120 125 140 150 160 170 180

b3 88 95 103 112 122 132 142

A/F 36 41 41 41 41 41 41 41 55 55 55 55 55

Z1 max. 6 6 6 6 6 6 6 8 8 8 8 8 8

Z2 14 15 15 15 15 15 15 15 18 18 18 18 18

Z3 28 28 28 28 28 28 30

Z4 20 20 19 20 19 19 20

Centr. A 4 A 6,3

ESPÁRRAGOS DE DILATACIÓN - DIN 2510BOLTED CONNECTIONS - DIN 2510

Page 36: Esparragos y Tornillos Catalogo Tecnico

35DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. Según normas DIN 2510 Forma NF / DIN 2510 shape NF

TUERCAS PARA ESPÁRRAGOS DE DILATACIÓNNUTS FOR BOLTED CONNECTIONS

Size d se min.

d1 m tmg m

M 12 22 23,91 24,49 21 12 2

M 16 27 29,56 30,14 26 16 2

M 20 32 35,03 35,72 31 20 2

M 24 36 39,55 39,98 35 24 3

M 27 41 45,2 45,63 40 27 3

M 30 46 50,85 51,28 45 30 3

M 33 50 55,37 55,8 49 33 3

M 36 55 60,79 61,31 53,5 36 3

M 39 60 66,44 66,96 58,5 39 3

M 42 65 72,09 72,61 63,5 42 3

M 45 70 77,74 78,26 68,5 45 3

M 48 75 83,39 83,91 73,5 48 4

M 52 80 89,04 89,56 78,5 52 4

M 56 85 94,47 95,07 83,5 56 4

M 64 95 105,77 106,37 93,5 64 4

M 72 105 117,07 117,67 103,5 72 4

M 80 115 128,37 129,34 113,5 80 4

M 90 130 145,09 145,77 128 90 4

M 100 145 162,04 162,74 143 100 5

e

120º

70º

tms

30º

dld

Page 37: Esparragos y Tornillos Catalogo Tecnico

36DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. Peso de 100 piezas kg. / weight for 100 pieces.

TABLA DE PESOS PARA ESPÁRRAGOS Y TUERCASSTUD BOLTS AND NUTS DIN 2510 L/NF

M12 M16 M20 M24 M27 M30 M33 M36 M39 M42 M45 M48 M52

50 8,887

55 9,11

60 9,332 19,2

65 9,552 19,64

70 9,777 20,08 33,61

75 10 20,52 34,3

80 10,222 20,95 34,99 50,48

85 10,442 21,38 35,65 51,48

90 10,664 21,82 36,34 52,48 74,16

95 10,89 22,3 37,03 53,48 75,46

100 11,112 22,75 37,77 54,48 76,75 102,06

110 11,562 23,64 39,16 56,48 79,35 105,33 134,57

120 12,002 24,53 40,55 58,48 81,95 108,6 138,58 176,6

130 12,442 25,41 41,94 60,48 84,55 111,87 142,58 181,2 222,1

140 12,892 26,3 43,33 62,48 87,15 115,14 146,59 185,9 228

150 13,342 27,19 44,72 64,48 89,75 118,42 150,6 190,5 234 271 355

160 13,782 28,07 46,11 66,48 92,35 121,69 154,61 195,2 240 278 363

170 14,222 28,97 47,49 70,48 94,95 124,96 158,62 199,9 246 284 370 448

180 14,692 29,85 48,88 72,48 97,55 128,93 162,63 204,5 251,9 290 378 457 542

190 30,74 50,27 74,48 100,15 131,5 166,64 209,2 257,9 297 386 465 553

200 31,63 51,66 76,48 102,73 134,78 170,65 213,8 263,9 303 394 474 563

210 53,05 7848 105,33 138,05 174,66 218,5 269,8 310 401 483 573

220 54,45 80,48 107,93 141,32 178,67 223,2 275,8 316 409 491 584

230 55,83 82,48 110,53 144,59 182,68 227,8 281,7 323 417 500 594

240 57,22 84,48 113,13 147,86 186,68 232,5 287,7 329 425 509 604

250 58,61 86,48 115,73 151,14 190,69 237,2 293,7 336 433 517 615

260 59,99 88,48 118,33 154,41 194,7 241,8 299,6 342 440 526 625

270 61,38 90,48 120,93 157,68 198,71 246,5 305,6 349 448 535 635

280 62,78 92,48 123,53 160,95 202,72 251,1 311,5 355 456 543 646

290 64,17 94,48 126,13 164,22 206,73 255,8 317,5 362 464 552 656

300 65,56 96,48 128,73 167,49 210,74 260,5 323,4 368 471 561 666

310 66,95 98,48 131,33 170,77 214,75 265,1 329,4 374 479 569 677

320 68,33 100,48 133,93 174,04 218,76 269,8 335,3 381 487 578 687

330 102,48 136,53 177,31 222,76 274,4 341,3 388 495 587 697

340 139,13 180,51 226,77 279,1 347,3 394 502 595 708

350 141,73 183,85 230,78 283,8 352,2 401 510 604 718

360 144,33 187,12 234,79 288,4 359,2 408 518 613 728

370 190,39 238,8 293,1 365,1 415 526 621 739

380 193,66 252,81 297,8 371,1 422 534 630 749

weight for 100

nuts3,10 5,20 8,60 12,40 18,10 26,00 33,00 42,50 56,00 70,50 90,00 112,00 134,00

Page 38: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

37DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

TornillosBolts

ANSI/DIN

Page 39: Esparragos y Tornillos Catalogo Tecnico

38DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ANSI 18.2.1SERIE NORMAL

TORNILLOS HEXAGONALES / HEXAGONAL BOLTS

nominal size E F G H R X

L≤6“ L>6”

1/4 0,260 7/16 0,438 0,425 0,505 0,484 11/64 0,188 0,150 0,03 0,01 0,750 1,000

5/16 0,324 1/2 0,500 0,484 0,577 0,552 7/32 0,235 0,195 0,03 0,01 0,875 1,125

3/8 0,388 9/16 0,562 0,544 0,650 0,620 1/4 0,268 0,226 0,03 0,01 1,000 1,250

7/16 0,452 5/8 0625 0,603 0,722 0,687 19/64 0,316 0,272 0,03 0,01 1,125 1,375

1/2 0,515 3/4 0,750 0,725 0,866 0,826 11/32 0,364 0,302 0,03 0,01 1,250 1,500

5/8 0,642 15/16 0,938 0,906 1,083 1,033 27/64 0,444 0,378 0,06 0,02 1,500 1,750

3/4 0,768 1-1/8 1,125 1,088 1,299 1,240 1/2 0,524 0,455 0,06 0,02 1,750 2,000

7/8 0,895 1-5/16 1,312 1,269 1,516 1,447 57/64 0,604 0,531 0,06 0,02 2,000 2,250

1 1,022 1-1/2 1,500 1,450 1,732 1,653 43/64 0,700 0,591 0,09 0,03 2,250 2,500

1-1/8 1,149 1-11/16 1,688 1,631 1,949 1,859 3/4 0,780 0,658 0,09 0,03 2,500 2,750

1-1/4 1,277 1-7/8 1,875 1,812 2,465 2,066 27/32 0,876 0,749 0,09 0,03 2,750 3,000

1-3/8 1 404 2-1/16 2 062 1,994 2,384 2,273 29/32 0,940 0,810 0,09 0,03 3,000 3,250

1-1/2 1,531 2-1/4 2,250 2,175 2,598 2,480 1 1,036 0,902 0,09 0,03 3,250 3,500

1-3/4 1,785 2-5/8 2,625 2,538 3,031 2,893 1-5/32 1,196 1,054 0,12 0,04 3,750 4,000

2 2,039 3 3,000 2,900 3,464 3,306 1-11/32 1,388 1,175 0,12 0,04 4,250 4,500

2-1/4 2,305 3-3/8 3,375 3,262 3,897 3,719 1-1/2 1,548 1,327 0,19 0,06 4,750 5,000

2-1/2 2,559 3-3/4 3,750 3,625 4,330 4,133 1-21/32 1,708 1,479 0,19 0,06 5,250 5,500

2-3/4 2,827 4-1/8 4,125 3,988 4,763 4,546 1-13/16 1,869 1,632 0,19 0,06 5,750 6,000

3 3,081 4-1/2 4,500 4,350 5,196 4,959 2 2,060 1,815 0,19 0,06 6,250 6,500

3-1/4 3 335 4-7/8 4,875 4,712 5,629 5,372 2-3/16 2,251 1,936 0,19 0,06 6,750 7,000

3-1/2 3,589 5-1/4 5,250 5,075 6,062 5,786 2-5/16 2,380 2,057 0,19 0,06 7,250 7,500

3-3/4 3,858 5-5/8 5,625 5,437 6,495 6,198 2-1/2 2,572 2,241 0,19 0,06 7,750 8,000

4 4,111 6 6,000 5,800 6,928 6,612 2-11/16 2,764 2,424 0,19 0,06 8,250 8,500

LG

R

E

X

H

L+0º-15º+0º

G

F

Page 40: Esparragos y Tornillos Catalogo Tecnico

39DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ANSI 18.2.1SERIE PESADA

TORNILLOS HEXAGONALES / HEXAGONAL BOLTS

nominal size E F G H R X

L≤6“ L>6”

1/2 0.515 7/8 0,875 0,850 1,010 0,969 11/32 0,364 0,320 0,03 0,01 1,250 1,500

5/8 0,642 1-1/16 1,062 1,031 1,227 1,175 27/64 0,444 0,378 0,06 0,02 1,500 1,750

3/4 0,768 1-1/4 1,250 1,212 1,443 1,383 1/2 0,524 0,455 0,06 0,02 1,750 2,000

7/8 0,895 1-7/16 1,438 1,394 1,660 1,589 37/64 0,604 0,531 0,06 0,02 2,000 2,250

1 1,022 1-5/8 1,625 1,575 1,876 1,796 43/64 0,700 0,591 0,09 0,03 2,250 2,500

1-1/8 1,149 1-13/16 1,812 1,756 2,093 2,002 3/4 0,780 0,658 0,09 0,03 2,500 2,750

1-1/4 1,277 2 2,000 1,938 2,309 2,209 27/32 0,876 0,749 0,09 0,03 2,750 3,000

1-3/8 1,404 2-3/16 2,188 2,119 2,526 2,416 29/32 0,940 0,810 0,09 0,03 3,000 3,250

1-1/2 1,531 2-3/8 2,375 2,300 2.742 2,622 1 1,036 0,902 0,09 0,03 3,250 3,500

1-3/4 1,785 2-3/4 2,750 2,662 3,175 3,035 1-5/32 1,196 1,054 0,12 0,04 3,750 4,000

2 2,039 3-1/8 3,125 3,025 3,608 3,449 1-11/32 1,388 1,175 0,12 0,04 4,250 4,500

2-1/4 2,305 3-1/2 3,500 3,388 4,041 3,862 1-1/2 1,548 1,327 0,19 0,06 4,750 5,000

2-1/2 2,559 3-7/8 3,875 3,750 4,474 4,275 1-21/32 1,708 1,479 0,19 0,06 5,250 5,500

2-3/4 2,827 4-1/4 4,250 4,112 4,907 4,688 1-13/16 1,869 1,632 0,19 0,06 5,750 6,000

3 3,081 4-5/8 4,625 4,475 5,340 5,102 2 2,060 1,815 0,19 0,06 6,250 6,500

LG

R

E

X

H

L+0º-15º+0º

G

F

Page 41: Esparragos y Tornillos Catalogo Tecnico

40DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d M1,6 M2 M2,5 M3 (M3,5) M4 M5 M6

P 0,35 0,4 0,45 0,5 0,6 0,7 0,8 1

b dimension

1) 9 10 11 12 13 14 16 18

2) 22 24

3)

dsmax. 1,6 2 2,5 3 3,5 4 5 6

min. 1,46 1,86 2,36 2,86 3,32 3,82 4,82 5,82

e min. typeA 3,48 4,38 5,45 6,01 6,58 7,66 8,79 11,05

B 8,63 10,89

k

dimension 1,1 1,4 1,7 2 2,4 2,8 3,5 4

type

min. 0,98 1,28 1,58 1,88 2,28 2,68 3,35 3,85

max. 1,22 1,52 1,82 2,12 2,52 2,92 3,65 4,15

min. 3,26 3,76

max. 3,74 4,24

r min. 0,1 0,1 0,1 0,1 0,1 0,2 0,2 0,25

s

max. = dimension 3,2 4 5 5,5 6 7 8 10

typeA 3,08 3,88 4,82 5,32 5,82 6,78 7.78 9,78

B 7,64 9,64

Con vástago DIN 931 ISO 4014Partially threaded

Tornillo HexagonalHexagonal BolT

ILongitud de eje ls y lg / Shaft lengths ls and lg

Type

dimen-sion

A B ls lg ls lg ls lg ls lg ls lg ls lg ls lg ls lg

min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

12 11,65 12,35 1,2 3

(14) 13,65 14,35 3,2 5

16 15,65 16,35 5,2 7 4 6 3 5

(16) 17,65 18,35 6 8 5 7

20 19,58 20,42 8 10 7 9 5,5 8

(22) 21,58 22,42 9 11 7,5 10

25 24,58 25,42 12 14 10,5 13 9 12 7,5 11 5 9

(28) 27.58 28,42 13,5 16 12 15 10,5 14 8 12

30 29,58 30,42 15,5 18 14 17 12,5 16 10 14 7 12

35 34,5 35,5 33,75 36,25 19 22 17,5 21 15 19 12 17

40 39,5 40,5 38,75 41,25 22,5 26 20 24 17 22

45 44,5 45,5 43,75 46,25 25 29 22 27

50 49,5 50,5 48,75 51,25 30 34 27 32

55 54,4 55,6 53,5 56,5 32 37

60 59,4 60,6 58,5 61,5 37 42

1) For I <125.2) For l 125 ÷ 200.3) For I >200.

s

ed

b

k l

da ds

LsLg

Page 42: Esparragos y Tornillos Catalogo Tecnico

41DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d (M7) M8 M10 M12 (M14) M16 (M18) M20

P 1 1,25 1,5 1,75 2 2 2,5 2,5

b

nominal size

1) 20 22 26 30 34 38 42 46

2) 26 28 32 36 40 44 48 52

3) − − 45 49 53 57 61 65

d2

max. 7 8 10 12 14 16 18 20

min. 6,78 7,78 9,78 11,73 13,73 15,73 17,73 19,67

e mín. type A 12,12 14,38 17,77 18,90 20,03 21,1 23,35 24,49 29,75 30,14 22,53

B 11,94 14,20 17,59 18,72 19,85 20,88 22,78 23,91 27,17 29,56 32,95

k

dimension 5,3 6,4 7,5 8,8 10 11,5 12,5

type

Amin. 4,65 5,15 6,22 7,32 8,62 9,82 11,28 12,28

max. 4,92 5,45 6,58 7,66 8,98 10,18 11,72 12,72

Bmin. 4,56 5,06 6,11 7,21 8,51 9,71 11,15 12,15

max. 5,04 5,54 6,69 7,79 9,09 10,29 11,85 12,85

r min. 0,25 0,4 0,4 0,6 0,6 0,6 0,6 0,8

s mín

max. = dimension 11 13 16 17 18 19 21 22 24 27 30

typeA 10,73 12,73 15,73 16,73 17,73 18,67 20,67 21,67 23,67 26,67 29,57

B 10,57 12,57 15,57 16,57 17,57 18,48 20,16 21,16 23,61 26,16 29,16

IType Longitud de eje ls y lg / Shaft lengths ls and lg

di-men-sion

A B ls lg ls lg ls lg ls lg ls lg ls lg ls lg ls lgmin. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

30 29,58 30,42 − − 5 10

35 34,5 35,5 33,75 36,25 10 15 6,75 13

40 39,5 40,5 38,75 41,25 15 20 11,75 18 5,5 14

45 44,5 45,5 43,75 46,25 20 25 16,75 23 11,5 19 6,25 15

50 49,5 50,5 48,75 51,25 25 30 21,75 28 16,5 24 11,25 20 6 16 7 17

55 54,5 55,6 53,5 56,5 30 35 26,75 33 21,5 29 16,25 25 11 21 12 22

60 59,4 60,6 58,5 61,5 35 40 31,75 38 26,5 34 21,25 30 16 26 17 27 10,5

65 64,4 65,6 63,5 66,5 40 45 36,75 43 31,5 39 26,25 35 21 31 22 32 15,5 23 6,5 19

70 69,4 70,6 68,5 71,5 45 50 41,75 48 36,5 44 31,25 40 26 36 27 37 20,5 28 11,5 24

(75) 74,4 75,8 73,5 76,5 46,75 53 41,5 49 36,25 45 31 41 32 42 25,5 33 16,5 29

80 79,4 80,6 78,5 81,5 51,75 58 46,5 54 41,25 50 36 46 37 47 30,5 38 21,5 34

(85) 84,3 85,7 83,25 86,75 51,5 59 46,25 55 41 51 42 52 35,5 43 26,5 39

90 89,3 90,7 88,25 91,75 56,5 64 51,25 60 46 56 47 57 40,5 48 31,5 44

(95) 94,3 95,7 93,25 96,75 61,5 69 56,25 65 51 61 52 62 45,5 53 36,5 49

100 99,3 100,7 98,25 101,75 66,5 74 61,25 70 56 66 62 72 55,5 58 41,5 54

110 109,3 110,7 108,25 111,75 71,25 80 66 76 72 82 65,5 68 51,6 64

120 119,3 120,7 118,25 121,75 81,25 90 76 86 76 86 69,5 78 61,5 74

130 129,2 130,8 128 132 80 90 86 96 79,5 82 65,5 78

140 139,2 140,8 138 142 90 100 96 106 89,5 92 75,7 88

150 149,2 150,8 148 152 106 116 99,5 102 85,8 98

160 159,2 160,8 158 162 109,5 112 95,5 108

(170) 169,2 170,8 168 172 119,5 112 105,5 118

180 179,2 180,8 178 182 132 115,5 128

(190) 189,08 190,92 187,7 192,8 125,5 138

200 199,08 200,92 197,7 202,3 135,5 148

1) For I <125.2) For l 125 ÷ 200.3) For I >200.

s

ed

b

k l

da ds

LsLgCon vástago DIN 931 ISO 4014

Partially threaded

Tornillo HexagonalHexagonal BolT

Page 43: Esparragos y Tornillos Catalogo Tecnico

42DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d (M22) M24 M27 M30 (M33) M36 (M39)

P 2,5 3 3 3,5 3,5 4 4

b

1) 50 54 60 66 72 78 84

dimension 2) 56 80 68 72 78 84 90

3) 69 73 79 85 91 97 103

d2

max. 22 24 27 30 33 36 39

min. 21,67 23,87 28,67 29,67 32,81 35,81 38,81

e mín. typeA 35,72 37,72 39,98

45,2 50,85 55,37 60,79 66,44B 35,03 37,29 39,55

k

dimension 14 15 17 18,7 21 22,5 25

type

Amin. 13,78 14,78

max. 14,22 15,22

Bmin. 13,65 14,65 16,65 18,28 20,58 22,08 24,58

max. 14,35 15,35 17,35 19,12 21,42 22,92 25,42

r min. 0,8 0,8 1 1 1 1 1

s min

max. = dimension 32 34 36 41 46 50 55 60

typeA 31,61 33,38 35,38

40 45 49 53,8 58,8 B 31 33 35

1) For I <125.2) For l 125 ÷ 200.3) For I >200.

l Type Longitud de eje ls y lg / Shaft lengths ls and lg

di-men-sion

A B ls lg ls lg ls lg ls lg ls lg ls lg ls lgmin. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

70 69,4 70.6 68,5 71,5 7,5 20

(75) 74,4 75.6 73,5 76,5 12,5 25

80 79,4 80,6 78,5 81,5 17,5 30 11 26

(85) 84,3 85,7 83,25 86,75 22.5 35 16 31

90 89,3 90,7 88,25 91,75 27,5 40 21 38 15 30 8,5 24

(95) 94,5 95,7 93,25 96,75 32,5 45 26 41 20 35 11,5 29

100 99,3 100,7 98,25 101,8 37,5 50 31 48 25 40 16,5 34 10,5 28

110 109,3 110,7 108,25 111,8 47,5 80 41 58 35 50 28,5 44 20,5 38 12 32

120 119,3 120,7 118,3 121,8 57,5 70 51 86 45 80 36,5 54 30,5 48 22 42 16 36

130 129,2 130,8 128 132 61,5 74 55 70 49 64 40,5 58 34,5 52 28 46 20 40

140 139,2 140,8 138 142 71,5 84 85 80 59 74 50,5 68 44,5 82 36 58 30 50

150 149,2 150,8 148 152 81,5 94 75 90 69 84 60,5 78 54,5 72 48 66 40 60

160 159,2 160,8 158 162 91,5 104 85 100 79 94 70,5 88 84,5 82 56 78 50 70

(170) 169,2 170,8 188 172 101,5 114 95 110 89 104 80,5 98 74,5 92 66 88 60 80

180 179,2 180,8 178 182 111,5 124 105 120 99 114 90,5 108 84,5 102 76 96 70 90

(190) 189,08 190,9 187,7 192,3 121,5 134 115 130 109 124 100,5 118 94,5 112 88 106 80 100

200 199,1 200,92 197,7 202,3 131,5 144 125 140 119 134 110,5 128 104,5 122 96 116 90 110

220 219,08 220,92 217,7 222,3 138,5 151 132 147 128 141 117,5 135 111,5 129 103 123 97 117

240 239,1 240,92 337,7 242,3 152 167 146 161 137,5 155 131,5 149 123 143 117 137

280 259 261,1 257,4 262,6 166 181 157,7 175 151,5 169 143 163 137 157

280 279 281,05 277,4 282,6 177,5 195 171,5 189 183 183 157 177

300 298,95 301,5 297,4 302,6 197,5 215 191,5 209 183 203 177 197

s

ed

b

k l

da ds

LsLgCon vástago DIN 931 ISO 4014

Partially threaded

Tornillo HexagonalHexagonal BolT

Page 44: Esparragos y Tornillos Catalogo Tecnico

43DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d M42 (M45) M48 ( M52) M56 (M60) M64 (M68) M72X6 P 4,5 4,5 5 5 5,5 6 6 6

b dimension

1) 90 96 102 − − − − − −

2) 96 102 108 116 124 132 140 148 156

3) 109 115 121 129 137 145 153 161 169

dS max. 42 45 48 52 56 60 64 68 72

e min. 72,02 76,95 82,6 88,25 93,56 99,21 104,86 110,51 116,16

k

dimension 26 28 30 33 35 38 40 43 45

min. 25,58 27,58 29,58 32,5 34,5 37,5 39,5 42,5 44,5

max. 26.42 28,42 30,42 33,5 35,5 38,5 40,5 43,5 45,5

r min. 1,2 1,2 1,6 1,6 2 2 2 2 2

smax. = dimension 65 70 75 80 85 90 95 100 105

min. 63,6 68,1 73,1 78,1 82,8 87,8 92,8 97,8 102,8

I Longitud de eje ls y lg / Shaft lengths ls and lg

dimen-sion min. max.

ls lg ls lg ls lg ls lg ls lg ls lg ls lg ls lg ls lgmin. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

130 128 132 11,5 34 5,5 28

140 138 142 21,5 44 15,5 38 7 32

150 148 152 31,5 54 25,5 48 17 42 9 34

160 158 162 41,5 64 35,5 58 27 52 27 52 27 52 19 44 8,5 38

170 168 172 51,5 74 45,5 68 37 62 29 54 18,5 46 10,5 38

180 178 182 61,5 84 55,5 78 47 72 39 64 28,5 56 20,5 48 10 40

(190) 187,7 192.3 71,5 94 65,6 88 57 82 49 74 38,5 66 30,5 58 20 50 12 42

200 197,7 202.3 81,5 104 75,7 98 67 92 59 84 48,5 76 40,5 68 30 60 22 52 14 44

220 217,7 222,3 88,5 111 82,5 105 74 99 66 91 55,9 83 47,5 75 37 67 29 59 21 51

240 237,7 242,3 108,5 131 102,5 125 94 119 86 111 75,5 103 67,5 95 57 87 49 79 41 71

260 257,4 262.6 128,5 151 122,5 145 114 139 106 131 95,5 123 87,5 115 77 107 69 99 61 91

280 277,4 282,6 148,5 171 142,5 165 134 159 126 151 115,5 143 7,5 135 97 127 89 119 81 111

300 297,4 302,8 168,5 191 162,5 185 154 179 146 171 135,5 163 27,5 155 117 147 109 139 101 131

320 317,15 322,85 174 199 166 191 155,5 183 47,5 175 137 167 129 159 121 151

340 337,15 342,85 194 219 186 211 175,5 203 167,5 195 157 187 149 179 141 171

360 357,15 362,85 195,5 223 187,5 215 177 207 169 199 161 191

380 377,15 382,85 189 219 181 211

400 397,15 402,85 201 231

1) For I <125.2) For l 125 ÷ 200.3) For I >200.

s

ed

b

k l

da ds

LsLgCon vástago DIN 931 ISO 4014

Partially threaded

Tornillo HexagonalHexagonal BolT

Page 45: Esparragos y Tornillos Catalogo Tecnico

44DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d (M76 x 6) M80 x 6 M90 x 6 M100 x 6 M110 x 6 M125 x 6 M140 x 6 M160 x 6P 6 6 6 6 6 6 6 6

b

1) − − − − − − − −

dimension 2) 164 172 192 − − − − −

3) 177 185 205 225 245 275 305 345

d1

max. 76 88 90 100 110 125 140 160

min. 75,26 79,26 89,13 99,13 109,13 124 139 159

e min. 121,48 127,12 144,08 161,02 172,32 200,57 220,8 254,7

kdimension 48 50 57 63 69 79 88 100

min. 47,5 49,5 56,4 62,4 68,4 78,4 87,3 99,3

r max. 48,5 50,5 57,6 63,6 69,6 79,6 88,7 100,7

min. 2 2 2,5 2,5 2,5 2,5 2,5 2,5

smax. x dimension 110 115 130 145 155 180 200 2308

min. 107,5 117,5 127,5 142,5 152,5 177,5 195,4 225,4

I Longitud de eje ls y lg / Shaft lengths ls and lg

dimen-sion min. max.

ls lg ls lg ls lg ls lg ls lg ls lg ls lg ls lgmin. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.

220 217,7 222,3 13 43 5 35

240 237,7 242,3 33 63 25 55 5 35

260 257,4 262,6 53 83 45 75 25 55 5 35

280 277,4 282,6 73 103 65 95 45 75 25 55 5 35

300 297,4 302,6 93 123 85 115 65 95 45 75 25 55

320 317,15 322,85 113 143 105 135 85 115 65 95 45 75 15 45

340 337,15 342,85 133 163 125 155 105 135 85 115 65 95 35 65 5 35

360 357,15 362,85 153 183 145 175 125 155 105 135 85 115 55 85 25 55

380 377,15 382,85 173 203 165 195 145 175 125 155 105 135 75 105 45 75 5 35

400 397,15 402,85 193 223 185 215 165 195 145 175 125 155 95 125 65 95 25 55

420 416,85 423,15 213 243 205 235 185 215 165 195 145 175 115 145 85 115 45 75

440 436,85 443,15 225 255 205 235 185 215 165 195 135 165 105 135 65 95

460 456,85 463,15 245 275 225 255 205 235 185 215 155 185 125 155 85 115

480 476,85 483,15 245 275 225 255 205 235 175 205 145 175 105 135

500 496,85 503,15 265 295 245 275 225 255 195 225 165 195 125 155

1) For I <125.2) For l 125 ÷ 200.3) For I >200

s

ed

b

k l

da ds

LsLgCon vástago DIN 931 ISO 4014

Partially threaded

Tornillo HexagonalHexagonal BolT

Page 46: Esparragos y Tornillos Catalogo Tecnico

45DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.Con rosca hasta la cabeza DIN 933 ISO 4017Totally threaded

Thread d M1,6 M2 M2,5 M3 (M3,5) M4 M5 M6P 0,35 0,4 0,45 0,5 0,6 0,7 0,8 1

a max. 1,05 1,2 1,35 1,5 1,8 2,1 2,4 3

cmin. 0,1 0,1 0,1 0,15 0,15 0,15 0,15 0,15

max. 0,25 0,25 0,25 0,4 0,4 0,4 0,5 0,5

da max. 2 2,6 3,1 3,6 4,1 4,7 5,7 6,8

e min typeA 3,48 4,38 5,45 6,01 6,58 7,66 8,79 11,05

B 8,63 10,89

k type

dimension 1,1 1,4 1,7 2 2,4 2,8 3,5 4

Amin. 0,98 1,28 1,58 1,88 2,28 2,68 3,35 3,85

max. 1,22 1,52 1,82 2,12 2,52 2,92 3,65 4,15

Bmin. 3,26 3,76

max. 3,74 4,24

r min. 0,1 0,1 0,1 0,1 0,1 0,2 0,2 0,25

s

max. = dimension 3,2 4 5 5,5 6 7 8 10

min. typeA 3,08 3,88 4,82 5,32 5,62 6,78 7,78 9,78

B 7,64 9,64

IType

weight (7,85 kg/dm3) kg/1.000 piecesDimen-

sionA B

min. max. min. max.5 4,76 5,24 0,13 0,23 0,43 0,53 0,84 1,26

6 5,76 6,24 0,14 0,25 0,46 0,57 0,9 1,33 21,8 3,4

(7) 6,71 7,29 0,15 0,27 0,49 0,61 0,96 1,41 2,28 3,57

8 7,71 8,29 0,16 0,29 0,52 0,66 1,02 1,49 2,38 3,74

10 9,71 10,29 0,18 0,33 0,58 0,75 1,14 1,64 2,63 4,08

12 11,65 12,35 0,2 0,36 0,64 0,84 1,26 1,8 2,87 4,42

(14) 13,65 14,35 0,39 0,7 0,92 1,38 1,95 3,12 4,76

16 15,65 16,35 15,1 16,9 0,42 0,76 1 1,5 2,1 3,37 5,11

(18) 17,65 18,35 17,1 18,9 0,82 1,09 1,61 2,25 3,62 5,45

20 19,58 20,42 18,95 21 0,88 1,18 1,73 2,41 3,87 5,8

(22) 21,58 22,42 20,95 23,05 0,94 1,27 1,85 2,56 4,12 6,15

25 24,58 25,42 23,95 26,05 1,02 1,4 2,03 2,8 4,49 5,65

s

ed

k l

TORNILLO HEXAGONALHEXAGONAL BOLT

Page 47: Esparragos y Tornillos Catalogo Tecnico

46DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d (M7) M8 M10 M12 (M14) M16 (M18) M20P 1 1,25 1,5 1,75 2 2 2,5 2,5a max. 3 3,75 4,5 5,25 6 6 7,5 7,5

c min. 0,15 0,15 0,15 0,15 0,15 0,2 0,2 0,2max. 0,5 0,6 0,6 0,6 0,6 0,8 0,8 0,8

da max. 7,8 9,2 11,2 13,7 15,7 17,7 20,2 22,4

dw type min.A 9,6 11,6 14,6 15,6 16,6 17,4 19,6 20,5 22,5 25,3 28,2B 9,4 11,4 14,4 15,4 16,4 17,2 19,2 20,1 22 24,8 27,7

e type min.A 12,12 14,38 17,77 18,9 20,03 21,1 23,35 24,49 26,75 30,14 33,53B 11,94 14,2 17,59 18,72 19,85 20,88 22,78 23,91 26,17 29,56 32,95

k type

dimension 4,8 5,3 6,4 7,5 8,8 10 11,5 12,5

Amin. 4,65 5,15 6,22 7,32 8,62 9,8 11,28 12,28

max 4,95 5,45 6,56 7,68 8,98 10,18 11,72 12,72

Bmin. 4,56 5,06 6,11 7,21 8,51 9,71 11,15 12,15max. 5,04 5,54 6,69 7,79 9,09 10,29 11,85 12,85

k’ min. 3,19 3,54 4,28 5,05 5,96 6,8 7,8 8,5r min. 0,25 0,4 0,4 0,6 0,6 0,6 0,6 0,8

smax. = dimension s. 11 13 16 17 18 19 21 22 24 27 30

type min.A 10,73 12,73 15,7 16,73 17,73 18,67 20,67 21,67 23,67 26,67 29,67B 10,57 12,57 15,57 16,57 17,57 18,48 20,16 21,16 23,16 26,15 29,16

