Download - Tarjeta 3 Ejes TB6560 Roja
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
1 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Tarjeta de Control 3 ejes
Roja TB65603V2 Tarjeta Controladora 3 ejes Toshiba TB6560AHQ
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
2 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Caractersticas:
Controladora para 3 Motores Bipolares de 4, 6 u 8 hilos los cuales
pueden operar simultneamente
Fuente de alimentacin de Corriente Directa, recomendable a 24
Volts
Circuitos integrados Toshiba TB6560AHQ 3.5 Amperes por eje.
Micropasos 1,1/2, 1/4, 1/16 para mayor precisin
Corriente ajustable por eje - 25%,50%,75%,100%
Proteccin contra sobre-Carga, Sobre-corriente y temperatura
Interfase paralela opto-aislada
Relevador mecnico interno para controlar una salida de hasta 10
Amperes
4 Canales de entrada, limites o EStop
Suporta la mayora de los software de control CNC por puerto
paralelo MACH3,KCAM4,EMC2 etc.
Entradas por Puerto DB25 Paralelo
Expansin a cuarto eje ya que da acceso a las seales para colocar
un Driver Externo
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
3 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
4 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Pines del Puerto DB25 Paralelo
DB25 Pines
del Puerto DB25
Notas
1 EN Habilita todos los ejes
2 STEPX X Seal de Paso
3 DIRX X Seal de Direccin
4 STEPY Y Seal de Paso
5 DIRY Y Seal de Direccin
6 STEPZ Z Seal de Paso
7 DIRZ Z Seal de Direccin
10 LIMIT-1 Entrada Limite 1
11 LIMIT-2 Entrada Limite 2
12 LIMIT-3 Entrada Limite 3
13 LIMIT-4 Entrada Limite 4
14 Relay control Relevador Mecanico
15 blank No se USa
16 STEPB- B4to eje) Seal de Paso
17 DIRB- B(4th axis) Seal de Direccin
18-25 GND GND
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
5 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Switches
Modo de Operacin (1 y 2), Micro-pasos (3 y 4)
Modo de Operacin
Decaimiento de la corriente.- El tiempo que toma la corriente para
decaer. Rpidos decaimientos de corriente son utilizados para mejorar la
forma de onda sinusoidal en los controladores de micropasos. El
decaimiento de la corriente depende de la constante de tiempo L/R, de
la tensin de bloqueo aplicada y del Motor a pasos utilizado
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
6 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
ON/ON100%
OF/ON50%
ON/OF25%
OF/OF0%
Switch 1 Switch 2 Modo
ON ON Fast decay
OFF ON 50% fast decay
ON OFF 25% fast decay
OFF OFF Slow decay
Micro-pasos
Switch 3 Switch4 Micopasos
ON ON 1/8
OFF ON 1/16
ON OFF 1/2
OFF OFF 1
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
7 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Configuracin de corriente hacia los Motores:
Swich 1 Switch 2 Corriente ON ON 20% de 3Amp
OFF ON 50% de 3 Amp
ON OFF 75% de 3 Amp
OFF OFF 100% de 3Amp
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
8 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Conexin de Motores:
Motor de 4 Cables
Motor de 6 Cables
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
9 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Motor de 8 Cables Conexin Serie
Motores a pasos:
Pueden usarse motores a pasos de 4, 6 u 8 hilos que consuman
menos de 3.5 Amperes cada uno.
Wiring Diagram:
Simple introductions:
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
10 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Instrucciones para configurar: 1.- Conectar los Motores a pasos de acuerdo a la informacin previa y ajustar los switches de corriente de acuerdo al consumo de los Motores a colocar. 2.- Instalar programa mach3 Para bajar el programa mach3 utilice la siguiente liga conectando a Internet: http://www.opencncmexico.com/Mach3Version3.043.022.exe Despus de instalar el programa mach3 hay que reiniciar la computadora forzosamente para la correcta instalacin del driver del programa mach3 Descargue el manual del programa mach3 y selo como referencia en caso de alguna duda con el programa: http://www.machsupport.com/docs/Mach3Mill_1.84.pdf 3.- Configurar la salida para la habilitacin de los 3 ejes de la tarjeta.
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
11 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Para habilitar X, Y y Z Port = 1 y Pin Number = 1 Nota: Si no habilita la salida de los Controladores estos no se energizaran.
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
12 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
4.- Configurar las salidas de los ejes:
Eje X Enable = Paloma Step Pin = 2 Dir Pin = 3 Eje Y Enable = Paloma Step Pin = 4 Dir Pin = 5 Eje Z Enable = Paloma Step Pin = 6 Dir Pin = 7 Eje Externo Eje A Enable = Paloma Step Pin = 16 Dir Pin = 17
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
13 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
5.- Entrada de paro de Emergencia ESTOP y Entradas de Limites (Home) Paro de Emergencia:
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
14 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Entradas de Limites (Home)
Home Eje X Enable = Paloma Pin Number = 11 Active Low = OK Home Eje Y Enable = Paloma Pin Number = 12 Active Low = OK Home Eje Z Enable = Paloma Pin Number = 13 Active Low = OK
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
15 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
6.- Configuraciones para encendido de Herramienta
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
16 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Encender la herramienta con el botn Spindle
-
WWW.OPENCNCMEXICO.COM CONFIGURACIONES FISICAS X, Y,Z Y PROGRAMA DE CONTROL MACH3
17 (17)
Prepared (also subject responsible if other) No. OPNCNCINA / Isaac Navarro 220612_01
Approved Checked Date Rev Reference
Ing Isaac N. OPNCNCINA Error!
22/06/2012 B
Conexin Motores a pasos de 300oz-in