presentation4 ata
Post on 16-Apr-2017
240 Views
Preview:
TRANSCRIPT
Recommendationsfor Conversion to
Guidelines
What are ATA 100 Specs• It establishes standards for the
presentation of certain data produced by aircraft, engine, and component manufacturers which is required for support of their products.
standards?
presentation of data
required for support
• It minimizes cost and effort of operators to make the manufacturer’s data more compatible for the publishers, engineers, airframe manufacturers, owners, and mechanics.
A D V A N T A G E Sminimizes cost
compatible
•FORMAT•STYLE•METHOD
General Rules
• FORMAT ( page & text )– Header / Footer Info
• Manufacturer, Model, Effectivity, Chapt-Sec-Sub, Date, Page Numbering
– Type Size• 10 to 12 pt Sans Serif Font (ARIAL)
– 6 Lines per Inch• An inch is 72 points, so 6 lpi is paragraph
spacing of Exactly 12 points
General Rules
This ONLY works on10 pt. Arial font.
• FORMAT ( Chapter – Section – Sub-Section )– Each Chapter represents a SystemChapters in Illustrated Parts Catalog:
72-00-00 Reciprocating Engine73-00-00 Engine and Fuel Control74-00-00 Ignition76-00-00 Engine Controls
General Rules
• FORMAT ( Chapter – Section – Sub-Section )– Each Section represents a Sub-System72-00-00 Reciprocating Engine (General)
72-10-00 Front Section72-20-00 Power Section72-30-00 Cylinder Section72-40-00 Supercharger Section74-50-00 Lubrication
General Rules
• FORMAT ( Chapter – Section – Sub-Section )– Each Sub-Section coordinates with a Page Block
– EXAMPLE: 74 — 20 — 01 Chapter Section Fault IsolationFault Isolation Ignition Distribution
General Rules
System Description 1-99Fault Isolation 101-199Special Procedure 201-299Removal 301-399Installation 401-499Disassembly 501-599Cleaning 601-699Unassigned 701-799
Inspection/Check 801-899Repair 901-999Assembly 1001-1099Servicing (72-00-00 only) 1101-1199Storage (& transportation) 1201-1299Testing 1301-1399Rework (SB Instructions) 1401-1499
• FORMAT ( indexing )– LEP, TOC, & Page/Figure Numbering
• Page numbers further subdivide information.
General Rules
System Description……...1-99Fault Isolation………..101-199Special Procedures…201-299Removal………………301-399Installation…………….401-499Disassembly…………501-599Cleaning……..............601-699Unassigned….............701-799Inspection/Check…….801-899 Etc…
• FORMAT ( indexing )– LEP, TOC, & Page/Figure Numbering
• Page numbers further subdivide information.
General Rules
System Description……...1-99Fault Isolation………..101-199Special Procedures….201-299Removal………………301-399Installation…………….401-499Disassembly…….……501-599Cleaning……...............601-699Unassigned…..............701-799Inspection/Check…….801-899 Etc…
• FORMAT ( indexing )– LEP, TOC, & Page/Figure Numbering
• Figure numbering style matches page numbering.
General Rules
System Description……...1-99Fault Isolation………..101-199Special Procedures…201-299Removal………………301-399Installation…………….401-499Disassembly…………500-599Cleaning……..............600-699Unassigned….............701-799Inspection/Check…….801-899
• FORMAT ( indexing )– Main TOC should be more concise– Chapter TOC should have more detail
General RulesChap
ter TOC
NOT PRACTICAL
on small
man
uals
•METHOD1. Major Breakdown
A. Major Subdivision
(1) Steps of Procedure(a) Any further breakdown of the steps
1 Any necessary further breakdown
a Any necessary further breakdown
General Rules
Chapter-Section-Subject will be in the footer 73-10-05
•METHODWARNING:CAUTION:NOTE:
General Rules
•METHODWARNING: ENTIRE WARNING IS IN ALL CAPITAL LETTERS, UNDERLINED, ABOVE AND VERTICALLY ALIGNED WITH THE STEPS THEY APPLY TO.
General Rules
•METHODCAUTION: ENTIRE CAUTION IS IN ALL CAPITAL LETTERS, UNDERLINED, ABOVE AND VERTICALLY ALIGNED WITH THE STEPS THEY APPLY TO.
General Rules
•METHODNOTE: These are in upper/lower case, underlined, directly below and vertically aligned to the text they affect.
General Rules
•METHODWARNING:CAUTION:NOTE:
General Rules
•Illustrated Parts CatalogGeneral RulesGeneral Rules
• IPC Table of ContentsGeneral RulesGeneral Rules
MAINTENANCE MANUAL72-00-00 Reciprocating Engine MaintenancePower SectionSystem Description 72-20-00 1-99Power Section Maintenance 1. General 2. Crankcase 3. Crankshaft and Counterweights 4. Camshaft 5. BearingsFault Isolation 72-20-01 101-199 1. Crankcase 2. Crankshaft and Counterweights 3. Camshaft
ILLUSTRATED PARTS CATALOG72-00-00 Reciprocating Engine
72-10-00 Front Section1. Propeller Drive Assy.
72-20-00 Power Section1. Crankcase Assy.2. Crankshaft Idler Gears
72-30-00 Cylinder Section1. Connecting Rods, Pistons2. Valve Assy.
72-40-00 Supercharger Section1. Compressor Mounting
Parts2. Intake Pipes, Air Inlet
74-50-00 Lubrication1. Oil Sump and Induction
Housing
M MM MDivided Divided
bybyProcedureProcedure
ss
IPCIPCDivided by Divided by SystemsSystems
Recommendationsfor Conversion to
Guidelines
top related