Dimen-sion

IType

weight (7,85 kg/dm3) kg/1.000 piecesA B

min. max. min. max.(7) 6,71 7,29 5,6 8 7,71 8,29 5,85

10 9,71 10,29 6,35 9,1 16,2 23,2

12 11,65 12,35 6,85 9,8 17,2 25 40 52,9

(14) 13,65 14,35 7,35 10,5 18,2 26,4 42 55,6

16 15,65 16,35 7,85 11,1 19,2 27,7 44 58,3 82 105

(18) 17,65 17,65 8,35 11,7 20,2 29,1 46 60,9 84,9 110

20 19,58 19,58 8,85 12,3 21,2 31 48 63,5 87,2 114

(22) 21,58 21,58 9,35 12,9 22,2 33 50 66,2 92,2 119

25 24,58 24,58 10 13,9 23,7 34,1 53 70,2 95,8 124

(28) 27,58 28,42 10,7 14,9 25,2 36,2 55,9 74,2 100 129

(30) 29,58 30,42 11,3 15,5 26,2 37,7 57,9 76,9 104 134

35 34,5 35,5 12,5 17,1 28,7 41,3 62,9 83,5 112 145

40 39,5 40,5 13,8 18,7 31,2 44,9 67,9 90,2 120 155

45 44,5 45,5 15 20,3 33,7 48,5 72,9 97,1 128 165

50 49,5 50,5 16,3 21,8 36,2 52 77,9 103 136 176

55 49,5 55,6 17,5 23,4 38,7 55,6 82,8 110 145 186

60 54,4 60,6 18,7 25 41,3 58,2 87,8 117 153 196

65 59,4 65,6 20 26,5 43,8 62,8 92,8 123 161 207

70 64,4 70,6 68,5 71,5 21,2 28,2 46,3 66,4 97,9 130 169 217

(75) 74,4 70,6 73,5 76,5 22,5 29,8 48,8 70 102 137 177 227

80 79,4 90,6 78,5 81,5 23,7 31,4 51,3 73,6 107 144 186 238

(85) 84,3 85,7 83,25 86,75 25 33 53,8 77,2 112 150 194 24790 89,3 90,7 88,25 91,75 26,2 34,6 56,3 80,8 117 157 202 258

s

ed

k lCon rosca hasta la cabeza DIN 933 ISO 4017Totally threaded

TORNILLO HEXAGONALHEXAGONAL BOLT

Page 48: Esparragos y Tornillos Catalogo Tecnico

47DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d (M22) M24 M27 M30 (M33) M36 (M39)P 2,5 3 3 3,5 3,5 4 4

a max. 7,5 9 9 10,5 10,5 12 12

c min. 0,2 0,2 0,2 0,2 0,2 0,2 0,3

max. 0,8 0 ,8 0,8 0,8 0,8 0,8 1

da max. 24,4 26,4 30,4 33,4 36,4 39,4 42,4

dw min. typeA 30 31,7 33,6

38 42,7 46,5 51,1 55,9B 29,5 31,4 33,2

e min. typeA 35,72 37,72 39,98

45,20 50,85 55,37 60,79 66,44B 35,03 37,29 39,55

k

dimension 14 15 17 18,7 21 22,5 25

type

Amin. 13,78 14,78

max 14,22 15,22

Bmin. 13,65 14,65 16,65 18,28 20,58 20,58 24,58

max. 14,35 15,25 17,35 19,12 21,42 22,92 25,42

k’ min. 9,6 10,3 11,7 12,8 14,4 15,5 17,2

r min. 0,8 0,8 1 1 1 1 1

s

max. = dimension s 32 34 36 41 46 50 55 60

min. typeA 31,61 33,38 35,38

40 45 49 53,8 58,8B 31 33 35

Dimen-sion

I

weight (7,85 kg/dm3) kg/1.000 piecesType

A Bmin. max. min. max.

(22) 21,58 22,42 20,95 23,05 148 190 269 25 24,58 25,42 23,95 26,05 155 199 280

(28) 27,58 28,42 26,95 29,05 161 200 292 30 29,58 30,42 28,95 31,05 168 214 310 35 34,5 35,5 33,75 36,25 181 229 319 424 543 670 86940 39,5 40,5 38,75 41,25 193 244 338 448 572 714 91045 44,5 45,5 43,75 46,25 206 259 358 472 601 748 95150 49,5 50,5 48,75 51,25 219 274 377 496 630 783 99255 54,4 55,6 53,5 56,5 232 289 397 519 659 817 103060 59,4 60,6 58,5 61,5 244 304 416 543 688 851 107065 64,4 65,6 63,5 66,5 257 319 435 566 717 886 111070 69,4 70,6 68,5 71,5 269 334 454 590 746 910 1160

(75) 74,4 75,6 73,5 76,5 282 348 473 614 775 950 120080 79,4 80,6 78,5 81,5 295 363 492 637 806 990 1240

(85) 84,3 85,7 83,25 86,75 308 378 512 661 837 1020 128090 89,3 90,7 88,25 91,75 321 393 531 685 866 1060 1320

(95) 94,3 95,7 93,25 96,75 333 408 550 708 891 1100 1360100 99,3 100,7 98,25 101,75 346 423 569 732 920 1140 1400110 109,3 110,7 108,25 111,75 371 453 608 779 978 1200 1480120 119,3 120,7 118,25 121,75 397 483 647 827 1040 1260 1560130 129,3 130,8 128 132 421 513 685 874 1090 1330 1650140 139,2 140,8 138 142 448 543 724 921 1150 1400 1730150 149,2 150,8 148 152 473 572 762 969 1210 1470 1810160 159,2 160,8 158 162 498 602 801 1010 1270 1540 1890

s

ed

k lCon rosca hasta la cabeza DIN 933 ISO 4017Totally threaded

TORNILLO HEXAGONALHEXAGONAL BOLT

Page 49: Esparragos y Tornillos Catalogo Tecnico

48DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d M42 (M45) M48 (M52)P 4,5 4,5 5 5

a max. 13,5 13,5 15 15

cmin. 0,3 0,3 0,3 0,3

max. 1 1 1 1

da max. 45,6 48,6 52,6 56,6

dw min. 59,9 64,7 69,4 74,2

e min. 71.3 76,95 82,6 88,25

k

dimension 26 28 30 33

min. 25,58 27,58 29,58 32,5

max. 26,42 28,42 30,42 33,5

k’ min. 17,9 19,3 20,9 22,8

r min. 1,2 1,2 1,6 1,6

smax. = dimension s 65 70 75 80

min. 63,1 68,1 73,1 78,1

Dimension

lType

weight (7,85 kg/dm3) kg/1.000 piecesB

min. max.35 34,5 35,5

40 39,5 40,5 1090 1330 1590

45 44,5 45,5 1130 1380 1650

50 49,5 50,5 1180 1430 1710 2090

55 54,4 55,6 1230 1490 1770 2170

60 59,4 60,6 1270 1540 1830 2240

65 65,4 65,6 1310 1600 1890 2310

70 69,4 70,6 1370 1650 1950 2390

(75) 74,4 75,6 1410 1710 2010 2460

80 79,4 80,6 1460 1760 2080 2540

(85) 84,3 85,7 1500 1810 2140 2610

90 89,3 90,7 1550 1870 2200 2680

(95) 94,3 95,7 1600 1920 2260 2750

100 99,3 100,7 1650 1980 2320 2830

110 109,3 110,7 1740 2090 2450 2970

120 119,3 120,7 1840 2190 2570 3120

130 129,2 130,8 1930 2300 2690 3260

140 139,2 140,8 2020 2410 2820 3410

150 149,2 150,8 2120 2520 2940 3550

160 159,2 160,8 2210 2630 3060 3700

(170) 169,2 170,8 2300 2740 3180 3850

180 179,2 180,8 2400 2850 3310 4000

(190) 189,08 190,92 2500 2960 3430 4150

200 199,08 200,92 2590 3060 3560 4300

s

ed

k lCon rosca hasta la cabeza DIN 933 ISO 4017Totally threaded

TORNILLO HEXAGONALHEXAGONAL BOLT

Page 50: Esparragos y Tornillos Catalogo Tecnico

49DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

TORNILLOS PARA ESTRUCTURAHIGHT STRENGTHSTRUCTURAL BOLT HV

s

e

marcas

d

bck

X C30º

z1x1

r Detalle

d q d w

r

l

dw

thread d M 12 M 16 M 20 M 22 M 24 M 27 M 30 M 36

b1) 21 26 31 32 34 40 482) 23 28 33 34 37 39 42 50

c min. 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4max. 0,6 0,6 0,8 0,8 0,8 0,8 0,8 0,8

da max. 15,2 19,2 24 26 28 32 35 41Dw min. 20 25 30 34 39 43,5 47,5 57e min. 23,91 29,56 35,03 39,55 45,2 50,85 55,37 66,44k 8 10 13 14 15 17 19 23r min. 1,2 1,2 1,5 1,5 1,5 2 2 2s 22 27 32 36 41 46 50 60

Nominal size I weight (7,85 kg/dm3) kg/1.000 pieces

30 48,035 52,040 56,0 10545 59,0 113 18050 64,0 121 194 24955 68,0 129 207 26460 72,0 137 219 279 35365 77,0 145 232 294 37170 81,0 153 244 309 389 51975 86,0 157 257 324 407 542 69580 90,0 165 269 339 425 564 72385 95,0 173 282 354 443 587 751 118699 99,0 181 288 363 449 609 779 122695 104 189 301 376 467 632 807 1266

100 197 313 393 485 645 832 1303105 205 326 408 503 666 860 1343110 213 338 423 521 687 888 1383115 221 351 438 539 708 916 1423120 229 363 453 557 729 944 1463125 237 376 468 575 750 972 1503130 245 388 483 593 771 1000 1543135 400 498 611 792 1028 1583140 413 513 629 813 1055 1623145 425 528 647 834 1083 1663150 438 543 665 855 1110 1703155 450 558 683 876 1138 1763160 573 700 897 1168 1783165 588 718 918 1194 1823170 736 939 1222 1863175 754 960 1256 1903180 772 981 1284 1943185 790 1000 1312 1983190 808 1020 1340 2023195 826 1040 1368 2063200 1060 1396 2103

1) For lengths over the stepped line.2) For lengths under the stepped line.

DIN 6914 - ISO 7412

Page 51: Esparragos y Tornillos Catalogo Tecnico

50DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

thread d1 M5 M6 M8 M10 M12 M16P 0,8 1 1,25 1,5 1,75 2

b

1) 16 18 22 26 30 38

2) 28 32 36 44

3) 49 57

d2 Hg 5 6 8 10 12 16

d3

max. 12 14 18 20 25 32

min.shape A 10,9 12,9 16,9 18,9 23,7 30,4

shapes B y C 11,57 13,57 17,57 19,48 24,48 31,38

r = 2,5 4 4 4 6 6

s

shape Amax. 8 9 11 14 17 19

min. 7,52 8,52 10,3 13,3 16,3 18,16

shapes B y Cmax. 6 7 9 12 14 17

min. 5,88 6,86 8,85 11,82 13,82 16,82

thread d1 M20 M24 (M27) M30 (M33) M36 (M39)P 1) 2,5 3 3 3,5 3,5 4 4

b

2) 46 54 60 66

3) 52 60 66 72 78 84 90

4) 65 73 79 85 91 97 103

d2 Hg 18 22 24 27 30 32 33 35 36

d3

max. 40 45 50 55 60 65 70

min.shape A 38,4 43,4 48,4 53,1 58,1 63,1 68,1

shapes B y C 39,38 44,38 49,38 54,26 59,26 64,26 69,26

r = 6 10 10 10 16 16 16

s

shape Amax. 24 28 30 34 38 41 46

min. 23,16 27,16 29,16 33 37 40 45

shapes B y C

max. 22 25 27 30 34 38 41

min. 21,79 24,79 26,79 29,79 33,75 37,75 40,75

1) For I < 120.2) For l 120 ÷ 200.3) For I >200.

DIN 444TORNILLOS DE OJO / EYE BOLTS

s

d

bl

d3 d2

Page 52: Esparragos y Tornillos Catalogo Tecnico

51DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

dimensionshape A

Ishape C

weight (7,85 kg/dm3) kg/1.000 piecesshape B

min. max. min. max. min. max.

80 78,5 81,5 79,05 80,95 79,4 80,6

90 88,25 91,75 88,9 91,1 89,3 90,7

100 98,25 101,75 98,9 101,1 99,3 100,7 334 454

110 108,25 111,75 108,9 111,1 109,3 110,7 359 489

120 118,25 121,75 118,9 121,1 119,3 120,7 383 524 618

130 128 132 128,75 131,25 129,2 130,8 408 560 663

140 138 142 138,75 141,25 139,2 140,8 433 596 708

150 148 152 148,75 151,25 149,2 150,8 457 631 753 997 1240

160 156 164 158,75 161,25 159,2 160,8 482 667 798 1050 1310 1570 1880

180 176 184 178,75 181,25 179,2 180,8 531 738 888 1160 1440 1730 2070

200 195,4 204,6 198,55 201,45 199,1 200,9 581 809 978 1270 1570 1890 2250

220 215,4 224,6 218,55 221,45 219,1 220,9 624 868 1060 1370 1690 2050 2420

240 235,4 244,6 238,55 241,45 239,1 240,9 674 939 1140 1480 1820 2200 2610

260 254,8 265,2 258,4 261,6 258,9 261 723 1010 1230 1590 1960 2350 2790

280 274,8 285,2 278,4 281,6 278,9 281 1320 1700 2100 2500 2970

300 294,8 305,2 298,4 301,6 298,9 301 1400 1810 2240 2650 3100

DIN 444TORNILLOS DE OJO / EYE BOLTS

Page 53: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

52DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

TuercasNutsANSI/DIN

Page 54: Esparragos y Tornillos Catalogo Tecnico

53DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Size d

s h eThreads per

inchesWeight per 100

nuts/Kgin mm in mm in mm

3/8” 11/16” 17,4 3/8” 9,1 3/4” 19,7 16 1,4

7/16” 3/4” 19 7/16” 10,7 7/8” 22 14 1,9

1/2” 7/8” 22,2 1/2” 12,3 1” 25,4 13 3,0

9/16” 15/16” 23,8 9/16” 13,9 1 1/16” 27 12 3,7

5/8” 11/16” 27 5/8” 15,5 1 1/4” 31,2 11 5,4

3/4” 1 1/4” 31,7 3/4” 18,7 1 3/8” 35,7 10 8,8

7/8” 1 7/16” 36,5 7/8” 21,8 1 5/8” 41,6 9 13,5

1” 1 5/8” 41,2 1” 25 1 7/8” 47,2 8 19,3

1 1/8” 1 13/16” 46 1 1/8” 28,2 2 1/16” 52 8 26,9

11/4” 2” 50,8 1 1/4” 31 2 1/4” 57,8 8 35,7

1 3/8” 2 3/16” 55,5 1 3/8” 34,1 2 1/2” 63,5 8 46,3

1 1/2” 2 3/8” 60,3 1 1/2” 37,3 2 3/4” 69,3 8 59,5

1 5/8” 2 9/16” 65 1 5/8” 40,5 2 15/16” 75 8 73,6

1 3/4” 2 3/4” 69,8 1 3/4” 43,6 3 1/16” 78,6 8 92,7

1 7/8” 2 15/16” 74,6 1 7/8” 46,8 3 3/8” 85,5 8 109,5

2” 3 1/8” 79,3 2” 50 3 9/16” 90 8 135,8

2 1/4” 3 1/2” 88,9 2 1/4” 56 3 15/16” 100 8 190,3

2 1/2” 3 7/8” 98,4 2 1/2” 62,3 4 3/8” 111,6 8 256,0

2 3/4” 4 1/4” 108 2 3/4” 70 4 7/8” 124,3 8 335,0

3” 4 5/8” 118 3” 76,2 5 3/8” 135,3 8 432,0

3 1/4” 5” 127 3 1/4” 80,9 5 3/4” 146,5 8 543

3 1/2” 5 3/8” 136,5 3 1/2” 87,3 6 3/16” 157,2 8 694

3 3/4” 5 3/4” 146 3 3/4” 93,7 6 5/8” 168,6 8 824

4” 6 1/8” 155,6 4” 100 7 1/16” 179,5 8 991

Roscado de acuerdo a ANSI B1.1 UNC hasta 1”.8 UN para diámetro 1 1/8” y superiores.Threaded according to ANSI B1.1, UNC until 1”, 8UN for 1 1/8” and up to.

Tuercas hexagonales de serie pesadaHeavy Hexagonal nuts

ANSI B18.2.2

h sd

e

30º

Page 55: Esparragos y Tornillos Catalogo Tecnico

54DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. Rosca métrica Metric-thread

TUERCAS HEXAGONALESHEXAGONAL NUTS

h sd

e

30º

Size d sh

ISO 4033e ISO thread

Weight per100 nuts/Kg

M 8 13 8 15 1,25 0,6

M 10 17 10 19,6 1,50 1,4

M 12 19 12 21,9 1,75 2

M 14 22 14 25,4 2,00 3,1

M 16 24 16 27,7 2,00 4

M 18 27 18 31,1 2,50 5,8

M 20 30 20 34,6 2,50 7,9

M 22 32 22 36,9 2,50 9,4

M 24 36 24 41,5 3,00 13,7

M 27 41 27 47,3 3,00 20

M 30 46 30 53,1 3,50 28,4

M 33 50 33 57,7 3,50 36,1

M 36 55 36 63,5 4,00 48,3

M 39 60 39 69,3 4,00 62,3

M 42 65 42 75 4,50 79,5

M 45 70 45 80,8 4,50 98,8

M 48 75 48 86,5 5,00 122

M 52 80 52 92,4 5,00 147

M 56 85 56 98,1 5,50 177

M 60 90 60 103,9 5,50 208

M 64 95 64 109,7 6,00 245

M 68 100 68 115,5 6,00 284

M 72 105 72 121,25 6,00 327

M 76 110 76 127 6,00 374

M 80 115 80 132,8 6,00 425

M 85 120 85 138,6 6,00 483

M 90 130 90 150,1 6,00 606

M 95 135 95 155,9 6,00 680

M 100 145 100 167,4 6,00 835

Page 56: Esparragos y Tornillos Catalogo Tecnico

55DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d M1 M1,2 M1,4 M1,6 M2 M2,5 M3 (M3,5) M4 M5 M6 (M7)

P 0,25 0,25 0,3 0,35 0,4 0,45 0,5 0,6 0,7 0,8 1 1

da

min. 1 1,2 1,4 1,6 2 2,5 3 3,5 4 5 6 7

max. 1,15 1,4 1,6 1,84 2,3 2,9 3,45 4 4,6 5,75 6,75 7,75

dw min. 2 2,1 2,1 2,4 3,2 4,1 4,5 5 5,8 6,8 8,8 9,5

e min. 2,71 3,28 3,28 3,48 4,38 5,45 6,01 6,58 7,66 8,79 11,05 12,12

mmax. 0,8 1 1,2 1,3 1,6 2 2,4 2,8 3,2 4 5 5,5

min. 0,55 0,75 0,95 1,05 1,35 1,75 2,15 2,55 2,9 3,7 4,7 5,2

m’ min. 0,44 0,6 0,76 0,84 1,08 1,4 1,72 2,04 2,32 2,96 3,76 4,16

smax.=med. nom. 2,5 3 3 3,2 4 5 5,5 6 7 8 10 11

min. 2,4 2,9 2,9 3,08 3,88 4,82 5,32 5,82 6,78 7,78 9,78 10,73

Thread dM8

M8 x 1−

M10M10 x 1,25

M10 x 1

M12M12 x 1,25M12 x 1,5

(M14)(M14 x 1,5)

M16(M16 x 1,5)

(M18)(M18 x 1,5)(M18 x 2)

M20M20 x 1,5M20 x 2

P 1,25 1,5 1,75 2 2 2,5 2,5

da

min. 8 10 12 14 16 18 20

max. 8,75 10,8 13 15,1 17,3 19,5 21,6

dw min. 11,3 15,3 17,2 20,2 22,2 25,3 28,2

e min. 14,38 18,9 21,1 24,49 26,75 29,56 32,95

mmax. 6,5 8 10 11 13 15 16

min. 6,14 7,64 9,64 10,3 12,3 14,3 14,9

m’ min. 4,91 6,11 7,71 8,24 9,84 11,44 11,92

smax.=med. nom. 13 17 19 22 24 27 30

min. 12,73 16,73 18,67 21,67 23,67 26,16 29,16

Rosca métrica / Metric-thread

TUERCAS HEXAGONALES DIN 934 / ISO 4032HEXAGONAL NUTS DIN 934 / ISO 4032

s

e

m

d dw

Page 57: Esparragos y Tornillos Catalogo Tecnico

56DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread d(M22)

(M22 x 1,5)(M22 x 2)

M24M24 x 2)

(M27)(M27 x 2)

M30M30 x 2

(M33)(M33 x 2)

M36M36 x 3

(M39)(M39 x 3)

P 2,5 3 3 3,5 3,5 4 4

da

min. 22 24 27 30 33 36 39

max. 23,7 25,9 29,1 32,4 35,6 38,9 42,1

dw min. 29,5 33,2 38 42,7 46,6 51,1 55,9

e min. 35,03 39,55 45,20 50,85 55,37 60,79 66,44

mmax. 18 19 22 24 26 29 31

min. 16,9 17,7 20,7 22,7 24,7 27,4 29,4

m’ min. 13,52 14,16 16,56 18,16 19,76 21,92 23,52

smax.=med. nom. 32 36 41 46 50 55 60

min. 31 35 40 45 49 53,8 58,8

Thread d M42M42 x 3

(M45)(M45 x 3)

M48M48 x 3

(M52)(M52 x 3)

M56M56 x 4

(M60)(M60 x 4)

M64M64 x 4

P 4,5 4,5 5 5 5,5 5,5 6

da

min. 42 45 48 52 56 60 64

max. 45,4 48,6 51,8 56,2 60,5 64,8 69,1

dw min. 60,6 64,7 69,4 74,2 78,7 83,4 88,2

e min. 72,09 76,95 82,60 88,25 93,56 99,21 104,86

mmax. 34 36 38 42 45 48 51

min. 32,4 34,4 36,4 40,4 43,4 46,4 49,1

m’ min. 25,9 27,5 29,1 32,3 34,7 37,1 39,3

smax.=med. nom. 65 70 75 80 85 90 95

min. 63,8 68,1 73,1 78,1 82,8 87,8 92,8

Thread d(M68)

(M68 x 4)M72 x 6M72 x 4

(M76 x 6)(M76 x4)

M80 x 6M80 x 4

(M85 x 6)(M85 x 4)

M90 x 6M90 x 4

M100 x 6M100 x 4

P 6 − − − − − −

da

min. 68 72 76 80 85 90 100

max. 73,4 77,8 82,1 86,4 91,8 87,2 108

dw min. 92,9 97,7 102,4 107,2 111,9 121,1 135,4

e min. 110,51 116,16 121,81 127,46 133,11 144,08 161,02

mmax. 54 58 61 64 68 72 80

min. 52,1 56,1 59,1 62,1 66,1 70,1 78,1

m’ min. 41,7 44,9 47,3 49,7 52,9 56, 1 62,5

smax.=med. nom. 100 105 110 115 120 130 145

min. 97,8 102,8 107,8 112,8 117,8 127,5 142,5

Rosca métrica / Metric-thread

TUERCAS HEXAGONALES DIN 934 / ISO 4032HEXAGONAL NUTS DIN 934 / ISO 4032

Page 58: Esparragos y Tornillos Catalogo Tecnico

57DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Thread dM110 x 6 M125 x 6 M140 x 6 M160 x 6M110x4 M125x4 — —

da

min. 110 125 140 160max. 119 135 151 171

dw min. 144,9 168,6 185,6 214,1

e min. 172,32 200,57 220,80 254,70

mmax. 88 100 112 128min 85,8 97,8 109,8 125 5

m’ min. 68,6 78,2 87,8 100

smax. = media nom. s 155 180 200 230

min. 152,5 177,5 195,4 225,4

TABLA DE PESOS / WEIGHT TABLE

Thread d M 1 M 1,2 M 1,4 M 1,6 M 2 M 2,5 M 3

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 0,03 0,054 0,063 0,076 0,142 0,28 0,384

Thread d M 3,5 M 4 M 5 M 6 M 7 M 8 M 10

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 0,514 0,81 1,23 2,5 3,12 5,2 11,6

Thread d M 12 M 14 M 16 M 17 M 20 M 22 M 24

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 17,3 25 33,3 49,4 64,4 79 110

Thread d M 27 M 30 M 33 M 36 M 39 M 42 M 45

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 165 223 288 393 502 652 800

Thread d M 48 M 52 M 56 M 60 M 64 M 68 M 72 x 6

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 977 1220 1420 1690 1980 2300 2670

Thread d M 76 x 6 M 80 x 6 M 85 x 6 M 90 x 6 M 100 x 6

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 3040 3440 3930 4930 6820

Thread d M 110 x 6 M 125 x 6 M 140 x 6 M 160 x 6

Weight (7,85 kg/dm3) kg per 1000 pieces ≈ 8200 13000 17500 26500

s

ed dw

m

Rosca métrica / Metric-thread

TUERCAS HEXAGONALES DIN 934 / ISO 4032HEXAGONAL NUTS DIN 934 / ISO 4032

Page 59: Esparragos y Tornillos Catalogo Tecnico

58DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. Rosca UNC / 8 UN / Inches-thread UNC / 8 UN

s

ed

m

Thread d d s e m kg/1.000 pieces

1/8”3/16”1/4”

5/16”3/8”

2,44

5,56,58

69

111417

−−

12,716,219,6

2,334

6,257,75

0,381,58

35,8

10,8

7/16”1/2”

9/16”5/8”3/4”

9,511

11,51316

1922242732

21,925,4

−31,236,9

910

10,512,7015,5

15,224,330

42,372,8

7/8”1”

1 1/8”1 1/4”1 3/8”

1820222528

3641465055

41,647,353,157,7

18,018,52124

25,5

98,7139196259360

1 1/2”1 5/8”1 3/4”1 7/8”

2”

3032353840

6065707580

69,3−

80,8−

92,4

2831

33,53640

443587709917

1060

2 1/4”2 1/2”2 3/4”

3”

45505560

8595

105110

98110121127

45515361

1280177024102750

TUERCAS HEXAGONALES DIN 934 / ISO 4032HEXAGONAL NUTS DIN 934 / ISO 4032

Page 60: Esparragos y Tornillos Catalogo Tecnico

59DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. Con entrecaras grandes para uniones HV / High strength structural hexagonal nuts HV

TUERCAS HEXAGONALES DIN 6915 / ISO 7414HEXAGONAL NUTS DIN 6915 / ISO 7414

d M12 M16 M20 M22 M24 M27 M30 M36

dw min. 20 25 30 34 39 43.5 47,5 57

e min. 23,91 29,56 35,06 39,55 45,2 50,85 55,37 66,44

m 10 13 16 18 19 22 24 29

s 22 27 32 36 41 46 50 60

Weight (7,85 kg/dm3) kg/1.000 pieces ≈ 23,3 44,8 73,9 104 155 224 300 515

s

e

m

d dw

30º

120º

mark

Page 61: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

60DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

ArandelasPlain washer

DIN

Page 62: Esparragos y Tornillos Catalogo Tecnico

61DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ARANDELAS PLANASPLAIN WASHER DIN 125 / ISO 7089

d2

s

d1

d1 d2 s

Weight (7,85

kg/dm3) kg/1.000 pieces ≈

for metric-

boltsd1 d2 s

Weight (7,85

kg/dm3) kg/1.000 pieces ≈

for metric-

boltsd1 d2 s

Weight (7,85

kg/dm3) kg/1.000 pieces ≈

for metric-

bolts

1,7 4 0,3 0,024 1,6 25 44 4 32,3 24 62 110 9 458 60

1,8 4,5 0,3 0,031 1,7 27 50 4 43,7 26 66 115 9 492 64

2,2 5 0,3 0,037 2 28 50 4 42,3 27 70 120 10 586 68

2,5 6 0,5 0,092 2,3 29 50 4 40,9 28 74 125 10 625 72

2,7 6,5 0,5 0,108 2,5 31 56 4 53,6 30 78 135 10 748 76

2,8 7 0,5 0,127 2,6 33 60 5 77,5 32 82 140 12 952 80

3,2 7 0,5 0,120 3 34 60 5 75,4 33 87 145 12 995 85

3,7 8 0,5 0,156 3,5 36 66 5 94,3 35 93 160 12 1250 90

4,3 9 0,8 0,308 4 37 66 5 92,0 36 98 165 12 1300 95

5,3 10 1 0,443 5 39 72 6 135 38 104 175 14 1710 100

6,4 12,5 1,6 1,140 6 40 72 6 133 39 109 180 14 1770 105

7,4 14 1,6 1,39 7 41 72 6 130 40 114 185 14 1830 110

8,4 17 1,6 2,14 8 43 78 7 183 42 119 200 14 2230 115

10,5 21 2 4,08 10 46 85 7 220 45 124 210 16 2830 120

13 24 2,5 6,27 12 50 92 8 294 48 12,9 220 16 3130 125

15 28 2,5 8,60 14 52 92 8 284 50 134 220 16 3000 130

17 30 3 11,3 16 54 98 8 330 52 139 230 16 3310 135

19 34 3 14,7 18 57 105 9 431 55 144 240 18 4090 140

21 37 3 17,2 20 58 105 9 425 56 149 250 18 4470 145

23 39 3 18,4 22 60 110 9 471 58 155 250 18 4270 150

* mm values Tipo A sin bisel Tipo B con bisel Type A without chamfer Type B with chamfer

Page 63: Esparragos y Tornillos Catalogo Tecnico

62DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

d1 d2 s

Weight (7,85

kg/dm3) kg/1.000 pieces ≈

for metric-

bolts

d1 d2 s

Weight (7,85

kg/dm3) kg/1.000 pieces ≈

for metric-

bolts 1) 1)

5,5 5,8 10 1 0,43 5 45 − 78 7 175 42

6,6 7 12,5 1,6 1,11 6 48 − 85 7 212 45

7,6 − 14 1,6 1,36 7 52 − 92 8 284 48

9 9,5 17 1,6 2,05 8 56 − 98 8 319 52

11 11,5 21 2 3,94 10 62 61 105 9 398 56

14 − 24 2,5 5,85 12 66 65 110 9 430 60

16 − 28 2,5 8,13 14 70 − 115 9 462 64

18 − 30 3 10,6 16 78 − 125 10 588 72

20 − 34 3 14,0 18 86 − 140 12 902 80

22 23 37 3 16,4 20 96 − 160 12 1210 90

24 − 39 3 17,5 22 107 106 175 14 1650 100

26 27 44 4 31,1 24 117 116 185 14 1770 110

30 − 50 4 39,4 27 127 126 210 16 2760 120

33 − 56 4 50,5 30 132 − 220 16 3040 125

36 − 60 5 71,0 33 137 136 220 16 2920 130

39 − 66 5 87,3 36 147 146 240 18 4000 140

42 − 72 6 126 39 158 157 250 18 4160 150

1) Old diameters

* mm values

d2

s

d1

ARANDELAS PLANASPLAIN WASHER DIN 126 / ISO 7091

Page 64: Esparragos y Tornillos Catalogo Tecnico

63DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ARANDELAS DE MUELLESPRING LOCK WASHER DIN 127

d 2

d 2

Type A positiv pattern Type B plane pattern

h h

s

d d 1

b

Size

d1 d2 h b s r k Weight (7,85

kg/dm3) kgs 1.000 pieces ≈

for metric-

bolts

dif. adm.

+0…

type A type B

dif. adm.max. min. max. min. max.

dif.adm.

2 2,1 + 0,3 4,4 − − 1 1,2 0,9 ± 0,1 0,5 ± 0,1 0,1 − 0,033 22,3 2,4 + 0,3 4,9 − − 1,2 1,4 1 ± 0,1 0,6 ± 0,1 0,1 − 0,050 2,32,5 2,6 + 0,3 5,1 − − 1,2 1,4 1 ± 0,1 0,6 ± 0,1 0,1 − 0,053 2,52,6 2,7 + 0,3 5,2 − − 1,2 1,4 1 ± 0,1 0,6 ± 0,1 0,1 − 0,054 2,63 3,1 + 0,3 6,2 1,9 2,1 1,6 1,9 1,3 ± 0,1 0,8 ± 0,1 0,2 0,15 0,112 3

3,5 3,6 + 0,3 6,7 1,9 2,2 1,6 1,9 1,3 ± 0,1 0,8 ± 0,1 0,2 0,15 0,12 3,54 4,1 + 0,3 7,6 2,1 2,5 1,8 2,1 1,5 ± 0,1 0,9 ± 0,1 0,2 0,15 0,18 45 5,1 + 0,3 9,2 2,7 3,2 2,4 2,8 1,8 ± 0,1 1,2 ± 0,1 0,2 0,15 0,36 56 6,1 + 0,4 11,8 3,6 4,2 3,2 3,8 2,5 ± 0,15 1,6 ± 0,1 0,3 0,2 0,83 67 7,1 + 0,4 12,8 3,6 4,2 3,2 3,8 2,5 ± 0,15 1,6 ± 0,1 0,3 0,2 0,93 78 8,1 + 0,4 14,8 4,6 5,4 4 4,7 3 ± 0,15 2 ± 0,1 0,5 0,3 1,60 8

10 10,2 + 0,5 18,1 5 5,9 4,4 5,2 3,5 ± 0,2 2,2 ± 0,15 0,5 0,3 2,53 1012 12,2 + 0,5 21,1 5,8 6,8 5 5,9 4 ± 0,2 2,5 ± 0,15 1 0,4 3,82 1214 14,2 + 0,5 24,1 6,8 8 6 7,1 4,5 ± 0,2 3 ± 0,15 1 0,4 6,01 1416 16,2 + 0,8 27,4 7,8 9,2 7 8,3 5 ± 0,2 3,5 ± 0,2 1 0,4 8,91 1618 18,2 + 0,8 29,4 7,8 9,2 7 8,3 5 ± 0,2 3,5 ± 0,2 1 0,4 9,73 1820 20,2 + 1 33,6 8,8 10,4 8 9,4 6 ± 0,2 4 ± 0,2 1 0,4 15,2 2022 22,5 + 1 35,9 8,8 10,4 8 9,4 6 ± 0,2 4 ± 0,2 1 0,4 16,5 2224 24,5 + 1 40 11 13 10 11,8 7 ± 0,25 5 ± 0,2 1,6 0,5 26,2 2427 27,5 + 1 43 11 13 10 11,8 7 ± 0,25 5 ± 0,2 1,6 0,5 28,7 2730 30,5 + 1,2 48,2 13,6 16,1 12 14,2 8 ± 0,25 6 ± 0,2 1,6 0,8 44,3 3033 33,5 + 1,2 55,2 13,6 16,1 12 14,2 10 ± 0,25 6 ± 0,2 1,6 0,8 63 3336 36,5 + 1,2 58,2 13,6 16,1 12 14,2 10 ± 0,25 6 ± 0,2 1,6 0,8 67,3 3639 39,5 + 1,2 61,2 13,6 16,1 12 14,2 10 ± 0,25 6 ± 0,2 1,6 0,8 71,7 3942 42,5 + 1,2 68,2 15,6 18,4 14 16,5 12 ± 0,25 7 ± 0,25 2 0,8 111 4245 45,5 + 1,2 71,2 15,6 18,4 14 16,5 12 ± 0,25 7 ± 0,25 2 0,8 117 4548 49 + 1,5 75 15,6 18,4 14 16,5 12 ± 0,25 7 ± 0,25 2 0,8 123 4852 53 + 1,5 83 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 182 5256 57 + 1,5 87 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 193 5660 61 + 1,5 91 18 21,2 18 18,9 14 ± 0,25 8 ± 0,25 2 1 203 6064 65 + 1,5 95 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 218 6472 73 + 1,5 103 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 240 7280 81 + 1,5 111 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 262 8090 91 + 1,5 121 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 290 90

100 101 + 1,5 131 18 21,2 16 18,9 14 ± 0,25 8 ± 0,25 2 1 318 100

Page 65: Esparragos y Tornillos Catalogo Tecnico

64DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. DIN 6916

ARANDELAS REDONDAS PARA UNIONES HVHIGH STRENGTH STRUCTURAL WASHER HV

d2 d1

s

c

d1 d2

cf s

Weight (7,85 kg/dm3) kgs

1.000 pieces ≈

for metric-bolts

13 24 1,6+0,3

00,5 3 7,03 M12

17 30 1,6+0,3

01 4 14,6 M16

21 37 2+0,5

01 4 19,6 M20

23 39 2+0,5

01 4 24,3 M22

25 44 2+0,5

01 4 30,6 M24

28 50 2,5+0,5

01 5 50,2 M27

31 56 2,5+0,5

01 5 63,2 M30

37 66 3+0,5

01,5 6 115 M36

* mm values

Page 66: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

65DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

JuntasGasketsASME/DIN

Page 67: Esparragos y Tornillos Catalogo Tecnico

66DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS PLANASFLAT GASKETS

DIN-2690

∅ NOMINAL

∅ INTERIOR

∅ EXTERIOR · PN

6 10 16 25 40

10 18 38 45 45

15 20 43 50 50

20 25 53 60 60

25 30 63 70 70

32 40 75 82 82

40 50 85 92 92

50 60 95 107 107

65 77 115 127 127

80 90 132 142 142

100 114 152 162 162 168 168

125 140 182 192 192 195 195

150 168 207 218 218 225 225

200 220 262 273 273 285 292

250 273 318 328 330 342 353

300 325 373 378 385 402 418

350 368 423 438 445 458 475

400 420 473 490 497 515 547

450 470 528 540 557 565 572

500 520 578 595 618 625 628

600 620 680 695 735 730 745

DIN-2691

∅ NOMINAL

∅ INTERIOR

∅ EXTERIOR

10 24 34

15 29 39

20 36 50

25 43 57

32 51 65

40 61 75

50 73 87

65 95 109

80 106 120

100 129 149

125 155 175

150 183 203

200 239 259

250 292 312

300 343 363

350 395 421

400 447 473

500 549 575

600 649 675

DIN-2692

∅ NOMINAL

∅ INTERIOR

∅ EXTERIOR

10 18 34

15 22 39

20 28 50

25 35 57

32 43 65

40 49 75

50 61 87

65 77 109

80 90 120

100 115 149

125 141 175

150 169 203

200 220 259

250 274 312

300 325 363

350 368 421

400 420 473

500 520 575

600 620 675

ANSI B16.21 RF.

∅ NOMINAL

∅ INTERIOR

∅ EXTERIOR · LBS150 300 400 600

1/2” 21 48 54 54 543/4” 27 57 67 67 671” 33 67 73 73 73

1.1/4” 42 76 82 82 82 1.1/2” 48 86 95 95 95

2” 60 105 111 111 1112.1/2” 73 124 130 130 130

3” 89 136 149 149 1494” 114 174 181 178 194 5” 141 196 210 213 2416” 168 222 250 247 2668” 219 279 308 305 320

10” 273 340 362 359 40012” 324 410 422 419 45714” 356 451 486 483 492 16” 406 514 540 537 565 18” 457 549 597 594 61320” 508 606 654 648 68224” 610 717 774 768 790

ANSI B16.21 - 150 LBS.- F.F.

∅ NOMINAL

∅ INTERIOR

∅ EXTERIOR

NºOF HOLES

∅HOLES

∅ BOLT CIRCLE

1/2” 21 89 4 16 60,3 3/4” 27 98 4 16 69,81” 33 107 4 16 79,4

1.1/4” 42 117 4 16 88,91.1/2” 48 127 4 16 98,4

2” 60 152 4 19 120,62.1/2” 73 177 4 19 139,7

3” 89 190 4 19 152,44” 114 228 8 19 190,55” 141 254 8 22 215,96” 168 279 8 22 241,3 8” 219 342 8 22 298,4

10” 273 406 12 25 361,9 12” 324 482 12 25 431,8 14” 356 533 12 29 476,216” 406 596 16 29 539,718” 457 635 16 32 577,8 20” 508 698 20 32 63524” 610 812 20 35 749,3

Page 68: Esparragos y Tornillos Catalogo Tecnico

67DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS ESPIROMETÁLICAS / ASME B16.20SPIRAL-WOUND GASKETS / ASME B16.20

DIMENSIONES DE JUNTAS ESPIROMETALICAS PARA BRIDAS S/ASME ANSI B16.5DIMENSIONS FOR SPIRAL-WOUND GASKETS USED WITH ASME/ANSI B 16.5 FLANGES

Outside Diameter of Gasket (2)

Flange Size

(NPS)

Classes 150, 300, 400, 600

Classes 900,

1500, 2500

Inside Diameter of Gasket by Class (3) Outside Diameter of Centering Ring by Class (4)

150 300 400 600 900 1500 2500 150 300 400 600 900 1500 2500

1/2 1.25 1.25 0.75 0.75 (5) 0.75 (5) 0,75 0,75 1,88 2,13 (5) 2,13 (5) 2,50 2,75

3/4 1.56 1.56 1.00 1.00 (5) 1.00 (5) 1,00 1,00 2,25 2,63 (5) 2,63 (5) 2,75 3,00

1 1.88 1.88 1.25 1.25 (5) 1.25 (5) 1.25 1.25 2.63 2.88 (5) 2.88 (5) 3.13 3.38

1 1/4 2.38 2.38 1.88 1.88 (5) 1.88 (5) 1.56 1.56 3.00 3.25 (5) 3.25 (5) 3.50 4.13

1 1/2 2.75 2.75 2.13 2.13 (5) 2.13 (5) 1.88 1.88 3.38 3.75 (5) 3.75 (5) 3.88 4.63

2 3.38 3.38 2.75 2.75 (5) 2.75 (5) 2.31 2.31 4.13 4.38 (5) 4.38 (5) 5.63 5.75

2 1/2 3.88 3.88 3.25 3.25 (5) 3.25 (5) 2.75 2.75 4.88 5.13 (5) 5.13 (5) 6.50 6.63

3 4.75 4.75 4.00 4.00 (5) 4.00 3.75 3.63 3.63 5.38 5.88 (5) 5.88 6.63 6.88 7.75

4 5.88 5.88 5.00 5.00 4.75 4.75 4.75 4.63 4.63 (1) 6.88 7.13 7.00 7.63 8.13 8.25 9.25

5 7.00 7.00 6.13 6.13 5.81 5.81 5.81 5.63 5.63 (1) 7.75 8.50 8.38 9.50 9.75 10.00 11.00

6 8.25 8.25 7.19 7.19 6.88 6.88 6.88 6.75 6.75 (1) 8.75 9.88 9.75 10.50 11.38 11.13 12.50

8 10.38 10.13 9.19 9.19 3.88 8.88 8.75 8.50 8.50 (1) 11.00 12.13 12.00 12.63 14.13 13.88 15.25

10 12.50 12.25 11.31 11.31 10.81 10.81 10.88 10.50 10.63 (1) 13.38 14.25 14.13 15.75 17.13 17.13 18.75

12 14.75 14.50 13.38 13.38 12.88 12.88 12.75 12.75 (1) 12.50 (1) 16.13 16.63 16.50 18.00 19.63 20.50 21.63

14 16.00 15.75 14.63 14.63 14.25 14.25 14.00 14.25 (1) (5) 17.75 19.13 19.00 19.38 20.50 22.75 (5)

16 18.25 18.00 16.63 16.63 16.25 16.25 16.25 16.00 (1) (5) 20.25 21.25 21.13 22.25 22.63 25.25 (5)

18 20.75 20.50 18.69 18.69 18.50 18.50 19.25 18.25 (1) (5) 21.63 23.50 23.38 24.13 25.13 27.75 (5)

20 22.75 22.50 20.69 20.69 20.50 20.50 20.50 20.25 (1) (5) 23.88 25.75 25.50 26.88 27.50 29.75 (5)

24 27.00 26.75 24.75 24.75 24.75 24.75 24.75 (1) 24.25 (1) (5) 28.25 30.50 30.25 31.13 33.00 35.50 (5)

NOTES(1) Inner rings are required for all PTFE filled gaskets and for Class 900 gaskets, NPS 24; Class 1500 gaskets, NPS 12 through NPS 24, and Class 2500 gaskets, NPS 4

through NPS 12 (see para. 3.2.5 and Table 12).(2) The gasket outside diameter tolerance for NPS 1/2 throught NPS 8 is ±0.03 in.; for NPS 10 throught NPS 24, +0.06 in., -0.03 in.(3) The gasket inside diameter tolerance for NPS 1/2 throught NPS 8 is ±0.016 in.; for NPS 10 throught NPS 24, ±0.03 in.(4) The centering ring outside diameter tolerance is ±0.03 in.(5) There are no Class 400 flanges in NPS 1/2 through NPS 3 (use Class 600), Class 900 flanges NPS in 1/2 through NFS 2 1/2 (use Class 1500), or Class 2500 flanges

NPS 14 and larger.

Centering ring

0.175 in. thick

inner ring (Note 1).0.112 in.- 0.131 in. thick

Gasket outside diameterGasket inside diameter

Centering ring outside diameter

Approximate0.06 in.(bead)

Boltdiameter

Clearance0.06 in.

Bolt andbolt hole

0.117 in. - 0.131 in.thick

Page 69: Esparragos y Tornillos Catalogo Tecnico

68DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

DIMENSIONS FOR SPIRAL-WOUND GASKETS USED WITH ASME B 16.47 A FLANGESDIMENSIONES DE JUNTAS ESPIROMETALICAS PARA BRIDAS S/ASME ANSI B16.47 A

Class 150 Class 300 Class 400 Class 600 Class 900 (1)

GasketCentering

RingGasket

Centering Ring

GasketCentering

RingGasket

Centering Ring

GasketCentering

Ring

Flange

Size

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

(NPS) (2) (3) (4) (2) (3) (4) (2) (3) (4) (2) (3) (4) (2) (3) (4)

26 26.50 27.75 30.50 27.00 29.00 32.88 27.00 29.00 32.75 27.00 29.00 34.13 27.00 29.00 34.75

28 28.50 29.75 32.75 29.00 31.00 35.38 29.00 31.00 35.13 29.00 31.00 36.00 29.00 31.00 37.25

30 30.50 31.75 34.75 31.25 33.25 37.50 31.25 33.25 37.25 31.25 33.25 38.25 31.25 33.25 39.75

32 32.50 33.88 37.00 33.50 35.50 39.63 33.50 35.50 39.50 33.50 35.50 40.25 33.50 35.50 42.25

34 34.50 35.88 39.00 35.50 37.50 41.63 35.50 37.50 41.50 35.50 37.50 42.25 35.50 37.50 44.75

36 36.50 38.13 41.25 37.63 39.63 44.00 37.63 39.63 44.00 37.63 39.63 44.50 37.75 39.75 47.25

38 38.50 40.13 43.75 38.50 40.00 41.50 38.25 40.25 42.25 39.00 41.00 43.50 40.75 42.75 47.25

40 40.50 42.13 45.75 40.25 42.13 43.88 40.38 42.38 44.38 41.25 43.25 45.50 43.25 45.25 49.25

42 42.50 44.25 48.00 42.25 44.13 45.88 42.38 44.38 46.38 43.50 45.50 48.00 45.25 47.25 51.25

44 44.50 46.38 50.25 44.50 46.50 48.00 44.50 46.50 48.50 45.75 47.75 50.00 47.50 49.50 53.88

46 46.50 48.38 52.25 46.38 48.38 50.13 47.00 49.00 50.75 47.75 49.75 52.25 50.00 52.00 56.50

48 48.50 50.38 54.50 48.63 50.63 52.13 49.00 51.00 53.00 50.00 52.00 54.75 52.00 54.00 58.50

50 50.50 52.50 56.50 51.00 53.00 54.25 51.00 53.00 55.25 52.00 54.00 57.00 (5) (5) (5)

52 52.50 54.50 58.75 53.00 55.00 56.25 53.00 55.00 57.25 54.00 56.00 59.00 (5) (5) (5)

54 54.50 56.50 61.00 55.25 57.25 58.75 55.25 57.25 59.75 56.25 58.25 61.25 (5) (5) (5)

56 56.50 58.50 63.25 57.25 59.25 60.75 57.25 59.25 61.75 58.25 60.25 63.50 (5) (5) (5)

58 58.50 60.50 65.50 59.50 61.50 62.75 59.25 61.25 63.75 60.50 62.50 65.50 (5) (5) (5)

60 60.50 62.50 67.50 61.50 63.50 64.75 61.75 63.75 66.25 62.75 64.75 68.25 (5) (5) (5)

NOTES(1) Inner rings are required for all PTFE gaskets and Class 900 gaskets, NPS 26 through NPS 48.(2) The gasket inside diameter tolerance for NPS 26 throught NPS 34 is ±0.03 in.; and the tolerance for NPS 36 throught NPS 60, ±0.05 in.(3) The gasket outside diameter tolerance for NPS 26 throught NPS 60 is ±0.06 in.(4) The centering ring outside diameter tolerance is ±0.03 in.(5) There are no Class 900 flanges NPS 50 and larger.

Centering ring

0.175 in. thick

inner ring (Note 1).0.112 in.- 0.131 in. thick

Gasket outside diameterGasket inside diameter

Centering ring outside diameter

Approximate0.06 in.(bead)

Boltdiameter

Clearance0.06 in.

Bolt andbolt hole

0.117 in. - 0.131 in.thick

JUNTAS ESPIROMETÁLICAS / ASME B16.20SPIRAL-WOUND GASKETS / ASME B16.20

Page 70: Esparragos y Tornillos Catalogo Tecnico

69DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

DIMENSIONS FOR SPIRAL-WOUND GASKETS USED WITH ASME B 16.47 B FLANGESDIMENSIONES DE JUNTAS ESPIROMETALICAS PARA BRIDAS S/ASME ANSI B16.47 B

Class 150 Class 300 Class 400 Class 600 Class 900 (1)

GasketCentering

RingGasket

Centering Ring

GasketCentering

RingGasket

Centering Ring

GasketCentering

Ring

Flange

Size

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

Inside

Diameter

Outside

Diameter

Outside

Diameter

(NPS) (2) (3) (4) (2) (3) (4) (2) (3) (4) (2) (3) (4) (2) (3) (4)

26 26.50 27.50 28.56 26.50 28.00 30.38 26.25 27.50 29.38 26.12 28.13 30.13 27.25 29.50 33.00

28 28.50 29.50 30.56 28.50 30.00 32.50 28.13 29.50 31.50 27.75 29.75 32.25 29.25 31.50 35.50

30 30.50 31.50 32.56 30.50 32.00 34.88 30.13 31.75 33.75 30.63 32.63 34.63 31.75 33.75 37.75

32 32.50 33.50 34.69 32.50 34.00 37.00 32.00 33.88 35.88 32.75 34.75 36.75 34.00 36.00 40.00

34 34.50 35.75 36.81 34.50 36.00 39.13 34.13 35.88 37.88 35.00 37.00 39.25 36.25 38.25 42.25

36 36.50 37.75 38.88 36.50 38.00 41.25 36.13 38.00 40.25 37.00 39.00 41.25 37.25 39.25 44.25

38 38.37 39.75 41.13 39.75 41.25 43.25 38.25 40.25 42.25 39.00 41.00 43.50 40.75 42.75 47.25

40 40.25 41.88 43.13 41.75 43.25 45.25 40.38 42.38 44.38 41.25 43.25 45.50 43.25 45.25 49.25

42 42.50 43.88 45.13 43.75 45.25 47.25 42.38 44.38 46.38 43.50 45.50 48.00 45.25 47.25 51.25

44 44.25 45.88 47.13 45.75 47.25 49.25 44.50 46.50 48.50 45.75 47.75 50.00 47.50 49.50 53.88

46 46.50 48.19 49.44 47.88 49.38 51.88 47.00 49.00 50.75 47.75 49.75 52.25 50.00 52.00 56.50

48 48.50 50.00 51.44 49.75 51.63 53.88 49.00 51.00 53.00 50.00 52.00 54.75 52.00 54.00 58.50

50 50.50 52.19 53.44 51.88 53.38 55.88 51.00 53.00 55.25 52.00 54.00 57.00 (5) (5) (5)

52 52.50 54.19 55.44 53.88 55.38 57.88 53.00 55.00 57.25 54.00 56.00 59.00 (5) (5) (5)

54 54.50 56.00 57.63 55.25 57.25 60.25 55.25 57.25 59.75 56.25 58.25 61.25 (5) (5) (5)

56 56.88 58.18 59.63 58.25 60.00 62.75 57.25 59.25 61.75 58.25 60.25 63.50 (5) (5} (5)

58 59.07 60.19 62.19 60.44 61.94 65.19 59.25 61.25 63.75 60.50 62.50 65.50 (5) (5) (5)

60 61.31 62.44 64.19 62.56. 64.19 67.19 61.75 63.75 66.25 62.75 64.75 68.25 (5) (5) (5)

NOTES(1) Inner rings are required for all PTFE gaskets and Class 900 gaskets, NPS 26 through NPS 48.(2) The gasket inside diameter tolerance for NPS 26 throught NPS 34 is ±0.03 in.; and the tolerance for NPS 36 throught NPS 60, ±0.05 in.(3) The gasket outside diameter tolerance for NPS 26 throught NPS 60 is ±0.06 in.(4) The centering ring outside diameter tolerance is ±0.03 in.(5) There are no Class 900 flanges NPS 50 and larger.

Centering ring

0.175 in. thick

inner ring (Note 1).0.112 in.- 0.131 in. thick

Gasket outside diameterGasket inside diameter

Centering ring outside diameter

Approximate0.06 in.(bead)

Boltdiameter

Clearance0.06 in.

Bolt andbolt hole

0.117 in. - 0.131 in.thick

JUNTAS ESPIROMETÁLICAS / ASME B16.20SPIRAL-WOUND GASKETS / ASME B16.20

Page 71: Esparragos y Tornillos Catalogo Tecnico

70DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

INNER RING INSIDE DIAMETERS FOR SPIRAL-WOUND GASKETSDIAMETROS DEL ANILLO INTERIOR PARA JUNTAS ESPIROMETALICAS

Flange Size (NPS)

Pressure Class

150 300 400 600 900 1500 200

1/2 0.56 0.56 (1) 0.56 (1) 0.56 0.563/4 0.81 0.81 (1) 0.81 (1) 0.81 0.811 1.06 1.06 (1) 1.06 (1) 1.06 1.06

1 1/4 1.50 1.50 (1) 1.50 (1) 1.31 (2) 1.31 (2)1 1/2 1.75 1.75 (1) 1.75 (1) 1.63 (2) 1.63 (2)

2 2.19 2.19 (1) 2.19 (1) 2.06 (2) 2.06 (2)2 1/2 2.62 2.62 (1) 2.62 (1) 2.50 (2) 2.50 (2)

3 3.19 3.19 (1) 3.19 3.19 3.19 3.194 4.19 4.19 4.19 4.19 4.19 4.19 4.19 (3)5 5.19 5.19 5.19 5.19 5.19 5.19 5.19 (3)6 6.19 6.19 6.19 6.19 6.19 6.19 6.19 (3)8 8.50 8.50 8.50 8.25 8.25 8.12 7.88 (3)

10 10.56 10.56 10.56 10.25 10.25 10.15 9.75 (3)12 12.50 12.50 12.50 12.50 12.38 12.38 (3) 11.50 (3)14 13.75 13.75 13.75 13.75 13.50 13.38 (3) (1)16 15.75 15.75 15.75 15.75 15.50 15.25 (3) (1)18 17.69 17.69 17.69 17.69 17.50 17.25 (3) (1)20 19.69 19.69 19.69 19.69 19.50 19.25 (3) (1)24 23.75 23.75 23.75 23.75 23.75 (3) 22.75 (3) (1)

GENERAL NOTES(A) The inner ring thickness shall be 0.112 − 0.121 in.(B) For sizes NPS 1 1/4 through NPS 3, the inside diameter tolerance is ± 0.03 in.; for larger sizes the inside diameter tolerance is ± 0.06 in.

NOTES(1) There are no Class 400 flanges NPS 1/2 through NPS 3 (use Class 600), Class 900 flanges NPS 1/2 through NFS 2 1/2 (use Class 1500), or Class

2500 flanges NPS 14 and larger.(2) The inner ring inside diameters shown for NPS 1 1/4 through NPS 2 1/2 in Class 1500 and 2500 will produce inner ring widths of 0.12 in., a

practical minimum for production purposes.(3) Inner rings are required for Class 900, NPS 24 gaskets; Class 1500, NPS 12 through NPS 24 gaskets, and Class 2500, NPS 4 through NPS 12

gaskets.

JUNTAS ESPIROMETÁLICAS / ASME B16.20SPIRAL-WOUND GASKETS / ASME B16.20

Page 72: Esparragos y Tornillos Catalogo Tecnico

71DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

COLOR CODING AND ABBREVIATIONS FOR SPIRAL-WOUND GASKET MATERIALSCODIGO DE COLORES Y ABREVIACIONES PARA LOS MATERIALES DE LAS JUNTAS ESPIROMETALICAS

Material Abbreviation Color Code

Metallic Winding Materials

Carbon Steel CRS Silver

304 SS 304 Yellow

304 L SS 304 L No Color

309 SS 309 No Color

310 S5 310 No Color

316 L SS 316 L Green

347 SS 347 Blue

321 SS 321 Turquoise

430 SS 430 No Color

Ni-CuMonel 400Grade 400

MON Orange

Nickel 200 NI Red

Titanium TI Purple

20 Cb-3 Alloy A-20 Black

Ni-MoHastelloy BGrade B2

HAST B Brown

Ni-Mo-CrHastelloy C

Grade C-276HAST C Beige

Ni-Cr-FeInconel 600Grade 600

INC 600 Gold

Ni-Cr-Fe-CbInconel 625Grade 625

INC 625 Gold

Ni-Cr-Fe-TiInconel X-750Grade X-750

INX No Color

Ni-Fe-CrIncoloy 800Grade 800

IN 800 White

JUNTAS ESPIROMETÁLICAS / ASME B16.20SPIRAL-WOUND GASKETS / ASME B16.20

Page 73: Esparragos y Tornillos Catalogo Tecnico

72DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS RTJ / RING - JOINT GASKETS TYPE R ACCORDING TO ASME B16.20

DIAM. LB # RING N.º

DIMENSIONSdm b h h1

1/21/21/2

300, 60015002500

R 11R 12R 13

34,1339,6842,86

6,357,937,93

11,1114,2614,28

9,5212,712,7

3/43/41

300, 6001500150

R 13R 14R 15

42,8644,4547,62

7,937,937,93

14,2814,2814,28

12,712,712,7

3/41

1 1/4

2500300, 600, 1500150

R 16R 16R 17

50,850,8

57,15

7,937,93 7,93

14,2814,2814,28

12,712,712,7

11 1/41 1/2

2500300, 600, 1500150

R 18R 18R 19

60,3260,3265,08

7,937,937,93

14,2814,2814,28

12,712,712,7

1 1/21 1/4

2

300, 600, 15002500150

*R 20R 21R 22

68,2672,2382,55

7,9311,117,93

14,2817,4614,28

12,715,8712,7

1 1/222

2500300, 6001500

*R 23*R 23*R 24

82,5582,5595,25

11,1111,1111,11

17,4617,4617,46

15,8715,8715,87

2 1/22

2 1/2

1502500300, 600

R 25*R 26*R 26

101,6101,6101,6

7,9311,1111,11

14,2817,4617,46

12,715,8715,87

2 1/22 1/2

3

15002500150

*R 27R 28R 29

107,95111,12114,3

11,1112,77,93

17,4619,0514,28

15,8717,4612,7

−33

−300, 600, 9002500

R30R 31R 32

117,47123,82127,0

11,1111,1112,7

17,4617,46,19,05

15,8715,8717,46

3 1/23 1/2

3

150300, 6001500

R 33R 34*R 35

131,76131,76136,52

7,9311,1111,11

14,2817,4617,46

12,715,8715,87

444

150300, 400, 600, 9002500

R 36R 37R 38

149,22149,22157,6

7,9311,1115,87

14,2817,4622,22

12,715,8720,64

455

1500150300, 400, 600, 900

*R 39R 40*R 41

161,92171,45180,97

11,117,93

11,11

17,4614,2817,46

15,8712,7

15,87565

25001501500

R 42R 43*R 44

190,5193,67193,67

19,057,93

11,11

25,414,2817,46

23,8112,7

15,87666

300, 400, 600, 90015002500

*R 45*R 46*R 47

211,13211,13228,6

11,1112,7

19,05

17,4619,0525,4

15,8717,4623,81

888

150300, 400, 600, 9001500

R 48*R 49*R 50

247,65269,87269,87

7,9311,1115,87

14,2817,4622,22

12,715,8722,64

81010

2500150300, 400, 600, 900

R 51R 52*R 53

279,4304,8

323,85

22,227,93

11,11

28,5714,2817,46

26,9912,7

15,87101012

15002500150

*R 54R 55R 56

323,85342,9381,0

15,8728,577,93

22,2236,5114,28

20,6434,9212,7

OVAL OCTOGONAL

Dimensions in mm.

DIAM. LB RING N.º

DIMENSIONSdm b h h1

121214

300, 400, 600, 9001500150

*R 57R 58R 59

381,0381,0

396,87

11,1122,227,93

17,4628,5714,28

15,8726,9912,7

121414

2500300,400,600900

R 60R 61R 62

406,4419,1419,1

31,7511,1115,87

39,6817,4622,22

38,115,8720,64

141616

1500150300, 400, 600

*R 63R 64*R 65

419,1454,03469,9

25,47,93

11,11

33,3314,2817,46

31,7512,7

15,87161818

9001500150

*R 66R 71R 68

469,9533,4

517,52

15,8728,577,93

22,2236,5114,26

20,6434,9212,7

181818

300, 400, 6009001500

*R 69*R 70R 71

533,4533,4533,4

11,1119,0528,57

17,4625,4

36,51

15,8723,8134,92

202020

150300, 400, 600900

R 72*R 73*R 74

558,8584,2584,2

7,9312,7

19,05

14,2819,0525,4

12,717,4623,81

202424

1500150300, 400, 600

R 75R 76R 77

584,2673,1

692,15

31,757,93

15,87

39,6614,2822,22

38,112,7

20,64242422

9001500150

R 78R 79R 80

692,15692,15615,95

25,434,927,93

33,3344,45

31,7541,2712,7

222630

300, 400, 600300, 400, 600300, 400, 600

R 81R 93R 95

635,0749,3

857,25

14,2819,0519,05

19,0523,8123,81

3436

300, 400, 600300, 400, 600

R 97R 98*R 82

965,21022,3557,15

22,2222,2211,11

26,9826,9815,87

*R 84*R 85*R 86

63,579,3790,49

11,1112,7

15,87

15,8717,4620,63

*R 87*R 88*R 89

100,01123,83114,3

15,8719,0519,05

20,6323,8123,81

*R 90*R 91*R 92

155,58260,35228,6

22,2231,7511,11 17,46

26,9838,0115,87

2832

300, 400, 600300, 400, 600

R 94R 95R 99

800,1914,4

234,95

19,0522,2211,11

23,8126,9815,87

262830

900900900

R 100R 101R 102

749,3800,1

857,25

28,5731,7531,75

34,9238,138,1

323416

900900900

R 103R 104R 105

914,4965,2

1022,35

31,7534,9234,92

38,141,2741,27

(*) Indicate ring N,º accorging to API, STD, 6A

b±0,2 dm±0,18

h±0,4

b±0,2

dm±0,18

h1±0,423ºb±0,2 dm±0,18

h±0,4

b±0,2

dm±0,18

h1±0,423º

Page 74: Esparragos y Tornillos Catalogo Tecnico

73DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS ESPIROMETÁLICAS

GENERALIDADESLas Juntas Espirometálicas están formadas por un fleje metálico en forma de espiral que arrolla un material de relleno. Además puede llevar anillos metálicos de diferentes calidades.

TIPOS BÁSICOS DE JUNTAS ESPIROMETÁLICAS

1. SIN ANILLOS Se utilizan para equipos con espacio y peso Iimitados.

2. CON ANILLO INTERIOR Se usan para llenar el espacio entre las bridas evitando turbu-

lencias en el fluido, o como protección contra la corrosión o la erosión. También se utiliza como limite de compresión cuando la presión es mayor de 172 Mpa.

3. CON ANILLO EXTERIOR Este anillo refuerza la junta y la centra respecto de la brida.

4. CON ANILLOS INTERIOR Y EXTERIOR La utilización de dos anillos garantiza el centrado de la junta y

actúa protegiendo a la misma de la corrosión y la erosión. Se usan para servicios de alta presión y Tª, o cuando el medio de trabajo es corrosivo o tóxico.

5. LOW STRESS Se diferencian de las juntas espirometálica estándar en que el

ancho del fleje es menor, por lo que el material del relleno sobre-sale un poco, pudiéndose realizar el asentamiento de las bridas con tornillería de baja resistencia. En cuanto al resto de las pro-piedades mecánicas no difiere de las juntas normales.

Page 75: Esparragos y Tornillos Catalogo Tecnico

74DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS ESPIROMETÁLICAS

FLEJEEl fleje estandarizado tiene un espesor de 0.15 mm. Los materiales más usuales del fleje son:

- AISI-304 / AISI-304L - MONEL - AISI-316 / AISI-316L - NIKEL 200 - AISI-321 - INCONEL - AISI-347

PRODUCTO DE RELLENOLa estanqueidad de la junta espirometálica está garantizada por el material de relleno y es necesario que esté nivelado con el fleje, nunca por debajo. Los materiales más usuales son los siguientes:

GRAFITOBaja permeabilidad, estabilidad térmica, baja deformación y resistencia química. Rango de Tª de -200 °C a 3000 °C. Apto para servicio con ácidos orgánicos e inorgánicos y con bases, disolventes, aceites y parafinas. No se recomienda su uso para servicios en ambientes de gran oxidación, ya que a partir de 350 °C el material se degrada. En estos casos es necesario proteger el grafito del contacto directo con el medio.El grafito puede utilizarse son O2 en cualquier concentración hasta 500 °C siempre que la junta quede completamente envuelta o protegida entre las bridas.El límite de Tª para uso con vapor de agua e hidrocarburos ricos en hidrógeno es de 650 °C, siempre que el anillo exterior de la junta quede en contacto con el aire. La juntas espirometálicas con grafito tienen mayor tolerancia a los cambios de Tª y presión que las de fibra sintética.

PTFEEste material se utiliza para servicios de alta resistencia química, para r superior a 260 °C. Las juntas de PTFE suelen llevar un anillo interior para aumentar su resistencia mecánica.

FIBRA SINTÉTICATiene buena resistencia al agua, vapor de agua, sustancias alcalinas, soluciones salinas y gases, excepto el O2.

ANILLO EXTERIORNormalmente, el anillo exterior es de acero carbono (AISI 1010/1020) tincado o pintado con un producto para evitar la corrosión. Sin embargo para servicios muy agresivos se utilizan del mismo material que el fleje de la junta.

ANILLO INTERIORPara servicios de alta presión es necesario el uso del anillo interior que reduce la turbulencia en el área de la brida. Normalmente es de la misma calidad que el fleje de la junta. También se utiliza cuando está en contacto con fluidos corrosivos. Cuando el servicio se realiza con Ácido Fluorhídrico (HF) el anillo interior se coloca de PTFE con el fin de proteger la junta y la superficie de la brida. Algunas juntas de grafito tienen tendencia a la deformación, en cuyo caso también se recurre a la colocación del anillo interior.

Page 76: Esparragos y Tornillos Catalogo Tecnico

75DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS ESPIROMETÁLICAS

DISEÑO DE JUNTAS ESPIROMETÁLICASLas junta espirometálica para bridas que no está estandarizada debe diseñarse de forma que la parte del fleje y el relleno no sea menor que el diámetro interior de la brida ni mayor que el diámetro exterior, ya que podría romperse. Por otro lado se diseñará de forma que al ser sometida a una presión de 30000 psi, la junta reduzca su espesor hasta un valor de 3.30 mm ±0.13.

NORMATIVALa Norma ASME B16.20 de Juntas se creó para bridas ANSI B16.5 o ASME/ANSI B 16.47 (API 605 y MSS SP-44). Por eso, a la hora de definir una junta espirometálica solo se deberá hacer referencia al material y al diámetro nominal y presión de la brida.

CONSTRUCCIÓNPara construir una junta espirometálica se deben considerar los siguientes puntos:

- En primer lugar se realizan tres pliegues o vueltas de fleje sin relleno. Los dos primeros pliegues se solda-rán con un mínimo de tres puntos de soldadura a una distancia máxima uno de otro de 3” (76.2 mm).

- El exterior de la espiral contará con un mínimo de tres vueltas de fleje sin relleno soldadas de igual modo, con un mínimo de tres puntos de soldadura, siendo la distancia entre el primer punto y el último menor de 1 1/2” (38 mm).

- El espesor de la espiral de de 4.45 mm más o menos.

INICIO DE BANDA

MÁX. 3”

PUNTOS DE SOLDADURA DISTRIBUIDOSCIRCUNFERENCIALMENTE EN EL INTERIOR

PUNTOS DE SOLDADURA DISTRIBUIDOSCIRCUNFERENCIALMENTE EN EL EXTERIOR

ÚLTIMO PUNTO DE SOLDADURA(Terminal weld)

PRIMER PUNTO DE SOLDADURA(First weld)

MÁX. 1,5”

Page 77: Esparragos y Tornillos Catalogo Tecnico

76DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS ESPIROMETÁLICAS

USO DEL ANILLO INTERIOR EN JUNTAS ESPIROMETÁLICASHay ciertos casos para los que el uso de anillo interior en las juntas espirometálicas es obligado, tal como nos indica la ASME B16.20. Esos casos son los siguientes:

1. Cuando el material de relleno es PTFE 2. Para diámetros de 24” y superiores en 900# 3. Para diámetros de 12” y superiores en 1500# 4. Para diámetros de 4” y superiores en 2500#

El espesor del anillo interior es de 0.112 - 0.131 pulgadas (2.84 - 3.32 mm).

IDENTIFICACIÓNLa identificación de la junta espirometálica se realizará en el anillo de la misma, con letras no mayores de 0.1” (2.54 mm). La información a marcar será la siguiente:

- Nombre del fabricante - Diámetro y presión de la brida - Abreviación del material de relleno - Abreviación del material del fleje - Abreviación del material del anillo, excepto cuando este es de acero carbono para el anillo exterior y

AISI-304 para el interior, en cuyos casos podrá omitirse esta marca - Identificación para el caso de bridas ASME B 16.47

CÓDIGO DE COLORESEl borde del anillo exterior se pinta para ayudar a la identificación de las juntas. La identificación del mate-rial del fleje se pinta con trazo continuo en el borde del anillo exterior y el material del relleno se identifica mediante un mínimo de cuatro trazos espaciados equitativamente también en el borde de dicho anillo.

Page 78: Esparragos y Tornillos Catalogo Tecnico

77DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS RTJ

GENERALIDADESLas Juntas RTJ se diseñaron para su uso en la Industria del Petróleo donde se trabaja con altos valores de Tª y presión, su diseño y descripción se recogieron según la Norma API 6A, aunque hoy en día se fabrican de acuerdo a la Norma ASME B16.20 con dos configuraciones principales diferentes: oval y octogonal.Originalmente las juntas metálicas eran de sección oval y después se desarrolló la RTJ de sección octogo-nal que tiene una eficacia de sellado superior. Para que la estanqueidad sea máxima la superficie de la brida debe ser lo más lisa posible, sin rugosidades ni marcas de herramienta (63 RMS máx.)Bajo presión axial la RTJ de deforma plásticamente y sella las irregularidades de la superficie de contacta, por lo que el material de la junta debe ser siempre más blando que el de la brida. Para las juntas metálicas la recuperación es muy escasa. El sellado se produce por la acción de la carga axial sobre la junta.Las juntas RTJ deben construirse a partir de una sola pieza sin soldaduras, ya que en esta zona la dureza del material es diferente. Cuando son de hierro dulce o acero carbono pueden ir zincadas con un espesor de 0.05 - 0.15 mm.

APLICACIONES- Equipos de perforación y extracción - Válvulas de líneas de “piping”- Válvulas de presión - Plantas químicas y gaseoductos

DIMENSIONESLas juntas RTJ se identifican con una terminología que va desde la R11 hasta la R105 y que recogen todos los diámetros según se especifica en el documento adjunto.Existen otros dos tipos de juntas RTJ que se denominan RX y BX (según API STD. 6 A) que se utilizan cuando los valores de presión son mayores de 700 bar.A veces las juntas metálicas pueden estás recubiertas de goma para evitar daños a las bridas cuando se aplica presión, además proporcionan un valor añadido de sellado.

CROSS SECTION RING TYPE STANDARD

OVAL

R

OCTAGONAL

ANSI B 16.20API STD. 6AMSS SP 44B.S. 1560

BX API STD. 6A

RX API STD. 6A

Page 79: Esparragos y Tornillos Catalogo Tecnico

78DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

MATERIAL ASTM/ANSI DIN DUREZA HB Tª (°C)

SOFT IRON 1.1003 90/100 −60 , 500

CARBON STEEL 1.0038 130/180 −40 , 500

SS 304 304 1.4301 130/180 −250 , 550

SS 304L 304L 1.4306 130/190 −250 , 550

SS 316 316 1.4401 130/180 −100 , 550

SS 316L 316L 1.4404 130/190 −100 , 550

SS 316 Ti 316Ti 1.4571 130/190 −100 , 550

SS 321 321 1.4541 130/190 −250 , 550

SS 347 347 1.4550 130/190 −250 , 550

SS 410 410 1.4006 130/170 650

F5 F5 1.7362 130/170 650

ALUMINIO 3.0255 20/25 −250 , 300

COBRE 2.0090 50/80 −250 , 400

NÍQUEL N 02200 2.4066 90/120 −250 , 600

MONEL 400 N 04400 2.4630 110/150 −125 , 600

INCOLOY 800 N 08800 1.4876 140/220 −100 , 850

HASTELLOY C276 N 10276 2.4819 170/230 −200 , 450

TITANIO 3.7025 110/140 −250 , 350

DUPLEX A182-F53 1.4469 220/290 −50 , 300

MATERIALES USADOS PARA LA FABRICACIÓN DE JUNTAS RTJ

Page 80: Esparragos y Tornillos Catalogo Tecnico

79DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS TÓRICAS

GENERALIDADESLas Juntas Tóricas son elementos de estanqueidad de sección circular.Dada la sencillez de su diseña, así como la simplicidad de su montaje, se han convertido en una solución de estanqueidad frecuentemente adoptada por el diseñador de maquinaria.La denominación normalizada se presenta expresando tan solo el diámetro interior y el de la sección, por este orden.

La junta tórica presenta como ventajas- su reducida sección longitudinal que permite pequeños espacios de montaje- su facilidad de introducción en dicho espacio- su reducido coste

MATERIALES

NITRILO VITON SILICONA ETILENO PROPILENO POLIURETANO

Dureza (Shore A) 70 70-90 70 60 70 84 - 98

Resist. abrasión Excelente Excelente Suficiente Buena 5 veces más que el nitrilo

Tª admisible+100

30+200−10

+200−60

+140−40

+80−20

Resist. Aceite mineral Excelente Excelente Buena Escasa Excelente

Resist. al vapor Suficiente Buena Suficiente Excelente Escasa

Resist. a la acción solar y la oxidación

Buena Buena Excelente Excelente Buena

∅ d

0

∅ d1

Page 81: Esparragos y Tornillos Catalogo Tecnico

80DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS METALOPLÁSTICAS

GENERALIDADESLas juntas metaloplásticas están formadas por una alma de material blando que puede ser fibra sintética libre de amianto, PTFE, grafito, etc. con gran compresibilidad y que soporta altas presiones y tempe-raturas y recubierta parcial o totalmente por una lámina metálica. La calidad del metal debe escogerse teniendo en cuenta la presión de trabajo y el fluido con el que estará en contacto. La combinación de ambos materiales configura una junta resistente y muy apropiada para su uso en la industria petroquími-ca principalmente.Estas juntas pueden ser construidas con uno o varios nervios dispuestos con diferentes configuraciones. Estos nervios pueden ir soldados a la junta principal o construidos formando una sola pieza con la misma, aunque se recomienda que el ángulo de unión tenga un radio de 3/8” en las intersecciones.

DIMENSIONESEl espesor de las juntas metaloplásticas suele ser de 3.2 mm (1/8”) aunque existe la posibilidad de fabricarlas en otros espesores. La dimensiones son ilimitadas (pueden ajustarse al estándar API, ANSI, DIN...) o no, ya que dependen del diseño del equipo en el que se instalarán. Cuando las dimensiones son superiores a la lámina de origen, su fabricación se realiza mediante soldaduras.

APLICACIONES- Intercambiadores de calor- Válvulas de presión- Bocas de hombre- Industria Petroquímica en general

MATERIALESMetal exterior Relleno

- Cobre - Fibra sintética- Aluminio sin asbestos- AISI-304 - Grafito- AISI-316 - PTFE- ASISI-321- AISI-347 - Hierro dulce - Titanio- Níquel- Monel- Inconel

A

AH±0.8

B±0.

8 C±0.8

R±0.8

A±0.

8

ID±0

.8

OD

±0.8

±0.3

Sez. AA

S

IB±0

.8

Page 82: Esparragos y Tornillos Catalogo Tecnico

81DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS METALOPLÁSTICAS

DISEÑOCómo consultar o pedir una junta metaloplástica:

- Diámetro exterior- Diámetro interior- Espesor- Calidad de los materiales- Anchura de Ios nervios- Plano de la junta

10 11 12 13 14 15 16 17 18

19 20 21 22 23 24 25 26 27

28 29 30 31 32 33 34 35 36

37 38 39 40 41 42 43 44 45

46 47 48 49 50 51 52 53

54 55 56 57 58 59 60 61

62 63 64 65 66 67 68

Page 83: Esparragos y Tornillos Catalogo Tecnico

82DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS DIELÉCTRICAS

GENERALIDADESLas líneas o sistemas de tubería (pipeline) que se instalan para el transporte de agua, gas, etc. necesitan una protección extra contra la corrosión externa. Ciertos factores de la naturaleza, fugas de instalacio-nes eléctricas y las reacciones electro-químicas de la tierra producen un efecto de deterioro sobre estas líneas. La experiencia de los últimos años ha demostrado que la protección catódica es una solución eficaz y económica a este problema.Las juntas aislantes juegan un papel importante reduciendo el coste de los sistemas de protección cató-dica en aquellos lugares donde se requiere su instalación.

DIMENSIONESLas juntas aislantes se fabrican según ANSI, BS, DIN y otras especificaciones del cliente. Cada conjunto dieléctrico se compone de:

- 1 junta plana central de espesor 3 mm o una RTJ de sección oval- 1 casquillo aislante de 0.8 mm de espesor de pared por cada espárrago- 2 arandelas aislantes de espesor 3 mm por cada espárrago. El diámetro interior de las arandelas será

diseñado de forma que permitan el deslizamiento de los casquillos a través de las mismas.- 2 arandelas metálicas de 3 mm de espesor por cada espárrago. El diámetro interior será como en el

caso anterior.

APLICACIONES- Reducción del coste de los sistemas de protección catódica en zonas donde son frecuentes las

tormentas eléctricas- Aislar la línea de tubería de forma que no se produzca un aumento de la corrosión o una situación de

riesgo.

MATERIALESJunta central planaResina aislante (fenólica, etc.), puede llevar una capa de neopreno o un refuerzo de fibra sintética libre de amianto.Junta central RTJResina aislante (fenólica, etc.)Casquillos y arandelas dieléctricosResina aislante (fenólica, etc.)Espárragos y arandelas metálicasAcero al carbono

One 1/8” thickplated steelwasher foreach nut

One insulatingwasher foreach nut

One full lengthinsulatingsleeve for eachbolt

One insulatingwasher foreach nut

One 1/8” thickplated steelwasher foreach nut

1/8” thickinsulatinggasket

Page 84: Esparragos y Tornillos Catalogo Tecnico

83DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS PLANAS CON BORDE METÁLICO PROTECTOR

GENERALIDADESNormalmente, para bridas de válvulas, bombas o tubos se utilizan juntas tipo RF de fibra sintética li-bre de amianto, pero en condiciones particulares de presión y temperatura y en contacto con fluidos agresivos la vida de la junta se reduce. En estos casos se utiliza una junta (RF o FF) con un refuerzo metálico que bordea el diámetro interior de la misma, que está en contacto directo con el fluido. Este revestimiento consiste en una fina lámina de acero inoxidable de espesor 0,15 - 0,20 mm curvado en forma de U y prensado sobre la junta plana formando una unidad. El elevado grado de maleabilidad confiere al acero inoxidable excelentes propiedades contra la erosión y la corrosión, así como una buena resistencia al calor.

DIMENSIONESEstas juntas se fabrican de acuerdo a la norma ANSI B16.21 y DIN 2690.

MATERIALESEl material de la junta es de fibra sintética libre de asbestos o de grafito para condiciones de temperatura alta y el refuerzo metálico es de acero inoxidable. Normalmente, hasta diámetro 12” (DN 300) el refuerzo metálico se hace de una sola pieza y para diámetros superiores se fabrica con soldadura.

Page 85: Esparragos y Tornillos Catalogo Tecnico

84DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS KAMMPROFILE (GROOVED)

GENERALIDADESLas juntas Camprofile ofrecen la mayor garantía de sellado comparadas con otros tipos de juntas. Están formadas por una parte metálica circular corrugada que puede llevar incorporado un anillo de la misma calidad que hace la función de centrado de la junta. Este anillo puede estar integrado con la junta o ser móvil. La parte corrugada puede estar recubierta por cada lado de una capa de material más blando.

MATERIALESLa parte metálica de la junta puede ser de acero al carbono, acero inoxidable o materiales exóticos como el Inconel, Monel, etc.

El material blando que recubre la junta puede ser:

- Grafito: excelente resistencia a la corrosión y a la temperatura.- PTFE: para aplicaciones de inactividad química extrema.- Fibra sin asbestos.- Soft iron: pueden utilizarse varias calidades, incluyendo aluminio y plata.

Page 86: Esparragos y Tornillos Catalogo Tecnico

85DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

JUNTAS CORRUGADAS

GENERALIDADESLas juntas corrugadas son apropiadas para su uso en bridas de superficie irregular y trabajos a baja presión. Se fabrican en varias calidades y espesores de lámina metálica. Estas juntas pueden ir recubiertas por una amplia gama de materiales con el fin de abarcar más campos de aplicación.

MATERIALESLa chapa metálica corrugada puede ser de diversas calidades de acero.

El material blando que en ocasiones recubre la junta puede ser:

- Grafito- PTFE- Fibra sin asbestos

Page 87: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

86DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

Datos técnicos

Page 88: Esparragos y Tornillos Catalogo Tecnico

87DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para tornillería - DIN - ISO 898.1 / EN 20898-2NORMAS DE CALIDAD

Estimando de gran interés el conocimiento por parte de nuestros clientes, de las normas por las que se rigen nuestras fabricaciones, es por lo que extractamos a continuación las normas ISO.898.1 y EN-20898-2, que trata de las condiciones técnicas de suministro de tornillos y tuercas.

EJECUCIÓNLa ejecución de la tornillería comercial, corresponde a la calidad m (media).

TOLERANCIA DE ROSCASLas zonas de tolerancia para tornillos y tuercas comerciales son: Tornillo, 6g - Tuerca, 6 H.

ISO 898.1 TORNILLERÍA

SISTEMA DE DESIGNACIÓNEl sistema de designación para la clase de resistencia es como sigue:La designación consta de dos números separados por un punto. El primer número indica 1/10 de la resis-tencia a la tracción en kg/mm2.

Primer número 5 8 10 12

Resistencia a la tracción mínimaσB Kg/mm2 50 80 100 120

El segundo número indica el décuplo de la relación entre el límite de fluencia mínimo y la resistencia a la tracción mínima.

Segundo número 6 8 9

Límite de fluencia mínimo σsResistencia a la tracción mínima σB

10 6 8 9

El producto de ambos números da el límite de fluencia mínimo en kgs/mm2.

PROPIEDADES MECÁNICASEn la tabla siguiente se indican las propiedades mecánicas coordinadas a las clases de resistencia y que sirven para tornillos terminados.

Page 89: Esparragos y Tornillos Catalogo Tecnico

88DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para tornillería ISO 898.1NORMAS DE CALIDAD

a- Para los pernos de clase de calidad 8.8 de diámetros d ≤ 16 mm, existe un gran riesgo de arranque de la rosca de la tuerca en el caso de un apriete excesivo inadvertido, que provoque una carga mayor que la carga de prueba. Se recomienda ver la Norma ISO 898-2 a este respecto.

b- Se aplica únicamente a los diámetros nominales de rosca d ≤16 mm.c- Para los elementos de fijación destinados a estructuras metálicas, el limite es 12 mm.d- Las características mínimas de resistencia a la tracción se aplican a los productos de longitud nominal l ≥ 2,5 d. La dureza mínima es válida para productos de longitud

l < 2,5 d y para otros productos que no se pueden someter a ensayos de tracción (por ejemplo, debido a la configuración de la cabeza).e- Cuando se ensayan pemos, tomillos y burlones enteras, las cargas de rotura aplicables para el cálculo de Rm deben cumplir los valores que se dan en las tablas 6 y 8 (ISO 898.1).f- Una medida de dureza efectuada en el extremo de los pernos. tomillos y bulones debe ser de 250 HV, 238 HB o 99,5 HRB, como máximo.g- La dureza superficial no debe ser mayor que 30 puntos Vickers por encima de la dureza medida del núcleo central del producto, cuando ambas mediciones se realizan con HV

0,3. Para la clase de calidad 10.9, cualquier aumento de la dureza superficial que indique que ésta supera los 390 HV es inaceptable.h- En los casos en que el límite elástico inferior R eL no se pueda determinar, se permite medir el limite elástico convencional al 0,2%, R p0,2 Para las clases de calidad 4.8, 5.8 y

6.8, los valores de R eL se dan únicamente para las necesidades de cálculo, no son valores de ensayo.i- La relación de límite elástico aparente, tal como se define en la designación de la clase de calidad, así como el limite elástico convencional al 0,2%, R p0,2, se obtienen a partir

de medidas efectuadas sobre probetas. Cuando estas medidas se obtienen a partir de medidas efectuadas sobre pernos y tomillos completos, variarán debido a los efectos del tamaño y del método de fabricación.

Apar-tadonº

Característica mecánica y física

Clase de calidad

3.6. 4.6 4.8 5.6 5.8 6.8 8.8 a 9.8 b 10.9 12.9d ≤ 16c

mmd > 16c

mm

5.1 Resistencia nominal a la tracción, R m, nom N/mm2 300 400 500 600 800 800 900 1.000 1.200

5.2. Resistencia mínima a la tracción, R m, mín. d,e N/nm2 330 400 420 500 520 600 800 830 900 1.040 1.220

5.3Dureza Vickers, HV

F ≥98 N

mín. 95 120 130 155 160 190 250 255 290 320 385

máx. 220f 250 320 335 360 380 435

5.4Dureza Brinell, HB

F =30 D2

mín. 90 114 124 147 152 181 238 242 276 304 366

máx. 209f 238 304 318 342 361 414

5.5 Dureza Rockwell, HR

mín. HRB 52 67 71 79 82 89

HRC 22 23 28 32 39

máx. HRB 95,0F 99,5

HRC 32 34 37 39 44

5.6 Dureza superficial, HV 0,3 máx. g

5.7 Límite elástico inferior, ReLh, N/mm2nom. 180 240 320 300 400 480

mín. 190 240 340 300 420 480

5.8Límite elástiaco convencional al

0,2%, Rp0,2i, N/mm2

nom. 640 640 720 900 1080

mín. 640 660 720 940 1100

5.9 Tensión a la carga de prueba, Sp

Sp/ReL o Sp/Rp 0,2

0,94 0,94 0,91 0,93 0,9 0,92 0,91 0,91 0,9 0,88 0,88

N/mm2 180 225 310 280 380 440 580 600 650 830 970

5.10 Par de rotura, MB Nm mín. Véase Norma ISO 898-7

5.11 Alargamiento porcentual después de la rotura, A mín. 25 22 20 12 12 10 9 8

5.12Redución de la sección después de la

rotura, Z% mín. 52 48 48 44

5.13Esfuerzo o resistencia a la tracción bajo

carga en cuña e

Los valores para pernos y tornillos (excluidos los bulones) de tamaño completo no deben ser inferiores a los valores mínimos de la resistencia a la tracción indicados en el apartado 5.2.

5.14 Resistencia al impacto, KU J mín. 25 30 30 25 20 15

5.15 Solidez de la cabeza Sin rotura

5.16

Altura mínima de la zona no decarburada de la zona de roscada, E

1/2 H1 _H1 3/4 H1

Profundidad máxima de la descarburación completa, G

mm 0,015

5.17 Dureza después del segundo revenido Reducción de dureza de 20 HV como máx.

5.18 Integridad de superficie De acuerdo con la Norma ISO 6157-1 o la ISO 6157-3, según proceda

Page 90: Esparragos y Tornillos Catalogo Tecnico

89DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

a- El contenido de boro puede alcanzar 0,005% siempre que el boro no eficaz se controle por la adición de titanio y/o de aluminio.

b- Se permite del acero de fácil mecanización para estas clases de calidad con los contenidos máximos de azufre, fósforo y plomo siguientes: azufre 0,34% fósforo 0,11%; plomo 0,35%.

c- Para diámetros nominales mayores de 20 mm pueden ser necesarios los aceros especificados para la clase 10.9 con el fin de lograr una templabilidad suficiente.

d- En el caso de acero aleado al boro con un contenido de carbono inferior al 0,25% (análisis en la cuchara), el contenido mínimo de manganeso debe ser del 0,6%. para la clase de calidad 8.8 y del 0,7% para 9.8, 10.9 y 10.9.

e- Adicionalmente los productos se deben identificar mediante el subrayado del símbolo de la clase de calidad (véase el capítulo 9). Todas las características de la clase 10.9, tales como las especificadas en la tabla 3, deben cumplirse por la clase 10-9; no obstante, debido a su temperatura de revenido más baja, se obtienen características de relajación de tensiones diferentes a altas temperaturas.

f- Para los materiales de estas clases de calidad, se debería intentar que tuviesen una templabilidad suficiente para garantizar una estructura con el 90% aproximadamente de martensita en el núcleo central de las secciones roscadas para los elementos de fijación después del temple y antes del revenido.

g- Este acero aleado debe contener, como mínimo, uno de los elementos siguientes en la cantidad mínima dada: cromo 0,30%, níquel 0,30%, molibdeno 0,20%; vanadio 0,10%. Cuando los elementos se especifican en combinaciones de dos, tres o cuatro y tienen contenidos de aleación inferiores a los citados anteriormente, el valor límite aplicable para la determinación de la clase es el 70% de la suma de los valores límites individuales mostrados ante-riormente para los dos, tres o cuarto elementos respectivos.

h- No se permite una capa enriquecida con fósforo blanco detectable metalográficamente para la clase de calidad 12.9 en superficies sometidas a esfuerzos de tracción.

i- La composición química y la temperatura de revenido se están investigando.

Clase de calidad

Materiales y tratamientos

Límites de la composición química(análisis de comprobación) % (m/m)

Tempe-ratura de revenido

C P S Bª ºC

mín máx. máx. máx. máx. mín.

3.6 b

Acero al carbono

- 0,2 0,05 0,06 0,003 -

4.6 b

- 0,55 0,05 0,060,003 -

4.8 b

5.6 b 0,13 0,55 0,05 0,06 0,003 -

5.8 b

- 0,55 0,05 0,066.8 b

8.8 c

Acero al carbono con aditivos (por ejemplo, B, Mn o Cr) templado y revenido

0,15d 0,4 0,035 0,035 0,003 425

Acero al carbono templado y revenido 0,25 0,55 0,035 0,035

9.8Acero al carbono con aditivos (por ejemplo,

B, Mn o Cr) templado y revenido0,15d 0,35 0,035 0,035 0,003 425

Acero al carbono templado y revenido 0,25 0,55 0,035 0,035

10.9 e f Acero al carbono con aditivos (por ejemplo, B, Mn o Cr) templado y revenido

0,15d 0,35 0,035 0,035 0,003 340

10.9 f

Acero al carbono templado y revenido 0,25 0,55 0,035 0,035 0,003 425

Acero al carbono con aditivos (por ejemplo, B, Mn o Cr) templado y revenido

0,20d 0,55 0,035 0,035

Acero aleado templado y revenidog 0,2 0,55 0,035 0,035

12.9 f h i Acero aleado templado y revenidog 0,28 0,5 0,035 0,035 0,003 380

para tornillería ISO 898.1NORMAS DE CALIDAD

Page 91: Esparragos y Tornillos Catalogo Tecnico

90DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para tuercas UNE - EN 20898-2NORMAS DE CALIDAD

CLASES DE RESISTENCIATuercas.

SISTEMA DE DESIGNACIÓNLas clases de resistencia de las tuercas se designan con un número correspondiendo a 1/10 de la tensión de ensayo en Kg/mm. Esta tensión de ensayo corresponde a la resistencia a la tracción mínima en Kg/mm2 de un tornillo, con el que ha de juntarse la tuerca cuando se ha de garantizar la capacidad de carga de la rotura mínima del tornillo.

MATERIALESLas tuercas se fabricarán de acero en conformidad con los límites de composición química especificados en la siguiente tabla.

Clase de calidad

Límites de composición química(análisis de composición), %

C Mn P S

máx. mín. máx. máx.

41); 51); 61) — 0,500 — 0,060 0,150

8; 9 041) 0,580 0,250 0,060 0,150

102) 052) 0,580 0,300 0,048 0,058

122) — 0,580 0,450 0,048 0,058

1) Las tuercas de estas clases de calidad pueden fabricarse de aceros de fácil mecanización, a menos que se acuerde de otra forma entre el comprador y el fabricante. En tales casos, son admisibles los siguientes contenidos máximos de azufre, fósforo y plomo:

azufre 0,34%; fósforo 0,11%; plomo 0,35%.

2) Pueden añadirse, si es necesario, elementos de aleación a fin de mejorar las características mecánicas de las tuercas.

Page 92: Esparragos y Tornillos Catalogo Tecnico

91DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para tuercas UNE - EN 20898-2NORMAS DE CALIDAD

PROPIEDADES MECÁNICASA continuación se exponen las propiedades mecánicas coordinadas a las clases de resistencia y que sirven para tuercas determinadas.

Rosca

Clase de calidad

04 05 4

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Es-fuerzo

de prueba

Sp

Dureza Vickers

HVTuerca

Mayor que hasta N/mm2 mín. máx.

esta-do

tipo N/mm2 mín. máx.esta-do

tipo N/mm2 mín. máx. estado tipo

M4

380 188 302 NTR1) fina 500 272 353 TR2) fina- - - - -

M4 M7

M7 M10

M10 M16

M16 M39 510 117 302 NTR1) 1

Rosca

Clase de calidad

53) 6 8

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Es-fuerzo

de prueba

Sp

Dureza Vickers

HVTuerca

Es-fuerzo

de prueba

Sp

Dureza Vickers

HVTuerca

Mayor que hasta N/mm2 mín. máx.

esta-do

tipo N/mm2 mín. máx.esta-do

tipo N/mm2 mín. máx. estado tipo N/mm2 mín. máx.esta-

dotipo

- M4 520

130302 NTR1) 1

600

150302 NTR1) 1

800 180

302 NTR1)

1- - - - -

M4 M7 580 670 855

200M7 M10 590 680 870

M10 M16 610 700 880

M16 M39 630 146 720 170 920 233 353 TR2) 890 180 302 NTR1) 2

Rosca

Clase de calidad

9 10 12

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Esfuer-zo de

pruebaSp

Dureza Vickers

HVTuerca

Es-fuerzo

de prueba

Sp

Dureza Vickers

HVTuerca

Es-fuerzo

de prueba

Sp

Dureza Vickers

HVTuerca

Mayor que hasta N/mm2 mín. máx.

esta-do

tipo N/mm2 mín. máx.esta-do

tipo N/mm2 mín. máx. estado tipo N/mm2 mín. máx.esta-

dotipo

M4 900 170

302 NTR1) 2

1 040

272 353 TR2) 1

1 140

295 353 TR2) 1

1 150

272 353 TR2) 2

M4 M7 915

188

1 040 1 140 1 150

M7 M10 940 1 040 1 140 1 160

M10 M16 950 1 050 1 170 1 190

M16 M39 920 1 060 - - - - - 1 200

1) NTR = No templada ni revenida.2) TR = Templada y revenida.3) La dureza máxima de los pernos de clase de calidad 5.6 y 5.8 será reducida a 220 HV en la próxima revisión de la Norma ISO 898-1:1988. Esta es la máxima dureza del perno en la superficie de trabajo de la rosca, donde sólo el extremo (salida) da rosca o la cabeza pueden tener una dureza máxima de 250 HV. Por consiguiente, los esfuerzos de prueba están basados en una dureza máxima del perno de 220 HV.NOTA. La dureza mínima sólo es obligatoria para tuercas tratadas térmicamente y tuercas demasiado grandes para ser sometidas al ensayo de carga de prueba. Para el resto de tuercas, la dureza minima se da sólo a título indicativo. Para tuercas no templadas ni revenidas, y que satisfacen el ensayo de carga de prueba, la dureza minima no deberá ser motivo de rechazo.

Page 93: Esparragos y Tornillos Catalogo Tecnico

92DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

ACEROS INOXIDABLES PARA TORNILLERÍA / ISO 3506STAINLESS STEEL FASTENERS / ISO 3506

COMPOSICIÓN QUÍMICA / CHEMICAL REQUIREMENTS

Material Cmax.

SImax.

Mnmax.

Cr NI P S Mo

A4 0.08 1.0 2.0 16 – 18.5 10 –15 0.05 max. 0.03 2 - 3

A2 0.08 1.0 2.0 17 – 20 8 –13 0.05 max. 0.03 −

A1 0.12 1.0 2.0 17 – 19 5 – 10 0.20 0.15 – 0.35 max. 0.6

PROPIEDADES MECÁNICAS / MECHANICAL REQUIREMENTS

Bolt — Screws — Studs Nuts

GradeProperty

classTensile strengthRm

(1) min. N/mm2

Stress at 0,2% permanent strengthRp 0.2

(1) min N/mm2

ExtensionAL 2 min.

Proof load stress,Sp min. N/mm2

A1 - A2 - A4

50 500 210 0.6 d 500

70 700 450 0.4 d 700

80 800 600 0.3 d 800

(1) All tensile stress values are calculated and reported in terms of the nominal tensile stress area of the thread.

Page 94: Esparragos y Tornillos Catalogo Tecnico

93DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

por laminaciónTÉCNICAS DE ROSCA

La fabricación de DIMECO, S. A., está orientada al roscado por laminación de diversos aceros, tanto inoxi-dables como al carbono.

FUNDAMENTOEn el proceso de roscado por laminación, el material es sometido a un esfuerzo más allá de su límite elás-tico, produciendo una deformación plástica. Este fenómeno, conocido como trabajo en frío, produce en el material un endurecimiento superficial que aumenta sus propiedades mecánicas.

Los metales se componen de granos unidos debido a sus energías superficiales y a uniones geométricas. Cuando el metal está sujeto a deformación en frío, éstos se rompen y alargan en la dirección de la deforma-ción. En la laminación, los granos fluyen a lo largo de los contornos impuestos por el rodillo.

El resultado es que la zona de trabajo en frío es apreciablemente más dura, incrementando las propiedades mecánicas de la zona roscada.

El criterio para laminar un metal es que sea lo suficientemente plástico para que fluya y resista las tensiones del trabajo en frío sin desintegrarse.

Se consideran como materiales laminables todos aquéllos cuyo alargamiento sea del 12 por 100 o mayor, según ASTM A-370.

Hay factores a considerar, como son: dureza, límite elástico, microestructura, módulo de elasticidad, com-ponentes no metálicos del acero, el paso y diámetro de la pieza, etc.

Micrografía de la estructura de fibrade una rosca obtenida por laminación

Page 95: Esparragos y Tornillos Catalogo Tecnico

94DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

por laminaciónTÉCNICAS DE ROSCA

El roscado se puede verificar de dos maneras:

1. Roscado simultáneo o “plongée”.La pieza es introducida entre los rodillos giratorios, uno de los cuales es fijo y es apoyada en una regleta.

Por medio del rodillo móvil se produce la presión necesaria para el laminado de la pieza.

2. Roscado en hilera o enfilada.La pieza, además de girar, tiene un movimiento de traslación, por efecto del especial diseño de los ro-dillos, con un ángulo de inclinación de la rosca de aproximadamente 2/3 del ángulo del tornillo y una entrada conveniente.

Este proceso es apropiado para trabajar piezas roscadas largas y para aquéllas en que el roscado simul-táneo no tiene aplicación por su limitada longitud a roscar.

El roscado por laminación, además de no romper las fibras del material, produce sobre la estructura del mismo presiones que dan origen a unas capas superficiales mucho más duras, tenaces y resistentes al roce que el núcleo o material inicial.

Variaciones de dureza en una rosca obtenida por laminación

440

420

400

380

370

360

350

340

Diámetro interior450

460

470

480

490

500

500

550

600

460

450

460

470

480

490

500

500

550

600

Page 96: Esparragos y Tornillos Catalogo Tecnico

95DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I. B 1.1. class 2A and 2B

ROSCA SERIE ASMEUNC-8UN THREAD

UNC THREAD SERIE ASME B 1.1. class 2A and 2B

BOLTS - EXTERNAL mm NUTS - INTERNAL mm

Nom. Size

ThreadsMajor Diameter Pitch Diameter Minor Major Minor Diameter Pitch Diameter

max. min max. min. max. min. min. max. min. max.1/4 20 6,322 6,116 5,497 5,403 4,765 6,350 4,978 5,258 5,525 5,646

5/16 18 7,907 7,686 6,99 6,888 6,175 7,938 6,401 6,731 7,021 7,1553/8 16 9,492 9,253 8,461 8,349 7,544 9,548 7,798 8,153 8,494 8,639

7/16 14 11,077 10,815 9,898 9,779 8,852 11,113 9,144 9,550 9,934 10,0891/2 13 12,662 12,385 11,392 11,265 10,264 12,700 10,592 11,024 11,430 11,595

9/16 12 14,247 13,957 12,873 12,741 11,651 14,288 11,989 12,446 12,913 13,0865/8 11 15,834 15,527 14,336 14,196 13,002 15,875 13,386 13,868 14,376 14,5593/4 10 19,004 18,677 17,353 17,203 15,888 19,050 16,307 16,840 17,399 17,5957/8 9 22,177 21,824 20,343 20,183 18,715 22,225 19,177 19,761 20,391 20,5991 8 25,349 24,968 23,287 23,114 21,453 25,400 21,971 22,606 23,338 23,561

11/8 7 28,519 28,103 26,162 25,979 24,067 28,575 24,638 25,349 26,218 26,45711/4 7 31,694 31,278 29,337 29,149 27,242 31,750 27,813 28,524 29,393 29,63713/8 6 34,864 34,402 32,113 31,910 29,670 34,925 28,435 31,115 32,174 32,43811/2 6 38,039 37,577 35,288 35,082 32,845 38,100 33,528 34,290 35,349 35,6161 3/4 5 44,387 43,924 41,636 41,425 39,347 44,450 39,878 40,640 41,699 41,974

2 4,5 50,726 50,168 47,061 46,820 43,802 50,800 44,679 45,593 47,135 47,4502 1/4 4,5 57,076 56,518 53,411 53,165 50,152 57,150 51,029 51,943 53,485 53,8052 1/2 4 63,421 62,817 59,296 59,032 55,631 63,500 56,617 57,582 59,375 59,7182 3/4 4 69,769 69,164 65,644 65,377 61,979 69,850 62,967 63,932 65,725 66,073

3 4 76,119 75,514 71,994 71,722 68,329 76,200 69,317 70,282 72,075 72,4283 1/4 4 82,466 81,862 78,341 78,064 74,676 82,550 75,667 76,632 78,425 78,7833 1/2 4 88,816 88,212 84,691 84,412 81,026 88,900 82,017 82,982 84,775 85,1383 3/4 4 95,164 94,559 91,039 90,754 87,373 95,250 88,367 89,332 91,125 91,493

4 4 101,514 100,909 97,389 97,102 93,723 101,600 94,717 95,682 97,475 93,605

8UN THREAD SERIE ASME B 1.1. class 2A and 2B

BOLTS - EXTERNAL mm NUTS - INTERNAL mm

Nom. Size

ThreadsMajor Diameter Pitch Diameter Minor Major Minor Diameter Pitch Diameter

max. min. max. min. max. min. min. max. min. max.1 1/8 8 28,522 28,141 26,459 26,284 24,625 28,575 25,781 25,146 26,741 26,5131 1/4 8 31,697 31,316 29,634 29,456 27,800 31,750 28,956 28,321 29,921 29,6881 3/8 8 34,869 34,488 32,807 32,624 30,973 34,925 32,131 31,496 33,099 32,8631 1/2 8 38,044 37,663 35,982 35,796 34,148 38,100 35,306 34,671 36,279 36,0381 5/8 8 41,219 40,838 39,157 38,969 37,323 41,275 38,481 37,846 39,459 39,2131 3/4 8 44,392 44,011 42,329 42,139 40,495 44,450 41,656 41,021 42,636 42,3881 7/8 8 47,567 47,186 45,504 45,309 43,670 47,625 44,831 44,196 45,817 45,563

2 8 50,742 50,361 48,679 48,481 46,845 50,800 48,006 47,371 48,994 48,7382 1/4 8 57,089 56,708 55,027 54,823 53,193 57,150 54,356 53,721 55,352 55,0882 1/2 8 63,439 63,058 61,377 61,168 59,543 63,500 60,706 60,071 61,707 61,4382 3/4 8 69,787 69,406 67,724 67,513 65,890 69,850 67,056 66,421 68,062 67,788

3 8 76,134 74,229 74,071 73,856 72,238 76,200 73,406 72,771 74,419 74,1383 1/4 8 82,484 82,103 80,421 80,201 78,704 82,550 79,121 79,756 80,488 80,7753 1/2 8 88,834 88,453 86,771 86,548 85,054 88,900 85,471 86,106 86,838 86,1303 3/4 8 95,181 94,800 93,119 92,890 91,402 95,250 91,821 92,456 93,118 93,485

4 8 101,531 101,150 99,469 99,238 97,752 101,600 98,171 98,806 99,538 99,8404 1/4 8 107,879 107,848 105,816 105,580 104,099 107,950 104,521 105,156 105,888 106,1924 1/2 8 114,229 113,848 112,166 111,928 110,449 114,300 110,871 111,506 112,238 112,5474 3/4 8 120,576 120,595 118,514 118,273 116,797 120,650 117,221 117,856 118,588 118,902

5 8 126,926 126,545 124,864 124,617 123,147 127,000 123,571 124,206 124,938 125,258* values in mm

H 8

p8

p2

p4

5H 8

17H 24

p2

H 8

p8

H 4

p

H

Diámetro exteriorTuerca

Línea de paso

60º

Tuerca

60ºLínea de paso

p

Diámetro interior

5H 8H 4

H 8

p8

p2

p4

5H 8

17H 24

p2

H 8

p8

H 4

p

H

Diámetro exteriorTuerca

Línea de paso

60º

Tuerca

60ºLínea de paso

p

Diámetro interior

5H 8H 4

Page 97: Esparragos y Tornillos Catalogo Tecnico

96DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Con perfil triangular / With tringular profile ROSCA MÉTRICA / ISO METRIC THREAD

METRIC THREAD SERIE DIN 13 class 6g and 6H

BOLTS - EXTERNAL mm NUTS - INTERNAL mm

Nom. Size

ThreadsMajor Diameter Pitch Diameter Minor Major Pitch Diameter Minor Diameter

max. min max. min. max. min. min. max. min. max.8 1,25 7,972 7,760 7,160 7,042 6,619 8,000 7,188 7,348 6,647 6,912

10 1,5 9,968 9,732 8,994 8,862 8,344 10,000 9,026 9,206 8,376 8,67612 1,75 11,966 11,701 10,829 10,679 10,072 12,0000 10,863 11,063 10,106 10,44114 2 13,962 13,682 12,682 12,503 11,797 14,000 12,701 12,913 11,835 12,21016 2 15,962 15,682 14,663 14,503 13,797 16,000 14,701 14,913 13,835 14,21018 2,5 17,958 17,623 16,334 16,164 15,252 18,000 16,376 16,600 15,294 15,74420 2,5 19,958 19,623 18,334 18,164 17,252 20,000 18,376 18,600 17,294 17,74422 2,5 21,958 21,623 20,334 20,164 19,252 22,000 20,376 20,600 19,294 19,74424 3 23,952 23,577 22,003 21,803 20,704 24,000 22,051 22,316 20,752 21,25227 3 26,952 26,577 25,003 24,803 23,704 27,000 25,051 25,316 23,752 24,25230 3,5 29,947 29,522 27,674 27,462 26,158 30,000 27,727 28,007 26,211 26,77133 3,5 32,947 32,522 30,674 30,462 29,158 33,000 30,727 31,007 29,211 29,77136 4 35,940 35,465 33,342 33,118 31,610 36,000 33,402 33,702 31,670 32,27039 4 38,940 38,465 36,342 36,118 34,610 39,000 36,402 36,702 34,670 35,27042 4,5 41,937 41,437 39,014 38,778 37,066 42,000 39,077 39,392 37,129 37,79945 4,5 44,937 44,437 42,017 41,778 40,066 45,000 42,077 42,392 40,129 40,79948 5 47,929 47,399 44,681 44,431 42,516 48,000 44,752 45,087 42,587 43,29752 5 51,929 51,399 48,681 48,431 46,516 52,000 46,752 49,087 46,587 47,29756 5,5 55,925 55,365 52,353 52,088 49,971 56,000 52,428 52,783 50,046 50,79660 5,5 59,925 59,365 56,353 56,088 53,971 60,000 56,428 56,783 54,046 54,79664 6 63,920 63,320 60,023 59,743 57,425 64,000 60,103 60,478 57,505 58,30568 6 67,920 67,320 64,023 63,743 61,425 68,000 64,103 64,478 61,505 62,30572 6 71,920 71,320 68,023 67,743 65,425 72,000 68,103 68,378 65,505 66,30576 6 75,920 75,320 72,023 71,743 69,425 76,000 72,103 72,478 69,505 70,30580 6 79,920 79,320 76,023 75,743 73,425 80,000 76,103 76,478 73,505 74,305

D

60º

P

D2

D1

d 3

d 1d 2

d

H

H/2

H/2

60º

H/4 Tornillo

r

H1

Tuerca

H/8

h 2

d2 = D2 = d – 0,6495 Pd3 = d – 1,2268 P

d1 = D1 = d – 1,0825 Pr = 0,1443 P

Page 98: Esparragos y Tornillos Catalogo Tecnico

97DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

INFLUENCIA DE LOS ELEMENTOS QUÍMICOS EN LOS ACEROS

Las aleaciones de acero con diferentes elementos químicos se realizan para mejorar las propiedades físicas y conseguir propiedades especiales:

Carbono (C)Aunque no se considere cono un elemento de aleación, es el más importante componente del acero. Aumenta la resistencia a la tracción, dureza y resistencia a la abrasión. Reduce la ductilidad, rigidez y mecanización.

Manganeso (Mn)Es oxidante y desgasificador y reacciona con el azufre para mejorar la forjabilidad Aumenta la resistencia a la tracción, dureza y durabilidad.

Fósforo (P)Aumenta la resistencia y la dureza y mejora la mecanización. Produce fragilidad en el acero.

Azufre (S)Mejora la mecanización en presencia de manganeso. Reduce la soldabilidad, impacto, rugosidad y ductibiliidad.

Silicio (Si)Es desoxidante y desgasiticador Aumenta la resistencia, elasticidad, dureza y forjabilidad.

Cromo (Cr)Incrementa la resistencia a la rotura, dureza, durabilidad, rugosidad y la resistencia a altas temperaturas.

Níquel (Ni)Eleva la resistencia y la dureza, manteniendo la ductilidad y la rigidez. Aumenta la resistencia al agrietamiento y a elevadas temperaturas.

Molibdeno (Mo)Aumenta La resistencia, dureza, durabilidad y rigidez, así como la resistencia al agrietamiento y a elevadas temperaturas.

Titanio (Ti)Es usado como elemento estabilizador en el acero inox. Tiene gran afinidad por el carbono.

Page 99: Esparragos y Tornillos Catalogo Tecnico

98DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PROPIEDADES DE LOS ACEROS

CALIDAD PROPIEDADES

B6

Buena resistencia en ambiente corrosivo (aceite crudo, petróleo, ácidos orgánicos, disolventes

organices, amoniaco) pero no en medios altamente corrosivos. Buena resistencia a la corrosión

hasta Tª de 650 °C, buena soldabilidad.

B7Buena resistencia y dureza, sobre todo para usos en condiciones de alta Tª (−10°C / +427 °C).

Aplicaciones: Petroquímica, válvulas, bombas.

B7MSimilar al B7 pero con las propiedades mecánicas mas bajas.

Aplicaciones: Industria Petroquímica.

B16Prescrita buena resistencia y dureza en medios de altas Tª (−10 °C / +558 °C).

Aplicaciones: Industria Petroquímica.

B8 (A-193)

Utilizado para Tª entre −196°C y + 538 °C. Buena resistencia a la corrosión intercristalina y

excelente soldabilidad. Aplicaciones: Petroquímica., química, farmacéutica, alimentación,

carpintería.

B8 (A-320)Buena resistencia a la corrosión. Adecuado para usos a baja Tª (−254 °C / + 50 °C).

Aplicaciones: Industria química, farmacéutica y de alimentación.

B8M (A-193)Excelente resistencia a la corrosión intercristalina y a la corrosión causada por iones de Cl.

Rango de Tª (−196 °C/ + 538 °C).

B8M (A-320)Buena resistencia a la corrosión. Indicado para Tª entre −196 °C y + 50°C).

Aplicaciones: Industria química y petroquímica.

B8C (A-193)

Alta resistencia a la corrosión intergranular y al la oxidación. Se utiliza para Tª (−196 °C / +538 °C).

Aplicaciones: Industria petroquímica, cambios de Tª y para construcción de estructuras para

plantas químicas.

B8C (A-320)Buena resistencia a la corrosión. Indicado par Tª (−254 °C/ + 50 °C).

Aplicaciones: Industria química y petroquímica.

B8T (A-193)

Indicado para rango de Tª (−196 °C / + 538 °C). Alta resistencia a la corrosión intergranular

gracias a la presencia del Titanio. Buena soldabilidad sin necesidad de tratamiento térmico

adicional. Aplicaciones: Industria petroquímica, química, alimentación y plantas de generación

de energía.

B8T (A-320) Usado para Tª (−101 ºC /+50 °C). Aplicaciones: Industria petroquímica

B5 Para uso en condiciones de alta Tª. Aplicaciones: Industria petroquímica, válvulas y bridas.

Page 100: Esparragos y Tornillos Catalogo Tecnico

99DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PROPIEDADES DE LOS ACEROS

CALIDAD PROPIEDADES

GR.660Excelentes propiedades mecánicas para uso a alta Tª.

Aplicaciones: equipos de presión y bridas.

L7Buena resistencia y dureza, excelente para uso a baja Tª (−101 “C / + 50 °C).

Aplicaciones: Industria petroquímica.

L7MSimilar al L7 pero con propiedades mecánicas mas bajas.

Aplicaciones: Industria petroquímica.

Monel 400

Alta resistencia, buena soldabilidad, perfecta resistencia a la corrosión bajo un amplio rango de

Tª y condiciones (agua marina, acidez minerales y orgánicos).

Aplicaciones: Válvulas, bombas, instalaciones marinas, plantas petroquímicas, cambios de

temperatura y para usos en contacto con ácidos sulfúrico y fluorhídrico.

Monel 500Resistencia mecánica y resistencia a la abrasión mayores que el Monel 400.

Aplicaciones: Válvulas, bombas, plantas petroquímicas y elementos de unión.

Inconel 600

Excelente resistencia en ambientes tanto oxidantes como reductores, así como en ambientes

corrosivos a altas Tª.

Aplicaciones: Equipos para industria química, textil y de alimentación, hornos.

Inconel 625

Gran resistencia mecánica desde Tª criogénicas hasta muy altas Tª (1100 °C).

Excelente resistencia a la fatiga y la oxidación.

Aplicaciones: Industria química, equipos marinos, conductos y válvulas.

Incoloy 800H

Resistencia a la corrosión y a la carburización a elevadas Tª (hasta 1100 °C).

Resistente al ataque de los sulfuros, a la corrosión y al decapado.

Aplicaciones: cambios de Tª, equipos de calor, generadores.

Incoloy 825

Excelente resistencia a la rotura por efecto de la corrosión, resistente en ambientes oxidantes

y reductores.

Aplicaciones: tanques para desoxidar, industria química, sistemas de control de la polución.

Hastelloy C276

Buena resistencia a la rotura por efecto de la corrosión en presencia de compuestos de cloro,

resistencia a la corrosión intercristalina. Aplicaciones: empleado en ambientes con procesos

químicos severos, en la industria papelera y de control de la polución.

Duplex 2205Muy alta resistencia a la rotura por corrosión.

Aplicaciones: industria química y del aceite, tuberías, bridas, válvulas para usos a elevadas Tª.

Superduplex

32760

Perfecta resistencia a la corrosión intersticial y a ambientes corrosivos.

Aplicaciones: instalaciones marinas y plantas petroquímicas.

Page 101: Esparragos y Tornillos Catalogo Tecnico

100DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PRODUCTOS METÁLICOS UNE-EN 10204:2006Tipos de documentos de inspección

Referencia de la Norma Europea

EN 10204

Designación del tipo de documento

Contenido del documento Documento validado por

Tipo 2.1 Declaración de conformidad con el pedido

Declaración de conformidad con el pedido

El fabricante

Tipo 2.2 Informe de ensayo Declaración de conformidad con el pedido, con indicaciones de los resultados de una inspección no específica

El fabricante

Tipo 3.1 Certificado de Inspección 3.1 Declaración de conformidad con el pedido, con indicación de los resultados de una inspección específica

El representante autorizado por el fabricante para la inspección, independiente del departamento de fabricación

Tipo 3.2 Certificado de Inspección 3.2 Declaración de conformidad con el pedido, con indicación de los resultados de una inspección específica

El representante autorizado por el fabricante para la inspección, independiente del departamento de fabricación, y por el representante autorizado por el comprador para la inspección o por el inspector designado en las regulaciones oficiales

Page 102: Esparragos y Tornillos Catalogo Tecnico

101DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PAR DE APRIETE EN LAS UNIONES ATORNILLADASIMPORTANCIA DE LA FUERZA DE PRETENSADO Y DEL

Deseamos facilitarle una serie de datos que le serán de gran utilidad, aunque en ocasiones especiales tengan que recurrir a estudios más profundos, pero que para la mayor parte de los casos que se le pueden presentar, con la tabla que sigue y una aplicación correcta del par de apriete por medio de llaves dinamométricas, le serán suficientes.

No obstante creemos conveniente ampliar algunos conceptos importantes.

Una unión atornillada forma un sistema más o menos complejo; función de los órganos a unir, de las calidades de los materiales, de que exista o no lubricación entre ellos y entre los elementos de tornillo de sujeción y tuerca...

La conclusión derivada será lógicamente el que en toda unión atornillada hay que buscar un compromiso entre las características del tornillo y las piezas a atornillar, de modo que sin sobrepasar el límite elástico del primero, la com-presión entre las segundas sean lo suficiente para no permitir ningún posible aflojamiento de sus elementos. Esta condición aparentemente evidente, es de gran importancia cuando puedan existir esfuerzos de cortadura, pues con-siguiendo un par de apriete correcto, esos esfuerzos pueden ser absorbidos por las fuerzas de rozamiento que se generan entre las piezas a unir y los elementos de sujeción.

Hemos partido de la base de no hacer trabajar al tornillo por encima de su límite elástico, pero hay un fenómeno muy importante a tener en cuenta, y es que también es posible inutilizar el tornillo sin necesidad de que las cargas aplicables a éste, en valor unitario superen a la carga en el límite elástico. Es el caso en que estas cargas actúan de forma oscilante con una frecuencia periódica determinada. Nos referimos al fenómeno conocido por rotura a la fatiga, cuyo origen está basado en la anisotropía de los materiales a escala cristalina. Experimentalmente se puede observar, al mismo tiempo que determinamos el valor de la resistencia a la fatiga mediante máquinas que someten al tornillo a esfuerzos oscilantes de magnitudes inferiores a las que pueden provocar la rotura de la pieza en con-diciones estáticas.

Una primera forma de experimentar consiste en hacer trabajar a la muestra de ensayo a una carga alternativa de mó-dulo constante con una frecuencia variable. Al llegar a un límite de frecuencia la muestra rompe. Es ese punto el que nos determina el valor de la fatiga.

De forma análoga, podríamos mantener constante el número de ciclos/segundo, e ir aumentando la carga en magni-tud hasta la rotura, comprobando de nuevo es inferior a la correspondiente fuerza estática en el límite elástico.

Para los objetivos que nos hemos propuesto con este informe, basta saber que la resistencia a la fatiga es proporcio-nal a la resistencia en el límite elástico para esfuerzos estáticos.

De todo lo expuesto, se deduce que en el ensamblaje por medio de tornillos hay que aplicar un momento de apriete Ma. determinado, función de una serie de variables intrínsecas para cada sistema, tales como la calidad del tornillo y tuerca; coeficientes de rozamiento entre las superficies de contacto; fuerzas de rozamiento generadas en estas superficies; fileteados del tornillo y tuerca, etc.

Nos vamos a permitir exponer la fórmula matemática resumida, que engloba todos estos conceptos, pensando que su deducción carece de interés para la aplicación inmediata que pretendemos, pero que siempre será ilustrativa al haber comprendido todos los conceptos que en ella intervienen.

Page 103: Esparragos y Tornillos Catalogo Tecnico

102DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PAR DE APRIETE EN LAS UNIONES ATORNILLADASIMPORTANCIA DE LA FUERZA DE PRETENSADO Y DEL

El par necesario a aplicar para alcanzar la fuerza de pretensado Pv será:

en la que:

df = diámetro de flancos. µ = coeficiente de rozamiento medio de: µa = coeficiente de rozamiento en las bases de asiento y µ + = coeficiente de rozamiento en las superficies de fileteado.

S = diámetro de la arandela de apoyo, aproximadamente la medida entre caras. dn = diámetro nominal del tornillo. p = paso de rosca.

El coeficiente de rozamiento adoptado es un valor deducido de experiencias llevadas a cabo con diversos tornillos y diferentes condiciones. El valor de las fuerzas de rozamiento como es lógico varia siempre que se modifiquen las condiciones superficiales, bien sea por recubrimientos galvánicos, lubricación o calidades de los materiales.

Ma = Pa [ µ( S + dn +0,58df) + 0,16p]4

Page 104: Esparragos y Tornillos Catalogo Tecnico

103DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

de los tornillos o cargas de roturaMÉTODOS PARA OBTENER EL DIÁMETRO

Al apretar los tornillos, debe hacerse como máximo hasta un 70 por 100 de su límite elástico, siendo éste el punto que llamamos apriete máximo.

Para obtener un apriete y su PAR de blocaje máximo para las diferentes dimensiones y en distintas clases de ros-cas. Las llaves dinamométricas garantizan una tensión constante en los tornillos, a fin de obtener su rendimiento máximo.

Para escoger el diámetro de un tornillo, el cual deba resistir una carga determinada (hasta el limite elástico) para un diámetro dado, se debe consultar el gráfico.

Las cargas citadas están calculadas al límite elástico SIN EL FACTOR DE SEGURIDAD. Si, por ejemplo, se desea te-ner un factor de seguridad, 3, el valor encontrado sobre el gráfico les mostrará también el tornillo en calidad 12.9 que puede reemplazar a uno de calidad 5.6.

EJEMPLOS

1.º El tornillo que debe escoger en calidad 12.9 (rosca Whitworth) deberá ser para una carga de 2.700 kilo-gramos, con un factor de seguridad 3. Tenemos que para S = 3, el tornillo que debe emplearse ha de ser calculado sobre la base 3 x 2.700 = 8.100 kilogramos.

Se traza una línea horizontal partiendo de la escala en kilogramos a la altura de 8.100 y en el punto en que la línea horizontal corta a la oblicua de 12.9, se halla la vertical y obtenemos un punto entre 7/16” y 1/2”, al que más se aproxima, por tanto, debe emplearse un tornillo de 1/2”.

2.º ¿Qué carga puede ejercerse sobre un tornillo calidad 12.9 UNC-3/4”, con factor de seguridad 2 (S = 2)?

Se traza una línea vertical hacia arriba, partiendo de la escala UNC sobre el punto 3/4” y en la intersec-ción de la línea vertical con la oblicua 12.9 se halla la horizontal hacia la escala en kilogramos, encon-trándose 21.200 kilogramos.

3.º ¿Qué tornillo en calidad 12.9 puede reemplazar a un tornillo 5.6 de 5/8”?

Partiendo de la escala Whitworth en la medida 5/8”, se halla la vertical hacia la línea oblicua 5.6 y en el punto en que se corta se lleva una horizontal hasta la escala 12.9. Desde esta última, se traza una vertical hacia abajo, la cual corta la base Whitworth entre 1/4” y 5/16”.

Page 105: Esparragos y Tornillos Catalogo Tecnico

104DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para el referido métodoREPRESENTACIÓN GRÁFICA

UNF.

UNC.

WHIT.

14

516

38

716

12

916

58

34

78

14

516

38

716

12

916

58

34

78

14

516

38

716

916

58

34

78

8 10 12 14 16 18 20 22 246M

1

1

1

23

45

67

89

1000

23

45

67

89 10

000

CAR

GA

DE

RO

TUR

A EN

KG

S.

23

45

67

8

1000

1000

0

3 2

CALIDAD 12.9 – RESISTENCIA A LA TRACCIÓN 1

20 Kgs./mm

2

CALIDAD 5.6 – RESISTENCIA A LA TRACCIÓN 6

0 Kgs./mm

2

CALIDAD 5.6 – RESISTENCIA A LA TRACCIÓN 3

7 Kgs./mm

2

1

12

Page 106: Esparragos y Tornillos Catalogo Tecnico

105DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

en las uniones atornilladasFUERZA DE PRETENSADO Y PAR DE APRIETE

Cargas en el límite elástico Po.2 fuerzas de pretensado Pv y pares de apriete Ma, para tornillos de rosca métrica más usuales según DIN 13, hoja 43 y dimensiones de apoyo de la cabeza conforme a DIN 912, 931, 933. Coeficiente medio de rozamiento µ = 0,14.

No insistiremos sobre la importancia de la utilización de llaves dinamométricas para garantizar que los valores de los pares de apriete aplicados coincidan con los que figuran en la tabla.

diá-metro nomi-

nal

Paso

Sec-ción

resis-tente núm.

Sec-ción del

núcleo núm.

Cargas en el Iímite clásico Po.2 (Kp) según sección resistente

Fuerzas de pretensado Pv (Kp) (70 a 75% de la carga límite elástico)

Par de apriete Ma (m. Kp)coeficiente de rozamiento= 0.14

5.6 8.8 10.9 12.9 5.6 8.8 10.9 12.9 5.6 8.8 10.9 12.9

M 4 0,7 8,78 7,75 260 560 790 950 195 390 545 655 0,15 0,29 0,41 0,49

M 5 0,8 14,2 12,7 420 910 1.280 1.530 320 635 895 1.070 0,3 0,6 0,85 1,0

M 6 1 20,1 17,9 600 1.290 1.810 2.170 450 900 1.260 1.510 0,5 0,5 1,4 1,7

M 8 1,25 36,6 32,8 1.090 2.340 .3290 3.950 820 1.650 2.320 2790 1,25 2,5 3,5 4,1

M 10 1,5 58 52,3 1.740 3.710 5.200 6.250 1 310 2.620 3.690 4.430 2,45 4,9 6,9 8,3

M 12 1,75 84,3 76,2 2.530 5.400 7.600 9.100 1.900 3.830 5.400 6.45 4,2 8,6 12 14,5

M 14 2 115 105 3.450 7.350 10.350 12.400 2.600 5.250 7.400 8.850 6,8 13,5 19 23,0

M 16 2 157 144 4.710 10.000 14.100 17.000 3.550 7.300 10.200 12.300 10,5 21 29,5 35,5

M 18 2.5 192 175 5.760 12.300 17.300 20.700 4.320 8.800 12.400 14.800 14,5 29 40,5 48,5

M 20 2,5 245 225 7.350 15.700 22.000 26.500 5.500 11.400 16.00 19.200 20 41 58 69

M 22 2,5 303 282 9.090 19.400 27.300 32.700 8.800 14.100 19.900 23.900 26,5 55 78 93

M 24 3 353 324 10.59 22.600 31.800 38.100 7.900 16.400 23.000 27.600 34,5 71 100 120

M 27 3 459 427 13.770 29.400 41.300 49.600 10.300 21.500 30.200 36.300 51 105 150 180

M 30 3,5 561 519 16.830 35.900 50.500 60.600 12.600 26.200 36.800 44.200 68 145 200 240

M 8 1 39,2 36 1.180 2.510 3.530 4.230 8.900 1.810 2.550 3.060 1,3 2,7 3,8 4,5

M 10 1,25 61,2 56,3 1.840 3.920 5.500 6.600 1.380 2830 3.980 4.770 2,6 5,2 7,3 8,8

M 12 1,25 92,1 86 2.760 5.900 8.300 9.950 2.070 4.330 6.100 7.300 4,6 9,5 13,5 16,0

M 12 1,5 88.1 81,1 2.640 5.650 7.950 9.500 1.980 4.070 5.700 6.850 4,4 9 12,5 15,0

M 14 1,5 125 116 3.750 8.000 11.250 13.500 2.800 5.850 8.250 9.900 7,3 15 21 25,0

M 16 1,5 167 157 5.010 10.700 15.000 18.000 3.75 7.900 11.100 13.300 10,5 22,5 31,5 38,0

M 18 1,5 216 205 6.480 13.800 19.400 23.300 4.850 10.300 14.500 17.400 15,5 32,5 46 55

M 20 1,5 272 259 8.160 17.400 24.500 29.400 6.100 13.000 18.300 22.000 21,5 46 64 77

M 22 1,5 333 319 9.990 21.300 30.000 36.000 7.500 16.100 22.600 27.100 28,5 61 86 105

M 24 2 384 365 11.520 24.600 34.600 41.500 8.600 18.300 25.700 30.900 36 78 110 130

M 27 2 496 473 14.880 31.700 44.600 53.600 11.200 23.800 33.500 40.200 54 115 160 195

M 30 2 621 596 18.630 39.700 55.900 67.100 14.300 30.000 42.200 50.600 76 160 225 270

Page 107: Esparragos y Tornillos Catalogo Tecnico

106DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

para la sustitución de tornillos 5.6, por las superiores calidades de 8.8 y 12.9EQUIVALENCIAS DE RESISTENCIAS Y UTILIZACIÓN

Carga máxima en el límite elástico

ROSCA MÉTRICA

CALIDAD 5.6 CALIDAD 8.8 CALIDAD 12.9

Calibre Kgs. Calibre Kgs. Calibre Kgs.

6 600 4 560

7 870 5 910

8 1.090 6 1.290 4 950

10 1.740 7 1.850 6 2.170

12 2.530 8 2.340 7 3.120

14 3.450 10 3.710 8 3.950

16 4.710 12 5.400 10 6.250

18 5.760 12 5.400 10 6.250

20 7.350 14 7.350 12 9.100

24 10.590 16 10.000 14 12.400

Page 108: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

107DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

Tablas útilesUseful charts

ANSI/DIN

Page 109: Esparragos y Tornillos Catalogo Tecnico

108DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

TABLA DE CONVERSIÓN / CONVERSION TABLE

TENSILE STRENGHT HARDNESS TENSILE STRENGHT HARDNESS

kp/mm2 N/mm2 HV HB HRB HRC kp/mm2 N/mm2 HV HB HRB HRC

20 200 63 60 54 530 165 157 83

21 210 65 62 55 540 168 160 84,5

22 220 69 66 545 170 162 85

23 225 70 67 56 550 172 163 85,5

230 72 68 57 560 175 166 86

24 240 75 71 58 570 178 169 86,5

25 250 79 75 575 180 171 87

26 255 80 76 59 580 181 172

260 82 78 60 590 184 175 88

27 270 85 81 41 595 185 176

28 280 88 84 45 61 600 187 178 89

29 285 90 86 48 62 610 190 181 89,5

290 91 87 49 63 620 193 184 90

30 300 94 89 51 625 195 185

305 95 90 52 64 630 197 187 91

31 310 97 92 54 65 640 200 190 91,5

32 320 100 95 56 66 650 203 193 92

33 330 103 98 58 67 660 205 195 92,5

335 105 100 59 68 670 208 198 93

34 340 107 102 60 675 210 199 93,5

35 350 110 105 62 69 680 212 201

36 360 113 107 63,5 70 690 215 204 94

37 370 115 109 64,5 71 700 219 208

38 380 119 113 66 705 220 209 95

385 120 114 67 72 710 222 211 95,5

39 390 122 116 67,5 73 720 225 214 96

40 400 125 119 69 74 730 228 216

41 410 128 122 70 75 740 230 219 96,5

415 130 124 71 76 750 233 221 97

42 420 132 125 72 755 235 223

43 430 135 128 73 77 760 237 225 97,5

44 440 138 131 74 78 770 240 228 98

45 450 140 133 75 79 780 243 231 21

46 460 143 136 76,5 785 245 233

47 465 145 138 77 80 790 247 235 99

48 470 147 140 77,5 81 800 250 238 99,5 22

49 480 150 143 78,5 82 810 253 240

490 153 145 79,5 83 820 255 242 23

50 495 155 147 80 84 830 258 245

51 500 157 149 81 835 260 247 24

52 510 160 152 81,5 85 840 262 249

53 520 163 155 82,5 86 850 265 252

Page 110: Esparragos y Tornillos Catalogo Tecnico

109DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

TENSILE STRENGHT HARDNESS TENSILE STRENGHT HARDNESS

kp/mm2 N/mm2 HV HB HRB HRC kp/mm2 N/mm2 HV HB HRB HRC

87 860 268 255 25 123 1210 376 357

865 270 257 124 1220 380 361

88 870 272 258 26 125 1230 382 363 39

89 880 275 261 126 1240 385 366

90 890 278 264 127 1250 388 369

91 900 280 266 27 1255 390 371

92 910 283 269 128 1260 392 372 40

915 285 271 129 1270 394 374

93 920 287 273 28 130 1280 397 377

94 930 290 276 131 1290 400 380

95 940 293 278 29 132 1300 403 383 41

96 950 295 280 133 1310 407 387

97 960 299 284 134 1320 410 390

965 300 285 135 1330 413 393 42

98 970 302 287 30 136 1340 417 396

99 980 305 290 137 1350 420 399

100 990 308 293 138 1360 423 402 43

101 995 310 295 31 139 1370 426 405

102 1000 311 296 140 1380 429 408

103 1010 314 299 1385 430 409

104 1020 317 301 32 141 1390 431 410

105 1030 320 304 142 1400 434 413 44

106 1040 323 307 143 1410 437 415

107 1050 327 311 33 144 1420 440 418

108 1060 330 314 145 1430 443 421

109 1070 333 316 146 1440 446 424 45

110 1080 336 319 34 147 1450 449 427

111 1090 339 322 1455 450 428

1095 340 323 148 1460 452 429

112 1100 342 325 149 1470 455 432

113 1110 345 328 35 150 1480 458 435 46

114 1120 349 332 151 1485 460 437

1125 350 333 152 1490 461 438

115 1130 352 334 153 1500 464 441

116 1140 355 337 36 154 1510 467 444

117 1150 358 340 155 1520 470 447

1155 360 342 156 1530 473 449 47

118 1160 361 343 157 1540 476 452

119 1170 364 346 37 158 1550 479 455

120 1180 367 349 1555 480 (456)

121 1190 370 352 159 1560 481 (457)

122 1200 373 354 38 160 1570 484 (460) 48

TABLA DE CONVERSIÓN / CONVERSION TABLE

Page 111: Esparragos y Tornillos Catalogo Tecnico

110DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

TENSILE STRENGHT HARDNESS TENSILE STRENGHT HARDNESS

kp/mm2 N/mm2 HV HB HRB HRC kp/mm2 N/mm2 HV HB HRB HRC

161 1580 486 (462) 199 1955 590 (561)

162 1590 489 (465) 1960 591 (562)

1595 490 (466) 200 1970 594 (564)

163 1600 491 (467) 201 1980 596 (567) 55

164 1610 494 (470) 202 1990 599 (569)

165 1620 497 (472) 49 203 1995 600 (570)

166 1630 500 (475) 204 2000 602 (572)

167 1640 503 (478) 205 2010 605 (575)

168 1650 506 (481) 206 2020 607 (577)

169 1660 509 (483) 207 2030 610 (580)

1665 510 (485) 208 2040 613 (582)

170 1670 511 (486) 209 2050 615 (584) 56

171 1680 514 (488) 50 210 2060 618 (587)

172 1690 517 (491) 211 2070 620 (589)

173 1700 520 (494) 212 2080 623 (592)

174 1710 522 (496) 213 2090 626 (595)

175 1720 525 (499) 214 2100 629 (598)

176 1730 527 (501) 51 2105 630 (599)

177 1740 530 (504) 215 2110 631 (600)

178 1750 533 (506) 216 2120 634 (602)

179 1760 536 (509) 217 2130 636 (604)

180 1770 539 (512) 218 2140 639 (607) 57

1775 540 (513) 2145 640 (608)

181 1780 541 (514) 219 2150 641 (609)

182 1790 544 (517) 52 220 2160 644 (612)

183 1800 547 (520) 221 2170 647 (615)

184 1810 550 (523) 222 2180 650 (618)

185 1820 553 (525) 223 2190 653 (620)

186 1830 556 (528) 224 2200 655 (622) 58

187 1840 559 (531) 675 59

188 1845 560 (582) 53 698 60

1850 561 (533) 720 61

189 1860 564 (536) 745 62

190 1870 567 (539) 773 63

191 1880 570 (542) 800 64

192 1890 572 (543) 829 65

193 1900 575 (546) 864 66

194 1910 578 (549) 54 900 67

195 1920 580 (551) 940 68

196 1930 583 (554)

197 1940 586 (557)

198 1950 589 (560)

TABLA DE CONVERSIÓN / CONVERSION TABLE

Page 112: Esparragos y Tornillos Catalogo Tecnico

111DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

THICKNESS

mm inches Kg./m. Kg./m. Kg./m.3 0,056 0,071 0,0613,175 0 1/8 0,062 0,079 0,0693,5 0,076 0,096 0,0833,968 7 5/32 0,097 0,124 0,1074 0,099 0,126 0,1094,5 0,125 0,159 0,1384,762 5 3/16 0,140 0,178 0,1545 0,154 0,196 0,1705,5 0,187 0,237 0,2065,556 2 7/32 0,190 0,242 0,2106 0,222 0,283 0,2456,350 0 1/4 0,247 0,317 0,2746,5 0,261 0,332 0,2877 0,302 0,385 0,3337,143 6 0/32 0,315 0,401 0,3477,5 0,347 0,442 0,3827,937 5 5/16 0,388 0,495 0,4288 0,395 0,502 0,4358,5 0,445 0,567 0,4918,7312 11/32 0,470 0,598 0,5189 0,499 0,636 0,5519,5 0,556 0,708 0,6149,525 0 3/8 0,559 0,712 0,61710 0,617 0,785 0,68010,378 7 13/32 0,657 0,836 0,72410,5 0,680 0,865 0,75011 0,746 0,950 0,82311,112 5 7/16 0,761 0,969 0,84011,5 0,815 1,038 0,89911,906 2 15/32 0,874 1,113 0,96412 0,888 1,130 0,97912,5 0,963 1,227 1,06212,699 8 1/2 0,994 1,266 1,09613 1,042 1,327 1,14913,493 7 17/32 1,123 1,429 1,23813,5 1,124 1,431 1,23914 1,208 1,539 1,33214,287 5 9/16 1,259 1,602 1,38814,5 1,296 1,650 1,42915 1,387 1,766 1,53015,081 2 19/32 1,402 1,785 1,54615,5 1,481 1,886 1,63315,875 0 5/8 1,554 1,978 1,71316 1,578 2,010 1,74016,5 1,678 2,137 1,85116,668 7 21/32 1,713 2,181 1,88917 1,782 2,269 1,96517,462 5 11/16 1,880 2,394 2,07317,5 1,888 2,404 2,08218 1,998 2,543 2,20318,256 2 23/32 2,055 2,617 2,26618,5 2,110 2,687 2,32719 2,226 2,834 2,45419,050 0 3/4 2,237 2,849 2,46719,5 2,344 2,985 2,58519,843 1 25/32 2,426 3,091 2,67720 2,466 3,140 2,71920,637 5 13/16 2,626 3,343 2,89521 2,719 3,462 2,998

THICKNESS

mm inches Kg./m. Kg./m. Kg./m.21,4312 27/32 2,832 3,605 3,12222 2,984 3,799 3,29022,225 0 7/8 3,045 3,875 3,35823 3,262 4,153 3,59623,018 7 29/32 3,267 4,159 3,60223,812 5 15/16 3,496 4,451 3,85524 3,551 4,522 3,91624,606 2 31/32 3,733 4,753 4,11625 3,853 4,906 4,24925,400 0 1 3,978 5,065 4,35226 4,168 5,307 4,59627 4,495 5,723 4,95628 4,824 6,154 5,33028,575 0 1 1/8 5,034 6,410 5,55129 5,185 6,602 5,71730 5,549 7,065 6,11831 5,925 7,544 6,53331,749 9 1 1/4 6,215 7,913 6,85332 6,313 8,038 6,96133 6,714 8,549 7,40334 7,127 9,075 7,85934,924 9 1 3/8 7,520 9,575 8,29235 7,553 9,616 822836 7,990 10,174 8,81137 8,440 10,747 9,30738 1 1/2 8,903 11,335 9,81738,099 9 8,950 11,395 9,86839 9,378 11,940 10,34040 9,865 12,560 10,87741 10,364 13,190 11,42841,274 9 1 5/8 10,504 13,373 11,58242 10,876 13,647 11,99243 11,400 14,515 12,57044 11,936 15,198 13,16244,449 9 1 3/4 12,181 15,510 13,43245 12,485 15,896 13,76746 13,046 16,611 14,38547 13,619 17,341 15,01747,624 9 1 7/8 13,984 17,805 15,41948 14,205 18,086 15,66349 14,803 18,848 16,32350 15,413 19,625 16,99650,799 9 2 15,911 20,258 17,54451 16,036 20,418 17,68252 16,671 21,226 18,38353 17,319 22,051 19,09653,974 9 2 1/8 17,962 22,869 19,80554 17,978 22,891 19,82455 18,650 23,746 20,56556 19,335 24,318 21,31957 20,031 25,505 22,08857,149 9 21/4 20,137 25,639 22,20458 20,740 26,407 22,86959 21,462 27,326 23,66560 22,195 28,260 24,47460,324 9 2 3/8 22,436 28,567 24,74061 22,941 29,210 25,29662 23,700 30,175 26,13363 24,470 31,157 26,982

TABLA DE PESOS DE PERFILESWEIGHT TABLE FOR ROUND, SCUARE AND HEXAGON BARS

Page 113: Esparragos y Tornillos Catalogo Tecnico

112DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

THICKNESS

mm inches Kg./m. Kg./m. Kg./m.63,499 9 2 1/2 24,861 31,653 27,41264 25,253 32,154 27,84665 26,049 33,166 28,72366 26,856 34,195 29,61366,674 9 2 5/8 27,408 34,898 30,22267 27,676 35,239 30,51868 28,509 36,298 31,43569 29,353 37,374 32,36769,849 9 2 3/4 30,081 38,300 33,16970 30,210 38,465 33,31272 31,961 40,694 35,24273,024 9 2 7/8 32,878 41,861 36,25374 33,762 42,987 37,22775 34,680 44,156 38,24076 35,611 45,342 39,26776,199 9 3 35,799 45,580 39,47478 37,510 47,759 41,36180 39,458 50,240 43,50982,549 9 3 1/4 42,013 53,494 45,20485 44,545 56,716 49,11888,899 8 3 1/2 48,726 62,040 53,72890 49,939 63,585 55,06695 55,642 70,846 61,35595,249 8 3 3/4 55,936 71,219 61,678100 61,654 78,500 67,983101,599 8 4 63,642 81,032 70,175105 67,973 86,546 74,951107,948 9 4 1/4 71,846 91,477 79,222110 74,601 94,985 82,259114,299 8 4 1/2 80,547 102,556 88,816115 81,537 103,816 89,907120 88,781 113,040 97,895120,649 8 4 3/4 89,745 114,268 98,958125 96,337 122,656 106,223126,999 8 5 99,441 126,612 108,649130 104,195 132,665 114,891133,349 8 5 1/4 109,634 139,590 120,888135 112,364 143,066 123,899139,699 8 5 1/2 120,323 153,201 132,676140 120,841 153,860 133,247145 129,627 165,046 142,934146,049 7 5 3/4 131,511 167,445 145,011150 138,721 176-625 152,962152,299 7 6 143,195 182,321 157,895155 148,123 188,596 163,329158,749 7 6 1/4 155,376 197,809 171,327160 157,833 200,960 174,036165 167,852 213,716 185,084165,099 7 6 1/2 168,055 213,975 185,307170 178,179 226,865 196,471171,44 7 6 3/4 181,231 230,751 199,836175 188,814 240,406 206,198177,799 7 7 194,904 248,160 214,913180 199,757 254,340 220,265184,149 7 7 1/4 209,075 266,202 230,538185 211,010 268,666 232,672

THICKNESS

mm inches Kg./m. Kg./m. Kg./m.190 222,570 283,385 245,418190,499 7 7 1/2 223,742 284,799 246,711195 234,438 298,496 258,505196,849 7 7 3/4 238,907 304,186 263,433200 246,614 314,000 271,932203,199 6 8 254,509 324,127 280,702205 259,100 329,896 285,698210 271,893 346,185 299,805215 284,994 362,866 314,251215,899 6 8 1/2 287,384 365,909 316,886220 298,403 379,940 329,038225 312,122 397,406 344,164228,599 6 9 322,189 410,224 355,264230 326,148 415,265 359,630235 340,483 433,516 375,436240 355,125 452,160 391,582241,299 6 9 1/2 358,981 457,070 395,834245 370,076 471,196 408,068250 385,336 490,625 424,894253,999 6 10 397,768 506,433 438,583255 400,903 510,446 442,059260 416,779 530,660 459,565265 432,963 551,266 477,410266,699 5 10 1/2 438,534 558,360 483,553270 449,455 572,265 495,596275 466,256 593,656 514,121279,399 5 11 481,294 612,803 530,702280 483,365 615,440 532,986285 500,782 637,616 552,192290 518,508 660,185 571,737292,099 5 11 1 /2 526,042 669,779 580,045295 536,541 683,146 591,622300 554,883 706,500 611,847304,799 5 12 572,780 729,286 631,580305 573,534 730,246 632,411310 592,492 754,385 653,316315 611,759 778,916 674,561317,499 5 12 1/2 621,506 791,327 685,301320 631,334 803,840 696,146325 651,217 829,156 718,070330 671,409 854,865 740,334330,199 4 13 672,220 855,898 741,229335 691,909 880,966 762,933340 712,717 907,460 786,883342,899 4 724,924 923,003 799,343345 13 1/2 733,833 934,346 809,167350 755,258 961,625 832,791355 776,991 989,296 856,775355,599 4 14 779,617 992,640 859,650360 799,032 1 017,360 881,059365 821,381 1 045,816 905,703368,299 4 14 1/2 836,298 1 964,809 922,150370 844,039 1 074,665 930,687375 867,005 1 103,906 956,010380 890,279 1 133,540 981,674380,999 3 15 894,968 1 139,510 986,843

TABLA DE PESOS DE PERFILESWEIGHT TABLE FOR ROUND, SCUARE AND HEXAGON BARS

Page 114: Esparragos y Tornillos Catalogo Tecnico

113DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

THICKNESS

mm inches Kg./m. Kg./m. Kg./m.385 913,862 1 163,566 1 007,677390 937,753 1 193,985 1 034,021393,699 3 15 1/2 955,627 1 216,743 1 053,729395 961,952 1 224,796 1 060,704400 986,459 1 256,000 1 087,727405 1 011,275 1 287,596 1 115,091406,399 3 16 1 018,275 1 296,509 1 122,808410 1 036,399 1 319,585 1 142,794415 1 081,831 1 351,966 1 170,837419,099 3 16 1/2 1 082,911 1 378,807 1 194,080420 1 087,571 1 384,740 1 199,219425 1 113,620 1 417,906 1 227,942430 1 139,977 1 451,465 1 257,005431,799 3 17 1 149,537 1 463,637 1 267,545435 1 166,642 1 485,416 1 286,408440 1 193,616 1 519,760 1 316,150444,499 2 17 1/2 1 220,855 1 550,999 1 343,203445 1 222,285 1 554,496 1 346,233450 1 248,487 1 589,625 1 376,655455 1 276,386 1 625,146 1 407,417457,199 2 18 1 288,754 1 640,894 1 421,054460 1 304,592 1 661,060 1 438,519465 1 333,107 1 697,366 1 469,962469,8992 18 1/2 1 361,346 1 733,313 1 501,098470 1 361,930 1 734,056 1 501,744475 1 391,062 1 771,156 1 533,866480 1 420,501 1 808,640 1 566,327482,599 2 19 1 435,927 1 828,281 1 583,335485 1 450,249 1 846,516 1 599,129490 1 480,305 1 884,785 1 632,271495 1 510,670 1 923,446 1 665,756495,299 1 19 1/2 1 512,496 1 925,771 1 667,764500 1 541,343 1 962,500 1 699,574505 1 572,323 2 001,946 1 733,734507,999 1 20 1 591,055 2 025,795 1 754,388510 1 603,613 2 041,785 1 768,235515 1 635,210 2 082,016 1 803,076520 1 667,116 2 122,640 1 838,258520,699 1 20 1/2 1 671,602 2 128,351 1 843,204525 1 699,330 2 163,656 1 873,779530 1 731,852 2 205,055 1 909,640533,399 1 21 1 754,138 2 233,440 1 934,213535 1 764,683 2 246,866 1 945,841540 1 797,822 2 289,060 1 982,281545 1 831,269 2 331,646 2 019,262546,099 1 21 1/2 1 838,662 2 341,060 2 027,415550 1 865,024 2 374,625 2 056,483555 1 899,088 2 417,996 2 094,043558,799 0 22 1 925,176 2 451,212 2 122,809560 1 933,460 2 461,760 2 131,944565 1 968,140 2 505,916 2 170,184570 2 003,129 2 550,465 2 208,764571,499 0 22 1/2 2 013,678 2 563,897 2 220,397575 2 038,425 2 595,406 2 247,685580 2 074,030 2 640,740 2 286,945584,199 0 23 2 104,170 2 679,115 2 320,178585 2 109,944 2 686,466 2 326,545590 2 146,165 2 732,585 2 366,485595 2 182,695 2 779-096 2 406,765596,899 0 23 1/2 2 196,650 2 796,864 2 483,337600 2 219,533 2 826,000 2 447,384

FORMULAS FOR THE CALCULATION OF WEIGHTSFOR DIFFERENT PROFILES AND MEASUREMENTS

ROUND: 1 m. weights d x d x 0,62 / 100 Kg.

SCUARE: 1 m. weights a x a x 0,79 / 100 Kg.

PLANE: 1 m. weights a x b x 0,79 / 100 Kg.

HEXAGONAL: 1 m. weights s x s x 0,68 / 100 Kg.

OCTAGONAL: 1 m. weights s x s x 0,65 / 100 Kg.

TRIANGULAR: 1 m. weights a x a x 0,34 / 100 Kg.

TABLA DE PESOS DE PERFILESWEIGHT TABLE FOR ROUND, SCUARE AND HEXAGON BARS

Page 115: Esparragos y Tornillos Catalogo Tecnico

114DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

CONVERSIÓN DE PULGADAS EN MILÍMETROSCONVERSION OF INCHES TO MILLIMETRES(1 inche = 25,399772 mm)

Inches 0 1/16 1/8 3/16 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16

mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm.

0 0,000 1,587 3,175 4,762 6,350 7,937 9,525 11,112 12,700 14,287 15,875 17,462 19,050 20,637 22,225 23,812

1 25,400 28,987 28,575 30,162 31,750 33,337 34,925 36,512 38,100 39,687 41,275 42,862 44,450 46,037 47,625 49,212

2 50,800 52,387 53,975 55,562 57,149 58,737 60,324 61,912 63,499 65,087 66,674 68,262 69,849 71,437 73,024 74,612

3 76,199 77,787 79,374 80,962 82,549 84,137 85,724 87,312 88,899 90,487 92,074 93,662 95,249 96,837 98,424 100,012

4 101,599 103,187 104,774 106,362 107,949 109,537 111,124 112,711 114,299 115,886 117,474 119,061 120,649 122,236 123,824 125,411

5 126,999 128,586 130,174 131,761 133,349 134,936 136,524 138,111 139,699 141,286 142,874 144,461 146,049 147,638 149,224 150,811

6 152,399 153,986 155,574 157,161 158,749 160,336 161,924 163,511 165,099 166,686 168,273 169,861 171,448 173,036 174,623 176,211

7 177,798 179,386 180,973 182,561 184,148 185,736 187,323 188,911 190,498 192,086 193,673 195,261 196,848 198,438 200,023 201,611

8 203,198 204,786 206,373 297,961 209,548 211,136 212,723 214,311 215,898 217,486 219,073 220,661 222,248 223,835 225,423 227,010

9 228,598 230,185 231,773 233,360 234,948 236,535 238,123 239,710 241,298 242,885 244,473 246,060 247,648 249,235 250,823 252,410

10 253,998 255,585 257,173 258,760 260,348 261,935 263,523 265,110 266,698 268,285 269,873 271,460 273,048 274,635 276,223 277,810

11 279,397 280,985 282,572 284,160 285,747 287,335 288,922 290,510 292,097 293,685 295,272 296,860 298,447 300,035 301,622 303,210

12 304,797 306,385 307,972 309,560 311,147 312,735 314,322 315,910 317,497 319,085 320,672 322,260 323,847 325,435 327,022 328,610

13 330,197 331,785 333,372 334,959 336,547 338,134 339,722 341,309 342,897 344,484 346,072 347,659 349,247 350,834 352,422 354,009

14 355,597 357,184 358,772 360,359 361,947 363,534 365,122 366,709 368,297 369,884 371,472 373,059 374,647 376,234 377,822 379,409

15 380,997 382,534 394,172 385,759 387,347 388,934 390,521 392,109 393,696 395,284 396,871 398,459 400,046 401,634 403,22I 404,809

16 406,396 407,984 409,571 411,159 412,746 414,334 415,921 417,509 419,096 420,684 422,271 423,859 425,446 427,034 428,621 430,209

17 431,796 433,384 434,971 436,559 438,146 439,734 441,321 442,909 444,496 446,083 447,671 449,258 450,846 452,433 454,021 455,608

18 457,196 458,783 460,371 461,958 463,546 465,133 466,721 468,308 469,896 471,483 473,071 474,658 476,246 477,833 479,421 481,008

19 482,596 484,183 485,771 487,358 488,946 490,533 492,121 493,708 495,296 496,883 498,471 500,058 501,645 503,233 504,820 506,408

20 507,995 509,583 511,170 512,758 514,345 515,933 517,520 519,108 520,695 522,283 523,870 525,458 527,045 528,633 530,223 531,808

21 533,395 534,983 536,570 538,158 539,745 541,333 542,920 544,508 546,095 547,683 549,270 550,858 552,445 554,033 555,620 557,207

22 558,795 560,382 561,970 563,557 565,145 566,732 568,320 569,907 571,495 573,082 574,670 576,257 577,845 579,432 581,020 582,607

23 584,195 585,782 587,370 588,957 590,545 592,132 593,720 595,307 596,895 598,482 600,070 601,657 603,245 604,832 606,420 608,007

24 609,595 611,182 612,769 614,357 615,944 617,532 619,119 620,707 622,294 623,882 625,469 627,057 628,644 630,232 631,819 633,407

25 634,994 636,582 638,169 639,757 641,344 642,932 644,519 646,107 647,694 649,282 650,869 652,457 654,044 655,632 657,219 658,807

26 660,394 661,992 663,569 665,157 666,744 668,332 669,919 671,506 673,091 674,681 676,269 677,856 679,444 681,031 682,619 684,206

27 685,794 687,381 688,969 690,556 692,144 693,731 695,319 696,906 698,494 700,081 701,669 703,256 704,844 706,431 708,019 709,606

28 711,194 712,781 714,369 715,956 717,544 719,131 720,719 722,306 723,894 725,481 727,068 728,656 730,243 731,831 733,418 735,006

29 736,593 738,181 739,768 741,356 742,943 744,531 746,118 747,706 749,293 750,881 752,468 754,056 755,643 757,231 758,818 760,406

30 761,993 763,581 765,168 766,756 768,343 769,931 771,518 773,106 774,693 776,281 777,868 779,456 781,043 782,630 784,218 785,805

31 787,393 788,980 790,568 792,155 793,743 795,330 796,918 798,505 800,093 801,880 803,268 804,855 806,443 803,030 809,618 811,205

32 812,793 814,380 815,968 817,555 819,143 820,730 822,318 823,905 825,493 827,080 828,668 830,255 831,843 833,430 835,018 836,605

33 838,192 839,780 841,367 842,955 844,542 816,130 847,717 849,305 850,892 852,480 854,067 855,655 857,242 858,830 860,417 862,005

34 863,592 865,180 866,767 868,355 869,942 871,530 873,117 874,705 876,292 877,880 879,467 881,055 882,642 884,230 885,817 887,405

35 888,992 890,580 892,167 893,754 895,342 896,929 898,517 900,104 901,692 903,279 904,867 906,454 908,042 909,629 911,217 912,804

36 914,392 915,979 917,567 919,154 920,742 922,329 923,917 925,504 927,092 928,679 930,267 931,854 033,442 935,029 936,617 938,204

37 939,792 941,379 942,967 944,554 946,142 947,729 949,316 950,904 952,491 954,079 955,666 957,254 958,841 960,429 962,016 963,604

38 965,191 966,779 968,369 969,954 971,541 973,129 974,716 976,304 977,891 979,479 981,066 982,654 984,241 985,829 987,416 989,004

39 990,594 992,179 993,766 995,354 996,941 998,529 1000,12 1001,70 1003,29 1004,88 1006,47 1008,05 1009,64 1011,23 1012,82 1014,40

40 1015,99 1017,58 1019,17 1020,75 1022,34 1023,93 1025,52 1027,10 1028,69 1030,28 1031,87 1033,45 1015,04 1036,63 1038,22 1039,80

41 1041,39 1042,98 4044,57 1046,45 1047,74 1049,33 1050,92 1052,50 1054,09 1055,68 1057,27 1058,85 1060,44 1062,03 1063,62 1065,20

42 1066,79 1068,38 1069,97 1074,55 1073,14 1074,73 1076,32 1077,90 1079,49 1081,08 1082,67 1084,25 1085,84 1087,43 1089,02 1090,60

43 1092,19 1093,78 1095,37 1096,95 1098,54 1100,13 1101,72 1103,30 1104,89 1106,48 1108,07 1109,65 1111,24 11/2,83 1114,41 1116,00

44 1117,59 1119,10 1120,76 1122,35 1123,94 1125,53 1127,11 1128,70 1130,29 1131,88 1133,46 113,05 1136,64 1138,23 1439,81 1141,40

45 1142,99 1144,58 1146,16 1147,75 1149,34 1150,93 1152,51 1154,10 1155,69 1157,28 1158,86 1160,45 1162,04 1163,63 1165,21 1166,80

46 1168,39 1169,98 1171,56 1173,15 1174,74 1176,33 1177,91 1179,50 1181,09 1182,68 1184,26 1185,85 1187,44 1189,03 1490,61 1192,20

47 1193,79 1195,38 1196,96 1198,55 1200,14 1201,73 1203,31 1204,90 1206,49 1208,98 1209,66 1211,25 1212,84 1214,43 1216,01 1217,60

48 1219,19 1220,78 1222,36 1223,95 1225,54 1227,13 1228,71 1230,30 1231,89 1233,48 1235,06 1236,65 1238,24 1239,83 1241,41 1243,00

49 1244,59 1246,18 1247,76 1249,35 1250,94 1252,53 1254,11 1255,70 1257,29 1258,88 1260,46 1262,05 1263,61 1265,23 1266,81 1268,40

Page 116: Esparragos y Tornillos Catalogo Tecnico

115DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

Inches 0 1/16 1/8 3/16 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 13/16 7/8 15/16

mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm. mm.

50 1269,99 1271,56 1273,16 1274,75 1276,34 1277,93 1279,51 1281,10 1282,69 1284,28 1285,86 1287,45 1289,04 1290,63 1292,21 1293,80

51 1295,39 1296,98 1298,56 1300,15 1301,74 1303,33 1304,91 1306,50 1308,09 1309,68 1311,26 1312,85 1314,44 1316,03 1317,81 1319,20

52 1320,79 1322,38 1323,96 1325,55 1327,14 1328,73 1330,31 1331,90 1333,49 1335,08 1336,66 1338,25 1339,84 1341,43 1343,01 1344,60

53 1346,19 1347,78 1349,30 1350,95 1352,54 1354,13 1355,71 1357,30 1358,89 1360,48 1362,06 1363,65 1365,24 1366,83 1368,41 1370,00

54 1371,59 1373,18 1374,76 1376,35 1377,94 1379,53 1381,11 1382,70 1384,29 1385,88 1387,46 1389,05 1390,64 1392,23 1393,81 1395,40

55 1396,99 1398,57 1400,16 1401,75 1403,34 1404,92 1406,51 1408,10 1409,69 1411,27 1412,86 1414,45 1416,04 1417,62 1419,21 1420,80

58 1422,39 1423,97 1425,56 1427,15 1428,74 1430,32 1431,91 1433,50 1435,09 1436,67 1438,26 1439,85 1414,44 1443,02 1444,61 1446,20

57 1447,79 1449,37 1450,96 1452,55 1454,14 1455,72 1457,31 1458,90 1460,49 1462,07 1463,66 1465,25 1466,84 1468,42 1470,01 1471,60

58 1473,19 1474,77 1476,38 1477,95 1479,54 1481,12 1482,71 1484,30 1485,89 1487,47 1489,06 1490,65 1492,24 1493,82 1495,41 1497,00

59 1496,59 1500,17 1501,78 1503,35 1504,94 1506,52 1506,11 1509,70 1511,29 1512,87 1514,46 1516,05 1517,64 1519,22 1520,81 1522,40

60 1523,99 1525,57 1527,16 1528,75 1530,34 1531,92 1533,51 1535,10 1536,69 1538,27 1539,86 1541,45 1543,04 1544,62 1546,21 1547,80

61 1549,39 1550,97 1552,56 1554,15 1555,74 1557,32 1558,91 1560,50 1562,09 1563,67 1565,26 1566,85 1568,44 1570,02 1571,61 1573,20

62 1574,79 1576,37 1577,98 1579,55 1581,14 1582,72 1584,31 1585,90 1587,49 1589,07 1590,66 1592,25 1593,84 1595,42 1597,01 1598,60

63 1600,19 1601,77 1603,36 1604,95 1606,54 1608,12 1609,71 1611,30 1612,89 1614,47 1616,06 1617,65 1619,24 1620,82 1622,41 1624,00

64 1625,59 1627,17 1628,78 1630,35 1631,94 1633,52 1635,11 1636,70 1638,29 1639,87 1641,46 1643,05 1644,64 1646,22 1647,81 1649,40

65 1650,99 1652,57 1654,16 1655,75 1657,34 1658,92 1660,51 1662,10 1663,69 1665,27 1666,86 1668,45 1670,04 1671,62 1673,21 1674,80

66 1676,38 1677,97 1679,56 1681,15 1682,73 1684,32 1685,91 1687,50 1689,08 1690,67 1692,26 1693,85 1695,43 1697,02 1698,61 1700,20

67 1701,78 1703,37 1704,96 1706,55 1708,13 1709,72 1711,31 1712,90 1714,48 1716,57 1717,66 1719,25 1720,83 1722,42 1724,01 1725,60

68 1727,18 1728,77 1730,36 1731,95 1733,53 1735,12 1736,71 1738,30 1739,88 1741,47 1743,06 1744,65 1746,23 1747,82 1749,41 1751,00

69 1752,58 1754,17 1755,76 1757,35 1759,93 1760,52 1762,11 1763,70 1765,28 1766,87 1768,46 1770,05 1771,63 1773,22 1774,81 1776,40

70 1777,98 1779,57 1781,16 1782,75 1784,33 1785,92 1787,51 1789,10 1790,68 1792,27 1793,86 1795,45 1797,03 1798,62 1800,21 1801,80

71 1803,38 1804,97 1806,56 1808,15 1809,73 1811,32 1812,91 1814,50 1816,08 1817,67 1819,26 1820,85 1822,43 1824,02 1825,61 1827,20

72 1828,78 1830,37 1831,96 1833,55 1835,13 1836,72 1838,31 1839,90 1841,48 1843,07 1844,66 1846,25 1847,83 1849,42 1851,01 1852,60

73 1854,18 1855,77 1857,36 1858,95 1860,53 1862,12 1863,71 1865,30 1866,88 1868,47 1870,06 1871,65 1873,23 1874,82 1876,41 1878,00

74 1879,58 1881,17 1882,76 1854,35 1885,92 1887,52 1889,11 1890,70 1892,28 1893,87 1895,46 1897,05 1898,63 1900,22 1901,81 1903,40

75 1904,98 1906,57 1908,16 1909,75 1911,33 1912,92 1914,51 1916,10 1917,68 1919,27 1920,86 1922,45 1924,03 1925,62 1927,21 1928,80

76 1930,38 1931,97 1933,56 1935,15 1936,72 1938,32 1939,91 1941,50 1943,08 1944,67 1946,26 1947,85 1949,43 1951,02 1952,61 1954,19

77 1955,78 1957,37 1958,96 1960,54 1962,13 1963,72 1965,31 1966,89 1968,48 1970,07 1971,66 1973,24 1974,83 1976,42 1978,01 1979,59

78 1981,18 1982,77 1984,36 1985,94 1987,53 1989,12 1990,71 1992,29 1993,88 1995,47 1997,06 1998,64 2060,23 2001,82 2003,41 2004,99

79 2006,58 2008,17 2009,76 2011,34 2012,93 2014,52 2016,11 2017,69 2019,28 2020,87 2022,46 2024,04 2025,63 2027,22 2028,81 2030,39

80 2031,98 2033,57 2035,16 2036,74 2038,32 2039,92 2041,51 2043,09 2044,69 2046,27 2047,86 2049,44 2051,03 2052,62 2054,21 2055,79

81 2057,38 2058,97 2060,56 2062,14 2063,73 2065,32 2066,91 2068,49 2070,08 2071,67 2073,26 2074,84 2076,43 2078,02 2079,61 2081,19

82 2082,78 2084,37 2085,96 2087,54 2089,13 2090,72 2092,31 2093,89 2095,48 2097,07 2098,66 2100,24 2101,83 2103,42 2105,01 2106,59

83 2108,18 2109,77 2111,36 2112,94 2114,53 2116,12 2117,71 2119,29 2120,88 2122,47 2124,06 2125,64 2127,23 2128,82 2130,41 2131,99

84 2133,56 2135,17 2136,76 2138,34 2139,93 2141,52 2143,11 2144,69 2146,28 2147,87 2149,46 2151,04 2152,63 2154,22 2155,81 2157,39

85 2158,98 2160,57 2162,16 2163,74 2165,33 2166,82 2168,51 2170,09 2171,68 2173,27 2174,86 2176,44 2178,03 2179,62 2181,21 2182,79

86 2184,38 2185,97 2187,56 2189,14 2190,73 2192,32 2193,91 2195,49 2197,08 2198,67 2200,26 2201,84 2203,43 2205,02 2206,61 2208,19

87 2209,78 2211,37 2212,96 2214,54 2216,13 2217,72 2219,31 2220,89 2222,48 2224,07 2225,66 2227,24 2228,83 2230,42 2232,00 2233,59

88 2235,18 2236,77 2238,35 2239,94 2241,53 2243,12 2244,70 2246,29 2247,88 2249 47 2251,05 2252,64 2254,23 2755,82 2257,40 2258,99

89 2260,58 2262,17 2263,75 2265,34 2266,93 2268,52 2270,10 2271,69 2273,28 2274,87 2276,45 2278,04 2279,63 2281,22 2282,80 2284,39

90 2285,98 2287,57 2289,15 2290,74 2292,32 2293,92 2295,50 2297,09 2298,68 2300,27 2301,85 2334,00 2305,03 2306,62 2308,20 2309,79

91 2311,38 2312,97 2314,55 2316,14 2317,73 2319,32 2320,90 2322,49 2324,08 2325,67 2327,25 2328,84 2330,43 2332,02 2333,60 2335,19

92 2336,78 2338,37 2339,95 2341,54 2343,13 2344,72 2346,30 2347,89 2349,48 2351,07 2352,65 2354,24 2355,83 2357,42 2359,00 2360,59

93 2362,18 2363,77 2365,35 2366,94 2368,53 2370,12 2371,70 2373,29 2374,88 2376,47 2378,05 2379,64 2381,23 2382,82 2384,40 2385,99

94 2387,58 2389,17 2390,75 2392,34 2393,93 2395,52 2397,10 2398,69 2400,28 2401,87 2403,45 2405,04 2406,63 2408,22 2409,80 2411,39

95 2412,98 2414,57 2416,15 2417,74 2419,33 2420,92 2422,50 2424,09 2425,68 2427,27 2428,85 2430,44 2432,03 2433,62 2435,20 2436,79

96 2438,38 2439,97 2441,55 2443,14 2444,73 2446,32 2447,90 2449,49 2451,08 2452,67 2454,25 2455,84 2457,43 2459,02 2460,60 2462,19

97 2463,78 2465,37 2466,95 2468,54 2470,13 2471,72 2473,30 2474,89 2476,48 2478,07 2479,65 2481,24 2482,83 2484,42 2486,00 2487,59

98 2489,18 2490,77 2492,35 2493,94 2495,53 2497,12 2496,70 2500,29 2501,88 2503,47 2505,05 2506,64 2508,23 2509,81 2511,40 2512,99

99 2514,58 2516,16 2517,75 2519,34 2520,93 2522,51 2524,10 2525,69 2527,28 2528,86 2530,45 2532,04 2533,63 2535,2I 2536,80 2530,29

CONVERSIÓN DE PULGADAS EN MILÍMETROSCONVERSION OF INCHES TO MILLIMETRES(1 inche = 25,399772 mm)

Page 117: Esparragos y Tornillos Catalogo Tecnico

116DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

CONVERSIÓN DE MILÍMETROS A PULGADASCONVERSION OF MILLIMETRES TO INCHES

mm 0 1 2 3 4 5 6 7 8 9

inches inches inches inches inches inches inches inches inches inches

0 — 0,039370 0,073741 0,118111 0,157482 0,196852 0,235223 0,275593 0,314963 0,354334

10 0,393704 0,433075 0,472445 0,511816 0,551186 0,590556 0,629927 0,669297 0,708668 0,748038

20 0,787409 0,826779 0,866149 0,905520 0,944890 0,984261 1,023631 1,063002 1,102372 1,141742

30 1,181113 1,220483 1,259854 1,299224 1 338595 1,377965 1,417335 1,456706 1,496076 1,535447

40 1,574817 1,614188 1,653558 1,692929 1,732299 1,771669 1,811040 1,850410 1,889781 1,929151

50 1,968522 2,007892 2,047262 2,086633 2,126003 2,165374 2,204744 2,244115 2,283485 2,322855

60 2,362226 2,401596 2,440967 2,480337 2,519708 2,559078 2,598448 2,637819 2,677189 2,716560

70 2,755930 2,795301 2,834671 2,874041 2,913412 2,952782 2,992153 3,031523 3,070894 3,110264

80 3,149635 3,189005 3,228375 3,267746 3,307116 3,346487 3,385857 3,425228 3,464598 3,503968

90 3,543339 3,582709 3,622083 3,661450 3,700821 3,740191 3,779561 3,818932 3,858302 3,897673

100 3,937043 3,976414 4,015784 4,055155 4,094525 4,133895 4,173266 4,212636 4,252007 4,291377

110 4,330748 4,370118 4,409488 4,448859 4,488229 4,527600 4,566970 4,606341 4,645711 4,685081

120 4,724452 4,763822 4,803193 4,842563 4,881934 4,921304 4,960674 5,000045 5,039415 5,078786

130 5,118156 5,157527 5,196897 5,236267 5,275638 5,315008 5,354379 5,393749 5,433120 5,472400

140 5,511861 5,551231 5,590601 5,629972 5,669342 5,708713 5,748083 5,787454 5,826824 5,866194

150 5,905565 5,944935 5,534306 6,023676 6,063047 6,102417 6,141787 6,181158 6,220528 6,259899

160 6,299269 6,338640 6,378010 6,417380 6,456751 6,496121 6,535492 6,574862 6,614233 6,653603

170 6,692973 6,732344 6,771714 6,811085 6,850455 6,889826 6,929196 5,968567 7,007931 7,047307

180 7,086678 7,126048 7,165419 7,204789 7,244160 7,283530 7,322900 7,362271 7,401641 7,441012

190 7,480382 7,519753 7,559123 7,598493 7,637864 7,677234 7,716605 7,755975 7,795346 7,834716

200 7,874086 7,913457 7,952827 7,992198 8,031568 8,070939 8,110309 8,149679 8,189050 8,228420

210 8,267791 8,307161 8,346532 8,385902 8,425272 8,464643 8,504013 8,543384 8,582754 8,622125

220 8,661495 8,700866 8,740236 8,779606 8,818977 8,858347 8,897718 8,937088 8,976459 9,015829

230 9,055199 9,094570 9,133940 9,173311 9,212681 9,252052 9,291422 9,330792 9,370163 9,409533

240 9,448904 9,488274 9,527645 9,567015 9,606385 9,645756 9,685126 9,724497 9,763867 9,803238

250 9,842608 9,881978 9,921349 9,960719 10,000090 10,039460 10,078831 10,118201 10,157571 10,196942

260 10,236312 10,275683 10,315053 10,354424 10,393794 10,433165 10,472535 10,511905 10,551276 10,590646

270 10,630017 10,669387 10,708758 10,748128 10,787498 10,826869 10,866239 10,905610 10,944980 10,984351

280 11,023721 11,063091 11,102462 11,141832 11,181203 11,220573 11,259944 11,299314 11,338684 11,378055

290 11,417425 11,456796 11,496166 11,535537 11,574907 11,614277 11,653648 11,693018 11,732389 11,771759

300 11,811130 11,850500 11,889871 11,929241 11,968611 12,007982 12,047352 12,086723 12,126093 12,165464

310 12,204834 12,244204 12,283575 12,322945 12,362316 12,401686 12,441057 12,480427 12,519797 12,559168

320 12,598538 12,637909 12,677279 12,716650 12,756200 12,795390 12,834761 12,874131 12,913502 12,952872

330 12,992243 13,031613 13,070983 13,110354 13,149724 13,189095 13,228465 13,267836 13,307206 13,346576

340 13,385947 13,425317 13,464688 13,504058 13,543429 13,582799 13,622170 13,661540 13,700910 13,740281

350 13,779651 13,819022 13,858392 13,897763 13,937133 13,976503 14,015874 14,055244 14,094615 14,133985

360 14,173356 14,212726 14,252096 14,291467 14,330837 14,370208 14,409578 14,448949 14,488319 14,527689

370 14,567060 14,606430 14,645801 14,685171 14,724542 14,763912 14,803282 14,842653 14,882023 14,921394

380 14,960764 15,000135 15,039505 15,078875 15,118246 15,157616 15,196997 15,236357 15,275728 15,315098

390 15,354469 15,393839 15,433209 15,472580 15,511950 15,551321 15,590691 15,630062 15,669432 15,708802

400 15,748173 15,787543 15,826914 15,866284 15,905655 15,945025 15,984395 16,023766 16,063136 16,102507

410 16,141877 16,181248 16,220618 16,259988 16,299359 16,338729 16,378100 16,417470 16,456841 16,496211

420 16,535581 16,574952 16,614322 16,653693 16,693063 16,732444 16,771804 16,811175 16,850545 16,889915

430 16,929286 16,968656 17,008027 17,047397 17,086768 17,126138 17,165508 17,204879 17,244249 17,283620

440 17,322990 17,362361 17,401731 17,441101 17,480472 17,519842 17,559213 17,598583 17,637954 17,677324

450 17,716694 17,756065 17,795435 17,834806 17,874176 17,913547 17,952917 17,992287 18,031658 18,071028

460 18,110399 18,149769 18,189140 18,228510 18,267880 18,307251 18,346621 16,385992 18,425362 18,464733

470 18,504103 18,543474 18,582844 18,622214 18,661585 18,700955 18,740326 18,779696 18,819067 18,858437

480 18,897807 18,937178 18,976548 19,015919 19,055289 19,094660 19,134030 19,173400 19,212771 19,252141

490 19,291512 19,330862 19,370253 19,409623 19,448993 19,488364 19,527734 19,567095 19,606465 19,645836

Page 118: Esparragos y Tornillos Catalogo Tecnico

117DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

CONVERSIÓN DE MILÍMETROS A PULGADASCONVERSION OF MILLIMETRES TO INCHES

mm 0 1 2 3 4 5 6 7 8 9

inches inches inches inches inches inches inches inches inches inches

500 19,685216 19,724586 19,763957 19,803327 19,842698 19,882068 19,921439 19,960809 20,000179 20,039550

510 20,078920 20,118291 20,157661 20,197032 20,236402 20,275773 20,315143 20,354513 20,393884 20,433254

520 20,472625 20,511995 20,551366 20,590738 20,630106 20,669477 20,708847 20,748218 20,787588 20,826959

530 20,866329 20,905699 20,945070 20,984440 21,023811 21,063181 21,102552 21,141922 21,181292 21,220663

540 21,260033 21,299404 21,338774 21,378145 21,417515 21,456885 21,496256 21,535626 21,574997 21,614367

550 21,653738 21,693108 21,732478 21,771849 21,811219 21,850590 21,889960 21,929331 21,968701 22,008072

560 22,047442 22,086812 22,126183 22,165553 22,204924 22,244294 22,283665 22,323035 22,362405 22,401776

570 22,441146 22,480517 22,519887 22,559928 22,598628 22,637998 22,677369 22,716739 22,756110 22,795480

580 22,834851 22,874221 22,913591 22,952962 22,992332 23,031703 23,071073 23,110444 23,149814 23,189184

590 23,228555 23,267925 23,307296 23,346666 23,386037 23,425407 23,464778 23,504148 23,543518 23,582889

600 23,622259 23,661630 23,701000 23,740371 23,779741 23,819111 23,858482 23,897852 23,937223 23,976593

610 24,015964 24,055334 24,094704 24,134075 24,173445 24,212816 24,252186 24,291557 24,330927 24,370297

620 24,409668 24,449038 24,488409 24,527779 24,567150 24,608520 24,645890 24,685261 24,724631 24,764002

630 24,803372 24,842743 24,882113 24,921483 24,960854 25,000224 25,039595 25,078965 25,118336 25,157706

640 25,197077 25,236447 25,275817 25,315188 25,354558 25,393929 25,433299 25,472670 25,512040 25,551410

650 25,590781 25,630151 25,669522 25,708892 25,748263 25,787633 25,827003 25,666374 25,905744 25,945115

660 25,984486 26,023856 26,063226 26,102596 26,141967 26,181337 26,220708 26,260078 26,299449 26,338819

670 25,378189 26,417560 26,456930 26,496301 26,535671 26,575042 26,614412 26,653782 26,693153 26,732523

680 26,771894 26,811264 26,850635 26,890005 26,929376 26,968746 27,008116 27,047487 27,086857 27,126228

690 27,165598 27,204969 27,244339 27,283709 27,323080 27,362450 27,401821 27,441191 27,480562 27,519932

700 27,559302 27,598673 27,638043 27,677414 27,716784 27,756155 27,795525 27,834895 27,874266 27,913636

710 27,953007 27,992377 28,031748 28,071118 28,110488 28,149859 28,189229 28,228600 28,267970 28,307341

720 28,346711 28,386081 28,425452 28,464822 28,504193 28,543563 28,582934 28,622304 28,661775 28,701045

730 28,740415 28,779788 28,819156 28,858527 28,897897 28,937268 29,976638 29,016008 29,055379 29,094749

740 29,134120 29,173490 29,212861 29,252231 29,291601 29,330972 29,370342 29,409713 29,449083 29,488454

750 29,527824 29,567191 29,606565 29,645935 29,685306 29,724678 29,764047 29,803417 29,842787 29,882158

760 29,921528 29,960899 30,000269 30,039640 30,079010 30,118380 30,157751 30,197121 30,236492 30,275862

770 30,315233 30,354603 30,393972 30,433344 30,472714 30,512085 30,551455 30,590825 30,630196 30,669566

780 30,708937 30,748307 30,787678 30,728048 30,866419 30,905789 30,945159 30,984530 31,023900 31,063271

790 31,102641 31,142012 31,181382 31,220752 31,260123 31,299493 31,338864 31,378234 31,417604 31,456975

800 31,496348 31,535716 31,575086 31,614457 31,653827 31,693198 31,732568 31,771938 31,811309 31,850679

810 31,890050 31,929420 31,963791 32,008161 32,047532 32,086902 32,126272 32,165643 32,205013 32,244384

820 32,283754 32,323125 32,362495 32,401866 32,441236 32,480606 32,519977 32,559347 32,598718 32,638088

830 32,677459 32,716829 32,756199 32,795570 32,834940 32,874311 32,913681 32,953052 32,992422 33,031792

840 33,071183 33,110533 33,149904 33,189274 33,228645 33,268015 33,307385 33,348756 33,386126 33,425497

850 33,464867 33,504238 33,543608 33,582979 33,622349 33,661719 33,701090 33,740460 33,779831 33,819201

860 33,858572 33,897942 33,937312 33,976683 34,016053 34,055424 34,094794 34,134165 34,173535 34,212905

870 34,252276 34,291648 34,331017 34,370387 34,409758 34,449128 34,448498 34,527869 34,567239 34,606610

880 34,645980 34,685351 34,724721 34,764091 34,803462 34,842832 34,882203 34,921573 34,960944 35,000314

890 35,039684 35,079055 35,118425 35,157796 35,197166 35,236536 35,275907 35,315277 35,354648 35,394018

900 35,433389 35,472759 35,512130 35,551500 35,590971 35,630241 35,669611 35,708982 35,748352 35,787723

910 35,827093 35,866464 35,905834 35,945204 35,984575 36,023945 38,083316 36,102866 36,142057 36,181427

920 38,220797 36,250168 36,299538 36,338909 36,378279 36,417650 36,457020 36,496390 36,535761 36,575131

930 36,614502 36,653872 36,693243 36,732613 36,771984 36,811354 38,850724 36,890095 36,929465 36,968836

940 37,008206 37,047576 37,086947 37,126317 37,165688 37,205058 37,244429 37,283799 37,323170 37,362540

950 37,410910 37,441201 37,480651 37,520022 37,559392 37,593765 37,638135 37,677503 37,716874 37,756244

960 37,795615 37,834985 37,874356 37,913726 37,953096 37,992467 38,031837 38,071208 38,110578 38,149949

970 38,189319 38,228689 38,268060 38,307430 38,346801 38,386171 38,425542 38,464912 38,504283 38,543653

980 38,563023 38,622394 38,661764 38,701135 38,740505 38,779876 38,819246 38,858616 38,897987 38,937357

990 38,976728 39,016098 39,055469 39,094839 39,134209 39,173580 39,212950 39,252321 39,291691 39,331062

Page 119: Esparragos y Tornillos Catalogo Tecnico

118DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

•C °F °C °F °C °F−73,3 −100 −148,0 37,8 100 212,0 151,7 305 581,0−70,6 −95 −139,0 40,6 105 221,0 154,4 310 590,0−67,8 −90 −130,0 43,3 110 230,0 157,2 315 599,0−65,0 −85 −121,0 46,1 115 239,0 160,0 320 608,0−62,2 −80 −112,0 48,9 120 248,0 162,8 325 617,0−59,4 −75 −103,0 51,7 125 257,0 165,6 330 626,0−56,7 −70 −94,0 54,4 130 266,0 168,3 335 635,0−53,9 −65 −85,0 57,2 135 275,0 171,1 340 644,0−51,1 −60 −76,0 60,0 140 284,0 173,9 345 653,0−48,3 −55 −67,0 62,8 145 293,0 176,7 350 662,0−45,6 −50 −58,0 65,6 150 302,0 179,4 355 671,0−42,8 −45 −49,0 68,3 155 311,0 182,2 360 680,0−40,0 −40 −40,0 71,1 160 320,0 185,0 365 689,0−37,2 −35 −31,0 73,9 165 329,0 187,8 370 698,0−34,4 −30 −22,0 76,7 170 338,0 190,6 375 707,0−31,7 −25 −13,0 79,4 175 347,0 193,3 380 716,0−28,9 −20 −4,0 82,2 180 356,0 196,1 385 725,0−26,1 −15 5,0 85,0 185 365,0 198,9 390 734,0−23,3 −10 14,0 87,8 190 374,0 201,7 395 743,0−20,6 −5 23,0 90,6 195 383,0 204,4 400 752,0−18,3 −1 30,2 93,3 200 392,0 207,2 405 761,0−17,8 0 32,0 96,1 205 401,0 210,0 410 770,0−15,0 5 41,0 98,9 210 410,0 212,8 415 779,0−12,2 10 50,0 101,7 215 419,0 215,6 420 788,0−9,4 15 59,0 104,4 220 428,0 218,3 425 797,0−6,7 20 68,0 l07,2 225 437,0 221,1 430 806,0−3,9 25 77,0 110,0 230 446,0 223,9 435 815,0−1,1 30 86,0 112,8 235 455,0 226,7 440 824,0

1,7 35 95,0 115,6 240 464,0 229,4 445 833,04,4 40 104,0 113,3 245 473,0 222,2 450 342,07,2 45 113,0 121,1 250 432,0 235,0 455 851,0

10,0 50 122,0 123,9 255 491,0 237,8 460 860,012,8 55 131,0 126,7 260 500,0 240,6 465 869,015,6 60 140,0 129,4 265 509,0 243,3 470 878,018,3 65 149,0 132,2 270 518,0 246,1 475 887,021,1 70 158,0 135,0 275 527,0 248,9 480 896,023,9 75 167,0 137,8 280 536,0 251,7 485 905,026,7 80 176,0 140,6 285 545,0 254,4 490 914,029,4 85 185,0 143,3 290 554,0 257,2 495 923,032,2 90 194,0 146,1 295 563,0 260,0 500 932,035,0 95 203,0 148,9 300 572,0 262,8 505 941,0

CONVERSION FORMULA INTERPOLATION FACTORS

ºC. = 5/9 (ºF. − 32)

ºF. = (9/5 ºC.) + 32

ºC ºF ºC ºF0,5561,1111,6672,2222,778

12345

1,803,605,407,209,00

3,3333,8894,4445,0005,556

6789

10

10,8012,6014,4016,2018,00

TEMPERATURE CONVERSION TABLELook up the temperature in the column indicated by an arrow and read ºC on the left or ºF to the right.

T T

T T T

CONVERSIÓN DE GRADOS FAHRENHEIT EN GRADOS CENTÍGRADOS Y VICEVERSA / CONVERSION OF DEGREES FAHRENHEIT INTO DEGREES CENTIGRADE AND VICE VERSA

Page 120: Esparragos y Tornillos Catalogo Tecnico

119DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

T T T

•C °F °C °F °C °F265,6 510 950 412,8 775 1427 560,0 1040 1904268,3 515 959 415,6 780 1436 562,8 1045 1913271,1 520 968 418,3 785 1445 565,6 1050 1922273,9 525 977 421,1 790 1454 568,3 1055 1931276,7 530 986 423,9 795 1463 571,1 1060 1940279,4 535 995 426,7 800 1472 573,9 1065 1949282,2 540 1004 429,4 805 1481 576,7 1070 1958285,0 545 1013 432,2 810 1490 579,4 1075 1967287,8 550 1022 435,0 815 1499 582,2 1080 1976290,6 555 1031 437,8 820 1508 585,0 1085 1985293,3 560 1040 440,6 825 1517 587,8 1090 1994296,1 565 1049 443,3 830 1526 590,6 1095 2003298,9 570 1058 446,1 835 1535 593,3 1100 2012301,7 575 1067 448,9 840 1544 596,1 1105 2021304,4 580 1076 451,7 845 1553 598,9 1110 2030307,2 585 1085 454,4 850 1562 601,7 1115 2039310,0 590 1094 457,2 855 1571 604,4 1120 2048312,8 595 1103 460,0 860 1580 607,2 1125 2057315,6 600 1112 462,8 865 1589 610,0 1130 2066318,3 605 1121 465,6 870 1598 612,8 1135 2075321,1 610 1130 468,3 875 1607 615,6 1140 2084323,9 615 1139 471,1 880 1616 618,3 1145 2093326,7 620 1148 473,9 885 1625 621,1 1150 2102329,4 625 1157 476,7 890 1634 623,9 1155 2111332,2 630 1166 479,4 895 1643 626,7 1160 2120335,0 635 1175 482,2 900 1652 629,4 1165 2129337,8 640 1184 485,0 905 1661 632,2 1170 2138340,6 645 1193 487,8 910 1670 635,0 1175 2147343,3 650 1202 490,6 915 1679 637,8 1180 2156346,1 655 1211 493,3 920 1688 640,6 1185 2165348,9 660 1220 496,1 925 1697 643,3 1190 2174351,7 665 1229 498,9 930 1706 646,1 1195 2183354,4 670 1238 501,7 935 1715 648,9 1200 2192357,2 675 1247 504,4 940 1724 651,7 1205 2201360,0 680 1256 507,2 945 1733 654,4 1210 2210362,8 685 1265 510,0 950 1742 657,2 1215 2219365,6 690 1274 512,8 955 1751 660,0 1220 2228368,3 695 1283 515,6 960 1760 662,8 1225 2237371,1 700 1292 518,3 965 1769 665,6 1230 2246373,9 705 1301 521,1 970 1778 668,3 1235 2255376,7 710 1310 523,9 975 1787 671,1 1240 2264379,4 715 1319 526,7 980 1796 673,9 1245 2273332,2 720 1328 529,4 985 1805 676,7 1250 2282385,0 725 1337 532,2 990 1814 679,4 1255 2291387,8 730 1346 535,0 995 1823 682,2 1260 2300390,6 735 1355 537,8 1000 1832 685,0 1265 2309393,3 740 1364 540,6 1005 1841 687,8 1270 2318396,1 745 1373 543,3 1010 1850 690,6 1275 2327398,9 750 1382 546,1 1015 1859 693,3 1280 2336401,7 755 1391 548,9 1020 1868 696,1 1285 2345404,4 760 1400 551,7 1025 1877 698,9 1290 2354407,2 765 1409 554,4 1030 1886 701,7 1295 2363410,0 770 1418 557,2 1035 1895 704,4 1300 2372

CONVERSIÓN DE GRADOS FAHRENHEIT EN GRADOS CENTÍGRADOS Y VICEVERSA / CONVERSION OF DEGREES FAHRENHEIT INTO DEGREES CENTIGRADE AND VICE VERSA

Page 121: Esparragos y Tornillos Catalogo Tecnico

120DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

T T T

•C °F °C °F °C °F707,2 1305 2381 835,0 1535 2795 965,6 1770 3218710,0 1310 2390 837,8 1540 2804 968,3 1775 3227712,8 1315 2399 840,6 1545 2813 971,1 1780 3236715,6 1320 2408 843,3 1550 2822 973,9 1785 3245718,3 1325 2417 846,1 1555 2831 976,7 1790 3254721,1 1330 2426 848,9 1560 2840 979,4 1795 3263723,9 1335 2435 851,7 1565 2849 982,2 1800 3272726,7 1340 2444 854,4 1570 2858 985,0 1805 3281729,4 1345 2453 857,2 1575 2867 987,8 1810 3290732,2 1350 2462 860,0 1580 2876 990,6 1815 3299735,0 1355 2471 862,8 1585 2885 993,3 1820 3308737,8 1360 2480 865,6 1590 2894 996,1 1825 3317740,6 1365 2489 868,3 1595 2903 998,9 1830 3326743,3 1370 2498 871,1 1600 2912 1001,7 1835 3335746,1 1375 2507 873,9 1605 2921 1004,4 1840 3344748,9 1380 2516 876,7 1610 2930 1007,2 1845 3353751,7 1385 2525 879,4 1615 2939 1010,0 1850 3362754,4 1390 2534 882,2 1620 2948 1012,8 1855 3371757,2 1395 2543 885,0 1625 2957 1015,6 1860 3380760,0 1400 2552 887,8 1630 2966 1018,3 1865 3380762,8 1405 2561 890,6 1635 2975 1021,1 1870 3398765,6 1410 2570 893,3 1640 2984 1023,9 1875 3407768,3 1415 2579 896,1 1645 2993 1026,7 1880 3416771,1 1420 2588 898,9 1650 3002 1029,4 1885 3425773,9 1425 2597 901,7 1655 3011 1032,2 1890 3434776,7 1430 2606 904,4 1660 3020 1035,0 1895 3443779,4 1435 2615 907,2 1665 3029 1037,8 1900 3452782,2 1440 2624 910,0 1670 3038 1040,6 1905 3461785,0 1445 2633 912,8 1675 3047 1043,3 1910 3470787,8 1450 2642 915,6 1680 3056 1046,1 1915 3479790,6 1455 2651 918,3 1685 3065 1048,9 1920 3488793,3 1460 2660 921,1 1690 3074 1051,7 1925 3497796,1 1465 2669 923,9 1695 3083 1054,4 1930 3506798,9 1470 2678 926,7 1700 3092 1057,2 1935 3515801,7 1475 2637 929,4 1705 3101 1060,0 1940 3524804,4 1480 2696 932,2 1710 3110 1062,8 1945 3533807,2 1485 2705 935,0 1715 3119 1065,6 1950 3542810,0 1490 2714 937,8 1720 3128 1068,3 1955 3551812.8 1495 2723 940,6 1725 2137 1071,1 1960 3560815,6 1500 2732 943,3 1730 3146 1073,9 1965 3569818,3 1505 2741 946,1 1735 3155 1076,7 1970 3578821,1 1510 2750 948,9 1740 3164 1079,4 1975 3587823,9 1515 2759 951,7 1745 3173 1082,2 1980 3596826,7 1520 2768 954,4 1750 3182 1085,0 1985 3605829,4 1525 2777 957,2 1755 3191 1087,8 1990 3614832,2 1530 2786 960,0 1760 3200 1090,6 1995 3623

962,8 1765 3209 1093,3 2000 3632

CONVERSIÓN DE GRADOS FAHRENHEIT EN GRADOS CENTÍGRADOS Y VICEVERSA / CONVERSION OF DEGREES FAHRENHEIT INTO DEGREES CENTIGRADE AND VICE VERSA

Page 122: Esparragos y Tornillos Catalogo Tecnico

DIMECO T.I.

121DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

Technical Data

Page 123: Esparragos y Tornillos Catalogo Tecnico

122DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

for screw fastenings - DIN - ISO 898.1 / EN 20898-2QUALITY STANDARDS

We believe that it is of great importance for our clients to be aware of the standards which govern our pro-duction, and we therefore provide below an extract of the ISO.898.1 and EN-20898-2 Standards, which cover the technical specifications for the supply of screws and nuts.

EXECUTIONThe execution of commercial fasteners relates to quality m (medium).

THREAD TOLERANCESThe areas of tolerance for commercial screw fasteners and nuts are: Screw, 6g - Nut, 6 H.

ISO 898.1 SCREW FASTENERS

DESIGNATION SYSTEMThe designation system for the tensile strength class is as follows:The designation consists of two numbers separated by a point. The first number indicated 1/10 of the tensile strength in kg/mm2.

First number 5 8 10 12

Minimum tensile strengthσB Kg/mm2 50 80 100 120

The second number indicates the decuple of the ratio between the yield point and the minimum tensile strength.

Second number 6 8 9

Yield point σsMinimum tensile strength σB

10 6 8 9

The product of the two numbers give the yield point in kg/mm2.

MECHANICAL PROPERTIESThe following tables shows the mechanical properties coordinated with the classes of tensile strength and are used for finished screw fasteners.

Page 124: Esparragos y Tornillos Catalogo Tecnico

123DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

for screw fasteners ISO 898.1 QUALITY STANDARDS

a- For studs of quality class 8.8 with diameters of d ≤ 16 mm, there exists a serious risk that the thread will be pulled off the screw in the event of inadvertent over-torquing, which would give rise to a load greater than the test load. It is recommended to refer to ISO Standard 898-2 in this respect.

b- Only applicable to nominal thread diameters of d ≤ 16 mm.c- For fasteners intended for metal structures, the limit is 12 mm.d- The minimum characteristics for tensile strength are applicable to products with a nominal length of l ≥ 2,5 d. The minimum hardness is valid for products with a

length of l < 2,5 d and for other products which cannot be subjected to tensile testing (for example, due to the head configuration).e- When complete bolts, screws, and studs are tested, the breaking loads applicable for the calculation of Rm should comply with the values given in tables 6 and 8 (ISO 898.1).f- A measurement of hardness effected at the end of bolts, screws and studs should be a maximum of 250 HV, 238 HB, or 99.5 HRB.g- The surface hardness should be no greater than 30 Vickers points greater than the measured hardness of the central core of the product, when both measurements are taken

with HV 0.3. For quality class 10.9, any increase in surface hardness which suggests than this is exceeds 390 HV is unacceptable.h- In cases where the lower elastic limit R eL cannot be determined, the conventional elastic limit at 0.2%, R p0,2 may be measured. For quality classes 4.8, 5.8, and 6.8, the

values of R eL are given solely for the requirements of the calculation, and are not test values.i- The ratio of the apparent elastic limit, as defined in the designation of the quality class, and the conventional elastic limit at 0.2%, R p0,2, are obtained from measurements

effected using samples. When these measurements are obtained from measurements taken from complete bolts and screws, they will vary as a result of the effects of size and the production method.

Sec-tion no.

Mechanical and physical characteristics

Quality class

3.6 4.6 4.8 5.6 5.8 6.8 8.8 a 9.8 b 10.9 12.9d ≤ 16c

mmd > 16c

mm

5.1 Nominal tensile strength, R m, nom N/mm2 300 400 500 600 800 800 900 1.000 1.200

5.2. Nominal tensile strength, R m, min. d,e N/nm2 330 400 420 500 520 600 800 830 900 1.040 1.220

5.3Vickers Hardness, HV

F ≥98 N

min. 95 120 130 155 160 190 250 255 290 320 385

max. 220f 250 320 335 360 380 435

5.4Brinell Hardness, HB

F =30 D2

min. 90 114 124 147 152 181 238 242 276 304 366

max. 209f 238 304 318 342 361 414

5.5 Rockwell Hardness, HR

min. HRB 52 67 71 79 82 89

HRC 22 23 28 32 39

max. HRB 95,0F 99,5

HRC 32 34 37 39 44

5.6 Surface Hardness, HV 0,3 max. g

5.7 Lower elastic limit, ReLh, N/mm2nom. 180 240 320 300 400 480

min. 190 240 340 300 420 480

5.8Conventional elastic limit at

0,2%, Rp0,2i, N/mm2

nom. 640 640 720 900 1080

min. 640 660 720 940 1100

5.9 Tension at test load, Sp

Sp/ReL o Sp/Rp 0,2

0,94 0,94 0,91 0,93 0,9 0,92 0,91 0,91 0,9 0,88 0,88

N/mm2 180 225 310 280 380 440 580 600 650 830 970

5.10 Breaking torque, MB Nm min. Please see Standard ISO 898-7

5.11 Percentage stretching following breakage, A min. 25 22 20 12 12 10 9 8

5.12 Reduction in section following breakage, Z % min. 52 48 48 44

5.13Strain or tensile strength under wedge

load e

Values for full-sized bolts and screws (not including studs) should not be less that theminimum tensile strength values indicated in section 5.2.

5.14 Impact strength, KU J min. 25 30 30 25 20 15

5.15 Solidity of head Without breakage

5.16

Minimum height of non-decarbonised areain the threaded area, E

1/2 H1 _H1 3/4 H1

Maximum depth of completedecarbonisation, G

mm 0,015

5.17 Hardness after second tempering Maximum reduction in hardness of 20 HV.

5.18 Surface integrity In compliance with ISO Standard 6157-1 or ISO Standard 6157-3, as appropriate

Page 125: Esparragos y Tornillos Catalogo Tecnico

124DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

a- The boron content may be as high as 0.005% provided that the non effective boron is controlled by the addition of titanium and/or aluminium.

b- Easily worked steel is permitted for these quality classes, with maximum content in sulphur, phosphorus, and lead as follows: sulphur 0.34%; phosphorus 0.11%; lead 0.35%.

c- For nominal diameters of 20 mm the steels specified for class 10.9 may be necessary in order to achieve sufficient quenchability.

d- In the case of steel alloyed with boron and with a carbon content of less than 0.25% (crucible test), the minimum content of manganese should be 0.6% for quality class 8.8, and 0.7% for classes 9.8, 10.9, and 10.9.

e- In addition, the products should be identified by underlining the quality class designator (please refer to Chapter 9). All the characteristics of class 10.9, such as the specifications given in Table 3, should be met for class 10.9; nevertheless, because of its lower tempering temperature, different characteristics from those obtained at high temperatures are found.

f- For materials of these quality classes, an attempt should be made to ensure that they possess sufficient quenchability to guarantee a structure of approxi-mately 90% martensite in the central core of the threaded sections in the case of fasteners after quenching and before tempering.

g- This steel alloy should contain a minimum of one of the following elements in the minimum quantity shown: chrome, 0.30%; nickel, 0.30%; molybdenum, 0.20%; vanadium, 0.10%. When the elements are specified in combinations of two, three, or four, and they possess alloy contents lower than those quoted above, the limiting value applicable when determining the class is 70% of the sum of the individual limiting values shown above for two, three, or four elements respectively.

h- For quality class 12.9 a layer enriched with white phosphorus detectable by metallography is not allowed in surfaces subject to tensile forces.

i- The chemical composition and the quenching temperature are being investigated.

ClassQuality

Materials and treatments

Limits of chemical composition(verification analysis) % (m/m)

Tempering tempera-

ture

C P S Bª ºC

min max. max. max. max. min.

3.6 b

Carbon steel

- 0.2 0.05 0.06 0.003 -

4.6 b

- 0.55 0.05 0.060.003 -

4.8 b

5.6 b 0.13 0.55 0.05 0.06 0.003 -

5.8 b

- 0.55 0.05 0.066.8 b

8.8 c

Carbon steel with additives (for example, B, Mn, or Cr), quenched and tempered

0.15d 0.4 0.035 0.035 0.003 425

Carbon steel, quenched and tempered 0.25 0.55 0.035 0.035

9.8Carbon steel with additives (for example, B,

Mn, or Cr), quenched and tempered0.15d 0.35 0.035 0.035 0.003 425

Carbon steel, quenched and tempered 0.25 0.55 0.035 0.035

10.9 e f arbon steel with additives (for example, B, Mn, or Cr), quenched and tempered

0.15d 0.35 0.035 0.035 0.003 340

10.9 f

Carbon steel, quenched and tempered 0.25 0.55 0.035 0.035 0.003 425

Carbon steel with additives (for example, B, Mn, or Cr), quenched and tempered

0.20d 0.55 0.035 0.035

Carbon steel, quenched and tempered g 0.2 0.55 0.035 0.035

12.9 f h i Carbon steel, quenched and tempered g 0.28 0.5 0.035 0.035 0.003 380

for screw fasteners ISO 898.1 QUALITY STANDARDS

Page 126: Esparragos y Tornillos Catalogo Tecnico

125DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

for nuts according to UNE - EN 20898-2QUALITY STANDARDS

STRENGTH CLASSESNuts.

DESIGNATION SYSTEMStrength classes for nuts are designated with a number corresponding to the 1/10 of the test tensile strength in kg/mm. This test strength corresponds to the minimum tensile strength of a screw in kg/mm2, to which the nut has to be joined when the minimum breaking load bearing capacity of the screw is to be assured.

MATERIALSNuts are manufactured in steel in compliance with the limits specified in the following table for the chemical composition.

Quality class

Limits of chemical composition(analysis of the composition), %

C Mn P S

max. min. max. max.

41); 51); 61) — 0.500 — 0.060 0.150

8; 9 041) 0.580 0.250 0.060 0.150

102) 052) 0.580 0.300 0.048 0.058

122) — 0.580 0.450 0.048 0.058

1) Nuts of these quality classes may be manufactured from easily worked steels, unless otherwise agreed between the purchaser and the manufacturer. In such cases, the following maximum content in sulphur, phosphorus, and lead are acceptable:

sulphur 0.34%; phosphorus 0.11%; lead 0.35%.

2) If necessary alloying elements may be added in order to improve the mechanical characteristics of the nuts.

Page 127: Esparragos y Tornillos Catalogo Tecnico

126DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

for nuts according to UNE - EN 20898-2QUALITY STANDARDS

MECHANICAL PROPERTIESThe mechanical properties coordinated by tensile strength classes are shown below, as used for specific nuts:

Thread

Quality class

04 05 4

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Greater than up to N/mm2 min. max. State Type N/mm2 min. max. State Type N/mm2 min. max. State Type

M4

380 188 302 NTR1) fina 500 272 353 TR2) fina- - - - -

M4 M7

M7 M10

M10 M16

M16 M39 510 117 302 NTR1) 1

Thread

Quality class

53) 6 8

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

VickersHardness,

HV Screw

Greater than up to N/mm2 min. max. State Type N/mm2 min. max. State Type N/mm2 min. max. State Type N/mm2 min. max. State Type

- M4 520

130302 NTR1) 1

600

150302 NTR1) 1

800 180

302 NTR1)

1- - - - -

M4 M7 580 670 855

200M7 M10 590 680 870

M10 M16 610 700 880

M16 M39 630 146 720 170 920 233 353 TR2) 890 180 302 NTR1) 2

Thread

Quality class

9 10 12

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

Vickers Hardness,

HV Screw

Tensile strength

Sp

VickersHardness,

HV Screw

Greater than up to N/mm2 min. max. State Type N/mm2 min. max. State Type N/mm2 min. max. State Type N/mm2 min. max. State Type

M4 900 170

302 NTR1) 2

1 040

272 353 TR2) 1

1 140

295 353 TR2) 1

1 150

272 353 TR2) 2

M4 M7 915

188

1 040 1 140 1 150

M7 M10 940 1 040 1 140 1 160

M10 M16 950 1 050 1 170 1 190

M16 M39 920 1 060 - - - - - 1 200

1) NTR = Not quenched or tempered.2) TR = Quenched and tempered.3) The maximum hardness of studs of quality classes 5.6 y 5.8 is to be reduced to 220 HV in the next edition of the ISO Standard 898-1:1988. This is the maximum hardness of the bolt in the working surface of the thread, where only the end (run-out) of the screw or the head may have a maximum hardness of 250 HV. Consequently, the test forces are based upon a maximum hardness for the stud of 220 HV.NOTE: Minimum hardness is only required for heat-treated nuts, and nuts which are too large to be subjected to the load test. For all other nuts, the minimum hardness is given purely for illustrative purposes. For nuts which are neither quenched nor tempered and which satisfy the load test, the minimum hardness should not be cause for rejection.

Page 128: Esparragos y Tornillos Catalogo Tecnico

127DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

INFLUENCE OF THE CHEMICAL ELEMENTS IN STEELS

Steel alloys using difference chemical elements are produced in order to improve the physical properties of the material and to achieve special properties:

Carbon (C)Although this is not considered to be an alloying element, it is the most important component in steel. It improves tensile strength, hardness, and abrasion resistance. It reduces ductility, rigidity, and machining.

Manganese (Mn)This is an oxidiser and degasifier, and reacts with sulphur to improve forgeability. It increases tensile strength, hardness, and durability.

Phosphorus (P)This increases tensile strength and hardness and improves machinability. It causes fragility in steel.

Sulphur (S)Improves machining qualities in the presence of manganese. It reduces weldability, impact, roughness, and ductility.

Silicon (Si)This is a deoxidiser and degasifier. It increases tensile strength, elasticity, hardness, and forgeability.

Chromium (Cr)Increase breaking strength, hardness, durability, roughness, and resistance to high temperatures.

Nickel (Ni)This raises strength and hardness, while maintaining ductility and rigidity. It increases resistance to cracking and high temperatures.

Molybdenum (Mo)This increases strength, hardness, durability, and rigidity, together with resistance to cracking and to high temperatures.

Titanium (Ti)This is used as a stabilising element in stainless steels. It has a great affinity for carbon.

Page 129: Esparragos y Tornillos Catalogo Tecnico

128DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PROPERTIES OF STEELS

QUALITY PROPERTY

B6

Good resistance in corrosive environments (crude oil, petroleum, organic acids, organic

solvents, ammonia), but not in highly corrosive environments. Good resistance to corrosion up

to a temperature of 650ºC, good weldability.

B7Good strength and hardness, above all for uses in conditions of high T (-10°C / +427°C).

Applications: Petrochemicals, valves, pumps.

B7MSimilar to B7 but with lower mechanical properties.

Applications: Petrochemical Industry.

B16Prescribed for good strength and hardness in conditions of high T (-10°C / +558°C).

Applications: Petrochemical Industry.

B8 (A-193)

Used in temperatures of between -196°C and +538°C. Good resistance to intercrystalline

corrosion, and excellent weldability.

Applications: Petrochemicals, chemicals, pharmaceuticals, foodstuffs, ironwork.

B8 (A-320)Good resistance to corrosion. Suitable for uses at low temperatures (-254°C / +50°C).

Applications: Chemical, pharmaceutical, and foodstuffs industries.

B8M (A-193)Excellent resistance to intercrystalline corrosion and to corrosion caused by Cl ions.

Temperature range (-196°C/ + 538°C).

B8M (A-320)Good resistance to corrosion. Indicated for temperatures between -196°C and +50°C).

Applications: Chemical and petrochemical industries.

B8C (A-193)

High resistance to intergranular corrosion and oxidation. Used for temperatures of (-196°C /

+538°C). Applications: Petrochemical industry, changes of temperature, and in the construction

of structures for chemical plants.

B8C (A-320)Good resistance to corrosion. Indicated for temperatures of (-254°C/ + 50°C). Applications:

Chemical and petrochemical industries.

B8T (A-193)

Indicated for the range of temperatures between (-196°C/ + 538°C). High resistance to

intergranular corrosion thanks to the presence of Titanium. Good weldability without the

requirement for additional heat treatment. Applications: Petrochemical, chemical, foodstuffs

industries, and energy generator plants.

B8T (A-320) Used for temperatures of (-101ºC /+50°C). Applications: Petrochemical Industry.

B5For use in high temperature conditions.

Applications: Petrochemical industry, valves and flanges.

Page 130: Esparragos y Tornillos Catalogo Tecnico

129DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

PROPERTIES OF STEELS

QUALITY PROPERTY

GR.660Excellent mechanical properties for use at high temperatures.

Applications: Pressure equipment and flanges

L7Good strength and hardness, excellent for use at low T (-101ºC / +50°C).

Applications: Petrochemical Industry.

L7MSimilar to L7 but with lower mechanical properties.

Applications: Petrochemical Industry.

Monel 400

High strength, good weldability, perfect resistance to corrosion under a wide range of T and

conditions (sea water, mineral and organic acidity). Applications: Valves, pumps, marine

installations, petrochemical plants, changes of temperature, and for uses in contact with

sulphuric and hydrochloric acids.

Monel 500Greater mechanical strength and resistance to abrasion than Monel 400.

Applications: Valve, pumps, petrochemical plants, and fasteners.

Inconel 600

Excellent resistance to both oxidising and reducing environments, as well as in corrosive

environments at high T.

Applications: Equipment for the chemical, textile, and foodstuffs industries, kilns.

Inconel 625Great mechanical strength from cryogenic T up to very high T (1100 °C). Excellent resistance to

fatigue and oxidation. Applications: Chemical industry, marine equipment, pipes and valves.

Incoloy 800H

Resistance to corrosion and carbonisation at high T (up to 1100ºC).

Resistant to attack by sulphides, corrosion and pickling.

Applications: Changes of temperature, heat equipment, generators.

Incoloy 825

Excellent resistance to breaking due to corrosion, resistant to oxidising and reducing

environments.

Applications: Deoxidising tanks, chemical industry, pollution control systems.

Hastelloy C276

Good resistance to breaking due to corrosion in the presence of chlorine compounds, resistance

to intercrystalline corrosion. Applications: Employed in environments with sever chemical

processes, in the paper industry, and in pollution control.

Duplex 2205Very high resistance to breaking due to corrosion.

Applications: Chemical and oil industries, pipes, flanges, valves for use at high T.

Superduplex

32760

Perfect resistance to interstitial corrosion and corrosive environments.

Applications: Marine installations and petrochemical industries.

Page 131: Esparragos y Tornillos Catalogo Tecnico

130DIMECO TÉCNICAS INDUSTRIALES • www.dimecoti.com • [email protected]

DIMECO T.I.

METALLIC PRODUCTS EN 10204:2004Types of inspection documents

EN 10204 Reference

Designation of the document type

Document content Document validated by

Type 2.1 Declaration of compliance with the order

Statement of compliance with the order

The manufacturer

Type 2.2 Test report Statement of compliance with the order, with indication of results of nonspecific inspection

The manufacturer

Type 3.1 Inspection certificate 3.1 Statement of compliance with the order, with indication of results of specific inspection

The manufacturer’s authorized inspection representative independent of the manufacturing departament

Type 3.2 Inspection certificate 3.2 Statement of compliance with the order, with indication of results of specific inspection

The manufacturer’s authorized inspection representative independent of the manufacturing departament and either the purchaser’s authorized inspection representative or the inspector designated by the official regulations